Abstract: A low profile planar antenna for twelve-band operation in the mobile phone is presented. The proposed antenna radiating elements occupy an area equals 17 × 50 mm2 are mounted on the compact no-ground portion of the system circuit board to achieve a simple low profile structure. In order to overcome the shortcoming of narrow bandwidth for conventional planar printed antenna, a novel bandwidth enhancement approach for multiband handset antennas is proposed here. The technique used in this study shows that by using a coupled-fed mechanism and a slotted ground structure, a multiband operation with wideband characteristic can be achieved. The influences of the modifications introduced into the ground plane improved significantly the bandwidths of the designed antenna. The slotted ground plane structure with the coupled-fed elements contributes their lowest, middle and higher-order resonant modes to form four operating modes. The generated modes are able to cover LTE 700/2300/2500, GSM 850/900/1800/1900, UMTS, WiMAX 3500, WLAN 2400/5200/5800 operations. Parametric studies via simulation are provided and discussed. Proposed antenna’s gain, efficiency and radiation pattern characteristics over the desired operating bands are obtained and discussed. The reasonable results observed can meet the requirements of practical mobile phones.
Abstract: This paper presents a resonant-based read-out circuit for capacitive pressure sensors. The proposed read-out circuit consists of an LC oscillator and a counter. The circuit detects the capacitance changes of a capacitive pressure sensor by means of frequency shifts from its nominal operation frequency. The proposed circuit is designed in 0.18 m CMOS with an estimated power consumption of 43.1mW. Simulation results show that the circuit has a capacitive resolution of 8.06kHz/fF, which enables it for high resolution pressure detection.
Abstract: The possibility of intrinsic electromagnetic fields
within living cells and their resonant self-interaction and interaction
with ambient electromagnetic fields is suggested on the basis of a
theoretical and experimental study. It is reported that intrinsic
electromagnetic fields are produced in the form of radio-frequency
and infra-red photons within atoms (which may be coupled or
uncoupled) in cellular structures, such as the cell cytoskeleton and
plasma membrane. A model is presented for the interaction of these
photons among themselves or with atoms under a dipole-dipole
coupling, induced by single-photon or two-photon processes. This
resonance is manifested by conspicuous field amplification and it is
argued that it is possible for these resonant photons to undergo
tunnelling in the form of evanescent waves to a short range (of a few
nanometers to micrometres). This effect, suggested as a resonant
photon tunnelling mechanism in this report, may enable these fields
to act as intracellular signal communication devices and as bridges
between macromolecules or cellular structures in the cell
cytoskeleton, organelles or membrane. A brief overview of an
experimental technique and a review of some preliminary results are
presented, in the detection of these fields produced in living cell
membranes under physiological conditions.
Abstract: With a development of Hybrid Electric Vehicle(HEV),
A photovoltaic(PV) generation system is used for charging batteries in many cases. A dc/dc converter using PV power for a battery charger
requires a high efficiency. In this paper, A ZVS boost converter using the renewable energies for HEV charger is proposed. Through the theoretical analysis and experimental result, operation modes and characteristics of the proposed topology are verified.
Abstract: This paper proposes a feed-forward control in
resonant dc link inverter. The feed-forward control configuration is
based on synchronous sigma-delta modulation. The simulation
results showing the proposed technique can reject non-ideal dc bus
improving the total harmonic distortion.
Abstract: In electronegative-electropositive gas mixtures plasma, at a total pressure varying in the range of ten to hundred Torr, the appearance of a quasi-mochromatization effect of the emitted radiation was reported. This radiation could be the result of the generating mechanisms at molecular level, which is the case of the excimer radiation but also at atomic level. Thus, in the last case, in (Ne+1%Ar/Xe+H2) gas mixtures plasma in a dielectric barrier discharge, this effect, called M-effect, consists in the reduction of the discharge emission spectrum practice at one single, strong spectral line with λ = 585.3 nm. The present paper is concerned with the characteristics comparative investigation of the principal reaction mechanisms involved in the quasi-monochromatization effect existence in the case of the excimer radiation, respectively of the Meffect. Also, the paper points out the role of the metastable electronegative atoms in the appearance of the monochromatization – effect at atomic level.
