Abstract: A solar dish collector has been designed, fabricated
and tested for its performance on 10-03-2015 in Salem, Tamilnadu,
India. The experiments on cooking vessels of coated and un-coated
with 5 Liters capacity have been used for cooking Rice. The results
are shown in graphs. The solar cooker is always capable of cooking
food within the expected length of time and based on the solar
radiation levels. With minimum cooking power, the coated pressure
cooker of 5 Liters capacity cooks the food at faster manner. This is
due to the conductivity of the coating material provided in the cooker.
Abstract: The development of transport systems has negative
impacts on the environment although it has beneficial effects on
society. The car policy caused many problems such as: - the
spectacular growth of fuel consumption hence the very vast increase
in urban pollution, traffic congestion in certain places and at certain
times, the increase in the number of accidents. The exhaust emissions
from cars and weather conditions are the main factors that determine
the level of pollution in urban atmosphere. These conditions lead to
the phenomenon of heat transfer and radiation occurring between the
air and the soil surface of any town. These exchanges give rise, in
urban areas, to the effects of heat islands that correspond to the
appearance of excess air temperature between the city and its
surrounding space. In this object, we perform a numerical simulation
of the plume generated by the cars exhaust gases and show that these
gases form a screening effect above the urban city which cause the
heat island in the presence of wind flow. This study allows us: 1. To
understand the different mechanisms of interactions between these
phenomena.2. To consider appropriate technical solutions to mitigate
the effects of the heat island.
Abstract: The microstrip antennas area has seen some inventive
work in recent years and is now one of the most dynamic fields of
antenna theory. A novel and simple wideband monopole antenna is
presented printed on a single dielectric substrate which is fed by a 50
ohm microstrip line having a low-profile antenna structure with two
parallel s-shaped meandered line of same size. This antenna is fed by
a coaxial feeding tube. In this research, S–form microstrip patch antenna is designed from
measuring the prototypes of the proposed antenna one available
bands with 10db return loss bandwidths of about GPS application
(GPS L2 1490 MHz) and covering the 1400 to 1580 MHz frequency
band at 1.5 GHz, the simulated results for main parameters such as
return loss, impedance bandwidth, radiation patterns, and gains are
also discussed herein. The modeling study shows that such antennas,
in simplicity design and supply, can satisfy GPS application. Two
parallel slots are incorporated to disturb the surface flow path,
introducing local inductive effect. This antenna is fed by a coaxial
feeding tube.
Abstract: In this communication, a low-cost circularly
polarized wire antenna exhibiting improved gain performance for
Dedicated Short Range Communications (DSRC), vehicle-to-vehicle
(V2V) and vehicle-to-infrastructure (V2I) communications is
presented. The proposed antenna comprises a Y-shaped quarterwavelength
monopole antenna surrounded by two iterations of eight
conductive arched walls acting as parasitic elements to enhance the
overall antenna gain and to shape the radiation pattern in the H-plane.
A hemispherical radome shell is added to protect the antenna
structure and its effect on the antenna performance is discussed. The
designed antenna demonstrates antenna gain of 8.2 dB with
omnidirectional far-field radiation pattern in the H-plane. The gain of
the proposed antenna is also compared with the characteristic of the
stand-alone Y-shaped monopole to highlight the advantages of the
proposed approach.
Abstract: Greenhouses offer us suitable conditions which can
be controlled easily for the growth of the plant and they are made by
using a covering material that allows the sun light entering into the
system. Covering material can be glass, fiber glass, plastic or another
transparent element. This study investigates the solar energy usability
rates and solar energy benefitting rates of a semi-spherical (modified
arch) type greenhouse system according to different orientations and
positions which exists under climatic conditions of Bayburt. In the
concept of this study it is tried to determine the best direction and
best sizes of a semi-spherical greenhouse to get best solar benefit
from the sun. To achieve this aim a modeling study is made by using
MATLAB. However, this modeling study is run for some determined
shapes and greenhouses it can be used for different shaped
greenhouses or buildings. The basic parameters are determined as
greenhouse azimuth angle, the rate of size of long edge to short and
seasonal solar energy gaining of greenhouse. The optimum azimuth
angles of 400, 300, 250, 200, 150, 100, 50 m2 modified arch
greenhouse are 90o, 90o, 35o, 35o, 34o, 33o and 22o while their
optimum k values (ratio of length to width) are 10, 10, 10, 10, 6, 4
and 4 respectively. Positioning the buildings in order to get more
solar heat energy in winter and less in summer brings out energy and
money savings and increases the comfort.
