Abstract: Fuel and oxidant gas delivery plate, or fuel cell
plate, is a key component of a Proton Exchange Membrane (PEM)
fuel cell. To manufacture low-cost and high performance fuel cell
plates, advanced computer modeling and finite element structure
analysis are used as virtual prototyping tools for the optimization
of the plates at the early design stage. The present study examines
thermal stress analysis of the fuel cell plates that are produced
using a patented, low-cost fuel cell plate production technique
based on screen-printing. Design optimization is applied to
minimize the maximum stress within the plate, subject to strain
constraint with both geometry and material parameters as design
variables. The study reveals the characteristics of the printed
plates, and provides guidelines for the structure and material design
of the fuel cell plate.
Abstract: All practical real-time scheduling algorithms in multiprocessor systems present a trade-off between their computational complexity and performance. In real-time systems, tasks have to be performed correctly and timely. Finding minimal schedule in multiprocessor systems with real-time constraints is shown to be NP-hard. Although some optimal algorithms have been employed in uni-processor systems, they fail when they are applied in multiprocessor systems. The practical scheduling algorithms in real-time systems have not deterministic response time. Deterministic timing behavior is an important parameter for system robustness analysis. The intrinsic uncertainty in dynamic real-time systems increases the difficulties of scheduling problem. To alleviate these difficulties, we have proposed a fuzzy scheduling approach to arrange real-time periodic and non-periodic tasks in multiprocessor systems. Static and dynamic optimal scheduling algorithms fail with non-critical overload. In contrast, our approach balances task loads of the processors successfully while consider starvation prevention and fairness which cause higher priority tasks have higher running probability. A simulation is conducted to evaluate the performance of the proposed approach. Experimental results have shown that the proposed fuzzy scheduler creates feasible schedules for homogeneous and heterogeneous tasks. It also and considers tasks priorities which cause higher system utilization and lowers deadline miss time. According to the results, it performs very close to optimal schedule of uni-processor systems.
Abstract: This paper deals with a numerical analysis of the
transient response of composite beams with strain rate dependent
mechanical properties by use of a finite difference method. The
equations of motion based on Timoshenko beam theory are derived.
The geometric nonlinearity effects are taken into account with von
Kármán large deflection theory. The finite difference method in
conjunction with Newmark average acceleration method is applied to
solve the differential equations. A modified progressive damage
model which accounts for strain rate effects is developed based on
the material property degradation rules and modified Hashin-type
failure criteria and added to the finite difference model. The
components of the model are implemented into a computer code in
Mathematica 6. Glass/epoxy laminated composite beams with
constant and strain rate dependent mechanical properties under
dynamic load are analyzed. Effects of strain rate on dynamic
response of the beam for various stacking sequences, load and
boundary conditions are investigated.
Abstract: In this paper, a particle swarm optimization (PSO)
algorithm is proposed to solve machine loading problem in flexible
manufacturing system (FMS), with bicriterion objectives of
minimizing system unbalance and maximizing system throughput in
the occurrence of technological constraints such as available
machining time and tool slots. A mathematical model is used to
select machines, assign operations and the required tools. The
performance of the PSO is tested by using 10 sample dataset and the
results are compared with the heuristics reported in the literature. The
results support that the proposed PSO is comparable with the
algorithms reported in the literature.
Abstract: In this paper, a plane-strain orthotropic elasto-plastic
dynamic constitutive model is established, and with this constitutive
model, the thermal shock wave induced by intense pulsed X-ray
radiation in cylinder shell composite is simulated by the finite element
code, then the properties of thermal shock wave propagation are
discussed. The results show that the thermal shock wave exhibit
different shapes under the radiation of soft and hard X-ray, and while
the composite is radiated along different principal axes, great
differences exist in some aspects, such as attenuation of the peak stress
value, spallation and so on.
Abstract: This paper presents a generalized formulation for the
problem of buckling optimization of anisotropic, radially graded,
thin-walled, long cylinders subject to external hydrostatic pressure.