Abstract: The induction hardening machines are utilized in
the industries which modify machine parts and tools needed to
achieve high ware resistance. This paper describes the model of
induction heating process design of inverter circuit and the results
of induction surface hardening of heating coil. In the design of
heating coil, the shape and the turn numbers of the coil are very
important design factors because they decide the overall operating
performance of induction heater including resonant frequency, Q
factor, efficiency and power factor. The performance will be tested
by experiments in some cases high frequency induction hardening
machine.
Abstract: This paper describes the development, modeling, and
testing of skyhook and MiniMax control strategies of semi-active
suspension. The control performances are investigated using
Matlab/Simulink [1], with a two-degree-of-freedom quarter car semiactive
suspension system model. The comparison and evaluation of
control result are made using software-in-the-loop simulation (SILS)
method. This paper also outlines the development of a hardware-inthe-
loop simulation (HILS) system. The simulation results show that
skyhook strategy can significantly reduce the resonant peak of body
and provide improvement in vehicle ride comfort. Otherwise,
MiniMax strategy can be employed to effectively improve drive
safety of vehicle by influencing wheel load. The two strategies can
be switched to control semi-active suspension system to fulfill
different requirement of vehicle in different stages.
Abstract: In this article the influence of higher frequency effects
in addition to a special damper design on the electrical behavior of a
synchronous generator main exciter machine is investigated. On the
one hand these machines are often highly stressed by harmonics from
the bridge rectifier thus facing additional eddy current losses. On the
other hand the switching may cause the excitation of dangerous
voltage peaks in resonant circuits formed by the diodes of the
rectifier and the commutation reactance of the machine. Therefore
modern rotating exciters are treated like synchronous generators
usually modeled with a second order equivalent circuit. Hence the
well known Standstill Frequency Response Test (SSFR) method is
applied to a test machine in order to determine parameters for the
simulation. With these results it is clearly shown that higher
frequencies have a strong impact on the conventional equivalent
circuit model. Because of increasing field displacement effects in the
stranded armature winding the sub-transient reactance is even smaller
than the armature leakage at high frequencies. As a matter of fact this
prevents the algorithm to find an equivalent scheme. This issue is
finally solved using Laplace transfer functions fully describing the
transient behavior at the model ports.
Abstract: Three similar negative differential resistance (NDR)
profiles with both high peak to valley current density ratio (PVCDR)
value and high peak current density (PCD) value in unity resonant
tunneling electronic circuit (RTEC) element is developed in this paper.
The PCD values and valley current density (VCD) values of the three
NDR curves are all about 3.5 A and 0.8 A, respectively. All PV values
of NDR curves are 0.40 V, 0.82 V, and 1.35 V, respectively. The VV
values are 0.61 V, 1.07 V, and 1.69 V, respectively. All PVCDR
values reach about 4.4 in three NDR curves. The PCD value of 3.5 A
in triple PVCDR RTEC element is better than other resonant
tunneling devices (RTD) elements. The high PVCDR value is
concluded the lower VCD value about 0.8 A. The low VCD value is
achieved by suitable selection of resistors in triple PVCDR RTEC
element. The low PV value less than 1.35 V possesses low power
dispersion in triple PVCDR RTEC element. The designed multiple
value logical level (MVLL) system using triple PVCDR RTEC
element provides equidistant logical level. The logical levels of
MVLL system are about 0.2 V, 0.8 V, 1.5 V, and 2.2 V from low
voltage to high voltage and then 2.2 V, 1.3 V, 0.8 V, and 0.2 V from
high voltage back to low voltage in half cycle of sinusoid wave. The
output level of four levels MVLL system is represented in 0.3 V, 1.1 V,
1.7 V, and 2.6 V, which satisfies the NMP condition of traditional
two-bit system. The remarkable logical characteristic of improved
MVLL system with paralleled capacitor are with four significant
stable logical levels about 220 mV, 223 mV, 228 mV, and 230 mV.
