Abstract: Since 2004, we have been developing an in-situ storage image sensor (ISIS) that captures more than 100 consecutive images at a frame rate of 10 Mfps with ultra-high sensitivity as well as the video camera for use with this ISIS. Currently, basic research is continuing in an attempt to increase the frame rate up to 100 Mfps and above. In order to suppress electro-magnetic noise at such high frequency, a digital-noiseless imaging transfer scheme has been developed utilizing solely sinusoidal driving voltages. This paper presents highly efficient-yet-accurate expressions to estimate attenuation as well as phase delay of driving voltages through RC networks of an ultra-high-speed image sensor. Elmore metric for a fundamental RC chain is employed as the first-order approximation. By application of dimensional analysis to SPICE data, we found a simple expression that significantly improves the accuracy of the approximation. Similarly, another simple closed-form model to estimate phase delay through fundamental RC networks is also obtained. Estimation error of both expressions is much less than previous works, only less 2% for most of the cases . The framework of this analysis can be extended to address similar issues of other VLSI structures.
Abstract: Numerical design optimization is a powerful tool that
can be used by engineers during any stage of the design process.
There are many different applications for structural optimization. A
specific application that will be discussed in the following paper is
experimental data matching. Data obtained through tests on a physical
structure will be matched with data from a numerical model of that
same structure. The data of interest will be the dynamic characteristics
of an antenna structure focusing on the mode shapes and modal
frequencies. The structure used was a scaled and simplified model of
the Karoo Array Telescope-7 (KAT-7) antenna structure.
This kind of data matching is a complex and difficult task. This
paper discusses how optimization can assist an engineer during the
process of correlating a finite element model with vibration test data.
Abstract: In this paper after reviewing some previous studies, in
order to optimize the above knee prosthesis, beside the inertial
properties a new controlling parameter is informed. This controlling
parameter makes the prosthesis able to act as a multi behavior system
when the amputee is opposing to different environments. This active
prosthesis with the new controlling parameter can simplify the
control of prosthesis and reduce the rate of energy consumption in
comparison to recently presented similar prosthesis “Agonistantagonist
active knee prosthesis".
In this paper three models are generated, a passive, an active, and
an optimized active prosthesis. Second order Taylor series is the
numerical method in solution of the models equations and the
optimization procedure is genetic algorithm.
Modeling the prosthesis which comprises this new controlling
parameter (SEP) during the swing phase represents acceptable results
in comparison to natural behavior of shank. Reported results in this
paper represent 3.3 degrees as the maximum deviation of models
shank angle from the natural pattern. The natural gait pattern belongs
to walking at the speed of 81 m/min.
Abstract: In the present study, we aimed to design the
intrauterine and extrauterine exposure to 1800 MHz GSM-like RF
radiation and investigate its possible bio-effects on infant female
rabbits. Totally thirty-six New Zealand White female rabbits, onemonth
old, were randomly divided into four groups which are
composed of 9 rabbits; i. Group I [Intrauterine (IU) exposure(-);
Extrauterine (EU) exposure (-)], Group II [IU exposure (-); EU
exposure (+)], Group III [IU exposure(+);EU exposure(-)], Group IV
[IU exposure (+);EU exposure(+)]. The master regulatory enzymes
activities of pentose phosphate pathway (glucose-6-phosphate
dehydrogenase, G-6PD; 6-phosphogluconate dehydrogenase, 6-
PGDH) and glutathione-dependent metabolism (glutathione
peroxidase, GSH-Px; glutathione reductase, GR; glutathione Stransferase,
GST, thioredoxin reductase, TRx) were analyzed in liver
tissues of young female rabbits. Decreased G-6PD, 6-PGD, GSH-Px,
GR activities were found in Group III compared to Group I (p
Abstract: This paper discusses aspects of re-design of loadshedding
schemes with respect to actual developments in the Kosovo
power system. Load-shedding is a type of emergency control that is
designed to ensure system stability by reducing power system load to
match the power generation supply. This paper presents a new
adaptive load-shedding scheme that provides emergency protection
against excess frequency decline, in cases when the Kosovo power
system might be disconnected from the regional transmission
network. The proposed load-shedding scheme uses the local
frequency rate information to adapt the load-shedding pattern to suit
the size and location of the occurring disturbance. The proposed
scheme is tested in a software simulation on a large scale PSS/E
model which represents nine power system areas of Southeast Europe
including the Kosovo power system.
