Abstract: In this paper, a robust fault detection and isolation
(FDI) scheme is developed to monitor a multivariable nonlinear
chemical process called the Chylla-Haase polymerization reactor,
when it is under the cascade PI control. The scheme employs a radial
basis function neural network (RBFNN) in an independent mode to
model the process dynamics, and using the weighted sum-squared
prediction error as the residual. The Recursive Orthogonal Least
Squares algorithm (ROLS) is employed to train the model to
overcome the training difficulty of the independent mode of the
network. Then, another RBFNN is used as a fault classifier to isolate
faults from different features involved in the residual vector. Several
actuator and sensor faults are simulated in a nonlinear simulation of
the reactor in Simulink. The scheme is used to detect and isolate the
faults on-line. The simulation results show the effectiveness of the
scheme even the process is subjected to disturbances and
uncertainties including significant changes in the monomer feed rate,
fouling factor, impurity factor, ambient temperature, and
measurement noise. The simulation results are presented to illustrate
the effectiveness and robustness of the proposed method.
Abstract: Selenium is an-antioxidant which is important for
human health enters food chain through crops. In Kenya Zea mays is
consumed by 96% of population hence is a cheap and convenient
method to provide selenium to large number of population. Several
soil factors are known to have antagonistic effects on selenium
speciation hence the uptake by Zea mays. There are no studies in
Kenya that has been done to determine the effects of soil
characteristics (pH, Tcarbon, CEC, Eh) affect accumulation of
selenium in Zea mays grains in Maize Belt in Kenya. About 100 Zea mays grain samples together with 100 soil samples
were collected from the study site put in separate labeled Ziplocs and
were transported to laboratories at room temperature for analysis.
Maize grains were analyzed for selenium while soil samples were
analyzed for pH, Cat Ion Exchange Capacity, total carbon, and
electrical conductivity. The mean selenium in Zea mays grains varied from 1.82 ± 0.76
mg/Kg to 11±0.86 mg/Kg. There was no significant difference
between selenium levels between different grain batches {χ (Df =76)
= 26.04 P= 1.00} The pH levels varied from 5.43± 0.58 to 5.85±
0.32. No significant correlations between selenium in grains and soil
pH (Pearson’s correlations = - 0.143), and between selenium levels in
grains and the four (pH, Tcarbon, CEC, Eh) soil chemical
characteristics {F (4,91) = 0.721 p = 0.579} was observed. It can be concluded that the soil chemical characteristics in the
study site did not significantly affect the accumulation of native
selenium in Zea mays grains.
Abstract: The objective of this work is to carryout critical
comparison of different actuation mechanisms like electrostatic,
thermal, piezoelectric, and magnetic with reference to a micro
cantilever. The relevant parameters like force generated,
displacement are compared in actuation methods. With these results,
helps in choosing the best actuation method for a particular
application. In this study, Comsol/Multiphysics software is used.
Modeling and simulation is done by considering the micro cantilever
of same dimensions as an actuator using all the above mentioned
actuation techniques. In addition to their small size, micro actuators
consume very little power and are capable of accurate results. In this
work, a comparison of actuation mechanisms is done to decide the
efficient system in micro domain.
Abstract: The laser-ultrasonic method is realized for
quantifying the influence of porosity on the local Young’s
modulus of isotropic composite materials. The method is based on
a laser thermooptical method of ultrasound generation combined
with measurement of the phase velocity of longitudinal and shear
acoustic waves in samples. The main advantage of this method
compared with traditional ultrasonic research methods is the
efficient generation of short and powerful probing acoustic pulses
required for reliable testing of ultrasound absorbing and
scattering heterogeneous materials. Using as an example samples
of a metal matrix composite with reinforcing microparticles of
silicon carbide in various concentrations, it is shown that to
provide an effective increase in Young’s modulus with increasing
concentration of microparticles, the porosity of the final sample
should not exceed 2%.
