Abstract: Stocking density is considered one of the important
factors affecting fish growth. But, information related to impact of
stocking density on growth performance of monosex tilapia population
under the ecological conditions of Gangetic plains in West Bengal,
India is limited. The aim of our study was to compare the growth
potential of monosex tilapia at various stocking densities and to
determine an ideal stocking density for culture of all-male monosex
fish. The males were isolated by examination of genital papilla region
and were stocked separately in 0.01 ha earthen ponds at different
stocking densities (5000, 10000, 15000, 20000, 25000 and 30000
fingerlings/ha). It was found that the highest weight, length, daily
weight gain, growth rate and protein content were observed for the
20000 fish/ha density class. Thus, culture of monosex tilapia at a
density of 20000 fish/ha can be considered ideal for augmented
production of the fish under Indian context.
Abstract: According to the masonry standard the compressive
strength is basically dependent on factors such as the mortar strength
and the relative values of unit and mortar strength. However
interlocking brick has none or less use of mortar. Therefore there is a need to investigate the behavior of masonry walls using interlocking
bricks. In this study a series of tests have been conducted; physical
properties and compressive strength of brick units and masonry walls
were constructed from interlocking bricks and tested under constant
vertical load at different eccentricities. The purpose of the
experimental investigations is to obtain the force displacement curves, analyze the behavior of masonry walls. The results showed
that the brick is categorized as common brick (BS 3921:1985) and severe weathering grade (ASTM C62). The maximum compressive stress of interlocking brick wall is 3.6 N/mm2 and fulfilled the requirement of standard for residential building.
Abstract: An experiment was conducted on the comparative
study of drip and furrow irrigation methods at the farmer-s field in
Umar Kot. The total area under experiment about 4000m2 was
divided into two equal portions. One portion about 40m X 50m was
occupied by drip and the other portion about 40m X 50m by furrow
irrigation method. Soil at the experimental site was clay loam in
texture for 0-60cm depth; average dry bulk density and field capacity
was 1.16g/cm3 and 28.5% respectively. The results reveal that the
drip irrigation method saved 56.4% water and gave 22% more yield
as compared to that of furrow irrigation method. Higher water use
efficiency about 4.87 was obtained in drip irrigation method; whereas
lower water used efficiency about 1.66 was obtained in furrow
irrigation method. The present study suggests farming community to
adopt drip irrigation method instead of old traditional flooding
methods.
Abstract: The purpose of this paper is to conceptualize a futureoriented
human work environment and organizational activity in
deep mines that entails a vision of good and safe workplace. Futureoriented
technological challenges and mental images required for
modern work organization design were appraised. It is argued that an
intelligent-deep-mine covering the entire value chain, including
environmental issues and with work organization that supports good
working and social conditions towards increased human productivity
could be designed. With such intelligent system and work
organization in place, the mining industry could be seen as a place
where cooperation, skills development and gender equality are key
components. By this perspective, both the youth and women might
view mining activity as an attractive job and the work environment
as a safe, and this could go a long way in breaking the unequal
gender balance that exists in most mines today.
Abstract: A research project dealing with the phytoremediation
of a soil polluted by some heavy metals is currently running. The
case study is represented by a mining area in Hamedan province in
the central west part of Iran. The potential of phytoextraction and
phytostabilization of plants was evaluated considering the
concentration of heavy metals in the plant tissues and also the
bioconcentration factor (BCF) and the translocation factor (TF). Also
the several established criteria were applied to define
hyperaccumulator plants in the studied area. Results showed that
none of the collected plant species were suitable for phytoextraction
of Cu, Zn, Fe and Mn, but among the plants, Euphorbia macroclada
was the most efficient in phytostabilization of Cu and Fe, while,
Ziziphora clinopodioides, Cousinia sp. and Chenopodium botrys
were the most suitable for phytostabilization of Zn and Chondrila
juncea and Stipa barbata had the potential for phytostabilization of
Mn. Using the most common criterion, Euphorbia macroclada and
Verbascum speciosum were Fe hyperaccumulator plants. Present
study showed that native plant species growing on contaminated sites
may have the potential for phytoremediation.
