Abstract: The relationship between different types of Molybdenum disulfide greases under extreme pressure loading and different speed situations have been studied using Design of Experiment (DOE) under 1200rpm steady state rotational speed and cyclic frequencies between 2400 and 1200rpm using a Plint machine software to set up the different rotational speed situations.
Research described here is aimed at providing good friction and wear performance while optimizing cyclic frequencies and MoS2 concentration due to the recent concern about grease behavior in extreme pressure applications. Extreme load of 785 Newton was used in conjunction with different cyclic frequencies (2400rpm -3.75min, 1200rpm -7.5min, 2400rpm -3.75min, 1200rpm -7.5min), to examine lithium based grease with and without MoS2 for equal number of revolutions, and a total run of 36000 revolutions; then compared to 1200rpm steady speed for the same total number of revolutions. 4 Ball wear tester was utilized to run large number of experiments randomly selected by the DOE software. The grease was combined with fine grade MoS2 or technical grade then heated to 750C and the wear scar width was collected at the end of each test. DOE model validation results verify that the data were very significant and can be applied to a wide range of extreme pressure applications. Based on simulation results and Scanning Electron images (SEM), it has been found that wear was largely dependent on the cyclic frequency condition. It is believed that technical grade MoS2 greases under faster cyclic speeds perform better and provides antiwear film that can resist extreme pressure loadings. Figures showed reduced wear scars width and improved frictional values.
Abstract: The governing differential equations of laminated
plate utilizing trigonometric shear deformation theory are derived
using energy approach. The governing differential equations
discretized by different radial basis functions are used to predict the
free vibration behavior of symmetric laminated composite plates.
Effect of orthotropy and span to thickness ratio on frequency
parameter of simply supported laminated plate is presented.
Numerical results show the accuracy and good convergence of radial
basis functions.
Abstract: Optical network uses a tool for routing called Latin
router. These routers use particular algorithms for routing. For
example, we can refer to LDF algorithm that uses backtracking (one
of CSP methods) for problem solving. In this paper, we proposed
new approached for completion routing table (DRA&CRA
algorithm) and compare with pervious proposed ways and showed
numbers of backtracking, blocking and run time for DRA algorithm
less than LDF and CRA algorithm.
Abstract: In this study, a three-dimensional haptotaxis model to simulate the migration of a population of cancer cells has been proposed. The invasion of cancer cells is related with the hapto-attractant and the effect of the interface energies between the cells and the ECM. The diffuse interface model, which incorporates the haptotaxis mechanism and interface energies, is employed. The semi-implicit Fourier spectral scheme is adopted for efficient evaluation of the simulation. The simulation results thoroughly reveal the dynamics of cancer-cell migration.
Abstract: Mobile ad hoc network is a collection of mobile
nodes communicating through wireless channels without any
existing network infrastructure or centralized administration.
Because of the limited transmission range of wireless network
interfaces, multiple "hops" may be needed to exchange data
across the network. Consequently, many routing algorithms
have come into existence to satisfy the needs of
communications in such networks. Researchers have
conducted many simulations comparing the performance of
these routing protocols under various conditions and
constraints. One question that arises is whether speed of nodes
affects the relative performance of routing protocols being
studied. This paper addresses the question by simulating two
routing protocols AODV and DSDV. Protocols were
simulated using the ns-2 and were compared in terms of
packet delivery fraction, normalized routing load and average
delay, while varying number of nodes, and speed.
Abstract: The sonochemical decolorization and degradation of azo dye Methyl violet using Fenton-s reagent in the presence of a high-frequency acoustic field has been investigated. Dyeing and textile effluents are the major sources of azo dyes, and are most troublesome among industrial wastewaters, causing imbalance in the eco-system. The effect of various operating conditions (initial concentration of dye, liquid-phase temperature, ultrasonic power and frequency and process time) on sonochemical degradation was investigated. Conversion was found to increase with increase in initial concentration, temperature, power level and frequency. Both horntype and tank-type sonicators were used, at various power levels (250W, 400W and 500W) for frequencies ranging from 20 kHz - 1000 kHz. A 'Process Intensification' parameter PI, was defined to quantify the enhancement of the degradation reaction by ultrasound when compared to control (i.e., without ultrasound). The present work clearly demonstrates that a high-frequency ultrasonic bath can be used to achieve higher process throughput and energy efficiency at a larger scale of operation.