Abstract: The wider growing Finite Element Method (FEM)
application is caused by its benefits of cost saving and environment
friendly. Also, by using FEM a deep understanding of certain
phenomenon can be achieved. This paper observed the role of
material properties and volumetric change when Solid State Phase
Transformation (SSPT) takes place in residual stress formation due to
a welding process of ferritic steels through coupled Thermo-
Metallurgy-Mechanical (TMM) analysis. The correctness of FEM residual stress prediction was validated by
experiment. From parametric study of the FEM model, it can be
concluded that the material properties change tend to over-predicts
residual stress in the weld center whilst volumetric change tend to
underestimates it. The best final result is the compromise of both by
incorporates them in the model which has a better result compared to
a model without SSPT.
Abstract: In this paper genetic based test data compression is
targeted for improving the compression ratio and for reducing the
computation time. The genetic algorithm is based on extended pattern
run-length coding. The test set contains a large number of X value
that can be effectively exploited to improve the test data
compression. In this coding method, a reference pattern is set and its
compatibility is checked. For this process, a genetic algorithm is
proposed to reduce the computation time of encoding algorithm. This
coding technique encodes the 2n compatible pattern or the inversely
compatible pattern into a single test data segment or multiple test data
segment. The experimental result shows that the compression ratio
and computation time is reduced.
Abstract: In this paper, we propose two algorithms to optimally
solve makespan and total completion time scheduling problems with
learning effect and job dependent delivery times in a single machine
environment. The delivery time is the extra time to eliminate adverse
effect between the main processing and delivery to the customer. In
this paper, we introduce the job dependent delivery times for some
single machine scheduling problems with position dependent learning
effect, which are makespan are total completion. The results with
respect to two algorithms proposed for solving of the each problem
are compared with LINGO solutions for 50-jobs, 100-jobs and 150-
jobs problems. The proposed algorithms can find the same results in
shorter time.
Abstract: Cryosorption pumps are considered safe, quiet, and
ultra-high vacuum production pumps which have their application
from Semiconductor industries to ITER [International Thermonuclear
Experimental Reactor] units. The principle of physisorption of gases
over highly porous materials like activated charcoal at cryogenic
temperatures (below -1500°C) is involved in determining the
pumping speed of gases like Helium, Hydrogen, Argon, and
Nitrogen. This paper aims at providing detailed overview of
development of Cryosorption pump and characterization of different
activated charcoal materials that optimizes the performance of the
pump. Different grades of charcoal were tested in order to determine
the pumping speed of the pump and were compared with
commercially available Varian cryopanel. The results for bare panel,
bare panel with adhesive, cryopanel with pellets, and cryopanel with
granules were obtained and compared. The comparison showed that
cryopanel adhered with small granules gave better pumping speeds
than large sized pellets.
Abstract: Exact solution of an unsteady MHD flow of elasticoviscous
fluid through a porous media in a tube of elliptic cross
section under the influence of magnetic field and constant pressure
gradient has been obtained in this paper. Initially, the flow is
generated by a constant pressure gradient. After attaining the steady
state, the pressure gradient is suddenly withdrawn and the resulting
fluid motion in a tube of elliptical cross section by taking into
account of the porosity factor and magnetic parameter of the
bounding surface is investigated. The problem is solved in two-stages
the first stage is a steady motion in tube under the influence of a
constant pressure gradient, the second stage concern with an unsteady
motion. The problem is solved employing separation of variables
technique. The results are expressed in terms of a non-dimensional
porosity parameter, magnetic parameter and elastico-viscosity
parameter, which depends on the Non-Newtonian coefficient. The
flow parameters are found to be identical with that of Newtonian case
as elastic-viscosity parameter, magnetic parameter tends to zero, and
porosity tends to infinity. The numerical results were simulated in
MATLAB software to analyze the effect of Elastico-viscous
parameter, porosity parameter, and magnetic parameter on velocity
profile. Boundary conditions were satisfied. It is seen that the effect
of elastico-viscosity parameter, porosity parameter and magnetic
parameter of the bounding surface has significant effect on the
velocity parameter.
Abstract: The critical concern of satellite operations is to ensure
the health and safety of satellites. The worst case in this perspective
is probably the loss of a mission, but the more common interruption
of satellite functionality can result in compromised mission
objectives. All the data acquiring from the spacecraft are known as
Telemetry (TM), which contains the wealth information related to the
health of all its subsystems. Each single item of information is
contained in a telemetry parameter, which represents a time-variant
property (i.e. a status or a measurement) to be checked. As a
consequence, there is a continuous improvement of TM monitoring
systems to reduce the time required to respond to changes in a
satellite's state of health. A fast conception of the current state of the
satellite is thus very important to respond to occurring failures.
