Abstract: A study on the performance of TCP Vegas versus
different TCP variants in homogeneous and heterogeneous wired
networks are performed via simulation experiment using network
simulator (ns-2). This performance evaluation prepared a comparison
medium for the performance evaluation of enhanced-TCP Vegas in
wired network and for wireless network. In homogeneous network,
the performance of TCP Tahoe, TCP Reno, TCP NewReno, TCP
Vegas and TCP SACK are analyzed. In heterogeneous network, the
performances of TCP Vegas against TCP variants are analyzed. TCP
Vegas outperforms other TCP variants in homogeneous wired
network. However, TCP Vegas achieves unfair throughput in
heterogeneous wired network.
Abstract: Simplified coupled engine block-crankshaft models
based on beam theory provide an efficient substitute to engine
simulation in the design process. These models require accurate
definition of the main bearing stiffness. In this paper, an investigation
of this stiffness is presented. The clearance effect is studied using a
smooth bearing model. It is manifested for low shaft displacement.
The hydrodynamic assessment model shows that the oil film has no
stiffness for low loads and it is infinitely rigid for important loads.
The deformation stiffness is determined using a suitable finite
elements model based on real CADs. As a result, a main bearing
behaviour law is proposed. This behaviour law takes into account the
clearance, the hydrodynamic sustention and the deformation stiffness.
It ensures properly the transition from the configuration low rigidity
to the configuration high rigidity.
Abstract: Renewable natural fibres such as oil palm, flax, and
pineapple leaf can be utilized to obtain new high performance
polymer materials. The reuse of waste natural fibres as reinforcement
for polymer is a sustainable option to the environment. However, due
to its high hydroxyl content of cellulose, natural fibres are
susceptible to absorb water that affects the composite mechanical
properties adversely. Research found that Nano materials such as
Nano Silica Carbide (n-SiC) and Nano Clay can be added into the
polymer composite to overcome this problem by enhancing its
mechanical properties in wet condition. The addition of Nano
material improves the tensile and wear properties, flexural stressstrain
behaviour, fracture toughness, and fracture strength of polymer
natural composites in wet and dry conditions.
Abstract: This paper presents the experimental results of silicone rubber housing material for 24kV lightning arrester under artificial accelerated ageing test based on IEC 61109 specifications. Specimens having inclined and alternated shed made of HTV silicone rubber with ATH content and having leakage distance 625 mm were tested continuously 1000 hrs in artificial salt fog chamber. After 1000 hrs of salt fog ageing test, obviously surface erosion was observed on trunk between the upper large shed and the lower small shed near the energized end. Decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Chemical analysis by ATR-FTIR confirmed the observation results.
Abstract: The mechanism behind the electromigration and
thermomigration failure in flip-chip solder joints with Cu-pillar bumps
was investigated in this paper through using finite element method.
Hot spot and the current crowding occurrs in the upper corner of
copper column instead of solders of the common solder ball. The
simulation results show that the change in thermal gradient is
noticeable, which might greatly affect the reliability of solder joints
with Cu-pillar bumps under current stressing. When the average
applied current density is increased from 1×104 A/cm2 to 3×104 A/cm2
in solders, the thermal gradient would increase from 74 K/cm to 901
K/cm at an ambient temperature of 25°C. The force from thermal
gradient of 901 K/cm can nearly induce thermomigration by itself.
With the increase in applied current, the thermal gradient is growing. It
is proposed that thermomigration likely causes a serious reliability
issue for Cu column based interconnects.
Abstract: This paper presents a dynamic model for mechanical
loads of an electric drive, including angular misalignment and
including load unbalance. The misalignment model represents the
effects of the universal joint between the motor and the mechanical
load. Simulation results are presented for an induction motor driving
a mechanical load with angular misalignment for both flexible and
rigid coupling. The models presented are very useful in the study of
mechanical fault detection in induction motors, using mechanical and
electrical signals already available in a drive system, such as speed,
torque and stator currents.
Abstract: The mixture formation prior to the ignition process
plays as a key element in the diesel combustion. Parametric studies of
mixture formation and ignition process in various injection parameter
has received considerable attention in potential for reducing
emissions. Purpose of this study is to clarify the effects of injection
pressure on mixture formation and ignition especially during ignition
delay period, which have to be significantly influences throughout the
combustion process and exhaust emissions. This study investigated
the effects of injection pressure on diesel combustion fundamentally
using rapid compression machine. The detail behavior of mixture
formation during ignition delay period was investigated using the
schlieren photography system with a high speed camera. This method
can capture spray evaporation, spray interference, mixture formation
and flame development clearly with real images. Ignition process and
flame development were investigated by direct photography method
using a light sensitive high-speed color digital video camera. The
injection pressure and air motion are important variable that strongly
affect to the fuel evaporation, endothermic and prolysis process
during ignition delay. An increased injection pressure makes spray tip
penetration longer and promotes a greater amount of fuel-air mixing
occurs during ignition delay. A greater quantity of fuel prepared
during ignition delay period thus predominantly promotes more rapid
heat release.
