Abstract: This paper presents the performance characteristics of
Darrieus-type vertical axis wind turbine (VAWT) with NACA airfoil
blades. The performance of Darrieus-type VAWT can be
characterized by torque and power. There are various parameters
affecting the performance such as chord length, helical angle, pitch
angle and rotor diameter. To estimate the optimum shape of Darrieustype
wind turbine in accordance with various design parameters, we
examined aerodynamic characteristics and separated flow occurring
in the vicinity of blade, interaction between flow and blade, and
torque and power characteristics derived from it. For flow analysis,
flow variations were investigated based on the unsteady RANS
(Reynolds-averaged Navier-Stokes) equation. Sliding mesh algorithm
was employed in order to consider rotational effect of blade. To
obtain more realistic results we conducted experiment and numerical
analysis at the same time for three-dimensional shape. In addition,
several parameters (chord length, rotor diameter, pitch angle, and
helical angle) were considered to find out optimum shape design and
characteristics of interaction with ambient flow. Since the NACA
airfoil used in this study showed significant changes in magnitude of
lift and drag depending on an angle of attack, the rotor with low drag,
long cord length and short diameter shows high power coefficient in
low tip speed ratio (TSR) range. On the contrary, in high TSR range,
drag becomes high. Hence, the short-chord and long-diameter rotor
produces high power coefficient. When a pitch angle at which airfoil
directs toward inside equals to -2° and helical angle equals to 0°,
Darrieus-type VAWT generates maximum power.
Abstract: Direct Torque Control (DTC) is an AC drive control
method especially designed to provide fast and robust responses. In
this paper a progressive algorithm for direct torque control of threephase
induction drive system supplied by photovoltaic arrays using
voltage source inverter to control motor torque and flux with
maximum power point tracking at different level of insolation is
presented. Experimental results of the new DTC method obtained by
an experimental rapid prototype system for drives are presented.
Simulation and experimental results confirm that the proposed system
gives quick, robust torque and speed responses at constant switching
frequencies.
Abstract: This paper presents a model predictive control (MPC)
of a utility interactive three phase inverter (TPI) for a photovoltaic
(PV) system at commercial level. The proposed model uses phase
locked loop (PLL) to synchronize the TPI with the power electric
grid (PEG) and performs MPC control in a dq reference frame. TPI
model consists of a boost converter (BC), maximum power point
tracking (MPPT) control, and a three-leg voltage source inverter
(VSI). The operational model of VSI is used to synthesize the
sinusoidal current and track the reference. The model is validated
using a 35.7 kW PV system in Matlab/Simulink. Implementation
results show simplicity and accuracy, as well as reliability of the
model.
Abstract: This paper presents a grid synchronization technique based on adaptive notch filter for SPV (Solar Photovoltaic) system along with MPPT (Maximum Power Point Tracking) techniques. An efficient grid synchronization technique offers proficient detection of various components of grid signal like phase and frequency. It also acts as a barrier for harmonics and other disturbances in grid signal. A reference phase signal synchronized with the grid voltage is provided by the grid synchronization technique to standardize the system with grid codes and power quality standards. Hence, grid synchronization unit plays important role for grid connected SPV systems. As the output of the PV array is fluctuating in nature with the meteorological parameters like irradiance, temperature, wind etc. In order to maintain a constant DC voltage at VSC (Voltage Source Converter) input, MPPT control is required to track the maximum power point from PV array. In this work, a variable step size P & O (Perturb and Observe) MPPT technique with DC/DC boost converter has been used at first stage of the system. This algorithm divides the dPpv/dVpv curve of PV panel into three separate zones i.e. zone 0, zone 1 and zone 2. A fine value of tracking step size is used in zone 0 while zone 1 and zone 2 requires a large value of step size in order to obtain a high tracking speed. Further, adaptive notch filter based control technique is proposed for VSC in PV generation system. Adaptive notch filter (ANF) approach is used to synchronize the interfaced PV system with grid to maintain the amplitude, phase and frequency parameters as well as power quality improvement. This technique offers the compensation of harmonics current and reactive power with both linear and nonlinear loads. To maintain constant DC link voltage a PI controller is also implemented and presented in this paper. The complete system has been designed, developed and simulated using SimPower System and Simulink toolbox of MATLAB. The performance analysis of three phase grid connected solar photovoltaic system has been carried out on the basis of various parameters like PV output power, PV voltage, PV current, DC link voltage, PCC (Point of Common Coupling) voltage, grid voltage, grid current, voltage source converter current, power supplied by the voltage source converter etc. The results obtained from the proposed system are found satisfactory.