Statistical multivariate latent techniques are one of the vital learning
tools that are used to tackle the problem above coherently.
Information extraction from such rich data sources using advanced
statistical methodologies is a challenging task due to the massive
volume of data. To solve this problem, in this paper, we present a
proposed unsupervised learning algorithm based on Principle
Component Analysis (PCA) technique. The algorithm is particularly
applied on an actual remote sensing spacecraft. Data from the
Attitude Determination and Control System (ADCS) was acquired
under two operation conditions: normal and faulty states. The models
were built and tested under these conditions, and the results show that
the algorithm could successfully differentiate between these
operations conditions. Furthermore, the algorithm provides
competent information in prediction as well as adding more insight
and physical interpretation to the ADCS operation.
Abstract: Fresh water is one of the resources which is getting
depleted day by day. A wise method to address this issue is by the
application of renewable energy-sun irradiation and by means of
decentralized, cheap, energetically self-sufficient, robust and simple
to operate plants, distillates can be obtained from sea, river or even
sewage. Solar desalination is a technique used to desalinate water
using solar energy. The present work deals with the comprehensive
design and simulation of solar tracking system using LabVIEW,
temperature and mass flow rate control of the solar desalination plant
using LabVIEW and also analysis of single phase inverter circuit
with LC filters for solar pumping system in MATLAB. The main
objective of this work is to improve the performance of solar
desalination system using automatic tracking system, output control
using temperature and mass flow rate control system and also to
reduce the harmonic distortion in the solar pumping system by means
of LC filters. The simulation of single phase inverter was carried out
using MATLAB and the output waveforms were analyzed.
Simulations were performed for optimum output temperature control,
which in turn controls the mass flow rate of water in the thermal
collectors. Solar tracking system was accomplished using LABVIEW
and was tested successfully. The thermal collectors are tracked in
accordance with the sun’s irradiance levels, thereby increasing the
efficiency of the thermal collectors.
Abstract: This article presents the main results of a numerical
investigation on the uncertainty of dynamic response of structures
with statistically correlated random damping Gamma distributed. A
computational method based on a Linear Statistical Model (LSM) is
implemented to predict second order statistics for the response of a
typical industrial building structure. The significance of random
damping with correlated parameters and its implications on the
sensitivity of structural peak response in the neighborhood of a
resonant frequency are discussed in light of considerable ranges of
damping uncertainties and correlation coefficients. The results are
compared to those generated using Monte Carlo simulation
techniques. The numerical results obtained show the importance of
damping uncertainty and statistical correlation of damping
coefficients when obtaining accurate probabilistic estimates of
dynamic response of structures. Furthermore, the effectiveness of the
LSM model to efficiently predict uncertainty propagation for
structural dynamic problems with correlated damping parameters is
demonstrated.
Abstract: The ferrites ZnFe2O4, CdFe2O4 and CuFe2O4 are
synthesized in laboratory conditions using ceramic technology. Their
homogeneity and structure are proven by X-Ray diffraction analysis
and Mössbauer spectroscopy. The synthesized ferrites are subjected
to strong acid and high temperature leaching with solutions of H2SO4,
HCl and HNO3. The results indicate that the highest degree of
leaching of Zn, Cd and Cu from the ferrites is achieved by use of
HCl. The charging of five zinc sulfide concentrates was optimized using
the criterion of minimal amount of zinc ferrite produced when
roasting the concentrates in a fluidized bed. The results obtained are
interpreted in terms of the hydrometallurgical zinc production and
maximum recovery of zinc, copper and cadmium from initial zinc
concentrates after their roasting.