The main structure to be analyzed is built of multi-angle fibrous
laminated composite lay-ups having different volume fractions of the
constituent materials within the individual plies. This yield to a
piecewise grading of the material in the radial direction; that is the
physical and mechanical properties of the composite material are
allowed to vary radially. The objective function is measured by
maximizing the critical buckling pressure while preserving the total
structural mass at a constant value equals to that of a baseline
reference design. In the selection of the significant optimization
variables, the fiber volume fractions adjoin the standard design
variables including fiber orientation angles and ply thicknesses. The
mathematical formulation employs the classical lamination theory,
where an analytical solution that accounts for the effective axial and
flexural stiffness separately as well as the inclusion of the coupling
stiffness terms is presented. The proposed model deals with
dimensionless quantities in order to be valid for thin shells having
arbitrary thickness-to-radius ratios. The critical buckling pressure
level curves augmented with the mass equality constraint are given
for several types of cylinders showing the functional dependence of
the constrained objective function on the selected design variables. It
was shown that material grading can have significant contribution to
the whole optimization process in achieving the required structural
designs with enhanced stability limits.
Abstract: This paper is concerned with the application of small
rating Capacitive Energy Storage units for the improvement of
Automatic Generation Control of a multiunit multiarea power
system. Generation Rate Constraints are also considered in the
investigations. Integral Squared Error technique is used to obtain the
optimal integral gain settings by minimizing a quadratic performance
index. Simulation studies reveal that with CES units, the deviations
in area frequencies and inter-area tie-power are considerably
improved in terms of peak deviations and settling time as compared
to that obtained without CES units.
Abstract: E-Appointment Scheduling (EAS) has been developed
to handle appointment for UMP students, lecturers in Faculty of
Computer Systems & Software Engineering (FCSSE) and Student
Medical Center. The schedules are based on the timetable and
university activities. Constraints Logic Programming (CLP) has been
implemented to solve the scheduling problems by giving
recommendation to the users in part of determining any available
slots from the lecturers and doctors- timetable. By using this system,
we can avoid wasting time and cost because this application will set
an appointment by auto-generated. In addition, this system can be an
alternative to the lecturers and doctors to make decisions whether to
approve or reject the appointments.
Abstract: An alarming emergence of multidrug-resistant strains
of the tuberculosis pathogen Mycobacterium tuberculosis and
continuing high worldwide incidence of tuberculosis has invigorated
the search for novel drug targets. The enzyme glutamate racemase
(MurI) in bacteria catalyzes the stereoconversion of L-glutamate to
D-glutamate which is a component of the peptidoglycan cell wall of
the bacterium. The inhibitors targeted against MurI from several
bacterial species have been patented and are advocated as promising
antibacterial agents. However there are none available against MurI
from Mycobacterium tuberculosis, due to the lack of its threedimensional
structure. This work accomplished two major objectives.
First, the tertiary structure of MtMurI was deduced computationally
through homology modeling using the templates from bacterial
homologues. It is speculated that like in other Gram-positive bacteria,
MtMurI exists as a dimer and many of the protein interactions at the
dimer interface are also conserved. Second, potent candidate
inhibitors against MtMurI were identified through docking against
already known inhibitors in other organisms.
Abstract: Nature conducts its action in a very private manner. To
reveal these actions classical science has done a great effort. But
classical science can experiment only with the things that can be seen
with eyes. Beyond the scope of classical science quantum science
works very well. It is based on some postulates like qubit,
superposition of two states, entanglement, measurement and
evolution of states that are briefly described in the present paper.
One of the applications of quantum computing i.e.
implementation of a novel quantum evolutionary algorithm(QEA) to
automate the time tabling problem of Dayalbagh Educational Institute
(Deemed University) is also presented in this paper. Making a good
timetable is a scheduling problem. It is NP-hard, multi-constrained,
complex and a combinatorial optimization problem. The solution of
this problem cannot be obtained in polynomial time. The QEA uses
genetic operators on the Q-bit as well as updating operator of
quantum gate which is introduced as a variation operator to converge
toward better solutions.
Abstract: A research program is conducted to evaluate the
mechanical properties of Ultra High Performance Concrete, target
compressive strength at the age of 28 days being more than 150 MPa.
The methodology to develop such mix has been explained. The
material properties, mix design and curing regime are determined.
The material attributes are understood by studying the stress strain
behaviour of UHPC cylinders under uniaxial compressive loading.
The load –crack mouth opening displacement (cmod) of UHPC
beams, flexural strength and fracture energy was evaluated using
third point loading test. Compressive strength and Split tensile
strength results are determined to find out the compressive and tensile
behaviour. Residual strength parameters are presented vividly
explaining the flexural performance, toughness of concrete.Durability
studies were also done to compare the effect of fibre to that of a
control mix For all the studies the Mechanical properties were
evaluated by varying the percentage and aspect ratio of steel fibres
The results reflected that higher aspect ratio and fibre volume
produced drastic changes in the cube strength, cylinder strength, post
peak response, load-cmod, fracture energy flexural strength, split
tensile strength, residual strength and durability. In regards to null
application of UHPC in India, an initiative is undertaken to
comprehend the mechanical behaviour of UHPC, which will be vital
for longer run in commercialization for structural applications.
