Abstract: Motion capture devices have been utilized in
producing several contents, such as movies and video games. However,
since motion capture devices are expensive and inconvenient to use,
motions segmented from captured data was recycled and synthesized
to utilize it in another contents, but the motions were generally
segmented by contents producers in manual. Therefore, automatic
motion segmentation is recently getting a lot of attentions. Previous
approaches are divided into on-line and off-line, where on-line
approaches segment motions based on similarities between
neighboring frames and off-line approaches segment motions by
capturing the global characteristics in feature space. In this paper, we
propose a graph-based high-level motion segmentation method. Since
high-level motions consist of several repeated frames within temporal
distances, we consider all similarities among all frames within the
temporal distance. This is achieved by constructing a graph, where
each vertex represents a frame and the edges between the frames are
weighted by their similarity. Then, normalized cuts algorithm is used
to partition the constructed graph into several sub-graphs by globally
finding minimum cuts. In the experiments, the results using the
proposed method showed better performance than PCA-based method
in on-line and GMM-based method in off-line, as the proposed method
globally segment motions from the graph constructed based
similarities between neighboring frames as well as similarities among
all frames within temporal distances.
Abstract: the effects of refining and alkaline chemicals on potential of recycling bleached chemical pulp of bagasse were investigated in this study. Recycling was done until three times. Handsheet properties such as, apparent density, light scattering coefficient, tear index, burst index, breaking length, and fold number according to TAPPI standard were measured. Water retention value also was used to considering the treatments during recycling. Refining enhanced the strength of recycled pulp by increasing fiber flexibility and swelling ability, whereas by applying chemical treatment didn't observe any improvement. The morphology of recycled fiber was considered with scanning electron microscopy (SEM).
Abstract: In industrial scale of Gas to Liquid (GTL) process in
Fischer-Tropsch (FT) synthesis, a part of reactor outlet gases such as
CO2 and CH4 as side reaction products, is usually recycled. In this
study, the influence of CO2 and CH4 on the performance and
selectivity of Co-Ru/Al2O3 catalyst is investigated by injection of
these gases (0-20 vol. % of feed) to the feed stream. The effect of
temperature and feed flow rate, are also inspected. The results show
that low amounts of CO2 in the feed stream, doesn`t change the
catalyst activity significantly but increasing the amount of CO2 (more
than 10 vol. %) cause the CO conversion to decrease and the
selectivity of heavy components to increase. Methane acts as an inert
gas and doesn`t affect the catalyst performance. Increasing feed flow
rate has negative effect on both CO conversion and heavy component
selectivity. By raising the temperature, CO conversion will increase
but there are more volatile components in the product. The effect of
CO2 on the catalyst deactivation is also investigated carefully and a
mechanism is suggested to explain the negative influence of CO2 on
catalyst deactivation.
Abstract: This work addresses the problem of optimizing
completely batch water-using network with multiple contaminants
where the flow change caused by mass transfer is taken into
consideration for the first time. A mathematical technique for
optimizing water-using network is proposed based on
source-tank-sink superstructure. The task is to obtain the freshwater
usage, recycle assignments among water-using units, wastewater
discharge and a steady water-using network configuration by
following steps. Firstly, operating sequences of water-using units are
determined by time constraints. Next, superstructure is simplified by
eliminating the reuse and recycle from water-using units with
maximum concentration of key contaminants. Then, the non-linear
programming model is solved by GAMS (General Algebra Model
System) for minimum freshwater usage, maximum water recycle and
minimum wastewater discharge. Finally, numbers of operating periods
are calculated to acquire the steady network configuration. A case
study is solved to illustrate the applicability of the proposed approach.
Abstract: Nowadays due to globalization of economy and
competition environment, innovation and technology plays key role
at creation of wealth and economic growth of countries. In fact
prompt growth of practical and technologic knowledge may results in
social benefits for countries when changes into effective innovation.