Abstract: The activation volume of 6082T6 aluminum is
investigated at different temperatures for grain size variants. The
deformation activation volume was computed on the basis of the
relationship between the Boltzmann’s constant k, the testing
temperatures, the material strain rate sensitivity and the material yield
stress grain size variants. The material strain rate sensitivity is
computed as a function of yield stress and strain rate grain size
variants. The effect of the material strain rate sensitivity and the
deformation activation volume of 6082T6 aluminum at different
temperatures of 3-D grain are discussed. It is shown that the strain rate sensitivities and activation volume
are negative for the grain size variants during the deformation of
nanostructured materials. It is also observed that the activation
volume vary in different ways with the equivalent radius, semi minor
axis radius, semi major axis radius and major axis radius. From the
obtained results it is shown that the variation of activation volume
increase and decrease with the testing temperature. It was revealed
that, increase in strain rate sensitivity led to decrease in activation
volume whereas increase in activation volume led to decrease in
strain rate sensitivity.
Abstract: This work deals with the problem of MHD mixed
convection in a completely porous and differentially heated vertical
channel. The model of Darcy-Brinkman-Forchheimer with the
Boussinesq approximation is adopted and the governing equations are
solved by the finite volume method. The effects of magnetic field and
buoyancy force intensities are given by the Hartmann and Richardson
numbers respectively, as well as the Joule heating represented by
Eckert number on the velocity and temperature fields, are examined.
The main results show an augmentation of heat transfer rate with the
decrease of Darcy number and the increase of Ri and Ha when Joule
heating is neglected.
Abstract: Cortisol is essential to the regulation of the immune
system and pathological yawning is a symptom of multiple sclerosis
(MS). Electromyography activity (EMG) in the jaw muscles typically
rises when the muscles are moved – extended or flexed; and yawning
has been shown to be highly correlated with cortisol levels in healthy
people as shown in the Thompson Cortisol Hypothesis. It is likely
that these elevated cortisol levels are also seen in people with MS.
The possible link between EMG in the jaw muscles and rises in saliva
cortisol levels during yawning were investigated in a randomized
controlled trial of 60 volunteers aged 18-69 years who were exposed
to conditions that were designed to elicit the yawning response.
Saliva samples were collected at the start and after yawning, or at the
end of the presentation of yawning-provoking stimuli, in the absence
of a yawn, and EMG data was additionally collected during rest and
yawning phases. Hospital Anxiety and Depression Scale, Yawning
Susceptibility Scale, General Health Questionnaire, demographic,
and health details were collected and the following exclusion criteria
were adopted: chronic fatigue, diabetes, fibromyalgia, heart
condition, high blood pressure, hormone replacement therapy,
multiple sclerosis, and stroke. Significant differences were found
between the saliva cortisol samples for the yawners, t (23) = -4.263, p
= 0.000, as compared with the non-yawners between rest and poststimuli,
which was non-significant. There were also significant
differences between yawners and non-yawners for the EMG
potentials with the yawners having higher rest and post-yawning
potentials. Significant evidence was found to support the Thompson
Cortisol Hypothesis suggesting that rises in cortisol levels are
associated with the yawning response. Further research is underway
to explore the use of cortisol as a potential diagnostic tool as an assist
to the early diagnosis of symptoms related to neurological disorders.
Bournemouth University Research & Ethics approval granted:
JC28/1/13-KA6/9/13. Professional code of conduct, confidentiality,
and safety issues have been addressed and approved in the Ethics
submission. Trials identification number: ISRCTN61942768.
http://www.controlled-trials.com/isrctn/
Abstract: An analytical 4-DOF nonlinear model of a de Laval
rotor-stator system based on Energy Principles has been used
theoretically and experimentally to investigate fault symptoms in a
rotating system. The faults, namely rotor-stator-rub, crack and
unbalance are modeled as excitations on the rotor shaft. Mayes
steering function is used to simulate the breathing behaviour of the
crack. The fault analysis technique is based on waveform signal,
orbits and Fast Fourier Transform (FFT) derived from simulated and
real measured signals. Simulated and experimental results manifest
considerable mutual resemblance of elliptic-shaped orbits and FFT
for a same range of test data.