Abstract: Si ion implantation was widely used to synthesize
specimens of SiO2 containing supersaturated Si and subsequent high
temperature annealing induces the formation of embedded
luminescent Si nanocrystals. In this work, the potentialities of excimer
UV-light (172 nm, 7.2 eV) irradiation and rapid thermal annealing
(RTA) to enhance the photoluminescence and to achieve low
temperature formation of Si nanocrystals have been investigated. The
Si ions were introduced at acceleration energy of 180 keV to fluence of
7.5 x 1016 ions/cm2. The implanted samples were subsequently
irradiated with an excimer-UV lamp. After the process, the samples
were rapidly thermal annealed before furnace annealing (FA).
Photoluminescence spectra were measured at various stages at the
process. We found that the luminescence intensity is strongly
enhanced with excimer-UV irradiation and RTA. Moreover, effective
visible photoluminescence is found to be observed even after FA at
900 oC, only for specimens treated with excimer-UV lamp and RTA.
We also prepared specimens of Si nanocrystals embedded in a SiO2 by
reactive pulsed laser deposition (PLD) in an oxygen atmosphere. We
will make clear the similarities and differences with the way of
preparation.
Abstract: Let us consider that the entire universe is composed of
a single hydrogen atom within which the electron is moving around
the proton. In this case, according to classical theories of physics,
radiation, photons respectively, should be absorbed by the electron.
Depending on the number of photons absorbed, the electron radius of
rotation around the proton is established. Until now, the principle of
photons absorption by electrons and the electron transition to a new
energy level, namely to a higher radius of rotation around the proton,
is not clarified in physics. This paper aims to demonstrate that
radiation, photons respectively, have mass and negative electrostatic
charge similar to electrons but infinitely smaller. The experiments
which demonstrate this theory are simple: thermal expansion,
photoelectric effect and thermonuclear reaction.
Abstract: Evapotranspiration is one of the most important
components of the hydrological cycle. Evapotranspiration (ETo) is an
important variable in water and energy balances on the earth’s
surface, and knowledge of the distribution of ET is a key factor in
hydrology, climatology, agronomy and ecology studies. Many
researchers have a valid relationship, which is a function of climate
factors, to estimate the potential evapotranspiration presented to the
plant water stress or water loss, prevent. The FAO-Penman method
(PM) had been recommended as a standard method. This method
requires many data and these data are not available in every area of
world. So, other methods should be evaluated for these conditions.
When sufficient or reliable data to solve the PM equation are not
available then Hargreaves equation can be used. The Hargreaves
equation (HG) requires only daily mean, maximum and minimum air
temperature extraterrestrial radiation .In this study, Hargreaves
method (HG) were evaluated in 12 stations in the North West region
of Iran. Results of HG and M.HG methods were compared with
results of PM method. Statistical analysis of this comparison showed
that calibration process has had significant effect on efficiency of
Hargreaves method.
Abstract: This paper presents development results of usage of
C-OTDR monitoring systems for rail traffic management. The COTDR
method is based on vibrosensitive properties of optical fibers.
Analysis of Rayleigh backscattering radiation parameters changes
which take place due to microscopic seismoacoustic impacts on the
optical fiber allows to determine seismoacoustic emission source
positions and to identify their types. This approach proved successful
for rail traffic management (moving block system, weigh- in-motion
system etc.).
Abstract: The aim of this investigation is to elaborate nearinfrared
methods for testing and recognition of chemical components
and quality in “Pannon wheat” allied (i.e. true to variety or variety
identified) milling fractions as well as to develop spectroscopic
methods following the milling processes and evaluate the stability of
the milling technology by different types of milling products and
according to sampling times, respectively. These wheat categories
produced under industrial conditions where samples were collected
versus sampling time and maximum or minimum yields. The changes
of the main chemical components (such as starch, protein, lipid) and
physical properties of fractions (particle size) were analysed by
dispersive spectrophotometers using visible (VIS) and near-infrared
(NIR) regions of the electromagnetic radiation. Close correlation
were obtained between the data of spectroscopic measurement
techniques processed by various chemometric methods (e.g. principal
component analysis [PCA], cluster analysis [CA]) and operation
condition of milling technology. It is obvious that NIR methods are
able to detect the deviation of the yield parameters and differences of
the sampling times by a wide variety of fractions, respectively. NIR
technology can be used in the sensitive monitoring of milling
technology.