Considering the importance of innovation for the development of
countries, this study addresses the radical technological innovation
introduced by nanopapers at different stages of producing paper
including stock preparation, using authorized additives, fillers and
pigments, using retention, calender, stages of producing conductive
paper, porous nanopaper and Layer by layer self-assembly. Research
results show that in coming years the jungle related products will lose
considerable portion of their market share, unless embracing radical
innovation. Although incremental innovations can make this industry
still competitive in mid-term, but to have economic growth and
competitive advantage in long term, radical innovations are
necessary. Radical innovations can lead to new products and
materials which their applications in packaging industry can produce
value added. However application of nanotechnology in this industry
can be costly, it can be done in cooperation with other industries to
make the maximum use of nanotechnology possible. Therefore this
technology can be used in all the production process resulting in the
mass production of simple and flexible papers with low cost and
special properties such as facility at shape, form, easy transportation,
light weight, recovery and recycle marketing abilities, and sealing.
Improving the resistance of the packaging materials without reducing
the performance of packaging materials enhances the quality and the
value added of packaging. Improving the cellulose at nano scale can
have considerable electron optical and magnetic effects leading to
improvement in packaging and value added. Comparing to the
specifications of thermoplastic products and ordinary papers,
nanopapers show much better performance in terms of effective
mechanical indexes such as the modulus of elasticity, tensile strength,
and strain-stress. In densities lower than 640 kgm -3, due to the
network structure of nanofibers and the balanced and randomized
distribution of NFC in flat space, these specifications will even
improve more. For nanopapers, strains are 1,4Gpa, 84Mpa and 17%,
13,3 Gpa, 214Mpa and 10% respectively. In layer by layer self
assembly method (LbL) the tensile strength of nanopaper with Tio3
particles and Sio2 and halloysite clay nanotube are 30,4 ±7.6Nm/g
and 13,6 ±0.8Nm/g and 14±0.3,3Nm/g respectively that fall within
acceptable range of similar samples with virgin fiber. The usage of
improved brightness and porosity index in nanopapers can create
more competitive advantages at packaging industry.
Abstract: This research studied about green logistics and the
expected benefit that organization gotten when adapted to green
logistics also the organization concerned about the important activity
in green logistics to apply in implementation from study was found
that the benefit of green logistics that organization was gotten by
logistics management which was the increased efficiency process of
management the product from producer to customer all of reduce
production cost, increased value added save energy and prevented
environment together
From study was found that the organization had green logistics to
apply in logistics activities in supply chain since downstream till
upstream to prevent environment as follow 1). Purchasing process,
trade facilitation enhance such as linking of information technology
during business to business (B2B business). 2). Productions process
improved by business logistics improvement 3). Warehouse
management process such as recycled packaging, moving goods in to
warehouse, transportation goods and inside receiving and delivery
products plan.
Abstract: This research studied recycled waste by the Recyclable Material Bank Project of 4 universities in the central region of Thailand for the evaluation of reducing greenhouse gas emissions compared with landfilling activity during July 2012 to June 2013. The results showed that the projects collected total amount of recyclable wastes of about 911,984.80 kilograms. Office paper had the largest amount among these recycled wastes (50.68% of total recycled waste). Groups of recycled waste can be prioritized from high to low according to their amount as paper, plastic, glass, mixed recyclables, and metal, respectively. The project reduced greenhouse gas emissions equivalent to about 2814.969 metric tons of carbon dioxide. The most significant recycled waste that affects the reduction of greenhouse gas emissions is office paper which is 70.16% of total reduced greenhouse gasses emission. According to amount of reduced greenhouse gasses emission, groups of recycled waste can be prioritized from high to low significances as paper, plastic, metals, mixed recyclables, and glass, respectively.
Abstract: Climate change and environmental pressures are
major international issues nowadays. It is time when governments,
businesses and consumers have to respond through more
environmentally friendly and aware practices, products and policies.
This is the prime time to develop alternative sustainable construction
materials, reduce greenhouse gas emissions, save energy, look to
renewable energy sources and recycled materials, and reduce waste.
