Abstract: One of the major cause of eye strain and other
problems caused while watching television is the relative illumination between the screen and its surrounding. This can be
overcome by adjusting the brightness of the screen with respect to the surrounding light. A controller based on fuzzy logic is proposed
in this paper. The fuzzy controller takes in the intensity of light
surrounding the screen and the present brightness of the screen as input. The output of the fuzzy controller is the grid voltage corresponding to the required brightness. This voltage is given to CRT and brightness is controller dynamically. For the given test system data, different de-fuzzifier methods have been implemented and the results are compared. In order to validate the effectiveness of
the proposed approach, a fuzzy controller has been designed by obtaining a test data from a real time system. The simulations are
performed in MATLAB and are verified with standard system data. The proposed approach can be implemented for real time
applications.
Abstract: Over the past few years, a number of efforts have
been exerted to build parallel processing systems that utilize the idle
power of LAN-s and PC-s available in many homes and corporations.
The main advantage of these approaches is that they provide cheap
parallel processing environments for those who cannot afford the
expenses of supercomputers and parallel processing hardware.
However, most of the solutions provided are not very flexible in the
use of available resources and very difficult to install and setup.
In this paper, a multi-level web-based parallel processing system
(MWPS) is designed (appendix). MWPS is based on the idea of
volunteer computing, very flexible, easy to setup and easy to use.
MWPS allows three types of subscribers: simple volunteers (single
computers), super volunteers (full networks) and end users. All of
these entities are coordinated transparently through a secure web site.
Volunteer nodes provide the required processing power needed by
the system end users. There is no limit on the number of volunteer
nodes, and accordingly the system can grow indefinitely. Both
volunteer and system users must register and subscribe. Once, they
subscribe, each entity is provided with the appropriate MWPS
components. These components are very easy to install.
Super volunteer nodes are provided with special components that
make it possible to delegate some of the load to their inner nodes.
These inner nodes may also delegate some of the load to some other
lower level inner nodes .... and so on. It is the responsibility of the
parent super nodes to coordinate the delegation process and deliver
the results back to the user.
MWPS uses a simple behavior-based scheduler that takes into
consideration the current load and previous behavior of processing
nodes. Nodes that fulfill their contracts within the expected time get a
high degree of trust. Nodes that fail to satisfy their contract get a
lower degree of trust.
MWPS is based on the .NET framework and provides the minimal
level of security expected in distributed processing environments.
Users and processing nodes are fully authenticated. Communications
and messages between nodes are very secure. The system has been
implemented using C#.
MWPS may be used by any group of people or companies to
establish a parallel processing or grid environment.
Abstract: Skyline extraction in mountainous images can be used
for navigation of vehicles or UAV(unmanned air vehicles), but it is
very hard to extract skyline shape because of clutters like clouds, sea
lines and field borders in images. We developed the edge-based
skyline extraction algorithm using a proposed multistage edge filtering
(MEF) technique. In this method, characteristics of clutters in the
image are first defined and then the lines classified as clutters are
eliminated by stages using the proposed MEF technique. After this
processing, we select the last line using skyline measures among the
remained lines. This proposed algorithm is robust under severe
environments with clutters and has even good performance for
infrared sensor images with a low resolution. We tested this proposed
algorithm for images obtained in the field by an infrared camera and
confirmed that the proposed algorithm produced a better performance
and faster processing time than conventional algorithms.
Abstract: Although a picture can be automatically a graphic
work, but especially in the field of graphics and images based on the
idea of advertising and graphic design will be prepared and
photographers to realize the design using his own knowledge and
skills to help does. It is evident that knowledge of photography,
photographer and designer of the facilities, fields of reaching a
higher level of quality offers. At the same time do not have a graphic
designer is also skilled photographer, but can execute your idea may
delegate to an expert photographer. Using technology and methods in
all fields of photography, graphic art may be applicable. But most of
its application in Iran, in works such as packaging, posters, Bill
Board, advertising, brochures and catalogs are. In this study, we
review how the images and techniques in the chart should be used in
Iranian graphic photo what impact has left. Using photography
techniques and procedures can be designed and helped advance the
goals graphic. Technique could not determine the idea. But what is
important to think about design and photography and his creativity
can flourish as a tool to be effective graphic designer in mind.
