Abstract: The quest for alternatefuels for a CI engine has
become all the more imperative considering its importance in the
economy of a nation and from the standpoint of preserving the environment. Reported in this paper are the combustion performance and P-θ characteristics of a CI engine operating on B20 biodiesel fuel derived from Jatropha oil.Itis observed that the twin effect of advancing the injection timing and increasing the injector opening pressure (IOP) up to 220 barhas resulted in minimum brake specific
energy consumption and higherpeak pressure. It is also observed that
the crank angle of occurrence of peak pressure progressestowards top
dead center (TDC) as the timing is advanced and IOP is increased.
Abstract: In this study, an ablation, mechanical and thermal properties of a rocket motor insulation from phenolic/ fiber matrix composites forming a laminate with different fiber between fiberglass and locally available synthetic fibers. The phenolic/ fiber matrix composites was mechanics and thermal properties by means of tensile strength, ablation, TGA and DSC. The design of thermal insulation involves several factors.Determined the mechanical properties according to MIL-I-24768: Density >1.3 g/cm3, Tensile strength >103 MPa and Ablation
Abstract: In research on natural ventilation, and passive cooling
with forced convection, is essential to know how heat flows in a solid
object and the pattern of temperature distribution on their surfaces,
and eventually how air flows through and convects heat from the
surfaces of steel under roof. This paper presents some results from
running the computational fluid dynamic program (CFD) by
comparison between natural ventilation and forced convection within
roof attic that is received directly from solar radiation. The CFD
program for modeling air flow inside roof attic has been modified to
allow as two cases. First case, the analysis under natural ventilation,
is closed area in roof attic and second case, the analysis under forced
convection, is opened area in roof attic. These extend of all cases to
available predictions of variations such as temperature, pressure, and
mass flow rate distributions in each case within roof attic. The
comparison shows that this CFD program is an effective model for
predicting air flow of temperature and heat transfer coefficient
distribution within roof attic. The result shows that forced convection
can help to reduce heat transfer through roof attic and an around area
of steel core has temperature inner zone lower than natural
ventilation type. The different temperature on the steel core of roof
attic of two cases was 10-15 oK.
Abstract: Coal will continue to be the predominant source of
global energy for coming several decades. The huge generation of fly
ash (FA) from combustion of coal in thermal power plants (TPPs) is
apprehended to pose the concerns of its disposal and utilization. FA
application based on its typical characteristics as soil ameliorant for
agriculture and forestry is the potential area, and hence the global
attempt. The inferences drawn suffer from the variations of ash
characteristics, soil types, and agro-climatic conditions; thereby
correlating the effects of ash between various plant species and soil
types is difficult. Indian FAs have low bulk density, high water
holding capacity and porosity, rich silt-sized particles, alkaline
nature, negligible solubility, and reasonable plant nutrients. Findings
of the demonstrations trials for more than two decades from lab/pot
to field scale long-term experiments are developed as FA soil
amendment technology (FASAT) by Central Institute of Mining and
Fuel Research (CIMFR), Dhanbad. Performance of different crops
and plant species in cultivable and problematic soils, are
encouraging, eco-friendly, and being adopted by the farmers. FA
application includes ash alone and in combination with
inorganic/organic amendments; combination treatments including
bio-solids perform better than FA alone. Optimum dose being up to
100 t/ha for cultivable land and up to/ or above 200 t/ha of FA for
waste/degraded land/mine refuse, depending on the characteristics of
ash and soil. The elemental toxicity in Indian FA is usually not of
much concern owing to alkaline ashes, oxide forms of elements, and
elemental concentration within the threshold limits for soil
application. Combating toxicity, if any, is possible through
combination treatments with organic materials and phytoremediation.
Government initiatives through extension programme
involving farmers and ash generating organizations need to be
accelerated
Abstract: Fabrication and efficiency enhancement of non-mercury, high efficiency and green field emission lamps using carbon nano-materials such as carbon nanotubes as cathode field emitters was studied. Phosphor was coated on the ITO glass or metal substrates as the anode. The luminescence efficiency enhancement was carried out by upgrading the uniform of the emitters, improving electron and thermal conductivity of the phosphor and the optimization of the design of different cathode/anode configurations. After evaluation of the aforementioned parameters, the luminescence efficiency of the field emission lamps was raised.
Abstract: In recent years, environment regulation forcing
manufactures to consider recovery activity of end-of- life products
and/or return products for refurbishing, recycling,
remanufacturing/repair and disposal in supply chain management. In
this paper, a mathematical model is formulated for single product
production-inventory system considering remanufacturing/reuse of
return products and rate of return products follows a demand like
function, dependent on purchasing price and acceptance quality level.
It is useful in decision making to determine whether to go for
remanufacturing or disposal of returned products along with newly
produced products to satisfy a stationary demand. In addition, a
modified genetic algorithm approach is proposed, inspired by particle
swarm optimization method. Numerical analysis of the case study is
carried out to validate the model.
