Abstract: A highly optimized implementation of binary mixture
diffusion with no initial bulk velocity on graphics processors is
presented. The lattice Boltzmann model is employed for simulating
the binary diffusion of oxygen and nitrogen into each other with
different initial concentration distributions. Simulations have been
performed using the latest proposed lattice Boltzmann model that
satisfies both the indifferentiability principle and the H-theorem for
multi-component gas mixtures. Contemporary numerical
optimization techniques such as memory alignment and increasing
the multiprocessor occupancy are exploited along with some novel
optimization strategies to enhance the computational performance on
graphics processors using the C for CUDA programming language.
Speedup of more than two orders of magnitude over single-core
processors is achieved on a variety of Graphical Processing Unit
(GPU) devices ranging from conventional graphics cards to
advanced, high-end GPUs, while the numerical results are in
excellent agreement with the available analytical and numerical data
in the literature.
Abstract: In this paper, the effect of bolt clamping force on the fatigue behavior of bolted single lap joints of aluminum alloy 2024- T3 have been studied using numerical finite element method. To do so, a three dimensional model according to the bolted single lap joint has been created and numerical analysis has been carried out using finite element based package. Then the stress distribution and also the slip amplitudes have been calculated in the critical regions and the outcome have been compared with the available experimental fatigue tests results. The numerical results show that in low applied clamping force, the fatigue failure of the specimens occur around the stress concentration location (the bolted hole edge) due to the tensile stresses and thus fatigue crack propagation, but with increase of the clamping force, the fatigue life increases and the cracks nucleate and propagate far from the hole edge because of fretting fatigue. In other words, with the further increase of clamping force value of the joint, the fatigue life reduces due to occurrence of the fretting fatigue in the critical location where the slip amplitude is within its critical occurs earlier.
Abstract: Numerical investigation of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann methods at different Reynolds numbers. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations, streamlines and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The Reynolds numbers affected the physical quantities.
Abstract: Most buildings have been using anchor bolts
commonly for installing outdoor advertising structures. Anchor bolts
of common carbon steel are widely used and often installed
indiscriminately by inadequate installation standards. In the area
where strong winds frequently blow, falling accidents of outdoor
advertising structures can occur and cause a serious disaster, which is
very dangerous and to be prevented. In this regard, the development of
high-performance anchor bolts is urgently required. In the present
study, 25Cr-8Ni-1.5Si-1Mn-0.4C alloy was produced by traditional
vacuum induction melting (VIM) for the application of anchor bolt.
The alloy composition is revealed as a duplex microstructure from
thermodynamic phase analysis by FactSage® and confirmed by
metallographic experiment. Addition of Nitrogen to the alloy was
found to reduce the ferritic phase domain and significantly increase the
hardness and the tensile strength. Microstructure observation revealed
mixed structure of austenite and ferrite with fine carbide distributed
along the grain and phase boundaries.
Abstract: To determine the length of engagement threads of a bolt installed in a tapped part in order to avoid the threads stripping remains a very current problem in the design of the thread assemblies. It does not exist a calculation method formalized for the cases where the bolt is screwed directly in a ductile material. In this article, we study the behavior of the threads stripping of a loaded assembly by using a modelling by finite elements and a rupture criterion by damage. This modelling enables us to study the different parameters likely to influence the behavior of this bolted connection. We study in particular, the influence of couple of materials constituting the connection, of the bolt-s diameter and the geometrical characteristics of the tapped part, like the external diameter and the length of engagement threads. We established an experiments design to know the most significant parameters. That enables us to propose a simple expression making possible to calculate the resistance of the threads whatever the metallic materials of the bolt and the tapped part. We carried out stripping tests in order to validate our model. The estimated results are very close to those obtained by the tests.
