Abstract: The global energy consumption is increasing persistently and need for distributed power generation through renewable energy is essential. To meet the power requirements for consumers without any voltage fluctuations and losses, modeling and design of multilevel inverter with Flexible AC Transmission System (FACTS) capability is presented. The presented inverter is provided with 13-level cascaded H-bridge topology of Insulated Gate Bipolar Transistor (IGBTs) connected along with inbuilt Distributed Static Synchronous Compensators (DSTATCOM). The DSTATCOM device provides control of power factor stability at local feeder lines and the inverter eliminates Total Harmonic Distortion (THD). The 13-level inverter utilizes 52 switches of each H-bridge is fed with single DC sources separately and the Pulse Width Modulation (PWM) technique is used for switching IGBTs. The control strategy implemented for inverter transmits active power to grid as well as it maintains power factor to be stable with achievement of steady state power transmission. Significant outcome of this project is improvement of output voltage quality with steady state power transmission with low THD. Simulation of inverter with DSTATCOM is performed using MATLAB/Simulink environment. The scaled prototype model of proposed inverter is built and its results were validated with simulated results.
Abstract: This paper investigates the problem of blind speech separation from the speech mixture of two speakers. A voice activity detector employing the Steered Response Power - Phase Transform (SRP-PHAT) is presented for detecting the activity information of speech sources and then the desired speech signals are extracted from the speech mixture by using an optimal beamformer. For evaluation, the algorithm effectiveness, a simulation using real speech recordings had been performed in a double-talk situation where two speakers are active all the time. Evaluations show that the proposed blind speech separation algorithm offers a good interference suppression level whilst maintaining a low distortion level of the desired signal.
Abstract: Industrial drives are source of serious power quality problems. In this, two typical industrial drives have been dealt with, namely, FOC induction motor drives and DTC induction motor drive. The Z-source inverter is an emerging topology of power electronic converters which is capable of buck boost characteristics. The performances of different control methods based Z-source inverters feeding these industrial drives have been investigated, in this work. The test systems have been modeled and simulated in MATLAB/SIMULINK. The results obtained after carrying out these simulations have been used to draw the conclusions.
Abstract: The morphotropic phase boundary (MPB) recently has attracted constant interest in ferromagnetic systems for obtaining enhanced large magnetoelastic response. In the present study, structural and magnetoelastic properties of MPB involved ferromagnetic Tb1-xGdxFe2 (0≤x≤1) system has been investigated. The change of easy magnetic direction from to with increasing x up MPB composition of x=0.9 is detected by step-scanned [440] synchrotron X-ray diffraction reflections. The Gd substitution for Tb changes the composition for the anisotropy compensation near MPB composition of x=0.9, which was confirmed by the analysis of detailed scanned XRD, magnetization curves and the calculation of the first anisotropy constant K1. The spin configuration diagram accompanied with different crystal structures for Tb1-xGdxFe2 was designed. The calculated first anisotropy constant K1 shows a minimum value at MPB composition of x=0.9. In addition, the large ratio between magnetostriction, and the absolute values of the first anisotropy constant │λS∕K1│ appears at MPB composition, which makes it a potential material for magnetostrictive application. Based on experimental results, a theoretically approach was also proposed to signify that the facilitated magnetization rotation and enhanced magnetoelastic effect near MPB composition are a consequence of the anisotropic flattening of free energy of ferromagnetic crystal. Our work specifies the universal existence of MPB in ferromagnetic materials which is important for substantial improvement of magnetic and magnetostrictive properties and may provide a new route to develop advanced functional materials.
