Abstract: In the present study, the surface temperature history of the adaptor part in a two-stage supersonic launch vehicle is accurately predicted. The full Navier-Stokes equations are used to estimate the aerodynamic heat flux and the one-dimensional heat conduction in solid phase is used to compute the temperature history. The instantaneous surface temperature is used to improve the applied heat flux, to improve the accuracy of the results.
Abstract: Load managing method on road became necessary
since overloaded vehicles occur damage on road facilities and existing
systems for preventing this damage still show many
problems.Accordingly, efficient managing system for preventing
overloaded vehicles could be organized by using the road itself as a
scale by applying genetic algorithm to analyze the load and the drive
information of vehicles.Therefore, this paper organized Ubiquitous
sensor network system for development of intelligent overload vehicle
regulation system, also in this study, to use the behavior of road, the
transformation was measured by installing underground box type
indoor model and indoor experiment was held using genetic algorithm.
And we examined wireless possibility of overloaded vehicle
regulation system through experiment of the transmission and
reception distance.If this system will apply to road and bridge, might
be effective for economy and convenience through establishment of
U-IT system..
Abstract: Most of the collision warning systems currently
available in the automotive market are mainly designed to warn
against imminent rear-end and lane-changing collisions. No collision
warning system is commercially available to warn against imminent
turning collisions at intersections, especially for left-turn collisions
when a driver attempts to make a left-turn at either a signalized or
non-signalized intersection, conflicting with the path of other
approaching vehicles traveling on the opposite-direction traffic
stream. One of the major factors that lead to left-turn collisions is the
human error and misjudgment of the driver of the turning vehicle
when perceiving the speed and acceleration of other vehicles
traveling on the opposite-direction traffic stream; therefore, using a
properly-designed collision warning system will likely reduce, or
even eliminate, this type of collisions by reducing human error. This
paper introduces perceptual framework for a proposed collision
warning system that can detect imminent left-turn collisions at
intersections. The system utilizes a commercially-available detection
sensor (either a radar sensor or a laser detector) to detect approaching
vehicles traveling on the opposite-direction traffic stream and
calculate their speeds and acceleration rates to estimate the time-tocollision
and compare that time to the time required for the turning
vehicle to clear the intersection. When calculating the time required
for the turning vehicle to clear the intersection, consideration is given
to the perception-reaction time of the driver of the turning vehicle,
which is the time required by the driver to perceive the message
given by the warning system and react to it by engaging the throttle.
A regression model was developed to estimate perception-reaction
time based on age and gender of the driver of the host vehicle.
Desired acceleration rate selected by the driver of the turning vehicle,
when making the left-turn movement, is another human factor that is
considered by the system. Another regression model was developed
to estimate the acceleration rate selected by the driver of the turning
vehicle based on driver-s age and gender as well as on the location
and speed of the nearest approaching vehicle along with the
maximum acceleration rate provided by the mechanical
characteristics of the turning vehicle. By comparing time-to-collision
with the time required for the turning vehicle to clear the intersection,
the system displays a message to the driver of the turning vehicle
when departure is safe. An application example is provided to
illustrate the logic algorithm of the proposed system.
Abstract: The aim of the study was to identify seat belt wearing
factor among road users in Malaysia. Evidence-based approach
through in-depth crash investigation was utilised to determine the
intended objectives. The objective was scoped into crashes
investigated by Malaysian Institute of Road Safety Research
(MIROS) involving passenger vehicles within 2007 and 2010. Crash
information of a total of 99 crash cases involving 240 vehicles and
864 occupants were obtained during the study period. Statistical test
and logistic regression analysis have been performed. Results of the
analysis revealed that gender, seat position and age were associated
with seat belt wearing compliance in Malaysia. Males are 97.6%
more likely to wear seat belt compared to females (95% CI 1.317 to
2.964). By seat position, the finding indicates that frontal occupants
were 82 times more likely to be wearing seat belt (95% CI 30.199 to
225.342) as compared to rear occupants. It is also important to note
that the odds of seat belt wearing increased by about 2.64% (95% CI
1.0176 to 1.0353) for every one year increase in age. This study is
essential in understanding the Malaysian tendency in belting up
while being occupied in a vehicle. The factors highlighted in this
study should be emphasized in road safety education in order to
increase seat belt wearing rate in this country and ultimately in
preventing deaths due to road crashes.
Abstract: This paper presents an algorithm for the recognition
and tracking of moving objects, 1/10 scale model car is used to verify
performance of the algorithm. Presented algorithm for the recognition
and tracking of moving objects in the paper is as follows. SURF
algorithm is merged with Lucas-Kanade algorithm. SURF algorithm
has strong performance on contrast, size, rotation changes and it
recognizes objects but it is slow due to many computational
complexities. Processing speed of Lucas-Kanade algorithm is fast but
the recognition of objects is impossible. Its optical flow compares the
previous and current frames so that can track the movement of a pixel.
The fusion algorithm is created in order to solve problems which
occurred using the Kalman Filter to estimate the position and the
accumulated error compensation algorithm was implemented. Kalman
filter is used to create presented algorithm to complement problems
that is occurred when fusion two algorithms. Kalman filter is used to
estimate next location, compensate for the accumulated error. The
resolution of the camera (Vision Sensor) is fixed to be 640x480. To
verify the performance of the fusion algorithm, test is compared to
SURF algorithm under three situations, driving straight, curve, and
recognizing cars behind the obstacles. Situation similar to the actual is
possible using a model vehicle. Proposed fusion algorithm showed
superior performance and accuracy than the existing object
recognition and tracking algorithms. We will improve the performance
of the algorithm, so that you can experiment with the images of the
actual road environment.
Abstract: Undoubtedly, chassis is one of the most important
parts of a vehicle. Chassis that today are produced for vehicles are
made up of four parts. These parts are jointed together by screwing.
Transverse parts are called cross member.
This study reviews the stress generated by cyclic laboratory loads
in front cross member of Peugeot 405. In this paper the finite element
method is used to simulate the welding process and to determine the
physical response of the spot-welded joints. Analysis is done by the
Abaqus software.
The Stresses generated in cross member structure are generally
classified into two groups: The stresses remained in form of residual
stresses after welding process and the mechanical stress generated by
cyclic load. Accordingly the total stress must be obtained by
determining residual stress and mechanical stress separately and then
sum them according to the superposition principle.
In order to improve accuracy, material properties including
physical, thermal and mechanical properties were supposed to be
temperature-dependent. Simulation shows that maximum Von Misses
stresses are located at special points. The model results are then
compared to the experimental results which are reported by
producing factory and good agreement is observed.