Abstract: This research proposes an algorithm for the simulation
of time-periodic unsteady problems via the solution unsteady Euler
and Navier-Stokes equations. This algorithm which is called Time
Spectral method uses a Fourier representation in time and hence
solve for the periodic state directly without resolving transients
(which consume most of the resources in a time-accurate scheme).
Mathematical tools used here are discrete Fourier transformations. It
has shown tremendous potential for reducing the computational cost
compared to conventional time-accurate methods, by enforcing
periodicity and using Fourier representation in time, leading to
spectral accuracy. The accuracy and efficiency of this technique is
verified by Euler and Navier-Stokes calculations for pitching airfoils.
Because of flow turbulence nature, Baldwin-Lomax turbulence
model has been used at viscous flow analysis. The results presented
by the Time Spectral method are compared with experimental data. It
has shown tremendous potential for reducing the computational cost
compared to the conventional time-accurate methods, by enforcing
periodicity and using Fourier representation in time, leading to
spectral accuracy, because results verify the small number of time
intervals per pitching cycle required to capture the flow physics.
Abstract: In this paper we proposed multistage adaptive
ARQ/HARQ/HARQ scheme. This method combines pure ARQ
(Automatic Repeat reQuest) mode in low channel bit error rate and
hybrid ARQ method using two different Reed-Solomon codes in
middle and high error rate conditions. It follows, that our scheme has
three stages. The main goal is to increase number of states in adaptive
HARQ methods and be able to achieve maximum throughput for
every channel bit error rate. We will prove the proposal by
calculation and then with simulations in land mobile satellite channel
environment. Optimization of scheme system parameters is described
in order to maximize the throughput in the whole defined Signal-to-
Noise Ratio (SNR) range in selected channel environment.
Abstract: The characterisation of agro-wastes fibres for composite applications from Nigeria using X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM) has been done. Fibres extracted from groundnut shell, coconut husk, rice husk, palm fruit bunch and palm fruit stalk are processed using two novel cellulose fibre production methods developed by the authors. Cellulose apparent crystallinity calculated using the deconvolution of the diffractometer trace shows that the amorphous portion of cellulose was permeable to hydrolysis yielding high crystallinity after treatment. All diffratograms show typical cellulose structure with well-defined 110, 200 and 040 peaks. Palm fruit fibres had the highest 200 crystalline cellulose peaks compared to others and it is an indication of rich cellulose content. Surface examination of the resulting fibres using SEM indicates the presence of regular cellulose network structure with some agglomerated laminated layer of thin leaves of cellulose microfibrils. The surfaces were relatively smooth indicating the removal of hemicellulose, lignin and pectin.
Abstract: Physiological control of a left ventricle assist device (LVAD) is generally a complicated task due to diverse operating environments and patient variability. In this work, a tracking control algorithm based on sliding mode and feed forward control for a class of discrete-time single input single output (SISO) nonlinear uncertain systems is presented. The controller was developed to track the reference trajectory to a set operating point without inducing suction in the ventricle. The controller regulates the estimated mean pulsatile flow Qp and mean pulsatility index of pump rotational speed PIω that was generated from a model of the assist device. We recall the principle of the sliding mode control theory then we combine the feed-forward control design with the sliding mode control technique to follow the reference trajectory. The uncertainty is replaced by its upper and lower boundary. The controller was tested in a computer simulation covering two scenarios (preload and ventricular contractility). The simulation results prove the effectiveness and the robustness of the proposed controller
Abstract: The dramatic effect of information technology on
society is undeniable. In education, it is evident in the use of terms
like active learning, blended learning, electronic learning and mobile
learning (ubiquitous learning). This study explores the perceptions of
54 learners in a higher education institution regarding the use of
mobile devices in a third year module. Using semi-structured
interviews, it was found that mobile devices had a positive impact on
learner motivation, engagement and enjoyment. It also improved the
consistency of learning material, and the convenience and flexibility
(anywhere, anytime) of learning. User-interfacelimitation, bandwidth
and cognitive overload, however, were of concern. The use of cloud
based resources like Youtube and Google Docs, through mobile
devices, positively influenced learner perceptions, making them
prosumers (both consumers and producers) of education content.