Abstract: The technology of mobile telephony has positively enhanced human life and reports on the bio safety of the radiation from their antennae have been contradictory, leading to serious litigations and violent protests by residents in several parts of the world. The crave for more information, as requested by WHO in order to resolve this issue, formed the basis for this study on the effect of the radiation from 900 MHz GSM antenna on the DNA of Hibiscus sabdariffa. Seeds of H. sabdariffa were raised in pots placed in three replicates at 100, 200, 300 and 400 metres from the GSM antennae in three selected test locations and a control where there was no GSM signal. Temperature (˚C) and the relative humidity (%) of study sites were measured for the period of study (24 weeks). Fresh young leaves were harvested from each plant at two, eight and twenty-four weeks after sowing and the DNA extracts were subjected to RAPD-PCR analyses. There were no significant differences between the weather conditions (temperature and relative humidity) in all the study locations. However, significant differences were observed in the intensities of radiations between the control (less than 0.02 V/m) and the test (0.40-1.01 V/m) locations. Data obtained showed that DNA of samples exposed to rays from GSM antenna had various levels of distortions, estimated at 91.67%. Distortions occurred in 58.33% of the samples between 2-8 weeks of exposure while 33.33% of the samples were distorted between 8-24 weeks exposure. Approximately 8.33% of the samples did not show distortions in DNA while 33.33% of the samples had their DNA damaged twice, both at 8 and at 24 weeks of exposure. The study showed that radiation from the 900 MHz GSM antenna is potent enough to cause distortions to DNA of H. sabdariffa even within 2-8 weeks of exposure. DNA damage was also independent of the distance from the antenna. These observations would qualify emissions from GSM mast as environmental hazard to the existence of plant biodiversities and all life forms in general. These results will trigger efforts to prevent further erosion of plant genetic resources which have been threatening food security and also the risks posed to living organisms, thereby making our environment very safe for our existence while we still continue to enjoy the benefits of the GSM technology.
Abstract: In this paper, a two-dimensional method is developed to simulate the fillet welds in a stiffened cylindrical shell, using finite element method. The stiffener material is aluminum 2519. The thermo-elasto-plastic analysis is used to analyze the thermo-mechanical behavior. Due to the high heat flux rate of the welding process, two uncouple thermal and mechanical analysis are carried out instead of performing a single couple thermo-mechanical simulation. In order to investigate the effects of the welding procedures, two different welding techniques are examined. The resulted residual stresses and distortions due to different welding procedures are obtained. Furthermore, this study employed the technique of element birth and death to simulate the weld filler variation with time in fillet welds. The obtained results are in good agreement with the published experimental and three-dimensional numerical simulation results. Therefore, the proposed 2D modeling technique can effectively give the corresponding results of 3D models. Furthermore, by inspection of the obtained residual hoop and transverse stresses and angular distortions, proper welding procedure is suggested.
Abstract: This paper presents Buck-Boost converter topology to maintain the input power factor by using the power factor stage control and regulation stage control. Suppose, if we are using the RL load the power factor will be reduced due to the presence of total harmonic distortion in the current wave. To improve the power factor the current waveform should follow the fundamental component of the voltage waveform. These can be achieved by using the high -frequency power converter. Based on the resonant circuit the converter is able to perform the function of Buck, Boost, and buck-boost converter. Here ,we have used Buck-Boost converter, because, the buck-boost converter has more advantages than the boost converter. Here the switching action of the power converter can take place by using the external zero comparator PFC stage control. The power converter consisting of the resonant circuit which is used to control the output voltage gain of the converter. The power converter is operated at a very high switching frequency in the range of 400KHz in order to overcome the switching losses of the power converter. Due to presence of high switching frequency, the power factor will improve. Therefore, the total harmonics distortion present in the current waveform has also reduced. These results has generated in the form of simulation by using MATLAB/SIMULINK software. Similar to the Buck and Boost converters, the operation of the Buck-Boost has best understood, in terms of the inductor's "reluctance" for allowing rapid change in current, which also reduces the Total Harmonic Distortion (THD) in the input current waveform, which can improve the input Power factor, based on the type of load used.
Abstract: This paper treats a design of combined control of a
single phase power factor correction (PFC). The strategy of the
proposed control is based on two parts, the first, for the outer loop
(DC output regulated voltage), and the second govern the input
current of the converter in order to achieve a sinusoidal form in phase
with the grid voltage. Two kinds of regulators are used, Fuzzy
controller for the outer loop and predictive controller for the inner
loop. The controllers are verified and discussed through simulation
under MATLAB/Simulink platform. Also an experimental
confirmation is applied. Results present a high dynamic performance
under various parameters changes.