Abstract: The effect of SnO2 surface modification by Ag nanoclusters, synthesized by SILD method, on the operating characteristics of thin film gas sensors was studied and models for the promotional role of Ag additives were discussed. It was found that mentioned above approach can be used for improvement both the sensitivity and the rate of response of the SnO2-based gas sensors to CO and H2. At the same time, the presence of the Ag clusters on the surface of SnO2 depressed the sensor response to ozone.
Abstract: The decisions made by admission control algorithms are
based on the availability of network resources viz. bandwidth, energy,
memory buffers, etc., without degrading the Quality-of-Service (QoS)
requirement of applications that are admitted. In this paper, we
present an energy-aware admission control (EAAC) scheme which
provides admission control for flows in an ad hoc network based
on the knowledge of the present and future residual energy of the
intermediate nodes along the routing path. The aim of EAAC is to
quantify the energy that the new flow will consume so that it can
be decided whether the future residual energy of the nodes along
the routing path can satisfy the energy requirement. In other words,
this energy-aware routing admits a new flow iff any node in the
routing path does not run out of its energy during the transmission
of packets. The future residual energy of a node is predicted using
the Multi-layer Neural Network (MNN) model. Simulation results
shows that the proposed scheme increases the network lifetime. Also
the performance of the MNN model is presented.
Abstract: Biological treatment of secondary effluent wastewater
by two combined denitrification/oxic filtration systems packed with
Lock type(denitrification filter) and ceramic ball (oxic filter) has been
studied for 5months. Two phases of operating conditions were carried
out with an influent nitrate and ammonia concentrations varied from
5.8 to 11.7mg/L and 5.4 to 12.4mg/L,respectively.
Denitrification/oxic filter treatment system were operated under an
EBCT (Empty Bed Contact Time) of 4h at system recirculation ratio in
the range from 0 to 300% (Linear Velocity increased 19.5m/d to
78m/d). The system efficiency of denitrification , nitrification over
95% respectively. Total nitrogen and COD removal range from
54.6%(recirculation 0%) to 92.3%(recirculation 300%) and 10% to
62.5%, respectively.
Abstract: We present a method to create special domain
collections from news sites. The method only requires a single
sample article as a seed. No prior corpus statistics are needed and the
method is applicable to multiple languages. We examine various
similarity measures and the creation of document collections for
English and Japanese. The main contributions are as follows. First,
the algorithm can build special domain collections from as little as
one sample document. Second, unlike other algorithms it does not
require a second “general" corpus to compute statistics. Third, in our
testing the algorithm outperformed others in creating collections
made up of highly relevant articles.
Abstract: The production of glass, ceramic materials and many non-ferrous metals (Zn, Cu, Pb, etc.), ferrous metals (pig iron) and others is connected with the use of a considerable number of initial solid raw materials. Before carrying out the basic technological processes (oxidized roasting, melting, agglomeration, baking) it is necessary to mix and homogenize the raw materials that have different chemical and phase content, granulometry and humidity. For this purpose zinc sulfide concentrates differing in origin are studied for their more complete characteristics using chemical, X-ray diffraction analyses, DTA and TGA as well as Mössbauer spectroscopy. The phases established in most concentrates are: β-ZnS, mZnS.nFeS, FeS2, CuFeS2, PbS, SiO2 (α-quartz). With the help of the developed by us a Web-based information system for a continued period of time different mix proportions from zinc concentrates are calculated and used in practice (roasting in fluidized bed reactor), which have to conform to the technological requirements of the zinc hydrometallurgical technological scheme.