Abstract: A compound parabolic concentrator (CPC) is a wellknown
non-imaging concentrator that will concentrate the solar
radiation onto receiver (PV cell). One of disadvantage of CPC is has
tall and narrow height compared to its diameter entry aperture area.
Therefore, for economic reason, a truncation had been done by
removed from the top of the full height CPC. This also will lead to
the decreases of concentration ratio but it will be negligible. In this
paper, the flux distribution of untruncated and truncated 2-D hollow
compound parabolic trough concentrator (hCPTC) design is
presented. The untruncated design has initial height H=193.4mm
with concentration ratio C_(2-D)=4. This paper presents the optical
simulation of compound parabolic trough concentrator using raytracing
software TracePro. Results showed that, after the truncation,
the height of CPC reduced 45% from initial height with the
geometrical concentration ratio only decrease 10%. Thus, the cost of
reflector and material dielectric usage can be saved especially at
manufacturing site.
Abstract: The comprehensive CFD models have been used to
represent and study the heterogeneous combustion of biomass. In the
present work, the operation of a global flue gas circuit in the sugarcane
bagasse combustion, from wind boxes below primary air grate
supply, passing by bagasse insertion in swirl burners and boiler
furnace, to boiler bank outlet is simulated. It uses five different
meshes representing each part of this system located in sequence:
wind boxes and grate, boiler furnace, swirl burners, superheaters and
boiler bank. The model considers turbulence using standard k-ε,
combustion using EDM, radiation heat transfer using DTM with 16
ray directions and bagasse particle tracking represented by Schiller-
Naumann model. The results showed good agreement with expected
behavior found in literature and equipment design. The more detailed
results view in separated parts of flue gas system allows observing
some flow behaviors that cannot be represented by usual
simplifications like bagasse supply under homogeneous axial and
rotational vectors and others that can be represented using new
considerations like the representation of 26 thousand grate orifices by
144 rectangular inlets.
Abstract: Microstructural and hardening changes of
Fe-0.2wt.%V alloy and pure Fe irradiated with 100 keV hydrogen ions
at room temperature were investigated. It was found that dislocation
density varies dramatically after irradiation, ranging from dislocation
free to dense areas with tangled and complex dislocation
configuration. As the irradiated Fe-0.2wt.%V samples were annealed
at 773 K, the irradiation-induced dislocation loops disappear, while
many small precipitates with enriched C distribute in the matrix. Some
large precipitates with enriched V were also observed. The hardness of
Fe-0.2wt.%V alloy and pure Fe increases after irradiation, which
ascribes to the formation of dislocation loops in the irradiated
specimens. Compared with pure Fe, the size of the
irradiation-introduced dislocation loops in Fe-0.2wt.%V alloy
decreases and the density increases, the change of the hardness also
decreases.
Abstract: Many industrial materials like magnets need to be
tested for the radiation environment expected at linear colliders (LC)
where the accelerator and detectors will be subjected to large
influences of beta, neutron and gamma’s over their life Gamma
irradiation of the permanent sample magnets using a 60Co source was
investigated up to an absorbed dose of 700Mrad shows a negligible
effect on some magnetic properties of Nd-Fe-B. In this work it has
been tried to investigate the change of some important properties of
Barium hexa ferrite. Results showed little decreases of magnetic
properties at doses rang of 0.5 to 2.5 Mrad. But at the gamma
irradiation dose up to 10 Mrad it is showed a few increase of
properties. Also study of gamma irradiation of Nd-Fe-B showed
considerably increase of magnetic properties.
Abstract: The changes of the optical and structural properties of
Bismuth-Boro-Tellurite glasses pre and post gamma irradiation were
studied. Six glass samples, with different composition [(TeO2)0.7
(B2O3)0.3]1-x (Bi2O3)x prepared by melt quenching method were
irradiated with 25kGy gamma radiation at room temperature. The
Fourier Transform Infrared Spectroscopy (FTIR) was used to explore
the structural bonding in the prepared glass samples due to exposure,
while UV-VIS Spectrophotometer was used to evaluate the changes
in the optical properties before and after irradiation. Gamma
irradiation causes profound changes in the peak intensity as shown by
FTIR spectra which is due to the breaking of the network bonding.