Abstract: Parallel Compressor Model (PCM) is a simplified approach to predict compressor performance with inlet distortions. In PCM calculation, it is assumed that the sub-compressors’ outlet static pressure is uniform and therefore simplifies PCM calculation procedure. However, if the compressor’s outlet duct is not long and straight, such assumption frequently induces error ranging from 10% to 15%. This paper provides a revised calculation method of PCM that can correct the error. The revised method employs energy equation, momentum equation and continuity equation to acquire needed parameters and replace the equal static pressure assumption. Based on the revised method, PCM is applied on two compression system with different blades types. The predictions of their performance in non-uniform inlet conditions are yielded through the revised calculation method and are employed to evaluate the method’s efficiency. Validating the results by experimental data, it is found that although little deviation occurs, calculated result agrees well with experiment data whose error ranges from 0.1% to 3%. Therefore, this proves the revised calculation method of PCM possesses great advantages in predicting the performance of the distorted compressor with limited exhaust duct.
Abstract: Compressor fans in modern aircraft engines are of considerate importance, as they provide majority of thrust required by the aircraft. Their challenging environment is frequently subjected to non-uniform inflow conditions. These conditions could be either due to the flight operating requirements such as take-off and landing, wake interference from aircraft fuselage or cross-flow wind conditions. So, in highly maneuverable flights regimes of fighter aircrafts affects the overall performance of an engine. Since the flow in compressor of an aircraft application is highly sensitive because of adverse pressure gradient due to different flow orientations of the aircraft. Therefore, it is prone to unstable operations. This paper presents the study that focuses on axial compressor response to inlet flow orientations for the range of angles as 0 to 15 degrees. For this purpose, NASA Rotor-37 was taken and CFD mesh was developed. The compressor characteristics map was generated for the design conditions of pressure ratio of 2.106 with the rotor operating at rotational velocity of 17188.7 rpm using CFD simulating environment of ANSYS-CFX®. The grid study was done to see the effects of mesh upon computational solution. Then, the mesh giving the best results, (when validated with the available experimental NASA’s results); was used for further distortion analysis. The flow in the inlet nozzle was given angle orientations ranging from 0 to 15 degrees. The CFD results are analyzed and discussed with respect to stall margin and flow separations due to induced distortions.
Abstract: Carrier-based methods have been used widely for switching of multilevel inverters due to their simplicity, flexibility and reduced computational requirements compared to space vector modulation (SVM). This paper focuses on Multicarrier Sinusoidal Pulse Width Modulation (MCSPWM) strategy for the three phase Five-Level Flying Capacitor Inverter (5LFCI). The inverter is simulated for Induction Motor (IM) load and Total Harmonic Distortion (THD) for output waveforms is observed for different controlling schemes.
Abstract: This paper presents an analysis study on the impacts
of the changes of the capacitor banks, the loss of a transformer, and
the installation of distributed generation on the voltage total harmonic
distortion and harmonic resonance. The study is applied in a real
system in Oman, Sohar Industrial Port–C Substation Network.
Frequency scan method and Fourier series analysis method are used
with the help of EDSA software. Moreover, the results are compared
with limits specified by national Oman distribution code.
Abstract: In general, it is desirable to finish the weld quickly,
before a large volume of surrounding metal heats up and expands.
The welding process used, type, welding current and speed of travel,
thus, affect the degree of shrinkage and distortion of a weldment. The
use of mechanized welding equipment reduces welding time, metal
affected zone and consequently distortion. This article helps to define
what weld distortion is and then provide a practical understanding of
the causes of distortion, effects of shrinkage in butt joint welded
assemblies using TI6AL4VA and Aluminium AA2024 alloy sheet.