Abstract: Based on the Lagrangian for the Gross –Pitaevskii
equation as derived by H. Sakaguchi and B.A Malomed [5] we have
derived a double well model for the nonlinear optical lattice. This
model explains the various features of nonlinear optical lattices.
Further, from this model we obtain and simulate the probability for
tunneling from one well to another which agrees with experimental
results [4].
Abstract: The study was carried out to gather and identify
medicinal plants their curative effects and the part of them which is
used from the reservation area of Miankaleh. The region under study
has an area of 68800 hectares situated 12 kilometers north of the city
of Behshahr and northwest of the city of Gorgan. Results obtained
showed that out of a total of 43 families, 125 genera, and 155 species
found in the region, 33 families, 52 genera and 61 species (39% of all
the species) belonged to medicinal plants, among which the class
Asteraceae with 6 species and the class Chenopodiaceae with 5
species had the most medicinal species. The most used parts of the
plants were the leaves with 31%, the whole plants with 19%, and the
roots with 15%.
Abstract: As communications systems and technology become more advanced and complex, it will be increasingly important to focus on users- individual needs. Personalization and effective user profile management will be necessary to ensure the uptake and success of new services and devices and it is therefore important to focus on the users- requirements in this area and define solutions that meet these requirements. The work on personalization and user profiles emerged from earlier ETSI work on a Universal Communications Identifier (UCI) which is a unique identifier of the user rather than a range of identifiers of the many of communication devices or services (e.g. numbers of fixed phone at home/work, mobile phones, fax and email addresses). This paper describes work on personalization including standardized information and preferences and an architectural framework providing a description of how personalization can be integrated in Next Generation Networks, together with the UCI concept.
Abstract: Semiconductor detector arrays are widely used in
high-temperature plasma diagnostics. They have a fast response,
which allows observation of many processes and instabilities in
tokamaks. In this paper, there are reviewed several diagnostics based
on semiconductor arrays as cameras, AXUV photodiodes (referred
often as fast “bolometers") and detectors of both soft X-rays and
visible light installed on the COMPASS tokamak recently. Fresh
results from both spring and summer campaigns in 2012 are
introduced. Examples of the utilization of the detectors are shown on
the plasma shape determination, fast calculation of the radiation
center, two-dimensional plasma radiation tomography in different
spectral ranges, observation of impurity inflow, and also on
investigation of MHD activity in the COMPASS tokamak discharges.
Abstract: The increasing complexity of software development based on peer to peer networks makes necessary the creation of new frameworks in order to simplify the developer-s task. Additionally, some applications, e.g. fire detection or security alarms may require real-time constraints and the high level definition of these features eases the application development. In this paper, a service model based on a component model with real-time features is proposed. The high-level model will abstract developers from implementation tasks, such as discovery, communication, security or real-time requirements. The model is oriented to deploy services on small mobile devices, such as sensors, mobile phones and PDAs, where the computation is light-weight. Services can be composed among them by means of the port concept to form complex ad-hoc systems and their implementation is carried out using a component language called UM-RTCOM. In order to apply our proposals a fire detection application is described.
Abstract: NFκB activation plays a crucial role in anti-apoptotic responses in response to the apoptotic signaling during tumor necrosis factor (TNFa) stimulation in Multiple Myeloma (MM). Although several drugs have been found effective for the treatment of MM by mainly inhibiting NFκB pathway, there are no any quantitative or qualitative results of comparison assessment on inhibition effect between different single drugs or drug combinations. Computational modeling is becoming increasingly indispensable for applied biological research mainly because it can provide strong quantitative predicting power. In this study, a novel computational pathway modeling approach is employed to comparably assess the inhibition effects of specific single drugs and drug combinations on the NFκB pathway in MM, especially the prediction of synergistic drug combinations.