Abstract: Based on the combined shape feature and texture
feature, a fast object detection method with rotation invariant features
is proposed in this paper. A quick template matching scheme based
online learning designed for online applications is also introduced in
this paper. The experimental results have shown that the proposed
approach has the features of lower computation complexity and
higher detection rate, while keeping almost the same performance
compared to the HOG-based method, and can be more suitable for
run time applications.
Abstract: This paper describes topic of computer simulation with regard to the ground movement above an underground mine. Simulation made with software package ADINA for nonlinear elastic-plastic analysis with finite elements method. The one of representative profiles from Mine 'Stara Jama' in Zenica has been investigated. A collection and selection of both geo-mechanical data and geometric parameters of the mine was necessary for performing these simulations. Results of estimation have been compared with measured values (vertical displacement of surface), and then simulation performed with assumed dynamic and dimensions of excavation, over a period of time. Results are presented with bitmaps and charts.
Abstract: To produce sugar and ethanol, sugarcane processing
generates several agricultural residues, being straw and bagasse is
considered as the main among them. And what to do with this
residues has been subject of many studies and experiences in an
industry that, in recent years, highlighted by the ability to transform
waste into valuable products such as electric power. Cellulose is the
main component of these materials. It is the most common organic
polymer and represents about 1.5 x 1012 tons of total production of
biomass per year and is considered an almost inexhaustible source of
raw material. Pretreatment with mineral acids is one of the most
widely used as stage of cellulose extraction from lignocellulosic
materials for solubilizing most of the hemicellulose content. This
study had as goal to find the best reaction time of sugarcane bagasse
pretreatment with sulfuric acid in order to minimize the losses of
cellulose concomitantly with the highest possible removal of
hemicellulose and lignin. It was found that the best time for this
reaction was 40 minutes, in which it was reached a loss of
hemicelluloses around 70% and lignin and cellulose, around 15%.
Over this time, it was verified that the cellulose loss increased and
there was no loss of lignin and hemicellulose.
Abstract: In this work, we study elliptic divisibility sequences
over finite fields. Morgan Ward in [14], [15] gave arithmetic theory
of elliptic divisibility sequences and formulas for elliptic divisibility
sequences with rank two over finite field Fp. We study elliptic
divisibility sequences with rank three, four and five over a finite field
Fp, where p > 3 is a prime and give general terms of these sequences
and then we determine elliptic and singular curves associated with
these sequences.
Abstract: A two-dimensional thin-walled capsule of a flexible
semi-permeable membrane is adhered onto a rigid planar substrate
under adhesive forces (derived from a potential function) in the
presence of osmosis across the membrane. The capsule is immersed
in a hypotonic and diluted binary solution of a non-electrolyte
solute. The Stokes flow problem is solved by the immersed interface
method (IIM) with equal viscosities for the enclosed and
surrounding fluid of the capsule. The numerical results obtained are
verified against two simplified theoretical solutions and the
agreements are good. The osmotic inflation of the adhered capsule is
studied as a function of the solute concentration field, hydraulic
conductivity, and the initial capsule shape. Our findings indicate that
the contact length shrinks in dimension as capsule inflates in the
hypotonic medium, and the equilibrium contact length does not
depend on the hydraulic conductivity of the membrane and the
initial shape of the capsule.