The beam offset position to the joint interface towards titanium and
aluminium side. The factors affecting distortion during welding is
also given. Test results reveal that welding speed is the significant
parameter to decide the extent of distortion. Also welding from Al
side reduces the distortion while Ti side increases the distortion.
Abstract: The increase in electric power demand in face of
environmental issues has intensified the participation of renewable
energy sources such as photovoltaics, in the energy matrix of various
countries. Due to their operational characteristics, they can generate
time-varying harmonic and inter-harmonic distortions. For this
reason, the application of methods of measurement based on
traditional Fourier analysis, as proposed by IEC 61000-4-7, can
provide inaccurate results. Considering the aspects mentioned herein,
came the idea of the development of this work which aims to present
the results of a comparative evaluation between a methodology
arising from the combination of the Prony method with the Kalman
filter and another method based on the IEC 61000-4-30 and IEC
61000-4-7 standards. Employed in this study were synthetic signals
and data acquired through measurements in a 50kWp photovoltaic
installation.
Abstract: Since the advances in digital imaging technologies have led to
development of high quality digital devices, there are a lot of illegal copies
of copyrighted video content on the Internet. Also, unauthorized editing is
occurred frequently. Thus, we propose an editing prevention technique for
high-quality (HQ) video that can prevent these illegally edited copies from
spreading out. The proposed technique is applied spatial and temporal gradient
methods to improve the fidelity and detection performance. Also, the scheme
duplicates the embedding signal temporally to alleviate the signal reduction
caused by geometric and signal-processing distortions. Experimental results
show that the proposed scheme achieves better performance than previously
proposed schemes and it has high fidelity. The proposed scheme can be used
in unauthorized access prevention method of visual communication or traitor
tracking applications which need fast detection process to prevent illegally
edited video content from spreading out.
Abstract: Coal fly ash, an industrial by product of coal
combustion thermal power plants is considered as a hazardous
material and its improper disposal has become an environmental
issue. On the other hand, manufacturing conventional clay bricks
involves on consumption of large amount of clay and leads
substantial depletion of topsoil. This paper unveils the possibility of
using fly ash as a partial replacement of clay for brick manufacturing
considering the local technology practiced in Bangladesh. The effect
of fly ash with different replacing ratio (0%, 20%, 30%, 40%, and
50% by volume) of clay on properties of bricks was studied. Bricks
were made in the field parallel to ordinary bricks marked with
specific number for different percentage to identify them at time of
testing. No physical distortion is observed in fly ash brick after
burning in the kiln. Results from laboratory test show that
compressive strength of brick is decreased with the increase of fly
ash and maximum compressive strength is found to be 19.6 MPa at
20% of fly ash. In addition, water absorption of fly ash brick is
increased with the increase of fly ash. The abrasion value and
Specific gravity of coarse aggregate prepared from brick with fly ash
also studied and the results of this study suggests that 20% fly ash
can be considered as the optimum fly ash content for producing good
quality bricks utilizing present practiced technology.
Abstract: Magnetic Resonance Imaging (MRI) is one of the
most important medical imaging modality. Subjective assessment of
the image quality is regarded as the gold standard to evaluate MR
images. In this study, a database of 210 MR images which contains
ten reference images and 200 distorted images is presented. The
reference images were distorted with four types of distortions: Rician
Noise, Gaussian White Noise, Gaussian Blur and DCT compression.
The 210 images were assessed by ten subjects. The subjective scores
were presented in Difference Mean Opinion Score (DMOS). The
DMOS values were compared with four FR-IQA metrics. We have
used Pearson Linear Coefficient (PLCC) and Spearman Rank Order
Correlation Coefficient (SROCC) to validate the DMOS values. The
high correlation values of PLCC and SROCC shows that the DMOS
values are close to the objective FR-IQA metrics.