Abstract: Silver nano-particles have been used for antibacterial
purpose and it is also believed to have removal of odorous compounds,
oxidation capacity as a metal catalyst. In this study, silver
nano-particles in nano sizes (5-30 nm) were prepared on the surface of
NaHCO3, the supporting material, using a sputtering method that
provided high silver content and minimized conglomerating problems
observed in the common AgNO3 photo-deposition method. The silver
nano-particles were dispersed by dissolving Ag-NaHCO3 into water,
and the dispersed silver nano-particles in the aqueous phase were
applied to remove inorganic odor compounds, H2S, in a scrubbing
reactor. Hydrogen sulfide in the gas phase was rapidly removed by the
silver nano-particles, and the concentration of sulfate (SO4
2-) ion
increased with time due to the oxidation reaction by silver as a
catalyst. Consequently, the experimental results demonstrated that the
silver nano-particles in the aqueous solution can be successfully
applied to remove odorous compounds without adding additional
energy sources and producing any harmful byproducts
Abstract: Trihalomethanes (THMs) were among the first
disinfection byproducts to be discovered in chlorinated water. The
substances form during a reaction between chlorine and organic
matter in the water. Trihalomethanes are suspected to have negative
effects on birth such as, low birth weight, intrauterine growth
retardation in term births, as well as gestational age and preterm
delivery. There are also some evidences showing these by-products to
be mutagenic and carcinogenic, the greatest amount of evidence being
related to the bladder cancer. However, there exist inconsistencies
regarding such effects of THMs as different studies have provided
different results in this regard. The aim of the present study is to
provide a review of the related researches about the above mentioned
health effects of THMs.
Abstract: This paper simulates the ad-hoc mesh network in rural areas, where such networks receive great attention due to their cost, since installing the infrastructure for regular networks in these areas is not possible due to the high cost. The distance between the communicating nodes is the most obstacles that the ad-hoc mesh network will face. For example, in Terranet technology, two nodes can communicate if they are only one kilometer far from each other. However, if the distance between them is more than one kilometer, then each node in the ad-hoc mesh networks has to act as a router that forwards the data it receives to other nodes. In this paper, we try to find the critical number of nodes which makes the network fully connected in a particular area, and then propose a method to enhance the intermediate node to accept to be a router to forward the data from the sender to the receiver. Much work was done on technological changes on peer to peer networks, but the focus of this paper will be on another feature which is to find the minimum number of nodes needed for a particular area to be fully connected and then to enhance the users to switch on their phones and accept to work as a router for other nodes. Our method raises the successful calls to 81.5% out of 100% attempt calls.
Abstract: Environmental awareness and depletion of the
petroleum resources are among vital factors that motivate a number
of researchers to explore the potential of reusing natural fiber as an
alternative composite material in industries such as packaging,
automotive and building constructions. Natural fibers are available in
abundance, low cost, lightweight polymer composite and most
importance its biodegradability features, which often called “ecofriendly"
materials. However, their applications are still limited due
to several factors like moisture absorption, poor wettability and large
scattering in mechanical properties. Among the main challenges on
natural fibers reinforced matrices composite is their inclination to
entangle and form fibers agglomerates during processing due to
fiber-fiber interaction. This tends to prevent better dispersion of the
fibers into the matrix, resulting in poor interfacial adhesion between
the hydrophobic matrix and the hydrophilic reinforced natural fiber.
Therefore, to overcome this challenge, fiber treatment process is one
common alternative that can be use to modify the fiber surface
topology by chemically, physically or mechanically technique.
Nevertheless, this paper attempt to focus on the effect of
mercerization treatment on mechanical properties enhancement of
natural fiber reinforced composite or so-called bio composite. It
specifically discussed on mercerization parameters, and natural fiber
reinforced composite mechanical properties enhancement.