Abstract: The supply chains (SCs) have to appeal to new management paradigms to improve their ability to respond rapidly and cost effectively to unpredictable changes in markets and increasing levels of environmental turbulence, both in terms of volume and variety. In this highly demanded context, the Agile paradigm provides the capabilities to SC quickly adapt to changes in the market requirements. The purpose of this paper is to suggest an Agile Index to assess the agility of the automotive companies and corresponding SCs. The proposed integrated assessment model incorporates Agile practices weighted according to their importance to the automotive SC competitiveness and obtained from the Delphi technique.
Abstract: In this note, a theoretical model for analyzing of
normal penetration of the ogive – nose projectile into metallic targets
is presented .The failure is assumed to be asymmetry petalling and
the analysis is performed by using the energy balance and work done
.The work done consist of the work required for plastic deformation
Wp, the work for transferring the matter to new position Wd and the
work for bending of the petals Wb. In several studies, it has been
shown that we can neglect the loss of energy by temperature.
In this present study, in first, by assuming the crater formation
after perforation, the value of work done is calculated during the
normal penetration of conical projectiles into thin metallic targets.
Then the value of residual velocity and ballistic limit of the projectile
is predicated by using the energy balance. In final, theoretical and
experimental results is compared.
Abstract: The balancing numbers are natural numbers n satisfying
the Diophantine equation 1 + 2 + 3 + · · · + (n - 1) = (n + 1) +
(n + 2) + · · · + (n + r); r is the balancer corresponding to the
balancing number n.The nth balancing number is denoted by Bn
and the sequence {Bn}1
n=1 satisfies the recurrence relation Bn+1 =
6Bn-Bn-1. The balancing numbers posses some curious properties,
some like Fibonacci numbers and some others are more interesting.
This paper is a study of recurrent sequence {xn}1
n=1 satisfying the
recurrence relation xn+1 = Axn - Bxn-1 and possessing some
curious properties like the balancing numbers.
Abstract: A multiphase harmonic load flow algorithm is developed based on backward/forward sweep to examine the effects of various factors on the neutral to earth voltage (NEV), including unsymmetrical system configuration, load unbalance and harmonic injection. The proposed algorithm composes fundamental frequency and harmonic frequencies power flows. The algorithm and the associated models are tested on IEEE 13 bus system. The magnitude of NEV is investigated under various conditions of the number of grounding rods per feeder lengths, the grounding rods resistance and the grounding resistance of the in feeding source. Additionally, the harmonic injection of nonlinear loads has been considered and its influences on NEV under different conditions are shown.
Abstract: An investigation of noise in a micro stepping motor is
considered to study in this article. Because of the trend towards higher
precision and more and more small 3C (including Computer,
Communication and Consumer Electronics) products, the micro
stepping motor is frequently used to drive the micro system or the
other 3C products. Unfortunately, noise in a micro stepped motor is
too large to accept by the customs. To depress the noise of a micro
stepped motor, the dynamic characteristics in this system must be
studied. In this article, a Visual Basic (VB) computer program speed
controlled micro stepped motor in a digital camera is investigated.
Karman KD2300-2S non-contract eddy current displacement sensor,
probe microphone, and HP 35670A analyzer are employed to analyze
the dynamic characteristics of vibration and noise in a motor. The
vibration and noise measurement of different type of bearings and
different treatment of coils are compared. The rotating components,
bearings, coil, etc. of the motor play the important roles in producing
vibration and noise. It is found that the noise will be depressed about
3~4 dB and 6~7 dB, when substitutes the copper bearing with plastic
one and coats the motor coil with paraffin wax, respectively.