Abstract: In this study, we proposed two techniques to track the
maximum power point (MPPT) of a photovoltaic system. The first is
an intelligent control technique, and the second is robust used for
variable structure system. In fact the characteristics I-V and P–V of
the photovoltaic generator depends on the solar irradiance and
temperature. These climate changes cause the fluctuation of
maximum power point; a maximum power point tracking technique
(MPPT) is required to maximize the output power. For this we have
adopted a control by fuzzy logic (FLC) famous for its stability and
robustness. And a Siding Mode Control (SMC) widely used for
variable structure system. The system comprises a photovoltaic panel
(PV), a DC-DC converter, which is considered as an adaptation stage
between the PV and the load. The modelling and simulation of the
system is developed using MATLAB/Simulink. SMC technique
provides a good tracking speed in fast changing irradiation and when
the irradiation changes slowly or it is constant the panel power of
FLC technique presents a much smoother signal with less
fluctuations.
Abstract: The pursuit of the MPPT has led to the development of many kinds of controllers, one of which is the Fuzzy Logic controller, which has proven its worth. To further tune this controller this paper will discuss and analyze the use of Genetic Algorithms to tune the Fuzzy Logic Controller. It will provide an introduction to both systems, and test their compatibility and performance.
Abstract: Microbial fuel cells (MFCs) represent a promising
technology for simultaneous bioelectricity generation and wastewater
treatment. Catalysts are significant portions of the cost of microbial
fuel cell cathodes. Many materials have been tested as aqueous
cathodes, but air-cathodes are needed to avoid energy demands for
water aeration. The sluggish oxygen reduction reaction (ORR) rate at
air cathode necessitates efficient electrocatalyst such as carbon
supported platinum catalyst (Pt/C) which is very costly. Manganese
oxide (MnO2) was a representative metal oxide which has been
studied as a promising alternative electrocatalyst for ORR and has
been tested in air-cathode MFCs. However the single MnO2 has poor
electric conductivity and low stability. In the present work, the MnO2
catalyst has been modified by doping Pt nanoparticle. The goal of the
work was to improve the performance of the MFC with minimum Pt
loading. MnO2 and Pt nanoparticles were prepared by hydrothermal
and sol gel methods, respectively. Wet impregnation method was
used to synthesize Pt/MnO2 catalyst. The catalysts were further used
as cathode catalysts in air-cathode cubic MFCs, in which anaerobic
sludge was inoculated as biocatalysts and palm oil mill effluent
(POME) was used as the substrate in the anode chamber. The asprepared
Pt/MnO2 was characterized comprehensively through field
emission scanning electron microscope (FESEM), X-Ray diffraction
(XRD), X-ray photoelectron spectroscopy (XPS), and cyclic
voltammetry (CV) where its surface morphology, crystallinity,
oxidation state and electrochemical activity were examined,
respectively. XPS revealed Mn (IV) oxidation state and Pt (0)
nanoparticle metal, indicating the presence of MnO2 and Pt.