Computer software to help it's very promotes creativity techniques
shall graphic designer but also it is as a tool. Using images in various
fields, especially graphic arts and only because it is not being
documented, but applications are beautiful. As to his photographic
style from today is graphics. Graphic works try to affect impacts on
their audience. Hence the photo as an important factor is attention.
The other hand saw the man with the extent of forgiving and
understanding people's image, instead of using the word to your files,
allows large messages and concepts should be sent in the shortest
time. Posters, advertisements, brochures, catalog and packaging
products very diverse agricultural, industrial and food could not be
self-image. Today, the use of graphic images for a big score and the
photos to richen the role graphic design plays a major.
Abstract: The development of the poultry industry in Albania is mainly based on the existence of intensive modern farms with huge capacities, which often are mixed with other forms. Colibacillosis is commonly displayed regardless of the type of breeding, delivering high mortality in poultry industry. The mechanisms with which pathogen enterobacters are able to cause the infection in poultry are not yet clear. The routine diagnose in the field, followed by isolation of E. coli and species of Salmonella genres in reference laboratories cannot lead in classification or full recognition of circulative strains in a territory, if it is not performed a differentiation among the present microorganisms in intensive farms and those in rural areas. In this study were isolated 1.496 strains of E. coli and 378 Salmonella spp. This study, presents distribution of poultry pathogenosity of E.coli and Salmonella spp., based on the usage of innovative diagnostic methods.
Abstract: This paper sets forth the possibility and importance about applying Data Mining in Web logs mining and shows some problems in the conventional searching engines. Then it offers an improved algorithm based on the original AprioriAll algorithm which has been used in Web logs mining widely. The new algorithm adds the property of the User ID during the every step of producing the candidate set and every step of scanning the database by which to decide whether an item in the candidate set should be put into the large set which will be used to produce next candidate set. At the meantime, in order to reduce the number of the database scanning, the new algorithm, by using the property of the Apriori algorithm, limits the size of the candidate set in time whenever it is produced. Test results show the improved algorithm has a more lower complexity of time and space, better restrain noise and fit the capacity of memory.
Abstract: The latest Geographic Information System (GIS)
technology makes it possible to administer the spatial components of
daily “business object," in the corporate database, and apply suitable
geographic analysis efficiently in a desktop-focused application. We
can use wireless internet technology for transfer process in spatial
data from server to client or vice versa. However, the problem in
wireless Internet is system bottlenecks that can make the process of
transferring data not efficient. The reason is large amount of spatial
data. Optimization in the process of transferring and retrieving data,
however, is an essential issue that must be considered. Appropriate
decision to choose between R-tree and Quadtree spatial data indexing
method can optimize the process. With the rapid proliferation of
these databases in the past decade, extensive research has been
conducted on the design of efficient data structures to enable fast
spatial searching. Commercial database vendors like Oracle have also
started implementing these spatial indexing to cater to the large and
diverse GIS. This paper focuses on the decisions to choose R-tree
and quadtree spatial indexing using Oracle spatial database in mobile
GIS application. From our research condition, the result of using
Quadtree and R-tree spatial data indexing method in one single
spatial database can save the time until 42.5%.
Abstract: Electric vehicle (EV) is one of the effective solutions to
control emission of greenhouses gases in the world. It is of interest
for future transportation due to its sustainability and efficiency by
automotive manufacturers. Various electrical motors have been used
for propulsion system of electric vehicles in last decades. In this
paper brushed DC motor, Induction motor (IM), switched reluctance
motor (SRM) and brushless DC motor (BLDC) are simulated and
compared. BLDC motor is recommended for high performance
electric vehicles. PWM switching technique is implemented for speed
control of BLDC motor. Behavior of different modes of PWM speed
controller of BLDC motor are simulated in MATLAB/SIMULINK.
BLDC motor characteristics are compared and discussed for various
PWM switching modes under normal and inverter fault conditions.
Comparisons and discussions are verified through simulation results.
Abstract: Electroencephalogram (EEG) recordings are often
contaminated with ocular and muscle artifacts. In this paper, the
canonical correlation analysis (CCA) is used as blind source
separation (BSS) technique (BSS-CCA) to decompose the artifact
contaminated EEG into component signals. We combine the BSSCCA
technique with wavelet filtering approach for minimizing both
ocular and muscle artifacts simultaneously, and refer the proposed
method as wavelet enhanced BSS-CCA. In this approach, after
careful visual inspection, the muscle artifact components are
discarded and ocular artifact components are subjected to wavelet
filtering to retain high frequency cerebral information, and then clean
EEG is reconstructed. The performance of the proposed wavelet
enhanced BSS-CCA method is tested on real EEG recordings
contaminated with ocular and muscle artifacts, for which power
spectral density is used as a quantitative measure. Our results suggest
that the proposed hybrid approach minimizes ocular and muscle
artifacts effectively, minimally affecting underlying cerebral activity
in EEG recordings.