The utilization of waste materials (slag, fly ash, glass beads, plastic
and so on) in concrete manufacturing is significant due to its
engineering, financial, environmental and ecological benefits. Thus,
utilization of waste materials in concrete production is very much
helpful to reach the goal of the sustainable construction. Therefore,
this study intends to use glass beads in concrete production.
The paper reports on the performance of 9 different concrete
mixes containing different ratios of glass crushed to 5 mm - 20 mm
maximum size and glass marble of 20 mm size as coarse aggregate.
Ordinary Portland cement type 1 and fine sand less than 0.5 mm were
used to produce standard concrete cylinders. Compressive strength
tests were carried out on concrete specimens at various ages. Test
results indicated that the mix having the balanced ratio of glass beads
and round marbles possess maximum compressive strength which is
3889 psi, as glass beads perform better in bond formation but have
lower strength, on the other hand marbles are strong in themselves
but not good in bonding. These mixes were prepared following a
specific W/C and aggregate ratio; more strength can be expected to
achieve from different W/C, aggregate ratios, adding admixtures like
strength increasing agents, ASR inhibitor agents etc.
Abstract: In this study two series of self compacting concrete
mixtures were prepared with 100% coarse recycled concrete
aggregates and different percentages of 0%, 20%, 40%, 60%, 80%
and 100% fine recycled concrete aggregates. In series I and II the
water to binder ratios were 0.50 and 0.45, respectively. The cement
content was kept 350
3 m
kg for those mixtures that don't have any
Nano-Silica. To improve the compressive strength of samples, Nano-
Silica replaced with 10% of cement weight in concrete mixtures. By
doing the tests, the results showed that, adding Nano-silica to the
samples with less percentage of fine recycled concrete aggregates,
lead to more increase on the compressive strength.
Abstract: The problem of wastewater treatment in Egypt is a two-fold problem; the first part concerning the existing rural areas, the second one dealing with new industrial/domestic areas. In Egypt several agricultural projects have been initiated by the government and the private sector as well, in order to change its infrastructure. As a reliable energy source, photovoltaic pumping systems have contributed to supply water for local rural communities worldwide; they can also be implemented to solve the problem “wastewater environment pollution". The solution of this problem can be categorised as recycle process. In addition, because of regional conditions past technologies are being reexamined to select a smallscale treatment system requiring low construction and maintenance costs. This paper gives the design guidelines of a Photovoltaic Small- Scale Wastewater Treatment Plant (PVSSWTP) based on technologies that can be transferred.
Abstract: This paper presented a novel combined cycle of air separation and natural gas liquefaction. The idea is that natural gas can be liquefied, meanwhile gaseous or liquid nitrogen and oxygen are produced in one combined cryogenic system. Cycle simulation and exergy analysis were performed to evaluate the process and thereby reveal the influence of the crucial parameter, i.e., flow rate ratio through two stages expanders β on heat transfer temperature difference, its distribution and consequent exergy loss. Composite curves for the combined hot streams (feeding natural gas and recycled nitrogen) and the cold stream showed the degree of optimization available in this process if appropriate β was designed. The results indicated that increasing β reduces temperature difference and exergy loss in heat exchange process. However, the maximum limit value of β should be confined in terms of minimum temperature difference proposed in heat exchanger design standard and heat exchanger size. The optimal βopt under different operation conditions corresponding to the required minimum temperature differences was investigated.
Abstract: There has been a growing interest in utilizing surfactants in remediation processes to separate the hydrophobic volatile organic compounds (HVOCs) from aqueous solution. One attractive process is cloud point extraction (CPE), which utilizes nonionic surfactants as a separating agent. Since the surfactant cost is a key determination of the economic viability of the process, it is important that the surfactants are recycled and reused. This work aims to study the performance of the co-current vacuum stripping using a packed column for HVOCs removal from contaminated surfactant solution. Six types HVOCs are selected as contaminants. The studied surfactant is the branched secondary alcohol ethoxylates (AEs), Tergitol TMN-6 (C14H30O2). The volatility and the solubility of HVOCs in surfactant system are determined in terms of an apparent Henry’s law constant and a solubilization constant, respectively. Moreover, the HVOCs removal efficiency of vacuum stripping column is assessed in terms of percentage of HVOCs removal and the overall liquid phase volumetric mass transfer coefficient. The apparent Henry’s law constant of benzenz , toluene, and ethyl benzene were 7.00×10-5, 5.38×10-5, 3.35× 10-5 respectively. The solubilization constant of benzene, toluene, and ethyl benzene were 1.71, 2.68, 7.54 respectively. The HVOCs removal for all solute were around 90 percent.
