Abstract: Orthogonal Frequency Division Multiplexing (OFDM) is one of the techniques for high speed data rate communication with main consideration for 4G and 5G systems. In OFDM, there are several mapping schemes which provide a way of parallel transmission. In this paper, comparisons of mapping schemes used by some standards have been made and also has been discussed about the performance of the non-conventional modulation technique. The Comparisons of Bit Error Rate (BER) performances for conventional and non-conventional modulation schemes have been done using MATLAB software. Mentioned schemes used in OFDM system can be selected on the basis of the requirement of power or spectrum efficiency and BER analysis.
Abstract: This paper presents a method for obtaining the
desired reference current for Voltage Source Converter (VSC) of the Shunt Active Power Filter (SAPF) using Synchronous Reference Frame Theory. The method relies on the performance of the Proportional-Integral (PI) controller for
obtaining the best control performance of the SAPF. To
improve the performance of the PI controller, the feedback
path to the integral term is introduced to compensate the
winding up phenomenon due to integrator. Using Reference
Frame Transformation, reference signals are transformed from
a - b - c stationery frame to 0 - d - q rotating frame.
Using the PI controller, the reference signals in the 0 - d - q rotating frame are controlled to get the desired reference signals for the Pulse Width Modulation. The synchronizer, the Phase Locked Loop (PLL) with PI filter is used for
synchronization, with much emphasis on minimizing delays. The system performance is examined with Shunt Active Power Filter simulation model.
Abstract: This paper presents a novel three-phase utility
frequency to high frequency soft switching power conversion circuit
with dual mode pulse width modulation and pulse density modulation
for high power induction heating applications as melting of steel and
non ferrous metals, annealing of metals, surface hardening of steel
and cast iron work pieces and hot water producers, steamers and
super heated steamers. This high frequency power conversion circuit
can operate from three-phase systems to produce high current for
high power induction heating applications under the principles of
ZVS and it can regulate its ac output power from the rated value to a
low power level. A dual mode modulation control scheme based on
high frequency PWM in synchronization with the utility frequency
positive and negative half cycles for the proposed high frequency
conversion circuit and utility frequency pulse density modulation is
produced to extend its soft switching operating range for wide ac
output power regulation. A dual packs heat exchanger assembly is
designed to be used in consumer and industrial fluid pipeline systems
and it is proved to be suitable for the hot water, steam and super
heated steam producers. Experiment and simulation results are given
in this paper to verify the operation principles of the proposed ac
conversion circuit and to evaluate its power regulation and
conversion efficiency. Also, the paper presents a mutual coupling
model of the induction heating load instead of equivalent transformer
circuit model.
Abstract: DC-DC converters are widely used in regulated switched mode power supplies and in DC motor drive applications. There are several sources of unwanted nonlinearity in practical power converters. In addition, their operation is characterized by switching that gives birth to a variety of nonlinear dynamics. DC-DC buck and boost converters controlled by pulse-width modulation (PWM) have been simulated. The voltage waveforms and attractors obtained from the circuit simulation have been studied. With the onset of instability, the phenomenon of subharmonic oscillations, quasi-periodicity, bifurcations, and chaos have been observed. This paper is mainly motivated by potential contributions of chaos theory in the design, analysis and control of power converters, in particular and power electronics circuits, in general.
Abstract: Application of neural networks in execution of
programmed pulse width modulation (PPWM) of a voltage source
inverter (VSI) is studied in this paper. Using the proposed method it is
possible to cancel out the desired harmonics in output of VSI in
addition to control the magnitude of fundamental harmonic,
contineously. By checking the non-trained values and a performance
index, the most appropriate neural network is proposed. It is shown
that neural networks may solve the custom difficulties of practical
utilization of PPWM such as large size of memory, complex digital
circuits and controlling the magnitude of output voltage in a discrete
manner.
Abstract: In this paper, a joint source-channel coding (JSCC) scheme for time-varying channels is presented. The proposed scheme uses hierarchical framework for both source encoder and transmission via QAM modulation. Hierarchical joint source channel codes with hierarchical QAM constellations are designed to track the channel variations which yields to a higher throughput by adapting certain parameters of the receiver to the channel variation. We consider the problem of still image transmission over time-varying channels with channel state information (CSI) available at 1) receiver only and 2) both transmitter and receiver being informed about the state of the channel. We describe an algorithm that optimizes hierarchical source codebooks by minimizing the distortion due to source quantizer and channel impairments. Simulation results, based on image representation, show that, the proposed hierarchical system outperforms the conventional schemes based on a single-modulator and channel optimized source coding.