Before gamma irradiation, the optical band gap, Eg value decreased
from 2.44 eV to 2.15 eV with the addition of Bismuth content. The
value kept decreasing (from 2.18 eV to 2.00 eV) following exposure
to gamma radiation due to the increase of non-bridging oxygen
(NBO) and the increase of defect in the glass. In conclusion, the glass
with high content of Bi2O3 (0.30Bi) give smallest Eg and show less
changes in FTIR spectra after gamma irradiation which indicate that
this glass is more resistant to gamma radiation compared to other
glasses.
Abstract: A comprehensive CFD model is developed to
represent heterogeneous combustion and two burner designs of
supply sugar-cane bagasse into a furnace. The objective of this work
is to compare the insertion and burning of a Brazilian south-eastern
sugar-cane bagasse using a new swirl burner design against an actual
geometry under operation. The new design allows control the
particles penetration and scattering inside furnace by adjustment of
axial/tangential contributions of air feed without change their mass
flow. The model considers turbulence using RNG k-, combustion
using EDM, radiation heat transfer using DTM with 16 ray directions
and bagasse particle tracking represented by Schiller-Naumann
model. The obtained results are favorable to use of new design swirl
burner because its axial/tangential control promotes more penetration
or more scattering than actual design and allows reproduce the actual
design operation without change the overall mass flow supply.
Abstract: In this study, we proposed two techniques to track the
maximum power point (MPPT) of a photovoltaic system. The first is
an intelligent control technique, and the second is robust used for
variable structure system. In fact the characteristics I-V and P–V of
the photovoltaic generator depends on the solar irradiance and
temperature. These climate changes cause the fluctuation of
maximum power point; a maximum power point tracking technique
(MPPT) is required to maximize the output power. For this we have
adopted a control by fuzzy logic (FLC) famous for its stability and
robustness. And a Siding Mode Control (SMC) widely used for
variable structure system. The system comprises a photovoltaic panel
(PV), a DC-DC converter, which is considered as an adaptation stage
between the PV and the load. The modelling and simulation of the
system is developed using MATLAB/Simulink. SMC technique
provides a good tracking speed in fast changing irradiation and when
the irradiation changes slowly or it is constant the panel power of
FLC technique presents a much smoother signal with less
fluctuations.
Abstract: Pipa is one of the most important Chinese traditional
plucked instruments, but its directivity has never been measured
systematically. In western, directivity of loudness for western
instruments is deeply researched through analysis of sound pressure
level, whereas the directivity of timbre is seldom studied. In this paper,
a new method for directivity of timbre was proposed, and horizontal
directivity patterns of loudness and timbre of Pipa were measured.
Directivity of Pipa radiation was measured in an anechoic room. The
sound of Pipa played by a musician was recorded simultaneously by
32 microphones with Pipa in the center. The measuring results were
examined through listening test. According to the measurement of
Pipa directivity radiation, we put forward the best localization of Pipa
in the Chinese traditional orchestra and the optimal recording region.
Abstract: Cesium iodide (CsI) melt was injected into anodic aluminum oxide (AAO) template and was solidified to CsI column. The controllable AAO channel size (10~500 nm) can makes CsI column size from 10 to 500 nm in diameter. In order to have a shorter light irradiate from each singe CsI column top to bottom the AAO template was coated a TiO2 nano-film. The TiO2 film acts a refraction film and makes X-ray has a shorter irradiation path in the CsI crystal making a stronger the photo-electron signal. When the incidence light irradiate from air (R=1.0) to CsI’s first surface (R=1.84) the first refraction happen, the first refraction continue into TiO2 film (R=2.88) and produces the low angle of the second refraction. Then the second refraction continue into AAO wall (R=1.78) and produces the third refraction after refractions between CsI and AAO wall (R=1.78) produce the fourth refraction. The incidence light through TiO2 filmand the first surface of CsI then arrive to the second surface of CsI. Therefore, the TiO2 film can has shorter refraction path of incidence light and increase the photo-electron conversion efficiency.
Abstract: Optical radiation emitted from a metal-coated fiber tip apex at liquid-air interface was measured. The intensity of the output radiation was strongly depend on the relative position of the tip to a liquid-air interface and varied with surface fluctuations. This phenomenon permits in-situ real-time investigation of nano-metric vibrations of the liquid surface and provides a basis for development of various origin ultrasensitive vibration detecting sensors. The described method can be used for detection of week seismic vibrations.