Abstract: A green design for assembly model is presented to
integrate design evaluation and assembly and disassembly sequence
planning by evaluating the three activities in one integrated model. For
an assembled product, an assembly sequence planning model is
required for assembling the product at the start of the product life cycle.
A disassembly sequence planning model is needed for disassembling
the product at the end. In a green product life cycle, it is important to
plan how a product can be disassembled, reused, or recycled, before
the product is actually assembled and produced. Given a product
requirement, there may be several design alternative cases to design
the same product. In the different design cases, the assembly and
disassembly sequences for producing the product can be different. In
this research, a new model is presented to concurrently evaluate the
design and plan the assembly and disassembly sequences. First, the
components are represented by using graph based models. Next, a
particle swarm optimization (PSO) method with a new encoding
scheme is developed. In the new PSO encoding scheme, a particle is
represented by a position matrix defining an assembly sequence and a
disassembly sequence. The assembly and disassembly sequences can
be simultaneously planned with an objective of minimizing the total of
assembly costs and disassembly costs. The test results show that the
presented method is feasible and efficient for solving the integrated
design evaluation and assembly and disassembly sequence planning
problem. An example product is implemented and illustrated in this
paper.
Abstract: The upgrading of low quality crude natural gas (NG) is attracting interest due to high demand of pipeline-grade gas in recent years. Membrane processes are commercially proven technology for the removal of impurities like carbon dioxide from NG. In this work, cross flow mathematical model has been suggested to be incorporated with ASPEN HYSYS as a user defined unit operation in order to design the membrane system for CO2/CH4 separation. The effect of operating conditions (such as feed composition and pressure) and membrane selectivity on the design parameters (methane recovery and total membrane area required for the separation) has been studied for different design configurations. These configurations include single stage (with and without recycle) and double stage membrane systems (with and without permeate or retentate recycle). It is shown that methane recovery can be improved by recycling permeate or retentate stream as well as by using double stage membrane systems. The ASPEN HYSYS user defined unit operation proposed in the study has potential to be applied for complex membrane system design and optimization.
Abstract: Synthetic juice clarification was done through spiral
wound ultrafiltration (UF) membrane module. Synthetic juice was
clarified at two different operating conditions, such as, with and
without permeates recycle at turbulent flow regime. The performance
of spiral wound ultrafiltration membrane was analyzed during
clarification of synthetic juice. Synthetic juice was the mixture of
deionized water, sucrose and pectin molecule. The operating
conditions are: feed flowrate of 10 lpm, pressure drop of 413.7 kPa
and Reynolds no of 5000. Permeate sample was analyzed in terms of
volume reduction factor (VRF), viscosity (Pa.s), ⁰Brix, TDS (mg/l),
electrical conductivity (μS) and turbidity (NTU). It was observe that
the permeate flux declined with operating time for both conditions of
with and without permeate recycle due to increase of concentration
polarization and increase of gel layer on membrane surface. For
without permeate recycle, the membrane fouling rate was faster
compared to with permeate recycle. For without permeate recycle,
the VRF rose up to 5 and for with recycle permeate the VRF is 1.9.
The VRF is higher due to adsorption of solute (pectin) molecule on
membrane surface and resulting permeateflux declined with VRF.
With permeate recycle, quality was within acceptable limit. Fouled
membrane was cleaned by applying different processes (e.g.,
deionized water, SDS and EDTA solution). Membrane cleaning was
analyzed in terms of permeability recovery.