Abstract: Pulse code modulation is a widespread technique
in digital communication with significant impact on existing
modern and proposed future communication technologies. Its
widespread utilization is due to its simplicity and attractive
spectral characteristics. In this paper, we present a new
approach to the spectral analysis of PCM signals using
Riemann-Stieltjes integrals, which is very accurate for high bit
rates. This approach can serve as a model for similar spectral
analysis of other competing modulation schemes.
Abstract: Radio propagation from point-to-point is affected by
the physical channel in many ways. A signal arriving at a destination
travels through a number of different paths which are referred to as
multi-paths. Research in this area of wireless communications has
progressed well over the years with the research taking different
angles of focus. By this is meant that some researchers focus on
ways of reducing or eluding Multipath effects whilst others focus on
ways of mitigating the effects of Multipath through compensation
schemes. Baseband processing is seen as one field of signal
processing that is cardinal to the advancement of software defined
radio technology. This has led to wide research into the carrying out
certain algorithms at baseband. This paper considers compensating
for Multipath for Frequency Modulated signals. The compensation
process is carried out at Radio frequency (RF) and at Quadrature
baseband (QBB) and the results are compared. Simulations are
carried out using MatLab so as to show the benefits of working at
lower QBB frequencies than at RF.
Abstract: The Object of this paper is to design and analyze a
Hysteresis modulation based sliding mode control (HMSMC) for
positive output elementary super lift Luo converter (POESLLC),
which is the start-of-the-art DC-DC converter. The positive output
elementary super lift Luo converter performs the voltage
conversion from positive source voltage to positive load voltage.
This paper proposes a HMSMC capable of providing the good
steady state and dynamic performance compared to conventional
controllers. Dynamic equations describing the positive output
elementary super lift luo converter are derived by using state space
average method. The simulation model of the positive output
elementary super lift Luo converter with its control circuit is
implemented in Matlab/Simulink. The HMSMC for positive
output elementary super lift Luo converter is tested for line
changes, load changes and also for components variations.
Abstract: Reduced switching loss favours Pulse Skipping
Modulation mode of switching dc-to-dc converters at light loads.
Under certain conditions the converter operates in discontinuous
conduction mode (DCM). Inductor current starts from zero in each
switching cycle as the switching frequency is constant and not
adequately high. A DC-to-DC buck converter is modelled and
simulated in this paper under DCM. Effect of ESR of the filter
capacitor in input current frequency components is studied. The
converter is studied for its operation under input voltage and load
variation. The operating frequency is selected to be close to and
above audio range.
Abstract: This paper proposes a feed-forward control in
resonant dc link inverter. The feed-forward control configuration is
based on synchronous sigma-delta modulation. The simulation
results showing the proposed technique can reject non-ideal dc bus
improving the total harmonic distortion.
Abstract: In order to achieve better road utilization and traffic
efficiency, there is an urgent need for a travel information delivery
mechanism to assist the drivers in making better decisions in the
emerging intelligent transportation system applications. In this paper,
we propose a relayed multicast scheme under heterogeneous networks
for this purpose. In the proposed system, travel information consisting
of summarized traffic conditions, important events, real-time traffic
videos, and local information service contents is formed into layers
and multicasted through an integration of WiMAX infrastructure and
Vehicular Ad hoc Networks (VANET). By the support of adaptive
modulation and coding in WiMAX, the radio resources can be
optimally allocated when performing multicast so as to dynamically
adjust the number of data layers received by the users. In addition to
multicast supported by WiMAX, a knowledge propagation and
information relay scheme by VANET is designed. The experimental
results validate the feasibility and effectiveness of the proposed
scheme.
Abstract: The neural stimulation has been gaining much interest in neuromodulation research and clinical trials. For efficiency, there is a need for variable electrical stimulation such as current and voltage stimuli as well as wireless framework. In this regard, we develop the wireless neural stimulator capable of voltage and current stimuli. The system consists of ZigBee which is a wireless communication module and stimulus generator. The stimulus generator with 8-bits resolution enable both mono-polar and bi-polar waveform in voltage (-3.3~3.3V) and current(-330~330µA) stimulus mode which is controllable. The experimental results suggest that the proposed neural stimulator can play a role as an effective approach for neuromodulation.
Abstract: The increasing demand for higher data rates in wireless communication systems has led to the more effective and efficient use of all allocated frequency bands. In order to use the whole bandwidth at maximum efficiency, one needs to have RF power amplifiers with a higher linear level and memory-less performance. This is considered to be a major challenge to circuit designers. In this thesis the linearity and memory are studied and examined via the behavior of the intermodulation distortion (IMD). A major source of the in-band distortion can be shown to be influenced by the out-of-band impedances presented at either the input or the output of the device, especially those impedances terminated the low frequency (IF) components. Thus, in order to regulate the in-band distortion, the out of-band distortion must be controllable. These investigations are performed on a 12W LDMOS device characterised at 2.1 GHz within a purpose built, high-power measurement system.
