Abstract: Segmentation and quantification of stenosis is an
important task in assessing coronary artery disease. One of the main
challenges is measuring the real diameter of curved vessels.
Moreover, uncertainty in segmentation of different tissues in the
narrow vessel is an important issue that affects accuracy. This paper
proposes an algorithm to extract coronary arteries and measure the
degree of stenosis. Markovian fuzzy clustering method is applied to
model uncertainty arises from partial volume effect problem. The
algorithm employs: segmentation, centreline extraction, estimation of
orthogonal plane to centreline, measurement of the degree of
stenosis. To evaluate the accuracy and reproducibility, the approach
has been applied to a vascular phantom and the results are compared
with real diameter. The results of 10 patient datasets have been
visually judged by a qualified radiologist. The results reveal the
superiority of the proposed method compared to the Conventional
thresholding Method (CTM) on both datasets.
Abstract: This paper proposes the stochastic tabu search (STS)
for improving the measurement scheme for power system state
estimation. If the original measured scheme is not observable, the
additional measurements with minimum number of measurements are
added into the system by STS so that there is no critical measurement
pair. The random bit flipping and bit exchanging perturbations are
used for generating the neighborhood solutions in STS. The Pδ
observable concept is used to determine the network observability.
Test results of 10 bus, IEEE 14 and 30 bus systems are shown that
STS can improve the original measured scheme to be observable
without critical measurement pair. Moreover, the results of STS are
superior to deterministic tabu search (DTS) in terms of the best
solution hit.
Abstract: Array signal processing involves signal enumeration and source localization. Array signal processing is centered on the ability to fuse temporal and spatial information captured via sampling signals emitted from a number of sources at the sensors of an array in order to carry out a specific estimation task: source characteristics (mainly localization of the sources) and/or array characteristics (mainly array geometry) estimation. Array signal processing is a part of signal processing that uses sensors organized in patterns or arrays, to detect signals and to determine information about them. Beamforming is a general signal processing technique used to control the directionality of the reception or transmission of a signal. Using Beamforming we can direct the majority of signal energy we receive from a group of array. Multiple signal classification (MUSIC) is a highly popular eigenstructure-based estimation method of direction of arrival (DOA) with high resolution. This Paper enumerates the effect of missing sensors in DOA estimation. The accuracy of the MUSIC-based DOA estimation is degraded significantly both by the effects of the missing sensors among the receiving array elements and the unequal channel gain and phase errors of the receiver.
Abstract: This paper introduces a technique of distortion
estimation in image watermarking using Genetic Programming (GP).
The distortion is estimated by considering the problem of obtaining a
distorted watermarked signal from the original watermarked signal as
a function regression problem. This function regression problem is
solved using GP, where the original watermarked signal is
considered as an independent variable. GP-based distortion
estimation scheme is checked for Gaussian attack and Jpeg
compression attack. We have used Gaussian attacks of different
strengths by changing the standard deviation. JPEG compression
attack is also varied by adding various distortions. Experimental
results demonstrate that the proposed technique is able to detect the
watermark even in the case of strong distortions and is more robust
against attacks.
Abstract: The rapid growth of e-Commerce services is
significantly observed in the past decade. However, the method to
verify the authenticated users still widely depends on numeric
approaches. A new search on other verification methods suitable for
online e-Commerce is an interesting issue. In this paper, a new online
signature-verification method using angular transformation is
presented. Delay shifts existing in online signatures are estimated by
the estimation method relying on angle representation. In the
proposed signature-verification algorithm, all components of input
signature are extracted by considering the discontinuous break points
on the stream of angular values. Then the estimated delay shift is
captured by comparing with the selected reference signature and the
error matching can be computed as a main feature used for verifying
process. The threshold offsets are calculated by two types of error
characteristics of the signature verification problem, False Rejection
Rate (FRR) and False Acceptance Rate (FAR). The level of these two
error rates depends on the decision threshold chosen whose value is
such as to realize the Equal Error Rate (EER; FAR = FRR). The
experimental results show that through the simple programming,
employed on Internet for demonstrating e-Commerce services, the
proposed method can provide 95.39% correct verifications and 7%
better than DP matching based signature-verification method. In
addition, the signature verification with extracting components
provides more reliable results than using a whole decision making.
Abstract: The Carrier Frequency Offset (CFO) due to timevarying
fading channel is the main cause of the loss of orthogonality
among OFDM subcarriers which is linked to inter-carrier interference
(ICI). Hence, it is necessary to precisely estimate and compensate the
CFO. Especially for mobile broadband communications, CFO and
channel gain also have to be estimated and tracked to maintain the
system performance. Thus, synchronization pilots are embedded in
every OFDM symbol to track the variations. In this paper, we present
the pilot scheme for both channel and CFO estimation where channel
estimation process can be carried out with only one OFDM symbol.