Abstract: One of the efficient factors in comprehensive
development of an area is to provide water sources and on the other
hand the appropriate management of them. Population growth and
nourishment security for such a population necessitate the
achievement of constant development besides the reforming of
traditional management in order to increase the profit of sources; In
this case, the constant exploitation of sources for the next generations
will be considered in this program. The achievement of this
development without the consideration and possibility of water
development will be too difficult. Zayanderood basin with 41500
areas in square kilometers contains 7 sub-basins and 20 units of
hydrologic. In this basin area, from the entire environment
descending, just a small part will enter into the river currents and the
rest will be out of efficient usage by various ways. The most
important surface current of this basin is Zayanderood River with
403 kilometers length which is originated from east slopes of Zagros
mount and after draining of this basin area it will enter into
Gaavkhooni pond. The existence of various sources and
consumptions of water in Zayanderood basin, water transfer of the
other basin areas into this basin, of course the contradiction between
the upper and lower beneficiaries, the existence of worthwhile
natural ecosystems such as Gaavkhooni swamp in this basin area and
finally, the drought condition and lack of water in this area all
necessitate the existence of comprehensive management of water
sources in this central basin area of Iran as this method is a kind of
management which considers the development and the management
of water sources as an equilibrant way to increase the economical
and social benefits. In this study, it is tried to survey the network of
surface water sources of basin in upper and lower sections; at the
most, according to the difficulties and deficiencies of an efficient
management of water sources in this basin area, besides the
difficulties of water draining and the destructive phenomenon of
flood-water, the appropriate guidelines according to the region
conditions are presented in order to prevent the deviation of water in
upper sections and development of regions in lower sections of
Zayanderood dam.
Abstract: With the fast progression of data exchange in electronic way, information security is becoming more important in data storage and transmission. Because of widely using images in industrial process, it is important to protect the confidential image data from unauthorized access. In this paper, we analyzed current image encryption algorithms and compression is added for two of them (Mirror-like image encryption and Visual Cryptography). Implementations of these two algorithms have been realized for experimental purposes. The results of analysis are given in this paper.
Abstract: The main objective of this work is to compare the
quality of service of the bus companies operating in the city of Rio
Branco, located in the state of Acre with the quality of service of the
bus companies operating in the city of Campos, situated in the state
of Rio de Janeiro, both cities in Brazil. This comparison, based on the
opinion of the bus users, will determine their degree of satisfaction
with the service available in both cities. The outcome of this
evaluation shows the users unhappy with the quality of the service
provided by the bus companies operating in both cities and the need
to identify alternative solutions that may minimize the consequences
caused by the main problems detected in this work. With these
alternatives available, the bus companies will be able to better
understand the needs of their customers in terms of manpower,
service cost, time schedule, etc.
Abstract: Computational simulation of steam flow and heat transfer in power plant condensers on the basis of the threedimensional mathematical model for the flow through porous media is presented. In order to solve the mathematical model of steam flow and heat transfer in power plant condensers, the Streamline Upwind Petrov-Galerkin finite element method is applied. By comparison of the results of simulation with experimental results about an experimental condenser, it is confirmed that SUPG finite element method can be successfully applied for solving the three-dimensional mathematical model of steam flow and heat transfer in power plant condensers.
Abstract: Iris pattern is an important biological feature of human body; it becomes very hot topic in both research and practical applications. In this paper, an algorithm is proposed for iris recognition and a simple, efficient and fast method is introduced to extract a set of discriminatory features using first order gradient operator applied on grayscale images. The gradient based features are robust, up to certain extents, against the variations may occur in contrast or brightness of iris image samples; the variations are mostly occur due lightening differences and camera changes. At first, the iris region is located, after that it is remapped to a rectangular area of size 360x60 pixels. Also, a new method is proposed for detecting eyelash and eyelid points; it depends on making image statistical analysis, to mark the eyelash and eyelid as a noise points. In order to cover the features localization (variation), the rectangular iris image is partitioned into N overlapped sub-images (blocks); then from each block a set of different average directional gradient densities values is calculated to be used as texture features vector. The applied gradient operators are taken along the horizontal, vertical and diagonal directions. The low order norms of gradient components were used to establish the feature vector. Euclidean distance based classifier was used as a matching metric for determining the degree of similarity between the features vector extracted from the tested iris image and template features vectors stored in the database. Experimental tests were performed using 2639 iris images from CASIA V4-Interival database, the attained recognition accuracy has reached up to 99.92%.