The stability and articulation of logical levels of improved MVLL
system are outstanding. The average holding time of improved MVLL
system is approximately 0.14 μs. The holding time of improved
MVLL system is fourfold than of basic MVLL system. The function of
additional capacitor in the improved MVLL system is successfully
discovered.
Abstract: In this paper, the design of a multiple U-slotted microstrip patch antenna with frequency selective surface (FSS) as a superstrate for WLAN and WiMAX applications is presented. The proposed antenna is designed by using substrate FR4 having permittivity of 4.4 and air substrate. The characteristics of the antenna are designed and evaluated the performance of modelled antenna using CST Microwave studio. The proposed antenna dual resonant frequency has been achieved in the band of 2.37-2.55 GHz and 3.4-3.6 GHz. Because of the impact of FSS superstrate, it is found that the bandwidths have been improved from 6.12% to 7.35 % and 3.7% to 5.7% at resonant frequencies 2.45 GHz and 3.5 GHz, respectively. The maximum gain at the resonant frequency of 2.45 and 3.5 GHz are 9.3 and 11.33 dBi, respectively.
Abstract: A new mechanism responsible for structural life
consumption due to resonant fatigue in turbine blades, or vanes, is
presented and explained. A rotating blade or vane in a gas turbine can
change its contour due to erosion and/or material build up, in any of
these instances, the surface pressure distribution occurring on the
suction and pressure sides of blades-vanes can suffer substantial
modification of their pressure and temperatures envelopes and flow
characteristics. Meanwhile, the relative rotation between the blade
and duct vane while the pressurized gas flows and the consequent
wake crossings, will induce a fluctuating thrust force or lift that will
excite the blade.
An actual totally used up set of vane-blade components in a HP
turbine power stage in a gas turbine is analyzed. The blade suffered
some material erosion mostly at the trailing edge provoking a
peculiar surface pressure envelope which evolved as the relative
position between the vane and the blade passed in front of each other.
Interestingly preliminary modal analysis for this eroded blade
indicates several natural frequencies within the aeromechanic power
spectrum, moreover, the highest frequency component is 94% of one
natural frequency indicating near resonant condition.
Independently of other simultaneously occurring fatigue cycles
(such as thermal, centrifugal stresses).
Abstract: This paper proposes a zero-voltage transition (ZVT) PWM synchronous buck converter, which is designed to operate at low output voltage and high efficiency typically required for portable systems. To make the DC-DC converter efficient at lower voltage, synchronous converter is an obvious choice because of lower conduction loss in the diode. The high-side MOSFET is dominated by the switching losses and it is eliminated by the soft switching technique. Additionally, the resonant auxiliary circuit designed is also devoid of the switching losses. The suggested procedure ensures an efficient converter. Theoretical analysis, computer simulation, and experimental results are presented to explain the proposed schemes.
Abstract: We prove detailed analysis of a waveguide-based Schottky barrier photodetector (SBPD) where a thin silicide film is put on the top of a silicon-on-insulator (SOI) channel waveguide to absorb light propagating along the waveguide. Taking both the confinement factor of light absorption and the wall scanning induced gain of the photoexcited carriers into account, an optimized silicide thickness is extracted to maximize the effective gain, thereby the responsivity. For typical lengths of the thin silicide film (10-20 Ðçm), the optimized thickness is estimated to be in the range of 1-2 nm, and only about 50-80% light power is absorbed to reach the maximum responsivity. Resonant waveguide-based SBPDs are proposed, which consist of a microloop, microdisc, or microring waveguide structure to allow light multiply propagating along the circular Si waveguide beneath the thin silicide film. Simulation results suggest that such resonant waveguide-based SBPDs have much higher repsonsivity at the resonant wavelengths as compared to the straight waveguidebased detectors. Some experimental results about Si waveguide-based SBPD are also reported.