Abstract: The study analyzed the risk and returns of commercial-property in Southwestern Nigeria and selected stocksmarket investment between 2000 and 2009; compared the inflation hedging characteristics and diversification potentials of investing in commercial-property and selected stock- market investment. Primary data were collected on characteristics, rental and capital values of commercial- properties from their property managers through the use of questionnaire. Secondary data on stock prices and dividends on banking, insurance and conglomerates sectors were sourced from the Nigerian Stock Exchange (2000-2009). The result showed that average return on all the selected stock- investments was higher than that of commercial-property. As regards risk, commercial-property indicated lower risk, compared to stocks. Also the stock-investment had better inflation hedging capacity than commercial-properties; combination of both had diversification potentials. The study concluded that stock-market investment offered attractive higher return than commercial-property although with higher risk and there could be diversification benefits in combining commercial-property with stock- investment.
Abstract: A genetic algorithm (GA) based feature subset
selection algorithm is proposed in which the correlation structure of
the features is exploited. The subset of features is validated according
to the classification performance. Features derived from the
continuous wavelet transform are potentially strongly correlated.
GA-s that do not take the correlation structure of features into
account are inefficient. The proposed algorithm forms clusters of
correlated features and searches for a good candidate set of clusters.
Secondly a search within the clusters is performed. Different
simulations of the algorithm on a real-case data set with strong
correlations between features show the increased classification
performance. Comparison is performed with a standard GA without
use of the correlation structure.
Abstract: Seemingly simple probabilities in the m-player game bingo have never been calculated. These probabilities include expected game length and the expected number of winners on a given turn. The difficulty in probabilistic analysis lies in the subtle interdependence among the m-many bingo game cards in play. In this paper, the game i got it!, a bingo variant, is considered. This variation provides enough weakening of the inter-player dependence to allow probabilistic analysis not possible for traditional bingo. The probability of winning in exactly k turns is calculated for a one-player game. Given a game of m-many players, the expected game length and tie probability are calculated. With these calculations, the game-s interesting payout scheme is considered.
Abstract: A new code synchronization algorithm is proposed in
this paper for the secondary cell-search stage in wideband CDMA
systems. Rather than using the Cyclically Permutable (CP) code in the
Secondary Synchronization Channel (S-SCH) to simultaneously
determine the frame boundary and scrambling code group, the new
synchronization algorithm implements the same function with less
system complexity and less Mean Acquisition Time (MAT). The
Secondary Synchronization Code (SSC) is redesigned by splitting into
two sub-sequences. We treat the information of scrambling code group
as data bits and use simple time diversity BCH coding for further
reliability. It avoids involved and time-costly Reed-Solomon (RS)
code computations and comparisons. Analysis and simulation results
show that the Synchronization Error Rate (SER) yielded by the new
algorithm in Rayleigh fading channels is close to that of the
conventional algorithm in the standard. This new synchronization
algorithm reduces system complexities, shortens the average
cell-search time and can be implemented in the slot-based cell-search
pipeline. By taking antenna diversity and pipelining correlation
processes, the new algorithm also shows its flexible application in
multiple antenna systems.
Abstract: Unlike general-purpose processors, digital signal
processors (DSP processors) are strongly application-dependent. To
meet the needs for diverse applications, a wide variety of DSP
processors based on different architectures ranging from the
traditional to VLIW have been introduced to the market over the
years. The functionality, performance, and cost of these processors
vary over a wide range. In order to select a processor that meets the
design criteria for an application, processor performance is usually
the major concern for digital signal processing (DSP) application
developers. Performance data are also essential for the designers of
DSP processors to improve their design. Consequently, several DSP
performance benchmarks have been proposed over the past decade or
so. However, none of these benchmarks seem to have included recent
new DSP applications.
In this paper, we use a new benchmark that we recently developed
to compare the performance of popular DSP processors from Texas
Instruments and StarCore. The new benchmark is based on the
Selectable Mode Vocoder (SMV), a speech-coding program from the
recent third generation (3G) wireless voice applications. All
benchmark kernels are compiled by the compilers of the respective
DSP processors and run on their simulators. Weighted arithmetic
mean of clock cycles and arithmetic mean of code size are used to
compare the performance of five DSP processors.
In addition, we studied how the performance of a processor is
affected by code structure, features of processor architecture and
optimization of compiler. The extensive experimental data gathered,
analyzed, and presented in this paper should be helpful for DSP
processor and compiler designers to meet their specific design goals.