Abstract: In recent years demolished concrete waste handling and management is the new primary challenging issue faced by the countries all over the world. It is very challenging and hectic problem that has to be tackled in an indigenous manner, it is desirable to completely recycle demolished concrete waste in order to protect natural resources and reduce environmental pollution. In this research paper an experimental study is carried out to investigate the feasibility and recycling of demolished waste concrete for new construction. The present investigation to be focused on recycling demolished waste materials in order to reduce construction cost and resolving housing problems faced by the low income communities of the world. The crushed demolished concrete wastes is segregated by sieving to obtain required sizes of aggregate, several tests were conducted to determine the aggregate properties before recycling it into new concrete. This research shows that the recycled aggregate that are obtained from site make good quality concrete. The compressive strength test results of partial replacement and full recycled aggregate concrete and are found to be higher than the compressive strength of normal concrete with new aggregate.
Abstract: As the resources for naturally occurring aggregates
diminished at an ever increasing rate, researchers are keen to utilize
recycled materials in road construction in harmony with sustainable
development. Steel slag, a waste product from the steel making
industry, is one of the recycled materials reported to exhibit great
potential to replace naturally occurring aggregates in asphalt
mixtures. This paper presents the resilient modulus properties of
steel slag asphalt mixtures subjected to short term oven ageing
(STOA). The resilient modulus test was carried out to evaluate the
stiffness of asphalt mixtures at 10ºC, 25ºC and 40ºC. Previous
studies showed that stiffness changes in asphalt mixture played an
important role in inflicting pavement distress particularly cracking
and rutting that are common at low and high temperatures
respectively. Temperature was found to significantly influence the
resilient modulus of asphalt mixes. The resilient modulus of the
asphalt specimens tested decreased by more than 90% when the test
temperature increased from 10°C to 40°C.
Abstract: The recycling of concrete, bricks and masonry rubble
as concrete aggregates is an important way to contribute to a
sustainable material flow. However, there are still various
uncertainties limiting the widespread use of Recycled Concrete
Aggregates (RCA). The fluctuations in the composition of grade
recycled aggregates and their influence on the properties of fresh and
hardened concrete are of particular concern regarding the use of
RCA. Most of problems occurring while using recycled concrete
aggregates as aggregates are due to higher porosity and hence higher
water absorption, lower mechanical strengths, residual impurities on
the surface of the RCA forming weaker bond between cement paste
and aggregate. So, the reuse of RCA is still limited. Efficient
polymer based treatment is proposed in order to reuse RCA easier.
The silicon-based polymer treatments of RCA were carried out and
were compared. This kind of treatment can improve the properties of
RCA such as the rate of water absorption on treated RCA is
significantly reduced.
Abstract: This paper reports on the influence of surface-treated coarse recycled concrete aggregate (RCA) on developing the compressive strength of concrete. The coarse RCA was initially treated by separately impregnating it in calcium metasilicate (CM) or wollastonite and nanosilica (NS) prepared at various concentrations. The effects of both treatment materials on concrete properties (e.g., slump, density and compressive strength) were evaluated. Scanning electron microscopy (SEM) analysis was performed to examine the microstructure of the resulting concrete. Results show that the effective use of treated coarse RCA significantly enhances the compressive strength of concrete. This result is supported by the SEM analysis, which indicates the formation of a dense interface between the treated coarse RCA and the cement matrix. Coarse RCA impregnated in CM solution results in better concrete strength than NS, and the optimum concentration of CM solution recommended for treated coarse RCA is 10%.
Abstract: Recycling of aluminum alloys often decrease fluidity,
consequently influence the castability of the alloy. In this study, the
fluidity of Al-Zn alloys, such as the standard A713 alloy with and
without scrap addition has been investigated. The scrap added was
comprised of contaminated alloy turning chips. Fluidity
measurements were performed with double spiral fluidity test
consisting of gravity casting of double spirals in green sand moulds
with good reproducibility. The influence of recycled alloy on fluidity
has been compared with that of the virgin alloy and the results
showed that the fluidity decreased with the increase in recycled alloy
at minimum pouring temperatures. Interestingly, an appreciable
improvement in the fluidity was observed at maximum pouring
temperature, especially for coated spirals.