Abstract: Transpedicular screw fixation in spinal fractures,
degenerative changes, or deformities is a well-established procedure.
However, important rate of fixation failure due to screw bending,
loosening, or pullout are still reported particularly in weak bone stock
in osteoporosis. To overcome the problem, mechanism of failure has
to be fully investigated in vitro. Post-mortem human subjects are less
accessible and animal cadavers comprise limitations due to different
geometry and mechanical properties. Therefore, the development of a
synthetic model mimicking the realistic human vertebra is highly
demanded. A bone surrogate, composed of Polyurethane (PU) foam
analogous to cancellous bone porous structure, was tested for 3
different densities in this study. The mechanical properties were
investigated under uniaxial compression test by minimizing the end
artifacts on specimens. The results indicated that PU foam of 0.32
g.cm-3 density has comparable mechanical properties to human
cancellous bone in terms of young-s modulus and yield strength.
Therefore, the obtained information can be considered as primary
step for developing a realistic cancellous bone of human vertebral
body. Further evaluations are also recommended for other density
groups.
Abstract: The paper presents an analytical solution for dispersion
of a solute in the peristaltic motion of a couple stress fluid
through a porous medium with slip condition in the presence of both
homogeneous and heterogeneous chemical reactions. The average
effective dispersion coefficient has been found using Taylor-s limiting
condition and long wavelength approximation. The effects of various
relevant parameters on the average coefficient of dispersion have been
studied. The average effective dispersion coefficient tends to increase
with permeability parameter but tends to decrease with homogeneous
chemical reaction rate parameter, couple stress parameter, slip parameter
and heterogeneous reaction rate parameter.
Abstract: Two commercial proteases from Bacillus
licheniformis (Alcalase 2.4 L FG and Alcalase 2.5 L, Type DX) were
screened for the production of Z-Ala-Phe-NH2 in batch reaction.
Alcalase 2.4 L FG was the most efficient enzyme for the C-terminal
amidation of Z-Ala-Phe-OMe using ammonium carbamate as
ammonium source. Immobilization of protease has been achieved by
the sol-gel method, using dimethyldimethoxysilane (DMDMOS) and
tetramethoxysilane (TMOS) as precursors (unpublished results). In
batch production, about 95% of Z-Ala-Phe-NH2 was obtained at
30°C after 24 hours of incubation. Reproducibility of different
batches of commercial Alcalase 2.4 L FG preparations was also
investigated by evaluating the amidation activity and the entrapment
yields in the case of immobilization. A packed-bed reactor (0.68 cm
ID, 15.0 cm long) was operated successfully for the continuous
synthesis of peptide amides. The immobilized enzyme retained the
initial activity over 10 cycles of repeated use in continuous reactor at
ambient temperature. At 0.75 mL/min flow rate of the substrate
mixture, the total conversion of Z-Ala-Phe-OMe was achieved after 5
hours of substrate recycling. The product contained about 90%
peptide amide and 10% hydrolysis byproduct.
Abstract: In this paper is reported an analysis about the outdoor air pollution of the urban centre of the city of Messina. The variations of the most critical pollutants concentrations (PM10, O3, CO, C6H6) and their trends respect of climatic parameters and vehicular traffic have been studied. Linear regressions have been effectuated for representing the relations among the pollutants; the differences between pollutants concentrations on weekend/weekday were also analyzed. In order to evaluate air pollution and its effects on human health, a method for calculating a pollution index was implemented and applied in the urban centre of the city. This index is based on the weighted mean of the most detrimental air pollutants concentrations respect of their limit values for protection of human health. The analyzed data of the polluting substances were collected by the Assessorship of the Environment of the Regional Province of Messina in the year 2004. A statistical analysis of the air quality index trends is also reported.