Abstract: This paper explores the implementation of adaptive
coding and modulation schemes for Multiple-Input Multiple-Output
Orthogonal Frequency Division Multiplexing (MIMO-OFDM) feedback
systems. Adaptive coding and modulation enables robust and
spectrally-efficient transmission over time-varying channels. The basic
premise is to estimate the channel at the receiver and feed this estimate
back to the transmitter, so that the transmission scheme can be
adapted relative to the channel characteristics. Two types of codebook
based channel feedback techniques are used in this work. The longterm
and short-term CSI at the transmitter is used for efficient channel
utilization. OFDM is a powerful technique employed in communication
systems suffering from frequency selectivity. Combined with
multiple antennas at the transmitter and receiver, OFDM proves to be
robust against delay spread. Moreover, it leads to significant data rates
with improved bit error performance over links having only a single
antenna at both the transmitter and receiver. The coded modulation
increases the effective transmit power relative to uncoded variablerate
variable-power MQAM performance for MIMO-OFDM feedback
system. Hence proposed arrangement becomes an attractive approach
to achieve enhanced spectral efficiency and improved error rate
performance for next generation high speed wireless communication
systems.
Abstract: This paper study the high-level modelling and design
of delta-sigma (ΔΣ) noise shapers for audio Digital-to-Analog
Converter (DAC) so as to eliminate the in-band Signal-to-Noise-
Ratio (SNR) degradation that accompany one channel mismatch in
audio signal. The converter combines a cascaded digital signal
interpolation, a noise-shaping single loop delta-sigma modulator with
a 5-bit quantizer resolution in the final stage. To reduce sensitivity of
Digital-to-Analog Converter (DAC) nonlinearities of the last stage, a
high pass second order Data Weighted Averaging (R2DWA) is
introduced. This paper presents a MATLAB description modelling
approach of the proposed DAC architecture with low distortion and
swing suppression integrator designs. The ΔΣ Modulator design can
be configured as a 3rd-order and allows 24-bit PCM at sampling rate
of 64 kHz for Digital Video Disc (DVD) audio application. The
modeling approach provides 139.38 dB of dynamic range for a 32
kHz signal band at -1.6 dBFS input signal level.
Abstract: This paper presented a theoretical and numerical investigation of the Compact Antenna Test Range (CATR) equipped with Super Hybrid Modulated Segmented Exponential Serrations (SHMSES). The investigation was based on diffraction theory and, more specifically, the Fresnel diffraction formulation. The CATR provides uniform illumination within the Fresnel region to test antenna. Application of serrated edges has been shown to be a good method to control diffraction at the edges of the reflectors. However, in order to get some insight into the positive effect of serrated edges a less rigorous analysis technique known as Physical Optics (PO) may be used. Ripple free and enhanced quiet zone width are observed for specific values of width and height modulation factors per serrations. The performance of SHMSE serrated reflector is evaluated in order to observe the effects of edge diffraction on the test zone fields.
Abstract: Evolution of one-dimensional electron system under
high-energy-density (HED) conditions is investigated, using the
principle of least-action and variational method. In a single-mode
modulation model, the amplitude and spatial wavelength of the
modulation are chosen to be general coordinates. Equations of motion
are derived by considering energy conservation and force balance.
Numerical results show that under HED conditions, electron density
modulation could exist. Time dependences of amplitude and
wavelength are both positively related to the rate of energy input.
Besides, initial loading speed has a significant effect on modulation
amplitude, while wavelength relies more on loading duration.
Abstract: The study of soil for agriculture purposes has
remained the main focus of research since the beginning of civilization as humans- food related requirements remained closely linked with the soil. The study of soil has generated an interest
among the researchers for very similar other reasons including transmission, reflection and refraction of signals for deploying
wireless underground sensor networks or for the monitoring of objects on (or in ) soil in the form of better understanding of soil
electromagnetic characteristics properties. The moisture content has
been very instrumental in such studies as it decides on the resistance of the soil, and hence the attenuation on signals traveling through soil
or the attenuation the signals may suffer upon their impact on soil. This work is related testing and characterizing a measurement circuit
meant for the detection of moisture level content in soil.
Abstract: To make the modulation classification system more suitable for signals in a wide range of signal to noise rate (SNR), a novel method of designing combined classifier based on fuzzy neural network (FNN) is presented in this paper. The method employs fuzzy neural network classifiers and interclass distance (ICD) to improve recognition reliability. Experimental results show that the proposed combined classifier has high recognition rate with large variation range of SNR (success rates are over 99.9% when SNR is not lower than 5dB).