Abstract: In this paper we present discretization and decomposition methods for a multi-component transport model of a chemical vapor deposition (CVD) process. CVD processes are used to manufacture deposition layers or bulk materials. In our transport model we simulate the deposition of thin layers. The microscopic model is based on the heavy particles, which are derived by approximately solving a linearized multicomponent Boltzmann equation. For the drift-process of the particles we propose diffusionreaction equations as well as for the effects of heat conduction. We concentrate on solving the diffusion-reaction equation with analytical and numerical methods. For the chemical processes, modelled with reaction equations, we propose decomposition methods and decouple the multi-component models to simpler systems of differential equations. In the numerical experiments we present the computational results of our proposed models.
Abstract: In the present study, the lattice Boltzmann Method (LBM) is applied for simulating of Natural Convection in an inclined open ended cavity. The cavity horizontal walls are insulated while the west wall is maintained at a uniform temperature higher than the ambient. Prandtl number is fixed to 0.71 (air) while Rayligh numbers, aspect ratio of the cavity are changed in the range of 103 to 104 and of 1-4, respectively. The numerical code is validated for the previously results for open ended cavities, and then the results of an inclined open ended cavity for various angles of rotating open ended cavity are presented. Result shows by increasing of aspect ratio, the average Nusselt number on hot wall decreases for all rotation angles. When gravity acceleration direction is opposite of standard gravity direction the convection heat transfer has a manner same as conduction.
Abstract: The aim of the study was to evaluate the effect of
texturizers on the rheological properties of the apple mass and
desserts made from various raw materials. The apple varieties -
‘Antonovka’, ‘Baltais Dzidrais’, and ‘Zarja Alatau’ harvested in
Latvia, were used for the experiment. The apples were processed in a
blender unpeeled for obtaining a homogenous mass. The apple mass
was analyzed fresh and after storage at –18ºC. Both fresh and thawed
apple mass samples with added gelatin, xantan gum, and sodium
carboxymethylcellulose were whisked obtaining dessert. Pectin, pH
and soluble dry matter of the product were determined. Apparent
viscosity was measured using a rotational viscometer DV–III Ultra.
Pectin content in frozen apple mass decreased significantly (p
Abstract: In this paper, the details of an experimental method to measure the clamping force value at bolted connections due to application of wrenching torque to tighten the nut have been presented. A simplified bolted joint including a holed plate with a single bolt was considered to carry out the experiments. This method was designed based on Hooke-s law by measuring compressive axial strain of a steel bush placed between the nut and the plate. In the experimental procedure, the values of clamping force were calculated for seven different levels of applied torque, and this process was repeated three times for each level of the torque. Moreover, the effect of lubrication of threads on the clamping value was studied using the same method. In both conditions (dry and lubricated threads), relation between the torque and the clamping force have been displayed in graphs.
Abstract: Although water only takes a little percentage in the total mass of soil, it indeed plays an important role to the strength of structure. Moisture transfer can be carried out by many different mechanisms which may involve heat and mass transfer, thermodynamic phase change, and the interplay of various forces such as viscous, buoyancy, and capillary forces. The continuum models are not well suited for describing those phenomena in which the connectivity of the pore space or the fracture network, or that of a fluid phase, plays a major role. However, Lattice Boltzmann methods (LBMs) are especially well suited to simulate flows around complex geometries. Lattice Boltzmann methods were initially invented for solving fluid flows. Recently, fluid with multicomponent and phase change is also included in the equations. By comparing the numerical result with experimental result, the Lattice Boltzmann methods with phase change will be optimized.
Abstract: The hydrodynamic and thermal lattice Boltzmann
methods are applied to investigate the turbulent convective heat
transfer in the wavy channel flows. In this study, the turbulent
phenomena are modeling by large-eddy simulations with the
Smagorinsky model. As a benchmark, the laminar and turbulent
backward-facing step flows are simulated first. The results give good
agreement with other numerical and experimental data. For wavy
channel flows, the distribution of Nusselt number and the skin-friction
coefficients are calculated to evaluate the heat transfer effect and the
drag force. It indicates that the vortices at the trough would affect the
magnitude of drag and weaken the heat convection effects on the wavy
surface. In turbulent cases, if the amplitude of the wavy boundary is
large enough, the secondary vortices would be generated at troughs
and contribute to the heat convection. Finally, the effects of different
Re on the turbulent transport phenomena are discussed.