Abstract: Energy intensity(energy consumption intensity) is a
global index which computes the required energy for producing a
specific value of goods and services in each country. It is computed
in terms of initial energy supply or final energy consumption. In this
study (research) Divisia method is used to decompose energy
consumption and energy intensity. This method decomposes
consumption and energy intensity to production effects, structural
and net intensity and could be done as time series or two-periodical.
This study analytically investigates consumption changes and energy
intensity on economical sectors of Iran and more specific on road
transportation(rail road and road).Our results show that the
contribution of structural effect (change in economical activities
combination) is very low and the effect of net energy consumption
has the higher contribution in consumption changes and energy
intensity. In other words, the high consumption of energy is due to
Intensity of energy consumption and is not to structural effect of
transportation sector.
Abstract: This paper highlights the importance of integrating social and technical approach (which is so called a “hybrid socio-technical approach") as one innovative and strategic program to support the social development in geodisaster prone area in Indonesia. Such program mainly based on public education and community participation as a partnership program by the University, local government and may also with the private company and/ or local NGO. The indigenous, simple and low cost technology has also been introduced and developed as a part of the hybrid sociotechnical system, in order to ensure the life and environmental protection, with respect to the sustainable human and social development.
Abstract: In this work, we incorporated a quartic bond potential
into a coarse-grained bead-spring model to study lubricant adsorption
on a solid surface as well as depletion instability. The surface tension
density and the number density profiles were examined to verify the
solid-liquid and liquid-vapor interfaces during heat treatment. It was
found that both the liquid-vapor interfacial thickness and the
solid-vapor separation increase with the temperatureT* when T*is
below the phase transition temperature Tc
*. At high temperatures
(T*>Tc
*), the solid-vapor separation decreases gradually as the
temperature increases. In addition, we evaluated the lubricant weight
and bond loss profiles at different temperatures. It was observed that
the lubricant desorption is favored over decomposition and is the main
cause of the lubricant failure at the head disk interface in our
simulations.
Abstract: F-actin fibrils are the cytoskeleton of osteocytes. They react in a dynamic manner to mechanical loading, and strength and
reposition their efforts to reinforce the cells structure. We hypothesize that f-actin is temporarly disrupted after loading and repolymerizes
in a new orientation to oppose the applied load. In vitro studies are conducted to determine f-actin disruption after varying mechanical stimulus parameters that are known to affect bone
formation. Results indicate that the f-actin cytoskeleton is disrupted in vitro as a function of applied mechanical stimulus parameters and
that the f-actin bundles reassemble after loading induced disruption
within 3 minutes after cessation of loading. The disruption of the factin
cytoskeleton depends on the magnitude of stretch, the numbers
of loading cycles, frequency, the insertion of rest between loading
cycles and extracellular calcium. In vivo studies also demonstrate
disruption of the f-actin cytoskeleton in cells embedded in the bone
matrix immediately after mechanical loading. These studies suggest
that adaptation of the f-actin fiber bundles of the cytoskeleton in
response to applied loads occurs by disruption and subsequent repolymerization.
Abstract: Nowadays wireless technology plays an important
role in public and personal communication. However, the growth of
wireless networking has confused the traditional boundaries between
trusted and untrusted networks. Wireless networks are subject to a
variety of threats and attacks at present. An attacker has the ability to
listen to all network traffic which becoming a potential intrusion.
Intrusion of any kind may lead to a chaotic condition. In addition,
improperly configured access points also contribute the risk to
wireless network. To overcome this issue, a security solution that
includes an intrusion detection and prevention system need to be
implemented. In this paper, first the security drawbacks of wireless
network will be analyzed then investigate the characteristics and also
the limitations on current wireless intrusion detection and prevention
system. Finally, the requirement of next wireless intrusion prevention
system will be identified including some key issues which should be
focused on in the future to overcomes those limitations.