Additional, the proposed pilot scheme also provides better
performance in CFO estimation comparing with the conventional
orthogonal pilot scheme due to the increasing of signal-tointerference
ratio.
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and quasistationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine first stage nozzle blade.
Abstract: Diatoms are an important group of aquatic ecosystems and diatom-based indices are increasingly becoming important tools for the assessment of ecological conditions in lotic systems. Although the studies are very limited about Turkish rivers, diatom indices were used for monitoring rivers in different basins. In the present study, we used OMNIDIA program for estimation of stream quality. Some indices have less sensitive (IDP, WAT, LOBO, GENRE, TID, CEE, PT), intermediate sensitivities (IDSE, DESCY, IPS, DI-CH, SLA, IDAP), the others higher sensitivities (SID, IBD, SHE, EPI-D). Among the investigated diatom communities, only a few taxa indicated alfa-mesosaprobity and polysaprobity. Most of the sites were characterized by a great relative contribution of eutraphent and tolerant ones as well as oligosaprobic and betamesosaprobic diatoms. In general, SID and IBD indices gave the best results. This study suggests that the structure of benthic diatom communities and diatom indices, especially SID, can be applied for monitoring rivers in Southern Turkey.
Abstract: In this paper, a fast motion compensation algorithm is
proposed that improves coding efficiency for video sequences with
brightness variations. We also propose a cross entropy measure
between histograms of two frames to detect brightness variations. The
framewise brightness variation parameters, a multiplier and an offset
field for image intensity, are estimated and compensated. Simulation
results show that the proposed method yields a higher peak signal to
noise ratio (PSNR) compared with the conventional method, with a
greatly reduced computational load, when the video scene contains
illumination changes.
Abstract: Modern manufacturing facilities are large scale,
highly complex, and operate with large number of variables under
closed loop control. Early and accurate fault detection and diagnosis
for these plants can minimise down time, increase the safety of plant
operations, and reduce manufacturing costs. Fault detection and
isolation is more complex particularly in the case of the faulty analog
control systems. Analog control systems are not equipped with
monitoring function where the process parameters are continually
visualised. In this situation, It is very difficult to find the relationship
between the fault importance and its consequences on the product
failure. We consider in this paper an approach to fault detection and
analysis of its effect on the production quality using an adaptive
centring and scaling in the pickling process in cold rolling. The fault
appeared on one of the power unit driving a rotary machine, this
machine can not track a reference speed given by another machine.
The length of metal loop is then in continuous oscillation, this affects
the product quality. Using a computerised data acquisition system,
the main machine parameters have been monitored. The fault has
been detected and isolated on basis of analysis of monitored data.
Normal and faulty situation have been obtained by an artificial neural
network (ANN) model which is implemented to simulate the normal
and faulty status of rotary machine. Correlation between the product
quality defined by an index and the residual is used to quality
classification.
Abstract: This article presents a short discussion on
optimum neighborhood size selection in a spherical selforganizing
feature map (SOFM). A majority of the literature
on the SOFMs have addressed the issue of selecting optimal
learning parameters in the case of Cartesian topology SOFMs.
However, the use of a Spherical SOFM suggested that the
learning aspects of Cartesian topology SOFM are not directly
translated. This article presents an approach on how to
estimate the neighborhood size of a spherical SOFM based on
the data. It adopts the L-curve criterion, previously suggested
for choosing the regularization parameter on problems of
linear equations where their right-hand-side is contaminated
with noise. Simulation results are presented on two artificial
4D data sets of the coupled Hénon-Ikeda map.
Abstract: Video watermarking is usually considered as watermarking of a set of still images. In frame-by-frame watermarking approach, each video frame is seen as a single watermarked image, so collusion attack is more critical in video watermarking. If the same or redundant watermark is used for embedding in every frame of video, the watermark can be estimated and then removed by watermark estimate remodolulation (WER) attack. Also if uncorrelated watermarks are used for every frame, these watermarks can be washed out with frame temporal filtering (FTF). Switching watermark system or so-called SS-N system has better performance against WER and FTF attacks. In this system, for each frame, the watermark is randomly picked up from a finite pool of watermark patterns. At first SS-N system will be surveyed and then a new collusion attack for SS-N system will be proposed using a new algorithm for separating video frame based on watermark pattern. So N sets will be built in which every set contains frames carrying the same watermark. After that, using WER attack in every set, N different watermark patterns will be estimated and removed later.
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and quasi-stationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine first stage nozzle blade.
Abstract: Thermal load calculations have been performed for
multi-layered walls that are composed of three different parts; a
common (sand and cement) plaster, and two types of locally
produced soft and hard bricks. The masonry construction of these
layered walls was based on concrete-backed stone masonry made of
limestone bricks joined by mortar. These multilayered walls are
forming the outer walls of the building envelope of a typical Libyan
house. Based on the periodic seasonal weather conditions, within the
Libyan cost region during summer and winter, measured thermal
conductivity values were used to implement such seasonal variation
of heat flow and the temperature variations through the walls. The
experimental measured thermal conductivity values were obtained
using the Hot Disk technique. The estimation of the thermal
resistance of the wall layers ( R-values) is based on measurements
and calculations. The numerical calculations were done using a
simplified analytical model that considers two different wall
constructions which are characteristics of such houses. According to
the obtained results, the R-values were quite low and therefore,
several suggestions have been proposed to improve the thermal
loading performance that will lead to a reasonable human comfort
and reduce energy consumption.