Abstract: We report the results of an lattice Boltzmann
simulation of magnetohydrodynamic damping of sidewall convection
in a rectangular enclosure filled with a porous medium. In particular
we investigate the suppression of convection when a steady magnetic
field is applied in the vertical direction. The left and right vertical
walls of the cavity are kept at constant but different temperatures
while both the top and bottom horizontal walls are insulated. The
effects of the controlling parameters involved in the heat transfer and
hydrodynamic characteristics are studied in detail. The heat and mass
transfer mechanisms and the flow characteristics inside the enclosure
depended strongly on the strength of the magnetic field and Darcy
number. The average Nusselt number decreases with rising values of
the Hartmann number while this increases with increasing values of
the Darcy number.
Abstract: We report the results of an lattice Boltzmann
simulation of magnetohydrodynamic damping of sidewall convection
in a rectangular enclosure filled with a porous medium. In particular
we investigate the suppression of convection when a steady magnetic
field is applied in the vertical direction. The left and right vertical
walls of the cavity are kept at constant but different temperatures
while both the top and bottom horizontal walls are insulated. The
effects of the controlling parameters involved in the heat transfer and
hydrodynamic characteristics are studied in detail. The heat and mass
transfer mechanisms and the flow characteristics inside the enclosure
depended strongly on the strength of the magnetic field and Darcy
number. The average Nusselt number decreases with rising values of
the Hartmann number while this increases with increasing values of
the Darcy number.
Abstract: The dynamics of Min proteins plays a center role in
accurate cell division. Although the nucleoids may presumably play
an important role in prokaryotic cell division, there is a lack of
models to account for its participation. In this work, we apply the
lattice Boltzmann method to investigate protein oscillation based on a
mesoscopic model that takes into account the nucleoid-s role. We
found that our numerical results are in reasonably good agreement
with the previous experimental results On comparing with the other
computational models without the presence of nucleoids, the
highlight of our finding is that the local densities of MinD and MinE
on the cytoplasmic membrane increases, especially along the cell
width, when the size of the obstacle increases, leading to a more
distinct cap-like structure at the poles. This feature indicated the
realistic pattern and reflected the combination of Min protein
dynamics and nucleoid-s role.
Abstract: In this paper the fatigue crack initiation location of double shear lap joints, treated by interference fit and bolt clamping, have been investigated both experimentally and numerically. To do so, using the fracture section of available fatigue tested specimens of interference fitted and torque tightened Aluminum 2024-T3 plates, the crack initiation location was determined. The stress distribution attained from the finite element analysis was used to help explain the results observed in the experimental tests. The results showed that the fatigue crack initiation location changes from top and mid plane at the hole edge to somewhere far from the hole edge (stress concentration region) in different combination of clamping force, interference fit size and applied cyclic load ranges. It is worth mentioning that the fatigue crack initiation location affects the fatigue life of the specimens too.
Abstract: Adhesively bonded joints are preferred over the
conventional methods of joining such as riveting, welding, bolting
and soldering. Some of the main advantages of adhesive joints
compared to conventional joints are the ability to join dissimilar
materials and damage-sensitive materials, better stress distribution,
weight reduction, fabrication of complicated shapes, excellent
thermal and insulation properties, vibration response and enhanced
damping control, smoother aerodynamic surfaces and an
improvement in corrosion and fatigue resistance. This paper presents
the behavior of adhesively bonded joints subjected to combined
thermal loadings, using the numerical methods. The joint
configuration considers aluminum as central adherend with six
different outer adherends including aluminum, steel, titanium, boronepoxy,
unidirectional graphite-epoxy and cross-ply graphite-epoxy
and epoxy-based adhesives. Free expansion of the joint in x
direction was permitted and stresses in adhesive layer and interfaces
calculated for different adherends.