Abstract: Fermented beverages have high expression in the
market for beverages in general, is increasingly valued in situations
where the characteristic aroma and flavor of the material that gave
rise to them are kept after processing. This study aimed to develop a
distilled beverage from passion fruit, and assess, by sensory tests and
chromatographic profile, the influence of different treatments (FM1-
spirit with pulp addiction and FM2 – spirit with bigger ratio of pulp
in must) in the setting of volatiles in the fruit drink, and performing
chemical characterization taking into account the main parameters of
quality established by the legislation. The chromatograms and the
first sensorial tests had indicated that sample FM1 possess better
characteristics of aroma, as much of how much quantitative the
qualitative point of view. However, it analyzes it sensorial end
(preference test) disclosed the biggest preference of the cloth provers
for sample FM2-2 (note 7.93), being the attributes of decisive color
and flavor in this reply, confirmed for the observed values lowest of
fixed and total acidity in the samples of treatment FM2.
Abstract: In the past years a lot of effort has been made in the
field of face detection. The human face contains important features
that can be used by vision-based automated systems in order to
identify and recognize individuals. Face location, the primary step of
the vision-based automated systems, finds the face area in the input
image. An accurate location of the face is still a challenging task.
Viola-Jones framework has been widely used by researchers in order
to detect the location of faces and objects in a given image. Face
detection classifiers are shared by public communities, such as
OpenCV. An evaluation of these classifiers will help researchers to
choose the best classifier for their particular need. This work focuses
of the evaluation of face detection classifiers minding facial
landmarks.
Abstract: Power-line networks are widely used today for broadband data transmission. However, due to multipaths within the broadband power line communication (BPLC) systems owing to stochastic changes in the network load impedances, branches, etc., network or channel capacity performances are affected. This paper attempts to investigate the performance of typical medium voltage channels that uses Orthogonal Frequency Division Multiplexing (OFDM) techniques with Quadrature Amplitude Modulation (QAM) sub carriers. It has been observed that when the load impedances are different from line characteristic impedance channel performance decreases. Also as the number of branches in the link between the transmitter and receiver increases a loss of 4dB/branch is found in the signal to noise ratio (SNR). The information presented in the paper could be useful for an appropriate design of the BPLC systems.
Abstract: In today-s competitive environment, the security concerns have grown tremendously. In the modern world, possession is known to be 9/10-ths of the law. Hence, it is imperative for one to be able to safeguard one-s property from worldly harms such as thefts, destruction of property, people with malicious intent etc. Due to the advent of technology in the modern world, the methodologies used by thieves and robbers for stealing have been improving exponentially. Therefore, it is necessary for the surveillance techniques to also improve with the changing world. With the improvement in mass media and various forms of communication, it is now possible to monitor and control the environment to the advantage of the owners of the property. The latest technologies used in the fight against thefts and destruction are the video surveillance and monitoring. By using the technologies, it is possible to monitor and capture every inch and second of the area in interest. However, so far the technologies used are passive in nature, i.e., the monitoring systems only help in detecting the crime but do not actively participate in stopping or curbing the crime while it takes place. Therefore, we have developed a methodology to detect the motion in a video stream environment and this is an idea to ensure that the monitoring systems not only actively participate in stopping the crime, but do so while the crime is taking place. Hence, a system is used to detect any motion in a live streaming video and once motion has been detected in the live stream, the software will activate a warning system and capture the live streaming video.
Abstract: The paper proposes an approach for design of modular
systems based on original technique for modeling and formulation of
combinatorial optimization problems. The proposed approach is
described on the example of personal computer configuration design.
It takes into account the existing compatibility restrictions between
the modules and can be extended and modified to reflect different
functional and users- requirements. The developed design modeling
technique is used to formulate single objective nonlinear mixedinteger
optimization tasks. The practical applicability of the
developed approach is numerically tested on the basis of real modules
data. Solutions of the formulated optimization tasks define the
optimal configuration of the system that satisfies all compatibility
restrictions and user requirements.
Abstract: The effect of cassava root ensiled with cassava top or
legumes on voluntary feed intake and milk production were
determined in 12 dairy cows using a 4×3 change-over design.
Experimental period were 30 days long and consisted of 14 days of
adaptation. Silage was prepared from cassava root mixed with
cassava top or legumes at ratio 60:40. Cows were allotted at random
to receive ad libitum one of four rations: T1) control, T2) cassava
root +cassava top-silages, T3) cassava root +hamata - silages and T4)
cassava root +Thapra stylo-silages.
The dry matter intake (BW0.75) was higher (P< 0.05) in cow fed
with silages diets compared with T1. However, the intake of T2 was
higher among treatments. Milk production was lowest in cow fed
with T1. Among silages based diets, milk production was not
significantly different but 4%FCM was higher in cow fed T2. Milk
compositions were not affected by feeding diets.
It is concluded that feeding cassava root ensiled with its leaves as
a supplement increased dry matter intake and significantly improved
4%FCM. The combination of cassava root and legume silages did not
improve the feed intake but did increase the milk production.
