Abstract: Lately, an interest has grown greatly in the usages of
RFID in an un-presidential applications. It is shown in the adaptation
of major software companies such as Microsoft, IBM, and Oracle
the RFID capabilities in their major software products. For example
Microsoft SharePoints 2010 workflow is now fully compatible with
RFID platform. In addition, Microsoft BizTalk server is also capable
of all RFID sensors data acquisition. This will lead to applications
that required high bit rate, long range and a multimedia content in
nature. Higher frequencies of operation have been designated for
RFID tags, among them are the 2.45 and 5.8 GHz. The higher the
frequency means higher range, and higher bit rate, but the drawback
is the greater cost. In this paper we present a single layer, low
profile patch antenna operates at 5.8 GHz with pure resistive input
impedance of 50 and close to directive radiation. Also, we propose
a modification to the design in order to improve the operation band
width from 8.7 to 13.8
Abstract: Movable power sources of proton exchange
membrane fuel cells (PEMFC) are the important research done in the
current fuel cells (FC) field. The PEMFC system control influences
the cell performance greatly and it is a control system for industrial
complex problems, due to the imprecision, uncertainty and partial
truth and intrinsic nonlinear characteristics of PEMFCs. In this paper
an adaptive PI control strategy using neural network adaptive Morlet
wavelet for control is proposed. It is based on a single layer feed
forward neural networks with hidden nodes of adaptive morlet
wavelet functions controller and an infinite impulse response (IIR)
recurrent structure. The IIR is combined by cascading to the network
to provide double local structure resulting in improving speed of
learning. The proposed method is applied to a typical 1 KW PEMFC
system and the results show the proposed method has more accuracy
against to MLP (Multi Layer Perceptron) method.
Abstract: The dome with ribs and rings, which covers the
ROMEXPO pavilion from Bucharest, was designed after the collapse
of the single layer reticulated dome. In this paper, it was made the
checking of the structure, under the dynamic loads with three
recorded accelerograms calibrated according to Romanian seismic
design code P100-1/2006. Under the action the dynamic loadings, it
was made a time-history analysis to determine the zones where the
plastic hinges appear, at what accelerations and their position on the
structure. The studied dome is formed by 32 spatial semi arches and
three rings: one circular ring located at the top of the dome and
another two rings, design as trusses, the first near the supports and the
second as an intermediate rings above the skylights. Above the
skylights up to the top, the dome is tight together with purlins and
bracings.
Abstract: The paper presents a detailed calculation of characteristic of five different topology permanent magnet machines for high performance traction including hybrid -electric vehicles using finite element analysis (FEA) method. These machines include V-shape single layer interior PM, W-shape single-layer interior PM, Segment interior PM and surface PM on the rotor and with distributed winding on the stator. The performance characteristics which include the back-emf voltage and its harmonic, magnet mass, iron loss and ripple torque are compared and analyzed. One of a 7.5kW IPM prototype was tested and verified finite-element analysis results. The aim of the paper is given some guidance and reference for machine designer which are interested in IPM machine selection for high performance traction application.
Abstract: The present investigation aimed to study the
histomorphometric characterizations of the thyroid gland of the duck.
Five adult male and five adult female ducks were used in the
experiment. Results showed that the overall histological structure of
the thyroid gland of the duck were similar to those of the other
vertebrae. The gland consisted of roughly spherical randomly
distributed micro and macrofollicles with very little interstitial tissue
between them. Each follicle is lined by a single layer of epithelial
cells enclosing a cavity, the follicular cavity, which is filled with
colloid. Ultrastructural findings showed that the apical surface of the
follicular cells bears a variable number of short, irregularly
distributed microvilli which are apparently more numerous on the
columnar cells than on the lower, relatively inactive cells.
Mitochondria and rough endoplasmic reticulum occupy the
subnuclear region of the follicular cell, whereas the Golgi complex,
free ribosomes and colloid droplets were found in the apical
cytoplasm. At light or electron microscopic levels, there was no sex
difference in histomorphometric characteristics of the thyroid
glands.ls.
Abstract: Prestressing in structure increases ratio of load-bearing capacity to weight. Suspendomes are single-layer braced domes reinforced with cable and strut. Prestressing of cables alter value and distribution of stress in structure. In this study two configuration, diamatic and lamella domes is selected. Investigated domes have span of 100m with rise-to-span ratios of 0.1, 0.2, and 0.3. Single layer domes loaded under service load combinations according to ISO code. After geometric nonlinear analysis, models are designed with tubular and I-shaped sections then reinforced with cable and strut and converted to suspendomes. Displacements and stresses of some groups of nodes and elements in all of single-layer domes and suspendomes for three load combinations, symmetric snow, asymmetric snow and wind are compared. Variation due to suspending system is investigated. Suspendomes are redesigned and minimum possible weight after addition of cable and strut is obtained.
Abstract: Evaluation of contact pressure, surface and
subsurface contact stresses are essential to know the functional
response of surface coatings and the contact behavior mainly depends
on surface roughness, material property, thickness of layer and the
manner of loading. Contact parameter evaluation of real rough
surface contacts mostly relies on statistical single asperity contact
approaches. In this work, a three dimensional layered solid rough
surface in contact with a rigid flat is modeled and analyzed using
finite element method. The rough surface of layered solid is
generated by FFT approach. The generated rough surface is exported
to a finite element method based ANSYS package through which the
bottom up solid modeling is employed to create a deformable solid
model with a layered solid rough surface on top. The discretization
and contact analysis are carried by using the same ANSYS package.
The elastic, elastoplastic and plastic deformations are continuous in
the present finite element method unlike many other contact models.
The Young-s modulus to yield strength ratio of layer is varied in the
present work to observe the contact parameters effect while keeping
the surface roughness and substrate material properties as constant.
The contacting asperities attain elastic, elastoplastic and plastic states
with their continuity and asperity interaction phenomena is inherently
included. The resultant contact parameters show that neighboring
asperity interaction and the Young-s modulus to yield strength ratio
of layer influence the bulk deformation consequently affect the
interface strength.