Abstract: Nonlinear evolution of broadband ultrasonic pulses
passed through the rock specimens is studied using the apparatus
“GEOSCAN-02M”. Ultrasonic pulses are excited by the pulses of Qswitched
Nd:YAG laser with the time duration of 10 ns and with the
energy of 260 mJ. This energy can be reduced to 20 mJ by some light
filters. The laser beam radius did not exceed 5 mm. As a result of the
absorption of the laser pulse in the special material – the optoacoustic
generator–the pulses of longitudinal ultrasonic waves are excited with
the time duration of 100 ns and with the maximum pressure
amplitude of 10 MPa. The immersion technique is used to measure
the parameters of these ultrasonic pulses passed through a specimen,
the immersion liquid is distilled water. The reference pulse passed
through the cell with water has the compression and the rarefaction
phases. The amplitude of the rarefaction phase is five times lower
than that of the compression phase. The spectral range of the
reference pulse reaches 10 MHz. The cubic-shaped specimens of the
Karelian gabbro are studied with the rib length 3 cm. The ultimate
strength of the specimens by the uniaxial compression is (300±10)
MPa. As the reference pulse passes through the area of the specimen
without cracks the compression phase decreases and the rarefaction
one increases due to diffraction and scattering of ultrasound, so the
ratio of these phases becomes 2.3:1. After preloading some horizontal
cracks appear in the specimens. Their location is found by one-sided
scanning of the specimen using the backward mode detection of the
ultrasonic pulses reflected from the structure defects. Using the
computer processing of these signals the images are obtained of the
cross-sections of the specimens with cracks. By the increase of the
reference pulse amplitude from 0.1 MPa to 5 MPa the nonlinear
transformation of the ultrasonic pulse passed through the specimen
with horizontal cracks results in the decrease by 2.5 times of the
amplitude of the rarefaction phase and in the increase of its duration
by 2.1 times. By the increase of the reference pulse amplitude from 5
MPa to 10 MPa the time splitting of the phases is observed for the
bipolar pulse passed through the specimen. The compression and
rarefaction phases propagate with different velocities. These features
of the powerful broadband ultrasonic pulses passed through the rock
specimens can be described by the hysteresis model of Preisach-
Mayergoyz and can be used for the location of cracks in the optically
opaque materials.
Abstract: Heart is the most important part in the body of living
organisms. It affects and is affected by any factor in the body.
Therefore, it is a good detector for all conditions in the body. Heart
signal is a non-stationary signal; thus, it is utmost important to study
the variability of heart signal. The Heart Rate Variability (HRV) has
attracted considerable attention in psychology, medicine and has
become important dependent measure in psychophysiology and
behavioral medicine. The standards of measurements, physiological
interpretation and clinical use for HRV that are most often used were
described in many researcher papers, however, remain complex
issues are fraught with pitfalls. This paper presents one of the nonlinear
techniques to analyze HRV. It discusses many points like, what
Poincaré plot is and how Poincaré plot works; also, Poincaré plot's
merits especially in HRV. Besides, it discusses the limitation of
Poincaré cause of standard deviation SD1, SD2 and how to overcome
this limitation by using complex correlation measure (CCM). The
CCM is most sensitive to changes in temporal structure of the
Poincaré plot as compared toSD1 and SD2.
Abstract: Health workforce is a fundamental component of
health system and plays a significant role in delivering effective
health care services. However, there is a crucial shortage of skilled
personnel which make them prone to work in stressful conditions. In
spite of excessively high workload and burnout among the staff, little
attention is given to their job satisfaction level which has serious
implications on the productivity and effective performance of staff to
achieve organizational goals. Therefore, this study aims to explore
the job satisfaction of midwives working in the labor ward of the
Lady Dufferin Hospital, Karachi. A cross-sectional survey was
conducted. The short version of Minnesota Job Satisfaction
Questionnaire was administered on a convenient sample group of 22
midwives to gather information on their job satisfaction. The results
demonstrated that midwives were overall satisfied with their job. The
level of job satisfaction was however found different in various
positions within midwifery cadre. The head of midwives was highly
satisfied as compared to midwifery staff who works under the
supervision of head. The level of satisfaction of team leaders fall
between the head and staff of midwifery. Similar trends were
observed for both intrinsic and extrinsic job satisfaction. Such
evidences on these issues are essential and useful as it helps explore
the attitudes of individuals towards work which has direct
implications on access to quality care services. Strategic interventions
are required at organizational level to provide motivators and
satisfiers to health workers for their work related satisfaction and
enhanced motivation.