Abstract: This paper presents the variation of the dynamic
characteristics of a spindle with the change of bearing preload. The
correlations between the variation of bearing preload and fundamental
modal parameters were first examined by conducting vibration tests on
physical spindle units. Experimental measurements show that the
dynamic compliance and damping ratio associated with the
dominating modes were affected to vary with variation of the bearing
preload. When the bearing preload was slightly deviated from a
standard value, the modal frequency and damping ability also vary to
different extent, which further enable the spindle to perform with
different compliance. For the spindle used in this study, a standard
preload value set on bearings would enable the spindle to behave a
higher stiffness as compared with others with a preload variation. This
characteristic can be served as a reference to examine the variation of
bearing preload of spindle in assemblage or operation.
Abstract: In this paper the vibration of a synchronous belt drive
during start-up is analyzed and discussed. Besides considering the
belt elasticity, the model here proposed also takes into consideration
the electromagnetic response of the DC motor. The solution of the
motion equations is obtained by means of the modal analysis in
state space, which allows to obtain the decoupling of all equations,
without introducing the hypothesis of proportional damping. The
mathematical model of the transmission and the solution algorithms
have been implemented within a computing software that allows the
user to simulate the dynamics of the system and to evaluate the effects
due to the elasticity of the belt branches and to the electromagnetic
behavior of the DC motor. In order to show the details of the
calculation procedure, the paper presents a case study developed with
the aid of the above-mentioned software.
Abstract: Based on three dimensional potential flow theory and hinged rigid body motion equations, structure RAOs of Pelamis wave energy converter is analyzed. Analysis of numerical simulation is carried out on Pelamis in the irregular wave conditions, and the motion response of structures and total generated power is obtained. The paper analyzes influencing factors on the average power including diameter of floating body, section form of floating body, draft, hinged stiffness and damping. The optimum parameters are achieved in Zhejiang Province. Compared with the results of the pelamis experiment made by Glasgow University, the method applied in this paper is feasible.
Abstract: The paper analyzes the response of buildings and industrially structures on seismic waves (low frequency mechanical vibration) generated by blasting operations. The principles of seismic analysis can be applied for different kinds of excitation such as: earthquakes, wind, explosions, random excitation from local transportation, periodic excitation from large rotating and/or machines with reciprocating motion, metal forming processes such as forging, shearing and stamping, chemical reactions, construction and earth moving work, and other strong deterministic and random energy sources caused by human activities. The article deals with the response of seismic, low frequency, mechanical vibrations generated by nearby blasting operations on a residential home. The goal was to determine the fundamental natural frequencies of the measured structure; therefore it is important to determine the resonant frequencies to design a suitable modal damping. The article also analyzes the package of seismic waves generated by blasting (Primary waves – P-waves and Secondary waves S-waves) and investigated the transfer regions. For the detection of seismic waves resulting from an explosion, the Fast Fourier Transform (FFT) and modal analysis, in the frequency domain, is used and the signal was acquired and analyzed also in the time domain. In the conclusions the measured results of seismic waves caused by blasting in a nearby quarry and its effect on a nearby structure (house) is analyzed. The response on the house, including the fundamental natural frequency and possible fatigue damage is also assessed.
Abstract: This paper presents the mathematical description of the high-speed rotating system taking into account the influence of internal and external damping. The mathematical model is obtained by using the finite element method. The analyzed system is an automotive turbocharger understood as a rotor-bearing system. The circular cross-section shaft is equipped with one compressor wheel, one turbine wheel and is supported by two floating ring bearings. Based on the model, the dynamical analysis of a turbocharger is performed and stability conditions are evaluated.
Abstract: The motion planning procedure described in this paper has been developed in order to eliminate or reduce the residual vibrations of electromechanical positioning systems, without augmenting the motion time (usually imposed by production requirements), nor introducing overtime for vibration damping. The proposed technique is based on a suitable choice of the motion law assigned to the servomotor that drives the mechanism. The reference profile is defined by a Bezier curve, whose shape can be easily changed by modifying some numerical parameters. By means of an optimization technique these parameters can be modified without altering the continuity conditions imposed on the displacement and on its time derivatives at the initial and final time instants.