Morphology of Pt/MnO2 observed from FESEM shows that the
doping of Pt did not cause change in needle-like shape of MnO2
which provides large contacting surface area. The electrochemical
active area of the Pt/MnO2 catalysts has been increased from 276 to
617 m2/g with the increase in Pt loading from 0.2 to 0.8 wt%. The
CV results in O2 saturated neutral Na2SO4 solution showed that
MnO2 and Pt/MnO2 catalysts could catalyze ORR with different
catalytic activities. MFC with Pt/MnO2 (0.4 wt% Pt) as air cathode
catalyst generates a maximum power density of 165 mW/m3, which
is higher than that of MFC with MnO2 catalyst (95 mW/m3). The
open circuit voltage (OCV) of the MFC operated with MnO2 cathode
gradually decreased during 14 days of operation, whereas the MFC
with Pt/MnO2 cathode remained almost constant throughout the
operation suggesting the higher stability of the Pt/MnO2 catalyst.
Therefore, Pt/MnO2 with 0.4 wt% Pt successfully demonstrated as an
efficient and low cost electrocatalyst for ORR in air cathode MFC with higher electrochemical activity, stability and hence enhanced
performance.
Abstract: Newly synthesized Polypropylene-g-Polyethylene
glycol polymer was first time used for a compartment-less enzymatic
fuel cell. Working electrodes based on Polypropylene-g-Polyethylene
glycol were operated as unmediated and mediated system (with
ferrocene and gold/cobalt oxide nanoparticles). Glucose oxidase and
bilirubin oxidase was selected as anodic and cathodic enzyme,
respectively. Glucose was used as fuel in a single-compartment and
membrane-less cell. Maximum power density was obtained as 0.65
nW cm-2, 65 nW cm-2 and 23500 nW cm-2 from the unmediated,
ferrocene and gold/cobalt oxide modified polymeric film,
respectively. Power density was calculated to be ~16000 nW cm-2 for
undiluted wastewater sample with gold/cobalt oxide nanoparticles
including system.
Abstract: The most important component affecting the
efficiency of photovoltaic power systems are solar panels. In other
words, efficiency of these systems are significantly affected due to
the being low efficiency of solar panel. Thus, solar panels should be
operated under maximum power point conditions through a power
converter. In this study, design of boost converter has been carried
out with maximum power point tracking (MPPT) algorithm which is
incremental conductance (Inc-Cond). By using this algorithm,
importance of power converter in MPPT hardware design, impacts of
MPPT operation have been shown. It is worth noting that initial
operation point is the main criteria for determining the MPPT
performance. In addition, it is shown that if value of load resistance is
lower than critical value, failure operation is realized. For these
analyzes, direct duty control is used for simplifying the control.
Abstract: The levels of maximum power density of GSM
signals in the cities of Lagos, Ibadan and Abuja were studied.
Measurements were made with a calibrated hand held spectrum
analyzer 200m away from 271 base stations, at 1.2m to the ground
level. The maximum GSM 900 signal power density was
139.63μW/m2 in Lagos, 162.49μW/m2 in Ibadan and 5411.26μW/m2
in Abuja. Also, the maximum GSM 1800 signal power density was
296.82μW/m2 in Lagos, 116.82μW/m2 in Ibadan and 1263.00μW/m2
in Abuja. The level of power density of GSM 900 and GSM 1800
signals in the cities of Lagos, Ibadan and Abuja are far less than the
recommended value of 4.5W/m2 for GSM 900 and 9.0 W/m2 for
GSM 1800 by the ICNRP guideline. It can be concluded that
exposure to GSM signals in these cities cannot contribute to the
health detriments caused by thermal effects of radiofrequency
radiation.
Abstract: The electric power supplied by a photovoltaic power
generation systems depends on the solar irradiation and temperature.
The PV system can supply the maximum power to the load at a
particular operating point which is generally called as maximum
power point (MPP), at which the entire PV system operates with
maximum efficiency and produces its maximum power. Hence, a
Maximum power point tracking (MPPT) methods are used to
maximize the PV array output power by tracking continuously the
maximum power point. The proposed MPPT controller is designed
for 10kW solar PV system installed at Cape Institute of Technology.