Abstract: Fourty one strains of ESBL producing P.aeruginosa
which were previously isolated from burn patients in Kerman
University general hospital, Iran were subjected to PCR, RFLP and
sequencing in order to determine the type of extended spectrum β-
lactamases (ESBL), the restriction digestion pattern and possibility of
mutation among detected genes. DNA extraction was carried out by
phenol chloroform method. PCR for detection of bla genes was
performed using specific primer for each gene. Restriction Fragment
Length Polymorphism (RFLP) for ESBL genes was carried out using
EcoRI, NheI, PVUII, EcoRV, DdeI, and PstI restriction enzymes. The
PCR products were subjected to direct sequencing of both the strands
for identification of the ESBL genes.The blaCTX-M, blaVEB-1, blaPER-1,
blaGES-1, blaOXA-1, blaOXA-4 and blaOXA-10 genes were detected in the
(n=1) 2.43%, (n=41)100%, (n=28) 68.3%, (n=10) 24.4%, (n=29)
70.7%, (n=7)17.1% and (n=38) 92.7% of the ESBL producing isolates
respectively. The RFLP analysis showed that each ESBL gene has
identical pattern of digestion among the isolated strains. Sequencing
of the ESBL genes confirmed the genuinety of PCR products and
revealed no mutation in the restriction sites of the above genes. From
results of the present investigation it can be concluded that blaVEB-1
and blaCTX-M were the most and the least frequently isolated ESBL
genes among the P.aeruginosa strains isolated from burn patients. The
RFLP and sequencing analysis revealed that same clone of the bla
genes were indeed existed among the antibiotic resistant strains.
Abstract: Motion estimation is the most computationally
intensive part in video processing. Many fast motion estimation
algorithms have been proposed to decrease the computational
complexity by reducing the number of candidate motion vectors.
However, these studies are for fast search algorithms themselves while
almost image and video compressions are operated with software
based. Therefore, the timing constraints for running these motion
estimation algorithms not only challenge for the video codec but also
overwhelm for some of processors. In this paper, the performance of
motion estimation is enhanced by using Intel's Streaming SIMD
Extension 2 (SSE2) technology with Intel Pentium 4 processor.
Abstract: In this paper, a nonlinear model predictive swing-up
and stabilizing sliding controller is proposed for an inverted
pendulum-cart system. In the swing up phase, the nonlinear model
predictive control is formulated as a nonlinear programming problem
with energy based objective function. By solving this problem at
each sampling instant, a sequence of control inputs that optimize the
nonlinear objective function subject to various constraints over a
finite horizon are obtained. Then, this control drives the pendulum to
a predefined neighborhood of the upper equilibrium point, at where
sliding mode based model predictive control is used to stabilize the
systems with the specified constraints. It is shown by the simulations
that, due to the way of formulating the problem, short horizon
lengths are sufficient for attaining the swing up goal.
Abstract: Repetitive systems stand for a kind of systems that
perform a simple task on a fixed pattern repetitively, which are
widely spread in industrial fields. Hence, many researchers have been
interested in those systems, especially in the field of iterative learning
control (ILC). In this paper, we propose a finite-horizon tracking
control scheme for linear time-varying repetitive systems with uncertain
initial conditions. The scheme is derived both analytically
and numerically for state-feedback systems and only numerically for
output-feedback systems. Then, it is extended to stable systems with
input constraints. All numerical schemes are developed in the forms
of linear matrix inequalities (LMIs). A distinguished feature of the
proposed scheme from the existing iterative learning control is that
the scheme guarantees the tracking performance exactly even under
uncertain initial conditions. The simulation results demonstrate the
good performance of the proposed scheme.
Abstract: The financial crisis has decreased the opportunities of
small businesses to acquire financing through conventional financial
actors, such as commercial banks. This credit constraint is partly the
reason for the emergence of new alternatives of financing, in addition
to the spreading opportunities for communication and secure
financial transfer through Internet. One of the most interesting venues
for finance is termed “crowdfunding". As the term suggests
crowdfunding is an appeal to prospective customers and investors to
form a crowd that will finance projects that otherwise would find it
hard to generate support through the most common financial actors.