Abstract: In this study, it is investigated the stability boundary of
Functionally Graded (FG) panel under the heats and supersonic
airflows. Material properties are assumed to be temperature
dependent, and a simple power law distribution is taken. First-order
shear deformation theory (FSDT) of plate is applied to model the
panel, and the von-Karman strain- displacement relations are
adopted to consider the geometric nonlinearity due to large
deformation. Further, the first-order piston theory is used to model the
supersonic aerodynamic load acting on a panel and Rayleigh damping
coefficient is used to present the structural damping. In order to find a
critical value of the speed, linear flutter analysis of FG panels is
performed. Numerical results are compared with the previous works,
and present results for the temperature dependent material are
discussed in detail for stability boundary of the panel with various
volume fractions, and aerodynamic pressures.
Abstract: Both the minimum energy consumption and
smoothness, which is quantified as a function of jerk, are generally
needed in many dynamic systems such as the automobile and the
pick-and-place robot manipulator that handles fragile equipments.
Nevertheless, many researchers come up with either solely
concerning on the minimum energy consumption or minimum jerk
trajectory. This research paper considers the indirect minimum Jerk
method for higher order differential equation in dynamics
optimization proposes a simple yet very interesting indirect jerks
approaches in designing the time-dependent system yielding an
alternative optimal solution. Extremal solutions for the cost functions
of indirect jerks are found using the dynamic optimization methods
together with the numerical approximation. This case considers the
linear equation of a simple system, for instance, mass, spring and
damping. The simple system uses two mass connected together by
springs. The boundary initial is defined the fix end time and end
point. The higher differential order is solved by Galerkin-s methods
weight residual. As the result, the 6th higher differential order shows
the faster solving time.
Abstract: In the various working field, vibration may cause injurious to human body. Especially, in case of the vibration which is constantly and repeatedly transferred to the human. That gives serious physical problem, so called, Reynaud phenomenon. In this paper, we propose a vibration transmissibility reduction module with flexure mechanism for personal tools. At first, we select a target personal tool, grass cutter, and measure the level of vibration transmissibility on the hand. And then, we develop the concept design of the module that has stiffness for reduction the vibration transmissibility more than 20%, where the vibration transmissibility is measured with an accelerometer. In addition, the vibration reduction can be enhanced when the interior gap between inner and outer body is filled with silicone gel. This will be verified by the further experiment.
Abstract: Sound pathways in the enclosures of small earphones
are very narrow. In such narrow pathways, the speed of sound
propagation and the phase of sound waves change because of the air
viscosity. We have developed a new finite element method that
includes the effects of damping due to air viscosity for modeling the
sound pathway. This method is developed as an extension of the
existing finite element method for porous sound-absorbing materials.
The numerical calculation results using the proposed finite element
method are validated against the existing calculation methods.
Abstract: This paper focuses on a technique for identifying the geological boundary of the ground strata in front of a tunnel excavation site using the first order adjoint method based on the optimal control theory. The geological boundary is defined as the boundary which is different layers of elastic modulus. At tunnel excavations, it is important to presume the ground situation ahead of the cutting face beforehand. Excavating into weak strata or fault fracture zones may cause extension of the construction work and human suffering. A theory for determining the geological boundary of the ground in a numerical manner is investigated, employing excavating blasts and its vibration waves as the observation references. According to the optimal control theory, the performance function described by the square sum of the residuals between computed and observed velocities is minimized. The boundary layer is determined by minimizing the performance function. The elastic analysis governed by the Navier equation is carried out, assuming the ground as an elastic body with linear viscous damping. To identify the boundary, the gradient of the performance function with respect to the geological boundary can be calculated using the adjoint equation. The weighed gradient method is effectively applied to the minimization algorithm. To solve the governing and adjoint equations, the Galerkin finite element method and the average acceleration method are employed for the spatial and temporal discretizations, respectively. Based on the method presented in this paper, the different boundary of three strata can be identified. For the numerical studies, the Suemune tunnel excavation site is employed. At first, the blasting force is identified in order to perform the accuracy improvement of analysis. We identify the geological boundary after the estimation of blasting force. With this identification procedure, the numerical analysis results which almost correspond with the observation data were provided.