Abstract: In this study the effect of incorporation of recycled
glass-fibre reinforced polymer (GFRP) waste materials, obtained by
means of milling processes, on mechanical behaviour of polyester
polymer mortars was assessed. For this purpose, different contents of
recycled GFRP waste powder and fibres, with distinct size gradings,
were incorporated into polyester based mortars as sand aggregates
and filler replacements. Flexural and compressive loading capacities
were evaluated and found better than unmodified polymer mortars.
GFRP modified polyester based mortars also show a less brittle
behaviour, with retention of some loading capacity after peak load.
Obtained results highlight the high potential of recycled GFRP waste
materials as efficient and sustainable reinforcement and admixture for
polymer concrete and mortars composites, constituting an emergent
waste management solution.
Abstract: In the present communication, we have proposed
some new generalized measure of fuzzy entropy based upon real
parameters, discussed their and desirable properties, and presented
these measures graphically. An important property, that is,
monotonicity of the proposed measures has also been studied.
Abstract: This article presents new current-mode oscillator circuits using CDTAs which is designed from block diagram. The proposed circuits consist of two CDTAs and two grounded capacitors. The condition of oscillation and the frequency of oscillation can be adjusted by electronic method. The circuits have high output impedance and use only grounded capacitors without any external resistor which is very appropriate to future development into an integrated circuit. The results of PSPICE simulation program are corresponding to the theoretical analysis.
Abstract: Data on 657 lactation from 163 Maltese goat,
collected over a 5-year period were analyzed by a mixed model to
estimate the variance components for heritability. The considered
lactation traits were: milk yield (MY) and lactation length (LL). Year,
parity and type of birth (single or twin) were significant sources of
variation for lactation length; on the other hand milk yield was
significantly influenced only by the year. The average MY was
352.34 kg and the average LL was 230 days. Estimates of heritability
were 0.21 and 0.15 for MY and LL respectively. These values
suggest there is low correlation between genotype and phenotype so
it may be difficult to evaluate animals directly on phenotype. So, the
genetic improvement of this breed may be quite slow without the
support of progeny test aimed to select Maltese breeders.
Abstract: This paper presents recent work on the improvement
of the robotics vision based control strategy for underwater pipeline
tracking system. The study focuses on developing image processing
algorithms and a fuzzy inference system for the analysis of the
terrain. The main goal is to implement the supervisory fuzzy learning
control technique to reduce the errors on navigation decision due to
the pipeline occlusion problem. The system developed is capable of
interpreting underwater images containing occluded pipeline, seabed
and other unwanted noise. The algorithm proposed in previous work
does not explore the cooperation between fuzzy controllers,
knowledge and learnt data to improve the outputs for underwater
pipeline tracking. Computer simulations and prototype simulations
demonstrate the effectiveness of this approach. The system accuracy
level has also been discussed.
Abstract: A mathematical model of the surface roughness
has been developed by using response surface methodology
(RSM) in grinding of AISI D2 cold work tool steels. Analysis
of variance (ANOVA) was used to check the validity of the
model. Low and high value for work speed and feed rate are
decided from design of experiment. The influences of all
machining parameters on surface roughness have been
analyzed based on the developed mathematical model. The
developed prediction equation shows that both the feed rate
and work speed are the most important factor that influences
the surface roughness. The surface roughness was found to be
the lowers with the used of low feed rate and low work speed.
Accuracy of the best model was proved with the testing data.
Abstract: With data centers, end-users can realize the pervasiveness of services that will be one day the cornerstone of our lives. However, data centers are often classified as computing systems that consume the most amounts of power. To circumvent such a problem, we propose a self-adaptive weighted sum methodology that jointly optimizes the performance and power consumption of any given data center. Compared to traditional methodologies for multi-objective optimization problems, the proposed self-adaptive weighted sum technique does not rely on a systematical change of weights during the optimization procedure. The proposed technique is compared with the greedy and LR heuristics for large-scale problems, and the optimal solution for small-scale problems implemented in LINDO. the experimental results revealed that the proposed selfadaptive weighted sum technique outperforms both of the heuristics and projects a competitive performance compared to the optimal solution.
Abstract: Bonding has become a routine procedure in several
dental specialties – from prosthodontics to conservative dentistry and
even orthodontics. In many of these fields it is important to be able to
investigate the bonded interfaces to assess their quality. All currently
employed investigative methods are invasive, meaning that samples
are destroyed in the testing procedure and cannot be used again. We
have investigated the interface between human enamel and bonded
ceramic brackets non-invasively, introducing a combination of new
investigative methods – optical coherence tomography (OCT),
fluorescence OCT and confocal microscopy (CM). Brackets were
conventionally bonded on conditioned buccal surfaces of teeth. The
bonding was assessed using these methods. Three dimensional
reconstructions of the detected material defects were developed using
manual and semi-automatic segmentation. The results clearly prove
that OCT, fluorescence OCT and CM are useful in orthodontic
bonding investigations.