Abstract: This paper presents a microstrip meandered open
circuited stub with bandstop characteristic. The proposed structure is
designed on a high frequency laminate with dielectric constant of 4.0
and board thickness of 0.508 millimeters. The scattering parameters
and electromagnetic field distributions at various frequencies are
investigated by modeling the structure with three dimensional
electromagnetic simulation tool. In order to describe the resonant
and bandstop characteristic of the meandered open circuited stub, a
Smith chart as well as electric field at various frequencies and phases
is illustrated accordingly. The structure can be an alternative method
in suppressing the harmonic response of a bandpass filter.
Abstract: A numbers of important developments have led to an
increasing attractiveness for very high speed electrical machines
(either motor or generator). Specifically the increasing switching
speed of power electronics, high energy magnets, high strength
retaining materials, better high speed bearings and improvements in
design analysis are the primary drivers in a move to higher speed. The
design challenges come in the mechanical design both in terms of
strength and resonant modes and in the electromagnetic design
particularly in respect of iron losses and ac losses in the various
conducting parts including the rotor. This paper describes detailed
design work which has been done on a 50,000 rpm, 50kW permanent
magnet( PM) synchronous machine. It describes work on
electromagnetic and rotor eddy current losses using a variety of
methods including both 2D finite element analysis
Abstract: Few studies have been conducted on polymeric strip
and the behavior of soil retaining walls. This paper will present the
effect of frequency on the dynamic behavior of reinforced soil
retaining walls with polymeric strips. The frequency content
describes how the amplitude of a ground motion is distributed among
different frequencies. Since the frequency content of an earthquake
motion will strongly influence the effects of that motion, the
characterization of the motion cannot be completed without the
consideration of its frequency content. The maximum axial force of
reinforcements and horizontal displacement of the reinforced walls
are focused in this research. To clarify the dynamic behavior of
reinforced soil retaining walls with polymeric strips, a numerical
modeling using Finite Difference Method is benefited. As the results
indicate, the frequency of input base acceleration has an important
effect on the behavior of these structures. Because of resonant in the
system, where the frequency of the input dynamic load is equal to the
natural frequency of the system, the maximum horizontal
displacement and the maximum axial forces in polymeric strips is
occurred. Moreover, they were to increase the structure flexibility
because of the main advantages of polymeric strips; i.e. being simple
method of construction, having a homogeneous behavior with soils,
and possessing long durability, which are of great importance in
dynamic analysis.
Abstract: This paper proposes a resonant dc link in PWM ac
chopper. This can solve the spike problems and also reduce the
switching loss. The configuration and PWM pattern of the proposed
technique are presented. The simulation results are used to confirm
the theory.
Abstract: In this paper we present a new multichannel high
voltage driver box to connect up to six MOEMS mirror devices to it that have resonant and also quasistatically driven actuating electrodes. It is possible to drive all resonant axes synchronously
while the amplitude of them can individually be controlled by separate microcontrollers that also operate the quasistatic axes.
Circuit simulations are compared with the measurements done on the
real system and also show the robust driving performance of a
MOEMS mirror.
Abstract: Single-pole switching scheme is widely used in the
Extra High Voltage system. However, the substantial negativesequence
current injected to the turbine-generators imposes the
electromagnetic (E/M) torque of double system- frequency
components during the dead time (between single-pole clearing and
line reclosing). This would induce supersynchronous resonance
(SPSR) torque amplifications on low pressure turbine generator
blades and even lead to fatigue damage. This paper proposes the
design of a mechanical filter (MF) with natural frequency close to
double-system frequency. From the simulation results, it is found that
such a filter not only successfully damps the resonant effect, but also
has the characteristics of feasibility and compact.