This paper presents the fuzzy logic based MPPT algorithm. However,
instead of one type of membership function, different structures of
fuzzy membership functions are used in the FLC design. The
proposed controller is combined with the system and the results are
obtained for each membership functions in Matlab/Simulink
environment. Simulation results are decided that which membership
function is more suitable for this system.
Abstract: This paper presents a model predictive control (MPC)
of a utility interactive (UI) single phase inverter (SPI) for a
photovoltaic (PV) system at residential/distribution level. The
proposed model uses single-phase phase locked loop (PLL) to
synchronize SPI with the grid and performs MPC control in a dq
reference frame. SPI model consists of boost converter (BC),
maximum power point tracking (MPPT) control, and a full bridge
(FB) voltage source inverter (VSI). No PI regulators to tune and
carrier and modulating waves are required to produce switching
sequence. Instead, the operational model of VSI is used to synthesize
sinusoidal current and track the reference. Model is validated using a
three kW PV system at the input of UI-SPI in Matlab/Simulink.
Implementation and results demonstrate simplicity and accuracy, as
well as reliability of the model.
Abstract: The scope of this paper is to evaluate and compare the potential of LS-PV(Large Scale Photovoltaic Power Plant) power generation systems in the southern region of Libya at Al-Kufra for both stationary and tracking systems. A Microsoft Excel-VBA program has been developed to compute slope radiation, dew-point, sky temperature, and then cell temperature, maximum power output and module efficiency of the system for stationary system and for tracking system. The results for energy production show that the total energy output is 114GWh/year for stationary system and 148GWh/year for tracking system. The average module efficiency for the stationary system is 16.6% and 16.2% for the tracking system.
The values of electricity generation capacity factor (CF) and solar capacity factor (SCF) for stationary system were found to be 26% and 62.5% respectively and 34% and 82% for tracking system. The GCR (Ground Cover Ratio) for a stationary system is 0.7, which corresponds to a tilt angle of 24°. The GCR for tracking system was found to be 0.12. The estimated ground area needed to build a 50MW PV plant amounts to approx. 0.55km2 for a stationary PV field constituted by HIT PV arrays and approx. 91MW/ km2. In case of a tracker PV field, the required ground area amounts approx.2.4km2 and approx. 20.5MW/ km2.
Abstract: It is well known that photovoltaic (PV) cells are an attractive source of energy. Abundant and ubiquitous, this source is one of the important renewable energy sources that have been increasing worldwide year by year. However, in the V-P characteristic curve of GPV, there is a maximum point called the maximum power point (MPP) which depends closely on the variation of atmospheric conditions and the rotation of the earth. In fact, such characteristics outputs are nonlinear and change with variations of temperature and irradiation, so we need a controller named maximum power point tracker MPPT to extract the maximum power at the terminals of photovoltaic generator. In this context, the authors propose here to study the modeling of a photovoltaic system and to find an appropriate method for optimizing the operation of the PV generator using two intelligent controllers respectively to track this point. The first one is based on artificial neural networks and the second on fuzzy logic. After the conception and the integration of each controller in the global process, the performances are examined and compared through a series of simulation. These two controller have prove by their results good tracking of the MPPT compare with the other method which are proposed up to now.
Abstract: Temperature rising is a negative factor in almost all systems. It could cause by self heating or ambient temperature. In solar photovoltaic cells this temperature rising affects on the behavior of cells. The ability of a PV module to withstand the effects of periodic hot-spot heating that occurs when cells are operated under reverse biased conditions is closely related to the properties of the cell semi-conductor material.
In addition, the thermal effect also influences the estimation of the maximum power point (MPP) and electrical parameters for the PV modules, such as maximum output power, maximum conversion efficiency, internal efficiency, reliability, and lifetime. The cells junction temperature is a critical parameter that significantly affects the electrical characteristics of PV modules. For practical applications of PV modules, it is very important to accurately estimate the junction temperature of PV modules and analyze the thermal characteristics of the PV modules. Once the temperature variation is taken into account, we can then acquire a more accurate MPP for the PV modules, and the maximum utilization efficiency of the PV modules can also be further achieved.
