Abstract: Routing places an important role in determining the
quality of service in wireless networks. The routing methods adopted
in wireless networks have many drawbacks. This paper aims to
review the current routing methods used in wireless networks. This
paper proposes an innovative solution to overcome the problems in
routing. This solution is aimed at improving the Quality of Service.
This solution is different from others as it involves the resuage of the
part of the virtual circuits. This improvement in quality of service is
important especially in propagation of multimedia applications like
video, animations etc. So it is the dire need to propose a new solution
to improve the quality of service in ATM wireless networks for
multimedia applications especially during this era of multimedia
based applications.
Abstract: Public health surveillance system focuses on outbreak detection and data sources used. Variation or aberration in the frequency distribution of health data, compared to historical data is often used to detect outbreaks. It is important that new techniques be developed to improve the detection rate, thereby reducing wastage of resources in public health. Thus, the objective is to developed technique by applying frequent mining and outlier mining techniques in outbreak detection. 14 datasets from the UCI were tested on the proposed technique. The performance of the effectiveness for each technique was measured by t-test. The overall performance shows that DTK can be used to detect outlier within frequent dataset. In conclusion the outbreak detection technique using anomaly-based on frequent-outlier technique can be used to identify the outlier within frequent dataset.
Abstract: Undoubtedly, chassis is one of the most important
parts of a vehicle. Chassis that today are produced for vehicles are
made up of four parts. These parts are jointed together by screwing.
Transverse parts are called cross member.
This study reviews the stress generated by cyclic laboratory loads
in front cross member of Peugeot 405. In this paper the finite element
method is used to simulate the welding process and to determine the
physical response of the spot-welded joints. Analysis is done by the
Abaqus software.
The Stresses generated in cross member structure are generally
classified into two groups: The stresses remained in form of residual
stresses after welding process and the mechanical stress generated by
cyclic load. Accordingly the total stress must be obtained by
determining residual stress and mechanical stress separately and then
sum them according to the superposition principle.
In order to improve accuracy, material properties including
physical, thermal and mechanical properties were supposed to be
temperature-dependent. Simulation shows that maximum Von Misses
stresses are located at special points. The model results are then
compared to the experimental results which are reported by
producing factory and good agreement is observed.
Abstract: In projects like waterpower, transportation and
mining, etc., proving up the rock-mass structure and hidden tectonic
to estimate the geological body-s activity is very important.
Integrating the seismic results, drilling and trenching data,
CSAMT method was carried out at a planning dame site in southwest
China to evaluate the stability of a deformation. 2D and imitated 3D
inversion resistivity results of CSAMT method were analyzed. The
results indicated that CSAMT was an effective method for defining
an outline of deformation body to several hundred meters deep; the
Lung Pan Deformation was stable in natural conditions; but uncertain
after the future reservoir was impounded.
This research presents a good case study of the fine surveying and
research on complex geological structure and hidden tectonic in
engineering project.
Abstract: In the last few years, three multivariate spectral
analysis techniques namely, Principal Component Analysis (PCA),
Independent Component Analysis (ICA) and Non-negative Matrix
Factorization (NMF) have emerged as effective tools for oscillation
detection and isolation. While the first method is used in determining
the number of oscillatory sources, the latter two methods
are used to identify source signatures by formulating the detection
problem as a source identification problem in the spectral domain.
In this paper, we present a critical drawback of the underlying linear
(mixing) model which strongly limits the ability of the associated
source separation methods to determine the number of sources
and/or identify the physical source signatures. It is shown that the
assumed mixing model is only valid if each unit of the process gives
equal weighting (all-pass filter) to all oscillatory components in its
inputs. This is in contrast to the fact that each unit, in general, acts
as a filter with non-uniform frequency response. Thus, the model
can only facilitate correct identification of a source with a single
frequency component, which is again unrealistic. To overcome
this deficiency, an iterative post-processing algorithm that correctly
identifies the physical source(s) is developed. An additional issue
with the existing methods is that they lack a procedure to pre-screen
non-oscillatory/noisy measurements which obscure the identification
of oscillatory sources. In this regard, a pre-screening procedure
is prescribed based on the notion of sparseness index to eliminate
the noisy and non-oscillatory measurements from the data set used
for analysis.
Abstract: The paper makes part from a complex research project
on Romanian Grey Steppe, a unique breed in terms of biological and
cultural-historical importance, on the verge of extinction and which
has been included in a preservation programme of genetic resources
from Romania. The study of genetic polymorphism of protean
fractions, especially kappa-casein, and the genotype relations of
these lactoproteins with some quantitative and qualitative features of
milk yield represents a current theme and a novelty for this breed. In
the estimation of the genetic parameters we used R.E.M.L.
(Restricted Maximum Likelihood) method.
The main lactoprotein from milk, kappa - casein (K-cz),
characterized in the specialized literature as a feature having a high
degree of hereditary transmission, behaves as such in the nucleus under
study, a value also confirmed by the heritability coefficient (h2 = 0.57
%). We must mention the medium values for milk and fat quantity
(h2=0.26, 0.29 %) and the fat and protein percentage from milk
having a high hereditary influence h2 = 0.71 - 0.63 %.
Correlations between kappa-casein and the milk quantity are
negative and strong. Between kappa-casein and other qualitative
features of milk (fat content 0.58-0.67 % and protein content 0.77-
0.87%), there are positive and very strong correlations. At the same
time, between kappa-casein and β casein (β-cz), β lactoglobulin (β-
lg) respectively, correlations are positive having high values (0.37 –
0.45 %), indicating the same causes and determining factors for the
two groups of features.
Abstract: A dynamic stall-corrected Blade Element-Momentum algorithm based on a hybrid polar is validated through the comparison with Sandia experimental measurements on a 5-m diameter wind turbine of Troposkien shape. Different dynamic stall models are evaluated. The numerical predictions obtained using the extended aerodynamic coefficients provided by both Sheldal and Klimas and Raciti Castelli et al. are compared to experimental data, determining the potential of the hybrid database for the numerical prediction of vertical-axis wind turbine performances.
Abstract: This paper investigates the inverse problem of determining
the unknown time-dependent leading coefficient in the parabolic
equation using the usual conditions of the direct problem and an additional
condition. An algorithm is developed for solving numerically
the inverse problem using the technique of space decomposition in a
reproducing kernel space. The leading coefficients can be solved by a
lower triangular linear system. Numerical experiments are presented
to show the efficiency of the proposed methods.