Abstract: For vacuum cleaned dust filters there exist no calculation methods to determine design parameters (e.g. traverse velocity of the nozzle, filter area…). In this work a method to calculate the optimum traverse velocity of the nozzle of an industrial-size flat dust filter at a given mean pressure drop and filter face velocity was elaborated. Well-known equations for the design of a cleanable multi-chamber bag-house-filter were modified in order to take into account a continuously regeneration of a dust filter by a nozzle. Thereby, the specific filter medium resistance and the specific cake resistance values are needed which can be derived from filter tests under constant operation conditions.
A lab-scale filter test rig was used to derive the specific filter media resistance value and the specific cake resistance value for vacuum cleaned filter operation. Three different filter media were tested and the determined parameters were compared to each other.
Abstract: The evaluation of the convective heat transfer of flow in passages with rectangular cross section is still of interest for the heat transfer investigators, as in the air heater solar collectors. The aim of this paper is to present investigation results on the natural convection heat transfer in a solar air heater. The effect of the channel length as heat transfer surface and the inclination of the passage were investigated. The results were obtained experimentally and theoretically. For that, an experimental test rig was fabricated with channel lengths of 1m, 1.5m, and 2m. For each length, the air outlet and inlet temperatures, absorber and cover temperatures, solar radiation intensity and air flow rate were measured at 10o, 30o, 50o, 70o, and 90o tilt angles. Measurements were recorded every 2 hours interval to investigate the transient behavior of the system. The experimental and theoretical results are presented in terms of Nu number versus Ra number and discussed. The percentages of differences between experimental and theoretical results are within the margin of 6% to 13%, effectively. It is recommended to extend the investigation to study the same configurations with different artificial surface roughing by ribs or pins.
Abstract: This paper presents a cold flow simulation study of a small gas turbine combustor performed using laboratory scale test rig. The main objective of this investigation is to obtain physical insight of the main vortex, responsible for the efficient mixing of fuel and air. Such models are necessary for predictions and optimization of real gas turbine combustors. Air swirler can control the combustor performance by assisting in the fuel-air mixing process and by producing recirculation region which can act as flame holders and influences residence time. Thus, proper selection of a swirler is needed to enhance combustor performance and to reduce NOx emissions. Three different axial air swirlers were used based on their vane angles i.e., 30°, 45°, and 60°. Three-dimensional, viscous, turbulent, isothermal flow characteristics of the combustor model operating at room temperature were simulated via Reynolds- Averaged Navier-Stokes (RANS) code. The model geometry has been created using solid model, and the meshing has been done using GAMBIT preprocessing package. Finally, the solution and analysis were carried out in a FLUENT solver. This serves to demonstrate the capability of the code for design and analysis of real combustor. The effects of swirlers and mass flow rate were examined. Details of the complex flow structure such as vortices and recirculation zones were obtained by the simulation model. The computational model predicts a major recirculation zone in the central region immediately downstream of the fuel nozzle and a second recirculation zone in the upstream corner of the combustion chamber. It is also shown that swirler angles changes have significant effects on the combustor flowfield as well as pressure losses.
Abstract: This study aims to specify to what extent students
understand topology during the lesson and to determine possible
misconceptions. 14 teacher trainees registered at Secondary School
Mathematics education department were observed in the topology
lessons throughout a semester and data collected at the first topology
lesson is presented here. Students- knowledge was evaluated using a
written test right before and after the topology lesson. Thus, what the
students learnt in terms of the definition and examples of topologic
space were specified as well as possible misconceptions. The
findings indicated that students did not fully comprehend the topic
and misunderstandings were due to insufficient pre-requisite
knowledge of abstract mathematical topics and mathematical
notation.
Abstract: This paper describes the design process and the realtime validation of an innovative autonomous mid-air flight and landing system developed by the Italian Aerospace Research Center in the framework of the Italian national funded project TECVOL (Technologies for the Autonomous Flight). In the paper it is provided an insight of the whole development process of the system under study. In particular, the project framework is illustrated at first, then the functional context and the adopted design and testing approach are described, and finally the on-ground validation test rig on purpose designed is addressed in details. Furthermore, the hardwarein- the-loop validation of the autonomous mid-air flight and landing system by means of the real-time test rig is described and discussed.
Abstract: Axial Flux Permanent Magnet (AFPM) Machines require effective cooling due to their high power density. The detrimental effects of overheating such as degradation of the insulation materials, magnets demagnetization, and increase of Joule losses are well known. This paper describes the CFD simulations performed on a test rig model of an air cooled Axial Flux Permanent Magnet (AFPM) generator built at Durham University to identify the temperatures and heat transfer coefficient on the stator. The Reynolds Averaged Navier-Stokes and the Energy equations are solved and the flow pattern and heat transfer developing inside the machine are described. The Nusselt number on the stator surfaces has been found. The dependency of the heat transfer on the flow field is described temperature field obtained. Tests on an experimental are undergoing in order to validate the CFD results.