In this paper, the three-Dimensional Transmission Line Matrix (3D-TLM) method was used to map the surface temperature distribution of solar cells while in the reverse bias mode. It was observed that some cells exhibited an inhomogeneity of the surface temperature resulting in localized heating (hot-spot). This hot-spot heating causes irreversible destruction of the solar cell structure. Hot spots can have a deleterious impact on the total solar modules if individual solar cells are heated. So, the results show clearly that the solar cells are capable of self-generating considerable amounts of heat that should be dissipated very quickly to increase PV module's lifetime.
Abstract: This paper presents a simulation and mathematical model of stand-alone solar-wind-diesel based hybrid energy system (HES). A power management system is designed for multiple energy resources in a stand-alone hybrid energy system. Both Solar photovoltaic and wind energy conversion system consists of maximum power point tracking (MPPT), voltage regulation, and basic power electronic interfaces. An additional diesel generator is included to support and improve the reliability of stand-alone system when renewable energy sources are not available. A power management strategy is introduced to distribute the generated power among resistive load banks. The frequency regulation is developed with conventional phase locked loop (PLL) system. The power management algorithm was applied in Matlab®/Simulink® to simulate the results.
Abstract: In this paper, ANN controller for maximum power point tracking of photovoltaic (PV) systems is proposed and PV modeling is discussed. Maximum power point tracking (MPPT) methods are used to maximize the PV array output power by tracking continuously the maximum power point. ANN controller with hill-climbing algorithm offers fast and accurate converging to the maximum operating point during steady-state and varying weather conditions compared to conventional hill-climbing. The proposed algorithm gives a good maximum power operation of the PV system. Simulation results obtained are presented and compared with the conventional hill-climbing algorithm. Simulation results show the effectiveness of the proposed technique.
Abstract: Since the output characteristics of photovoltaic (PV) system depends on the ambient temperature, solar radiation and load impedance, its maximum power point (MPP) is not constant. Under each condition PV module has a point at which it can produce its MPP. Therefore, a maximum power point tracking (MPPT) method is needed to uphold the PV panel operating at its MPP. This paper presents comparative study between the conventional MPPT methods used in (PV) system: Perturb and Observe (P&O), Incremental Conductance (IncCond), andParticle Swarm Optimization (PSO) algorithmfor (MPPT) of (PV) system. To evaluate the study, the proposed PSO MPPT is implemented on a DC-DC cuk converter and has been compared with P&O and INcond methods in terms of their tracking speed, accuracy and performance by using the Matlab tool Simulink. The simulation result shows that the proposed algorithm is simple, and is superior to the P&O and IncCond methods.
Abstract: Nowadays the use of Hybrid Electric Vehicles (HEV) is increasing dramatically. The HEV is mainly dependent on electricity and there is always a need for storage of charge. Fuel Cell (FC), Batteries and Ultra Capacitor are being used for the proposed HEV as an electric power source or as an energy storage unit. The aim of developing an energy management technique is to utilize the sources according to the requirement of the vehicle with help of controller. This increases the efficiency of hybrid electric vehicle to reduce the fuel consumption and unwanted emission. The Maximum Power Point Tracking (MPPT) in FC is done using (Perturb & Observe) algorithm. In this paper, the control of automobiles at variable speed is achieved effectively.
Abstract: This paper proposes an improved Maximum Power Point Tracking of PhotoVoltaic system using Deterministic Partical Swarm Optimization technique. This method has the ability to track the maximum power under varying environmental conditions i.e. partial shading conditions. The advantage of this method, particles moves in the restricted value of velocity to achieve the maximum power. SEPIC converter is employed to boost up the voltage of PV system. To estimate the value of the proposed method, MATLAB simulation carried out under partial shading condition.