Abstract: In this paper, we propose an architecture for easily
constructing a robot controller. The architecture is a multi-agent
system which has eight agents: the Man-machine interface, Task
planner, Task teaching editor, Motion planner, Arm controller,
Vehicle controller, Vision system and CG display. The controller has
three databases: the Task knowledge database, the Robot database and
the Environment database. Based on this controller architecture, we
are constructing an experimental power distribution line maintenance
robot system and are doing the experiment for the maintenance tasks,
for example, “Bolt insertion task".
Abstract: In this paper, experimental testing and numerical analysis were used to investigate the effect of tube thickness on the face bending for concrete filled hollow sections connected to other structural members using Extended Hollobolts. Six samples were tested experimentally by applying pull-out load on the bolts. These samples were designed to fail by column face bending. The main variable in all tests is the column face thickness. Finite element analyses were also performed using ABAQUS 6.11 to extend the experimental results and to quantify the effect of column face thickness. Results show that, the column face thickness has a clear impact on the connection strength and stiffness. However, the amount of improvement in the connection stiffness by changing the column face thickness from 5mm to 6.3mm seems to be higher than that when increasing it from 6.3mm to 8mm. The displacement at which the bolts start pulling-out from their holes increased with the use of thinner column face due to the high flexibility of the section. At the ultimate strength, the yielding of the column face propagated to the column corner and there was no yielding in its walls. After the ultimate resistance is reached, the propagation of the yielding was mainly in the column face with a miner yielding in the walls.
Abstract: In this paper, Lattice Boltzmann Method (LBM) is used to study laminar flow with mixed convection heat transfer inside a two-dimensional inclined lid-driven rectangular cavity with aspect ratio AR = 3. Bottom wall of the cavity is maintained at lower temperature than the top lid, and its vertical walls are assumed insulated. Top lid motion results in fluid motion inside the cavity. Inclination of the cavity causes horizontal and vertical components of velocity to be affected by buoyancy force. To include this effect, calculation procedure of macroscopic properties by LBM is changed and collision term of Boltzmann equation is modified. A computer program is developed to simulate this problem using BGK model of lattice Boltzmann method. The effects of the variations of Richardson number and inclination angle on the thermal and flow behavior of the fluid inside the cavity are investigated. The results are presented as velocity and temperature profiles, stream function contours and isotherms. It is concluded that LBM has good potential to simulate mixed convection heat transfer problems.
Abstract: Simultaneous transient conduction and radiation heat
transfer with heat generation is investigated. Analysis is carried out
for both steady and unsteady situations. two-dimensional gray
cylindrical enclosure with an absorbing, emitting, and isotropically
scattering medium is considered. Enclosure boundaries are assumed
at specified temperatures. The heat generation rate is considered
uniform and constant throughout the medium. The lattice Boltzmann
method (LBM) was used to solve the energy equation of a transient
conduction-radiation heat transfer problem. The control volume finite
element method (CVFEM) was used to compute the radiative
information. To study the compatibility of the LBM for the energy
equation and the CVFEM for the radiative transfer equation, transient
conduction and radiation heat transfer problems in 2-D cylindrical
geometries were considered. In order to establish the suitability of the
LBM, the energy equation of the present problem was also solved
using the the finite difference method (FDM) of the computational
fluid dynamics. The CVFEM used in the radiative heat transfer was
employed to compute the radiative information required for the
solution of the energy equation using the LBM or the FDM (of the
CFD). To study the compatibility and suitability of the LBM for the
solution of energy equation and the CVFEM for the radiative
information, results were analyzed for the effects of various
parameters such as the boundary emissivity. The results of the LBMCVFEM
combination were found to be in excellent agreement with
the FDM-CVFEM combination. The number of iterations and the
steady state temperature in both of the combinations were found
comparable. Results are found for situations with and without heat
generation. Heat generation is found to have significant bearing on
temperature distribution.