Abstract: In this paper, we evaluate the choice of suitable
quantization characteristics for both the decoder messages and the
received samples in Low Density Parity Check (LDPC) coded
systems using M-QAM (Quadrature Amplitude Modulation)
schemes. The analysis involves the demapper block that provides
initial likelihood values for the decoder, by relating its quantization
strategy of the decoder. A mapping strategy refers to the grouping of
bits within a codeword, where each m-bit group is used to select a
2m-ary signal in accordance with the signal labels. Further we
evaluate the system with mapping strategies like Consecutive-Bit
(CB) and Bit-Reliability (BR). A new demapper version, based on
approximate expressions, is also presented to yield a low complexity
hardware implementation.
Abstract: It has been shown that pH 7,3 and 37 0C are the optimal condition for the growth of E. coli “ASAP". The cells grow well on Glucose, Lactose, D-Mannitol, D-Sorbitol, (+)-Xylose, L- (+)-Arabinose and Dulcitol. No growth has been observed on Sucrose, Inositol, Phenylalanine, and Tryptophan. The strain is sensitive to a range of antibiotics. The present study has demonstrated that E. coli “ASAP" inhibit the growth of S. enterica ATCC #700931 in vitro. The studies on conjugating activity has revealed no conjugant of E. coli “ASAP" with plasmid strains E. coli G35#59 and S. enterica ATCC #700931. On the other hand, the conjugants with low frequencies were obtained from E. coli “ASAP" with E. coli G35#61, and E. coli “ASAP" with randomly chosen isolate from healthy human gut microflora: E. coli E6. The results of present study have demonstrated improvements in gut microflora condition of patients with different diseases after the administration of “ASAP"
Abstract: Multiparty voice over IP (MVoIP) systems allows a group of people to freely communicate each other via the internet, which have many applications such as online gaming, teleconferencing, online stock trading etc. Peertalk is a peer to peer multiparty voice over IP system (MVoIP) which is more feasible than existing approaches such as p2p overlay multicast and coupled distributed processing. Since the stream mixing and distribution are done by the peers, it is vulnerable to major security threats like nodes misbehavior, eavesdropping, Sybil attacks, Denial of Service (DoS), call tampering, Man in the Middle attacks etc. To thwart the security threats, a security framework called PEERTS (PEEred Reputed Trustworthy System for peertalk) is implemented so that efficient and secure communication can be carried out between peers.
Abstract: This paper presents a pulse doubling technique in a 12-pulse ac-dc converter which supplies direct torque controlled motor drives (DTCIMD-s) in order to have better power quality conditions at the point of common coupling. The proposed technique increases the number of rectification pulses without significant changes in the installations and yields in harmonic reduction in both ac and dc sides. The 12-pulse rectified output voltage is accomplished via two paralleled six-pulse ac-dc converters each of them consisting of three-phase diode bridge rectifier. An autotransformer is designed to supply the rectifiers. The design procedure of magnetics is in a way such that makes it suitable for retrofit applications where a six-pulse diode bridge rectifier is being utilized. Independent operation of paralleled diode-bridge rectifiers, i.e. dc-ripple re-injection methodology, requires a Zero Sequence Blocking Transformer (ZSBT). Finally, a tapped interphase reactor is connected at the output of ZSBT to double the pulse numbers of output voltage up to 24 pulses. The aforementioned structure improves power quality criteria at ac mains and makes them consistent with the IEEE-519 standard requirements for varying loads. Furthermore, near unity power factor is obtained for a wide range of DTCIMD operation. A comparison is made between 6- pulse, 12-pulse, and proposed converters from view point of power quality indices. Results show that input current total harmonic distortion (THD) is less than 5% for the proposed topology at various loads.