Crowdfunding is in this paper divided into different models; the
threshold model, the microfinance model, the micro loan model and
the equity model. All these models add to the financial possibilities of
emerging entrepreneurs.
Abstract: The paper considered the construction of BIBDs using potential Lotto Designs (LDs) earlier derived from qualifying parent BIBDs. The study utilized Li’s condition pr t−1 ( t−1 2 ) + pr− pr t−1 (t−1) 2 < ( p 2 ) λ, to determine the qualification of a parent BIBD (v, b, r, k, λ) as LD (n, k, p, t) constrained on v ≥ k, v ≥ p, t ≤ min{k, p} and then considered the case k = t since t is the smallest number of tickets that can guarantee a win in a lottery. The (15, 140, 28, 3, 4) and (7, 7, 3, 3, 1) BIBDs were selected as parent BIBDs to illustrate the procedure. These BIBDs yielded three potential LDs each. Each of the LDs was completely generated and their properties studied. The three LDs from the (15, 140, 28, 3, 4) produced (9, 84, 28, 3, 7), (10, 120, 36, 3, 8) and (11, 165, 45, 3, 9) BIBDs while those from the (7, 7, 3, 3, 1) produced the (5, 10, 6, 3, 3), (6, 20, 10, 3, 4) and (7, 35, 15, 3, 5) BIBDs. The produced BIBDs follow the generalization (v + 1, b + r + λ + 1, r +λ+1, k, λ+1) where (v, b, r, k, λ) are the parameters of the (9, 84, 28, 3, 7) and (5, 10, 6, 3, 3) BIBDs. All the BIBDs produced are unreduced designs.
Abstract: This study aims to propose three evaluation methods to
evaluate the Tokyo Cap and Trade Program when emissions trading is
performed virtually among enterprises, focusing on carbon dioxide
(CO2), which is the only emitted greenhouse gas that tends to increase.
The first method clarifies the optimum reduction rate for the highest
cost benefit, the second discusses emissions trading among enterprises
through market trading, and the third verifies long-term emissions
trading during the term of the plan (2010-2019), checking the validity
of emissions trading partly using Geographic Information Systems
(GIS). The findings of this study can be summarized in the following
three points.
1. Since the total cost benefit is the greatest at a 44% reduction rate, it
is possible to set it more highly than that of the Tokyo Cap and
Trade Program to get more total cost benefit.
2. At a 44% reduction rate, among 320 enterprises, 8 purchasing
enterprises and 245 sales enterprises gain profits from emissions
trading, and 67 enterprises perform voluntary reduction without
conducting emissions trading. Therefore, to further promote
emissions trading, it is necessary to increase the sales volumes of
emissions trading in addition to sales enterprises by increasing the
number of purchasing enterprises.
3. Compared to short-term emissions trading, there are few enterprises
which benefit in each year through the long-term emissions trading
of the Tokyo Cap and Trade Program. Only 81 enterprises at the
most can gain profits from emissions trading in FY 2019. Therefore,
by setting the reduction rate more highly, it is necessary to increase
the number of enterprises that participate in emissions trading and
benefit from the restraint of CO2 emissions.
Abstract: This paper presents the source extraction system which can extract only target signals with constraints on source localization in on-line systems. The proposed system is a kind of methods for enhancing a target signal and suppressing other interference signals. But, the performance of proposed system is superior to any other methods and the extraction of target source is comparatively complete. The method has a beamforming concept and uses an improved time-frequency (TF) mask-based BSS algorithm to separate a target signal from multiple noise sources. The target sources are assumed to be in front and test data was recorded in a reverberant room. The experimental results of the proposed method was evaluated by the PESQ score of real-recording sentences and showed a noticeable speech enhancement.
Abstract: Deformable active contours are widely used in
computer vision and image processing applications for image
segmentation, especially in biomedical image analysis. The active
contour or “snake" deforms towards a target object by controlling the
internal, image and constraint forces. However, if the contour
initialized with a lesser number of control points, there is a high
probability of surpassing the sharp corners of the object during
deformation of the contour. In this paper, a new technique is
proposed to construct the initial contour by incorporating prior
knowledge of significant corners of the object detected using the
Harris operator. This new reconstructed contour begins to deform, by
attracting the snake towards the targeted object, without missing the
corners. Experimental results with several synthetic images show the
ability of the new technique to deal with sharp corners with a high
accuracy than traditional methods.