Abstract: Wind power is among the most actively developing distributed generation (DG) technology. Majority of the wind power based DG technologies employ wind turbine induction generators (WTIG) instead of synchronous generators, for the technical advantages like: reduced size, increased robustness, lower cost, and increased electromechanical damping. However, dynamic changes of wind speed make the amount of active/reactive power injected/drawn to a WTIG embedded distribution network highly variable. This paper analyzes the effect of wind speed changes on the active and reactive power penetration to the wind energy embedded distribution network. Four types of wind speed changes namely; constant, linear change, gust change and random change of wind speed are considered in the analysis. The study is carried out by three-phase, non-linear, dynamic simulation of distribution system component models. Results obtained from the investigation are presented and discussed.
Abstract: Series compensators have been used for many years,
to increase the stability and load ability of transmission line. They
compensate retarded or advanced volt drop of transmission lines
by placing advanced or retarded voltage in series with them to
compensate the effective reactance, which cause to increase load
ability of transmission lines. In this paper, two method of fuzzy
controller, based on power reference tracking and impedance
reference tracking have been developed on TCSC controller in
order to increase load ability and improving power oscillation
damping of system. In these methods, fire angle of thyristors are
determined directly through the special Rule-bases with the error
and change of error as the inputs. The simulation results of two
area four- machines power system show the good performance of
power oscillation damping in system. Comparison of this method
with classical PI controller shows the increasing speed of system
response in power oscillation damping.
Abstract: This paper describes dynamic analysis using proposed
fast finite element method for a shock absorbing structure including a
sponge. The structure is supported by nonlinear concentrated springs.
The restoring force of the spring has cubic nonlinearity and linear
hysteresis damping. To calculate damping properties for the structures
including elastic body and porous body, displacement vectors as
common unknown variable are solved under coupled condition. Under
small amplitude, we apply asymptotic method to complex eigenvalue
problem of this system to obtain modal parameters. And then
expressions of modal loss factor are derived approximately. This
approach was proposed by one of the authors previously. We call this
method as Modal Strain and Kinetic Energy Method (MSKE method).
Further, using the modal loss factors, the discretized equations in
physical coordinate are transformed into the nonlinear ordinary
coupled equations using normal coordinate corresponding to linear
natural modes. This transformation yields computation efficiency. As
a numerical example of a shock absorbing structures, we adopt double
skins with a sponge. The double skins are supported by nonlinear
concentrated springs. We clarify influences of amplitude of the input
force on nonlinear and chaotic responses.
Abstract: This paper describes vibration analysis using the finite
element method for a small earphone, especially for the diaphragm
shape with a low-rigidity. The viscoelastic diaphragm is supported by
multiple nonlinear concentrated springs with linear hysteresis
damping. The restoring forces of the nonlinear springs have cubic
nonlinearity. The finite elements for the nonlinear springs with
hysteresis are expressed and are connected to the diaphragm that is
modeled by linear solid finite elements in consideration of a complex
modulus of elasticity. Further, the discretized equations in physical
coordinates are transformed into the nonlinear ordinary coupled
equations using normal coordinates corresponding to the linear natural
modes. We computed the nonlinear stationary and non-stationary
responses due to the internal resonance between modes with large
amplitude in the nonlinear springs and elastic modes in the diaphragm.
The non-stationary motions are confirmed as the chaos due to the
maximum Lyapunov exponents with a positive number. From the time
histories of the deformation distribution in the chaotic vibration, we
identified nonlinear modal couplings.
Abstract: This paper investigates and compares performance of
various conventional and fuzzy logic based controllers at generator
locations for oscillation damping. Performance of combination of
conventional and fuzzy logic based controllers also studied by
comparing overshoot on the active power deviation response for a
small disturbance and damping ratio of the critical mode. Fuzzy logic
based controllers can not be modeled in the state space form to get
the eigenvalues and corresponding damping ratios of various modes
of generators and controllers. Hence, a new method based on tracing
envelop of time domain waveform is also presented and used in the
paper for comparing performance of controllers. The paper also
shows that if the fuzzy based controllers designed separately
combining them could not lead to a better performance.