Abstract: In this paper we describe the design and implementation of a parallel algorithm for data assimilation with ensemble Kalman filter (EnKF) for oil reservoir history matching problem. The use of large number of observations from time-lapse seismic leads to a large turnaround time for the analysis step, in addition to the time consuming simulations of the realizations. For efficient parallelization it is important to consider parallel computation at the analysis step. Our experiments show that parallelization of the analysis step in addition to the forecast step has good scalability, exploiting the same set of resources with some additional efforts.
Abstract: The stilling basins are commonly used to dissipate the
energy and protect the downstream floor from erosion. The aim of
the present experimental work is to improve the roughened stilling
basin using T-shape roughness instead of the regular cubic one and
design this new shape. As a result of the present work the best
intensity and the best roughness length are identified. Also, it is
found that the T-shape roughness save materials and reduce the jump
length compared to the cubic one. Sensitivity analysis was performed
and it was noticed that the change in the length of jump is more
sensitive to the change in roughness length than the change in
intensity.
Abstract: It has become crucial over the years for nations to
improve their credit scoring methods and techniques in light of the
increasing volatility of the global economy. Statistical methods or
tools have been the favoured means for this; however artificial
intelligence or soft computing based techniques are becoming
increasingly preferred due to their proficient and precise nature and
relative simplicity. This work presents a comparison between Support
Vector Machines and Artificial Neural Networks two popular soft
computing models when applied to credit scoring. Amidst the
different criteria-s that can be used for comparisons; accuracy,
computational complexity and processing times are the selected
criteria used to evaluate both models. Furthermore the German credit
scoring dataset which is a real world dataset is used to train and test
both developed models. Experimental results obtained from our study
suggest that although both soft computing models could be used with
a high degree of accuracy, Artificial Neural Networks deliver better
results than Support Vector Machines.
Abstract: For several high speed networks, providing resilience against failures is an essential requirement. The main feature for designing next generation optical networks is protecting and restoring high capacity WDM networks from the failures. Quick detection, identification and restoration make networks more strong and consistent even though the failures cannot be avoided. Hence, it is necessary to develop fast, efficient and dependable fault localization or detection mechanisms. In this paper we propose a new fault localization algorithm for WDM networks which can identify the location of a failure on a failed lightpath. Our algorithm detects the failed connection and then attempts to reroute data stream through an alternate path. In addition to this, we develop an algorithm to analyze the information of the alarms generated by the components of an optical network, in the presence of a fault. It uses the alarm correlation in order to reduce the list of suspected components shown to the network operators. By our simulation results, we show that our proposed algorithms achieve less blocking probability and delay while getting higher throughput.
Abstract: Changing in consumers lifestyles and food
consumption patterns provide a great opportunity in developing the
functional food sector in Malaysia. There is only a little knowledge
about whether Malaysian consumers are aware of functional food and
if so what image consumers have of this product. The objective of
this research is to determine the extent to which selected socioeconomic
characteristics and attitudes influence consumers-
awareness of functional food. A survey was conducted in the Klang
Valley, Malaysia where 439 respondents were interviewed using a
structured questionnaire. The result shows that most respondents
have a positive attitude towards functional food. For the binary
logistic estimation, the results indicate that age, income and other
factors such as concern about food safety, subscribing to cooking or
health magazines, being a vegetarian and consumers who have been
involved in a food production company significantly influence
Malaysian consumers- awareness towards functional food.
Abstract: In this work, the condensation fraction and transition
temperature of neutral many bosonic system are studied within the
static fluctuation approximation (SFA). The effect of the potential
parameters such as the strength and range on the condensate fraction
was investigated. A model potential consisting of a repulsive step
potential and an attractive potential well was used. As the potential
strength or the core radius of the repulsive part increases, the
condensation fraction is found to be decreased at the same
temperature. Also, as the potential depth or the range of the attractive
part increases, the condensation fraction is found to be increased. The
transition temperature is decreased as the potential strength or the
core radius of the repulsive part increases, and it increases as the
potential depth or the range of the attractive part increases.