Abstract: In order to apply partially filled steel grid composite deck as the horizontal supporting structure of various kinds of infrastructures, the variation of its flexural strength according to design parameters such as cross and longitudinal bars constituting the steel grid and the type of shear connection is evaluated and compared experimentally. The result shows that the design sensitivity of the deck to the spacing of the cross bars is insignificant in the case of structure with low risk of punching failure or without load distribution problem. By means of shear connection composed by transverse rebar and longitudinal bar without additional shear stud bolts, the complete interaction between steel grid and concrete slab is able to be achieved and the composite deck can develop its bending resistance capacity.
Abstract: It has been shown that a load discontinuity at the end of
an impulse will result in an extra impulse and hence an extra amplitude
distortion if a step-by-step integration method is employed to yield the
shock response. In order to overcome this difficulty, three remedies
are proposed to reduce the extra amplitude distortion. The first remedy
is to solve the momentum equation of motion instead of the force
equation of motion in the step-by-step solution of the shock response,
where an external momentum is used in the solution of the momentum
equation of motion. Since the external momentum is a resultant of the
time integration of external force, the problem of load discontinuity
will automatically disappear. The second remedy is to perform a single
small time step immediately upon termination of the applied impulse
while the other time steps can still be conducted by using the time step
determined from general considerations. This is because that the extra
impulse caused by a load discontinuity at the end of an impulse is
almost linearly proportional to the step size. Finally, the third remedy
is to use the average value of the two different values at the integration
point of the load discontinuity to replace the use of one of them for
loading input. The basic motivation of this remedy originates from the
concept of no loading input error associated with the integration point
of load discontinuity. The feasibility of the three remedies are
analytically explained and numerically illustrated.
Abstract: CO2 miscible displacement is not feasible in many oil fields due to high reservoir temperature as higher pressure is required to achieve miscibility. The miscibility pressure is far higher than the formation fracture pressure making it impossible to have CO2 miscible displacement. However, by using oleophilic chemicals, minimum miscibility pressure (MMP) could be lowered. The main objective of this research is to find the best oleophilic chemical in MMP reduction using slim-tube test and Vanishing Interfacial Tension (VIT) The chemicals are selected based on the characteristics that it must be oil soluble, low water solubility, have 4 – 8 carbons, semi polar, economical, and safe for human operation. The families of chemicals chosen are carboxylic acid, alcohol, and ketone. The whole experiment would be conducted at 100°C and the best chemical is said to be effective when it is able to lower CO2-crude oil MMP the most. Findings of this research would have great impact to the oil and gas industry in reduction of operation cost for CO2EOR which is applicable to both onshore and offshore operation.
Abstract: Wind is among the potential energy resources which
can be harnessed to generate wind energy for conversion into
electrical power. Due to the variability of wind speed with time and
height, it becomes difficult to predict the generated wind energy more
optimally. In this paper, an attempt is made to establish a
probabilistic model fitting the wind speed data recorded at
Makambako site in Tanzania. Wind speeds and direction were
respectively measured using anemometer (type AN1) and wind Vane
(type WD1) both supplied by Delta-T-Devices at a measurement
height of 2 m. Wind speeds were then extrapolated for the height of
10 m using power law equation with an exponent of 0.47. Data were
analysed using MINITAB statistical software to show the variability
of wind speeds with time and height, and to determine the underlying
probability model of the extrapolated wind speed data. The results
show that wind speeds at Makambako site vary cyclically over time;
and they conform to the Weibull probability distribution. From these
results, Weibull probability density function can be used to predict
the wind energy.