Abstract: Fresh water is one of the resources which is getting
depleted day by day. A wise method to address this issue is by the
application of renewable energy-sun irradiation and by means of
decentralized, cheap, energetically self-sufficient, robust and simple
to operate plants, distillates can be obtained from sea, river or even
sewage. Solar desalination is a technique used to desalinate water
using solar energy. The present work deals with the comprehensive
design and simulation of solar tracking system using LabVIEW,
temperature and mass flow rate control of the solar desalination plant
using LabVIEW and also analysis of single phase inverter circuit
with LC filters for solar pumping system in MATLAB. The main
objective of this work is to improve the performance of solar
desalination system using automatic tracking system, output control
using temperature and mass flow rate control system and also to
reduce the harmonic distortion in the solar pumping system by means
of LC filters. The simulation of single phase inverter was carried out
using MATLAB and the output waveforms were analyzed.
Simulations were performed for optimum output temperature control,
which in turn controls the mass flow rate of water in the thermal
collectors. Solar tracking system was accomplished using LABVIEW
and was tested successfully. The thermal collectors are tracked in
accordance with the sun’s irradiance levels, thereby increasing the
efficiency of the thermal collectors.
Abstract: Polylactic acid (PLA) is the most commercially
available bio-based and biodegradable plastic at present. PLA has
been used in plastic related industries including single-used
containers, disposable and environmentally friendly packaging owing
to its renewability, compostability, biodegradability, and safety.
Although PLA demonstrates reasonably good optical, physical,
mechanical and barrier properties comparable to the existing
petroleum-based plastics, its brittleness and mold shrinkage as well as
its price are the points to be concerned for the production of rigid and
semi-rigid packaging. Blending PLA with other bio-based polymers
including thermoplastic starch (TPS) is an alternative not only to
achieve a complete bio-based plastic, but also to reduce the
brittleness, shrinkage during molding and production cost of the
PLA-based products. TPS is a material produced mainly from starch
which is cheap, renewable, biodegradable, compostable, and nontoxic.
It is commonly prepared by a plasticization of starch under
applying heat and shear force. Although glycerol has been reported as
one of the most plasticizers used for preparing TPS, its migration
caused the surface stickiness of the TPS products. In some cases,
mixed plasticizers or natural fibers have been applied to impede the
retrogradation of starch or reduce the migration of glycerol. The
introduction of fibers into TPS-based materials could reinforce the
polymer matrix as well. Therefore, the objective of the present
research is to study the effect of starch type (i.e. native starch and
phosphate starch), plasticizer type (i.e. glycerol and xylitol with a
weight ratio of glycerol to xylitol of 100:0, 75:25, 50:50, 25:75 and
0:100) and fiber content (i.e. in the range of 1-25 %wt) on properties
of PLA/TPS blend and composite. PLA/TPS blends and composites
were prepared using a twin-screw extruder and then converted into
dumbbell-shaped specimens using an injection molding machine. The
PLA/TPS blends prepared by using phosphate starch showed higher
tensile strength and stiffness than the blends prepared by using native
one. In contrast, the blends from native starch exhibited higher
extensibility and heat distortion temperature (HDT) than those from
the modified starch. Increasing xylitol content resulted in enhanced
tensile strength, stiffness and water resistance, but decreased
extensibility and HDT of the PLA/TPS blend. Tensile properties and
hydrophobicity of the blend could be improved by incorporating
silane treated-jute fibers.
Abstract: This paper integrates Octagon and Square Search
pattern (OCTSS) motion estimation algorithm into H.264/AVC
(Advanced Video Coding) video codec in Adaptive Group of Pictures
(AGOP) mode. AGOP structure is computed based on scene change
in the video sequence. Octagon and square search pattern block-based
motion estimation method is implemented in inter-prediction process
of H.264/AVC. Both these methods reduce bit rate and computational
complexity while maintaining the quality of the video sequence
respectively. Experiments are conducted for different types of video
sequence. The results substantially proved that the bit rate,
computation time and PSNR gain achieved by the proposed method
is better than the existing H.264/AVC with fixed GOP and AGOP.
With a marginal gain in quality of 0.28dB and average gain in bitrate
of 132.87kbps, the proposed method reduces the average computation
time by 27.31 minutes when compared to the existing state-of-art
H.264/AVC video codec.