Abstract: In this article, we aim to discuss the formulation of two explicit group iterative finite difference methods for time-dependent two dimensional Burger-s problem on a variable mesh. For the non-linear problems, the discretization leads to a non-linear system whose Jacobian is a tridiagonal matrix. We discuss the Newton-s explicit group iterative methods for a general Burger-s equation. The proposed explicit group methods are derived from the standard point and rotated point Crank-Nicolson finite difference schemes. Their computational complexity analysis is discussed. Numerical results are given to justify the feasibility of these two proposed iterative methods.
Abstract: Structural Integrity Management (SIM) is
important for the protection of offshore crew, environment, business assets and company and industry reputation. API RP 2A contained guidelines for assessment of existing platforms mostly for the Gulf
of Mexico (GOM). ISO 19902 SIM framework also does not
specifically cater for Malaysia. There are about 200 platforms in
Malaysia with 90 exceeding their design life. The Petronas Carigali
Sdn Bhd (PCSB) uses the Asset Integrity Management System and
the very subjective Risk based Inspection Program for these
platforms. Petronas currently doesn-t have a standalone Petronas
Technical Standard PTS-SIM. This study proposes a recommended
practice for the SIM process for offshore structures in Malaysia,
including studies by API and ISO and local elements such as the
number of platforms, types of facilities, age and risk ranking. Case
study on SMG-A platform in Sabah shows missing or scattered
platform data and a gap in inspection history. It is to undergo a level
3 underwater inspection in year 2015.
Abstract: In this paper a unified approach via block-pulse functions (BPFs) or shifted Legendre polynomials (SLPs) is presented to solve the linear-quadratic-Gaussian (LQG) control problem. Also a recursive algorithm is proposed to solve the above problem via BPFs. By using the elegant operational properties of orthogonal functions (BPFs or SLPs) these computationally attractive algorithms are developed. To demonstrate the validity of the proposed approaches a numerical example is included.
Abstract: Analytical procedure was carried out in this paper to
calculate the ultimate load capacity of reinforced concrete corbels
strengthened or repaired externally with CFRP sheets. Strut and tie
method and shear friction method proposed earlier for analyzing
reinforced concrete corbels were modified to incorporate the effect of
external CFRP sheets bonded to the corbel. The points of weakness
of any method that lead to an inaccuracy, especially when
overestimating test results were checked and discussed. Comparison
of prediction with the test data indicates that the ratio of test /
calculated ultimate load is 0.82 and 1.17 using strut and tie method
and shear friction method, respectively. If the limits of maximum
shear stress is followed, the calculated ultimate load capacity using
shear friction method was found to underestimates test data
considerably.
Abstract: This paper presents the experimental results of silicone rubber outdoor polymer insulators in salt fog ageing test based on IEC 61109. Specimens made ofHTV silicone rubber with ATH content having three different configurations, straight shedsalternated sheds, and incline and alternate sheds, were tested continuously 1000 hrs.in artificial salt fog chamber. Contamination level, reduction of hydrophobicity and hardness measurement were used as physical damaged inspection techniques to evaluate degree of surface deterioration. In addition, chemical changing of tested specimen surface was evaluated by ATR-FTIRto confirm physical damaged inspection. After 1000 hrs.of salt fog test, differences in degree of surface deterioration were observed on all tested specimens. Physical damaged inspection and chemical analysis results confirmed the experimental results as well.
Abstract: This paper presents a methodology to harvest the kinetic energy of the raindrops using piezoelectric devices. In the study 1m×1m PVDF (Polyvinylidene fluoride) piezoelectric membrane, which is fixed by the four edges, is considered for the numerical simulation on deformation of the membrane due to the impact of the raindrops. Then according to the drop size of the rain, the simulation is performed classifying the rainfall types into three categories as light stratiform rain, moderate stratiform rain and heavy thundershower. The impact force of the raindrop is dependent on the terminal velocity of the raindrop, which is a function of raindrop diameter. The results were then analyzed to calculate the harvestable energy from the deformation of the piezoelectric membrane.
Abstract: In this study, to compress ECG signals, KLT (Karhunen-
Loeve Transform) method has been used. The purpose of this method is to
perform effective ECG coding by a correlation between the length of frames
and the number of vectors of ECG signals.