Abstract: This paper presents the design, fabrication and
evaluation of magneto-rheological damper. Semi-active control
devices have received significant attention in recent years because
they offer the adaptability of active control devices without requiring
the associated large power sources. Magneto-Rheological (MR)
dampers are semi- active control devices that use MR fluids to
produce controllable dampers. They potentially offer highly reliable
operation and can be viewed as fail-safe in that they become passive
dampers if the control hardware malfunction. The advantage of MR
dampers over conventional dampers are that they are simple in
construction, compromise between high frequency isolation and
natural frequency isolation, they offer semi-active control, use very
little power, have very quick response, has few moving parts, have a
relax tolerances and direct interfacing with electronics. Magneto-
Rheological (MR) fluids are Controllable fluids belonging to the
class of active materials that have the unique ability to change
dynamic yield stress when acted upon by an electric or magnetic
field, while maintaining viscosity relatively constant. This property
can be utilized in MR damper where the damping force is changed by
changing the rheological properties of the fluid magnetically. MR
fluids have a dynamic yield stress over Electro-Rheological fluids
(ER) and a broader operational temperature range. The objective of
this papert was to study the application of an MR damper to vibration
control, design the vibration damper using MR fluids, test and
evaluate its performance. In this paper the Rheology and the theory
behind MR fluids and their use on vibration control were studied.
Then a MR vibration damper suitable for vehicle suspension was
designed and fabricated using the MR fluid. The MR damper was
tested using a dynamic test rig and the results were obtained in the
form of force vs velocity and the force vs displacement plots. The
results were encouraging and greatly inspire further research on the
topic.
Abstract: Although water only takes a little percentage in the total mass of soil, it indeed plays an important role to the strength of structure. Moisture transfer can be carried out by many different mechanisms which may involve heat and mass transfer, thermodynamic phase change, and the interplay of various forces such as viscous, buoyancy, and capillary forces. The continuum models are not well suited for describing those phenomena in which the connectivity of the pore space or the fracture network, or that of a fluid phase, plays a major role. However, Lattice Boltzmann methods (LBMs) are especially well suited to simulate flows around complex geometries. Lattice Boltzmann methods were initially invented for solving fluid flows. Recently, fluid with multicomponent and phase change is also included in the equations. By comparing the numerical result with experimental result, the Lattice Boltzmann methods with phase change will be optimized.
Abstract: As a part of the development of a numerical method of
close capture exhausts systems for machining devices, a test rig
recreating a situation similar to a grinding operation, but in a
perfectly controlled environment, is used. The properties of the
obtained spray of solid particles are initially characterized using
particle tracking velocimetry (PTV), in order to obtain input and
validation parameters for numerical simulations. The dispersion of a
tracer gas (SF6) emitted simultaneously with the particle jet is then
studied experimentally, as the dispersion of such a gas is
representative of that of finer particles, whose aerodynamic response
time is negligible. Finally, complete modeling of the test rig is
achieved to allow comparison with experimental results and thus to
progress towards validation of the models used to describe a twophase
flow generated by machining operation.
Abstract: The aim of this work is to investigate on the internalflow
patterns in a plate heat exchanger channel, which affect the
rate of sedimentation fouling on the heat transfer surface of the
plate heat exchanger. The research methodologies were the
computer simulation using Computational Fluid Dynamics (CFD)
and the experimental works. COMSOL MULTIPHYSICS™
Version 3.3 was used to simulate the velocity flow fields to verify
the low and high flow regions. The results from the CFD technique
were then compared with the images obtained from the
experiments in which the fouling test rig was set up with a singlechannel
plate heat exchanger to monitor the fouling of calcium
carbonate. Two parameters were varied i.e., the crossing angle of
the two plate: 55/55, 10/10, and 55/10 degree, and the fluid flow
rate at the inlet: 0.0566, 0.1132 and 0.1698 m/s. The type of plate
“GX-12" (the surface area 0.12 m2, the depth 2.9 mm, the width of
fluid flow 215 mm and the thickness of stainless plate of 0.5 mm)
was used in this study. The results indicated that the velocity
distribution for the case of 55/55 degree seems to be very well
organized when compared with the others. Also, an increase in the
inlet velocity resulted in the reduction of fouling rate on the surface
of plate heat exchangers.