Abstract: In areas of low to moderate seismicity many building contents and equipment are not positively fixed to the floor or tied to adjacent walls. Under seismic induced horizontal vibration, such contents and equipment can suffer from damage by either overturning or impact associated with rocking. This paper focuses on the estimation of shock on typical contents and equipment due to rocking. A simplified analytical model is outlined that can be used to estimate the maximum acceleration on a rocking object given its basic geometric and mechanical properties. The developed model was validated against experimental results. The experimental results revealed that the maximum shock acceleration can be underestimated if the static stiffness of the materials at the interface between the rocking object and floor is used rather than the dynamic stiffness. Excellent agreement between the model and experimental results was found when the dynamic stiffness for the interface material was used, which was found to be generally much higher than corresponding static stiffness under different investigated boundary conditions of the cushion. The proposed model can be a beneficial tool in performing a rapid assessment of shock sensitive components considered for possible seismic rectification.
Abstract: From a set of shifted, blurred, and decimated image , super-resolution image reconstruction can get a high-resolution image. So it has become an active research branch in the field of image restoration. In general, super-resolution image restoration is an ill-posed problem. Prior knowledge about the image can be combined to make the problem well-posed, which contributes to some regularization methods. In the regularization methods at present, however, regularization parameter was selected by experience in some cases and other techniques have too heavy computation cost for computing the parameter. In this paper, we construct a new super-resolution algorithm by transforming the solving of the System stem Є=An into the solving of the equations X+A*X-1A=I , and propose an inverse iterative method.
Abstract: Self-sensing estimates the air gap within an electro
magnetic path by analyzing the bearing coil current and/or voltage
waveform. The self-sensing concept presented in this paper has been
developed within the research project “Active Magnetic Bearings
with Supreme Reliability" and is used for position sensor fault
detection.
Within this new concept gap calculation is carried out by an alldigital
analysis of the digitized coil current and voltage waveform.
For analysis those time periods within the PWM period are used,
which give the best results. Additionally, the concept allows the
digital compensation of nonlinearities, for example magnetic
saturation, without degrading signal quality. This increases the
accuracy and robustness of the air gap estimation and additionally
reduces phase delays.
Beneath an overview about the developed concept first
measurement results are presented which show the potential of this
all-digital self-sensing concept.
Abstract: This paper presents an evaluation of the wind potential in the area of the Lagoon of Venice (Italy). A full anemometric campaign of 2 year measurements, performed by the "Osservatorio Bioclimatologico dell'Ospedale al Mare di Venezia" has been analyzed to obtain the Weibull wind speed distribution and the main wind directions. The annual energy outputs of two candidate horizontal-axis wind turbines (“Aventa AV-7 LoWind" and “Gaia Wind 133-11kW") have been estimated on the basis of the computed Weibull wind distribution, registering a better performance of the former turbine, due to a higher ratio between rotor swept area and rated power of the electric generator, determining a lower cut-in wind speed.
Abstract: A two-dimensional numerical simulation of the contribution
of both inertial and aerodynamic forces on the blade loads of
a Vertical-Axis Wind Turbine (VAWT) is presented. After describing
the computational model and the relative validation procedure, a
complete campaign of simulations - based on full RANS unsteady
calculations - is proposed for a three-bladed rotor architecture characterized
by a NACA 0021 airfoil. For each analyzed angular velocity,
the combined effect of pressure and viscous forces acting on every
rotor blade are compared to the corresponding centrifugal forces,
due to the revolution of the turbine, thus achieving a preliminary
estimation of the correlation between overall rotor efficiency and
structural blade loads.
Abstract: Air conditioning is mainly use as human comfort
cooling medium. It use more in high temperatures are country such as
Malaysia. Proper estimation of cooling load will archive ideal
temperature. Without proper estimation can lead to over estimation or
under estimation. The ideal temperature should be comfort enough.
This study is to develop a program to calculate an ideal cooling load
demand, which is match with heat gain. Through this study, it is easy
to calculate cooling load estimation. Objective of this study are to
develop user-friendly and easy excess cooling load program. This is
to insure the cooling load can be estimate by any of the individual
rather than them using rule-of-thumb. Developed software is carryout
by using Matlab-GUI. These developments are only valid for
common building in Malaysia only. An office building was select as
case study to verify the applicable and accuracy of develop software.
In conclusion, the main objective has successfully where developed
software is user friendly and easily to estimate cooling load demand.