Abstract: Discussion and development of principles of the
uniform nation formation within the limits of the Kazakhstan state
obviously became one of the most pressing questions of the day. The
fact that this question has not been solved "from above" as many
other questions has caused really brisk discussion, shows us increase
of civil consciousness in Kazakhstan society, and also the actuality of
this theme which can be carried in the category of fatal questions. In
any sense, nation building has raised civil society to a much higher
level. It would be better to begin with certain definitions. First is the
word "nation". The second is the "state". Both of these terms are very
closely connected with each other, so that in English language they
are in general synonyms. In Russian more shades of these terms
exist. For example in Kazakhstan the citizens of the country
irrespective of nationality (but mainly with reference to non-kazakhs)
are called «kazakhstanians», while the name of the title nation is
\"Kazakhs\". The same we can see in Russia, where, for example, the
Chechen or the Yakut –are \"Rossiyane\" which means “the citizens
of Russian Federation, but not \"Russians\".
The paper was written under the research project “Islam in modern
Kazakhstan: the nature and outcome of the religious revival”.
Abstract: Mapping between local and global coordinates is an
important issue in finite element method, as all calculations are
performed in local coordinates. The concern arises when subparametric
are used, in which the shape functions of the field variable
and the geometry of the element are not the same. This is particularly
the case for C* elements in which the extra degrees of freedoms
added to the nodes make the elements sub-parametric. In the present
work, transformation matrix for C1* (an 8-noded hexahedron
element with 12 degrees of freedom at each node) is obtained using
equivalent C0 elements (with the same number of degrees of
freedom). The convergence rate of 8-noded C1* element is nearly
equal to its equivalent C0 element, while it consumes less CPU time
with respect to the C0 element. The existence of derivative degrees
of freedom at the nodes of C1* element along with excellent
convergence makes it superior compared with it equivalent C0
element.
Abstract: The purpose of this study was to present a reliable mean for human-computer interfacing based on finger gestures made in two dimensions, which could be interpreted and adequately used in controlling a remote robot's movement. The gestures were captured and interpreted using an algorithm based on trigonometric functions, in calculating the angular displacement from one point of touch to another as the user-s finger moved within a time interval; thereby allowing for pattern spotting of the captured gesture. In this paper the design and implementation of such a gesture based user interface was presented, utilizing the aforementioned algorithm. These techniques were then used to control a remote mobile robot's movement. A resistive touch screen was selected as the gesture sensor, then utilizing a programmed microcontroller to interpret them respectively.
Abstract: This paper describes the experimental efficiency of a
compact organic Rankine cycle (ORC) system with a compact
rotary-vane-type expander. The compact ORC system can be used for
power generation from low-temperature heat sources such as waste
heat from various small-scale heat engines, fuel cells, electric devices,
and solar thermal energy. The purpose of this study is to develop an
ORC system with a low power output of less than 1 kW with a hot
temperature source ranging from 60°C to 100°C and a cold
temperature source ranging from 10°C to 30°C. The power output of
the system is rather less due to limited heat efficiency. Therefore, the
system should have an economically optimal efficiency. In order to
realize such a system, an efficient and low-cost expander is
indispensable. An experimental ORC system was developed using the
rotary-vane-type expander which is one of possible candidates of the
expander. The experimental results revealed the expander
performance for various rotation speeds, expander efficiencies, and
thermal efficiencies. Approximately 30 W of expander power output
with 48% expander efficiency and 4% thermal efficiency with a
temperature difference between the hot and cold sources of 80°C was
achieved.
Abstract: Renewable energy sources have gained ultimate urgency due to the need of the preservation of the environment for a sustainable development. Pyrolysis is an ultimate promising process in the recycling and acquisition of precious chemicals from wastes. Here, the co-pyrolysis of hazelnut shell with ultra-high molecular weight polyethylene was carried out catalytically and noncatalytically at 500 and 650 ºC. Potassium dichromate was added in certain amounts to act as a catalyst. The liquid, solid and gas products quantities were determined by gravimetry. As a main result, remarkable increases in gasification were observed by using this catalyst for pure components and their blends especially at 650 ºC. The increase in gas product quantity was compensated mainly with the decreases in the solid products and additionally in some cases liquid products quantities. These observations may stem from mainly the activation of carbon-carbon bonds rather than carbon-hydrogen bonds via potassium dichromate. Also, the catalytic effect of potassium dichromate on HS: PEO and HS: UHMWPE co-pyrolysis was compared.
Abstract: Bagging and boosting are among the most popular re-sampling ensemble methods that generate and combine a diversity of regression models using the same learning algorithm as base-learner. Boosting algorithms are considered stronger than bagging on noise-free data. However, there are strong empirical indications that bagging is much more robust than boosting in noisy settings. For this reason, in this work we built an ensemble using an averaging methodology of bagging and boosting ensembles with 10 sub-learners in each one. We performed a comparison with simple bagging and boosting ensembles with 25 sub-learners on standard benchmark datasets and the proposed ensemble gave better accuracy.