Abstract: Circle grid space filling plate is a flow conditioner with a fractal pattern and used to eliminate turbulence originating from pipe fittings in experimental fluid flow applications. In this paper, steady state, incompressible, swirling turbulent flow through circle grid space filling plate has been studied. The solution and the analysis were carried out using finite volume CFD solver FLUENT 6.2. Three turbulence models were used in the numerical investigation and their results were compared with the pressure drop correlation of BS EN ISO 5167-2:2003. The turbulence models investigated here are the standard k-ε, realizable k-ε, and the Reynolds Stress Model (RSM). The results showed that the RSM model gave the best agreement with the ISO pressure drop correlation. The effects of circle grids space filling plate thickness and Reynolds number on the flow characteristics have been investigated as well.
Abstract: Nowadays, the plant location selection has a critical
impact on the performance of numerous companies. In this paper, a
methodology is presented to solve this problem. The three decision
making methods, namely Delphi, AHP and improved VIKOR, are
hybridized in order to make the best use of information available
based on the decision makers or experts. In this respect, the aim of
using Delphi is to select the most influential criteria by a few decision
makers. The AHP is utilized to give weights of the selected criteria.
Finally, the improved VIKOR method is applied to rank alternatives.
At the end of paper, an application example demonstrates the
applicability of the proposed methodology.
Abstract: Economic crime (i.e. corporate fraud) has a
significant impact on business. This study analyzes the fraud cases
reported by the Malaysian Securities Commission. Frauds involving
market manipulation and/or illegal share trading are the most
common types of fraud reported over the 6 years analyzed. The
highest number of frauds reported involved investment and fund
holding companies. Alarmingly the results indicate quite a high
number of frauds cases are committed by management. The higher
number of Chinese perpetrators may be due to fact that they are the
dominant group in Malaysian business. The result also shows that
more than half of companies involved with fraud are privately held
companies in the investment/fund/finance sector. The results of this
study highlight general characteristic of perpetrators (person and
company) that commit fraud which could help the regulators in their
monitoring and enforcement activities. To investors, this would help
in analyzing their business investment or portfolio risk.
Abstract: Many recent electrophysiological studies have
revealed the importance of investigating meditation state in order to
achieve an increased understanding of autonomous control of
cardiovascular functions. In this paper, we characterize heart rate
variability (HRV) time series acquired during meditation using
nonlinear dynamical parameters. We have computed minimum
embedding dimension (MED), correlation dimension (CD), largest
Lyapunov exponent (LLE), and nonlinearity scores (NLS) from HRV
time series of eight Chi and four Kundalini meditation practitioners.
The pre-meditation state has been used as a baseline (control) state to
compare the estimated parameters. The chaotic nature of HRV during
both pre-meditation and meditation is confirmed by MED. The
meditation state showed a significant decrease in the value of CD and
increase in the value of LLE of HRV, in comparison with premeditation
state, indicating a less complex and less predictable nature
of HRV. In addition, it was shown that the HRV of meditation state
is having highest NLS than pre-meditation state. The study indicated
highly nonlinear dynamic nature of cardiac states as revealed by
HRV during meditation state, rather considering it as a quiescent
state.
Abstract: Contamination of heavy metals represents one of the
most pressing threats to water and soil resources as well as human
health. Phytoremediation can be potentially used to remediate metalcontaminated
sites. A major step towards the development of
phytoremediation of heavy metal impacted soils is the discovery of
the heavy metal hyperaccumulation in plants. In this study, the
several established criteria to define a hyperaccumulator plant were
applied. The case study was represented by a mining area in
Hamedan province in the central west part of Iran. Obtained results
showed that the most of sampled species were able to grow on
heavily metal-contaminated soils and also were able to accumulate
extraordinarily high concentrations of some metals such as Zn, Mn,
Cu, Pb and Fe. Using the most common criteria, Euphorbia
macroclada and Centaurea virgata can be classified as
hyperaccumulators of some measured heavy metals and, therefore,
they have suitable potential for phytoremediation of contaminated
soils.