Abstract: In this paper present a sensorless maximum wind power extraction for variable speed constant frequency (VSCF) wind power generation systems with a doubly-fed induction generators (DFIG), to ensure stability and to impose the ideal feedback control solution despite of model uncertainties , using the principles of an active and reactive power controller (DPC) a robust sliding mode power control has been proposed to guarantees fast response times and precise control actions for control the active and reactive power independently. The simulation results in MATLAB/Simulink platform confirmed the good dynamic performance of power control approach for DFIGbased variable speed wind turbines.
Abstract: Typical Intelligent Decision Support System is 4-based, its design composes of Data Warehouse, Online Analytical Processing, Data Mining and Decision Supporting based on models, which is called Decision Support System Based on Data Warehouse (DSSBDW). This way takes ETL,OLAP and DM as its implementing means, and integrates traditional model-driving DSS and data-driving DSS into a whole. For this kind of problem, this paper analyzes the DSSBDW architecture and DW model, and discusses the following key issues: ETL designing and Realization; metadata managing technology using XML; SQL implementing, optimizing performance, data mapping in OLAP; lastly, it illustrates the designing principle and method of DW in DSSBDW.
Abstract: The focus of the study is to understand the factors of
curriculum innovation from the perspective of Language teacher
education. The overall aim of the study is to investigate Language
educators- perceptions of factors of curriculum innovation. In the
theoretical framework the main focus is on discussion about different
curriculum approaches for language teacher education and limiting
and facilitating factors of innovation. In order to achieve the aim of
the study, an observational research is employed. The empirical basis
of the study consists of questionnaire with sixty-three language
teachers from eight Romanian higher education institutions. The
findings reveal variation in Language teachers- conceptions of the
dominant factors of curricular innovation.
Abstract: The brain MR imaging-based clinical research and analysis system were specifically built and the development for a large-scale data was targeted. We used the general clinical data available for building large-scale data. Registration period for the selection of the lesion ROI and the region growing algorithm was used and the Mesh-warp algorithm for matching was implemented. The accuracy of the matching errors was modified individually. Also, the large ROI research data can accumulate by our developed compression method. In this way, the correctly decision criteria to the research result was suggested. The experimental groups were age, sex, MR type, patient ID and smoking which can easily be queries. The result data was visualized of the overlapped images by a color table. Its data was calculated by the statistical package. The evaluation for the utilization of this system in the chronic ischemic damage in the area has done from patients with the acute cerebral infarction. This is the cause of neurologic disability index location in the center portion of the lateral ventricle facing. The corona radiate was found in the position. Finally, the system reliability was measured both inter-user and intra-user registering correlation.
Abstract: The evolutionary design of electronic circuits, or
evolvable hardware, is a discipline that allows the user to
automatically obtain the desired circuit design. The circuit
configuration is under the control of evolutionary algorithms. Several
researchers have used evolvable hardware to design electrical
circuits. Every time that one particular algorithm is selected to carry
out the evolution, it is necessary that all its parameters, such as
mutation rate, population size, selection mechanisms etc. are tuned in
order to achieve the best results during the evolution process. This
paper investigates the abilities of evolution strategy to evolve digital
logic circuits based on programmable logic array structures when
different mutation rates are used. Several mutation rates (fixed and
variable) are analyzed and compared with each other to outline the
most appropriate choice to be used during the evolution of
combinational logic circuits. The experimental results outlined in this
paper are important as they could be used by every researcher who
might need to use the evolutionary algorithm to design digital logic
circuits.
Abstract: In this paper, a nonconforming mixed finite element method is studied for semilinear pseudo-hyperbolic partial integrodifferential equations. By use of the interpolation technique instead of the generalized elliptic projection, the optimal error estimates of the corresponding unknown function are given.
Abstract: Nowadays, cardiac disease is one of the most common
cause of death. Each year almost one million of angioplasty interventions and stents implantations are made all over the world.
Unfortunately, in 20-30% of cases neointimal proliferations leads to
restenosis occurring within the following period of 3-6 months. Three major factors are believed to contribute mostly to the edge
restenosis: (a) mechanical damage of the artery-s wall caused by the
stent implantation, (b) interaction between the stent and the blood constituents and (c) endothelial growth stimulation by small (lower
that 1.5 Pa) and oscillating wall shear stress. Assuming that this last actor is particularly important, a numerical model of restenosis
basing on wall shear stress distribution in the stented artery was elaborated. A numerical simulations of the development of in-stent
restenosis have been performed and realistic geometric patterns of a
progressing lumen reduction have been obtained