Abstract: This paper presents a hybrid electric scooter model developed and simulated using Matlab/Simulink. This hybrid scooter modeled has a parallel hybrid structure. The main propulsion units consist of a two stroke internal combustion engine and a hub motor attached to the front wheel of the scooter. The methodology used to optimize the energy and fuel consumption of the hybrid electric scooter is the multi-mode approach. Various case studies were presented to check the model and were compared to the literatures. Results shown that the model developed was feasible and valuable.
Abstract: This paper deals with new concept of using compressed atmospheric air as a zero pollution power source for running motorbikes. The motorbike is equipped with an air turbine in place of an internal combustion engine, and transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor to casing diameter ratios with respect to different vane angles (number of vanes) have been considered and analyzed. It is found that the shaft work output is optimum for some typical values of rotor / casing diameter ratios at a particular value of vane angle (no. of vanes). In this study, the maximum power is obtained as 4.5kW - 5.3kW (5.5-6.25 HP) when casing diameter is taken 100 mm, and rotor to casing diameter ratios are kept from 0.65 to 0.55. This value of output is sufficient to run motorbike.
Abstract: The greenhouse effect and limitations on carbon
dioxide emissions concern engine maker and the future of the
internal combustion engines should go toward substantially and
improved thermal efficiency engine. Homogeneous charge
compression ignition (HCCI) is an alternative high-efficiency
technology for combustion engines to reduce exhaust emissions and
fuel consumption. However, there are still tough challenges in the
successful operation of HCCI engines, such as controlling the
combustion phasing, extending the operating range, and high
unburned hydrocarbon and CO emissions. HCCI and the exploitation
of ethanol as an alternative fuel is one way to explore new frontiers
of internal combustion engines with an eye towards maintaining its
sustainability. This study was done to extend database knowledge
about HCCI with ethanol a fuel.
Abstract: This paper investigates the effect of replacing
crankshaft with cam on the indicated torque during compression and
power strokes in internal combustion engines. A Cycloidal cam
profile was used in Revetec engine to calculate and compare the
torque to a conventional engine, using a computational method.
Firstly, the cylinder pressure was calculated using Ferguson equation,
and then the torque calculated depending on cylinder pressure values
in every crank angle. the results showed that by using Cycloidal cam
profile in Revetec engine the torque can increased by 14% compared
with conventional engines, which means an increase in engine
efficiency.
Abstract: Homogeneous Charge Compression (HCCI) Ignition technology has been around for a long time, but has recently received renewed attention and enthusiasm. This paper deals with experimental investigations of HCCI engine using hydrous methanol as a primary fuel and Dimethyl Ether (DME) as an ignition improver. A regular diesel engine has been modified to work as HCCI engine for this investigation. The hydrous methanol is inducted and DME is injected into a single cylinder engine. Hence, hydrous methanol is used with 15% water content in HCCI engine and its performance and emission behavior is documented. The auto-ignition of Methanol is enabled by DME. The quantity of DME varies with respect to the load. In this study, the experiments are conducted independently and the effect of the hydrous methanol on the engine operating limit, heat release rate and exhaust emissions at different load conditions are investigated. The investigation also proves that the Hydrous Methanol with DME operation reduces the oxides of Nitrogen and smoke to an extreme low level which is not possible by the direct injection CI engine. Therefore, it is beneficial to use hydrous methanol-DME HCCI mode while using hydrous methanol in internal Combustion Engines.
Abstract: This paper presents an environmental and technoeconomic
evaluation of light duty vehicles in Iran. A comprehensive
well-to-wheel (WTW) analysis is applied to compare different
automotive fuel chains, conventional internal combustion engines and
innovative vehicle powertrains. The study examines the
competitiveness of 15 various pathways in terms of energy
efficiencies, GHG emissions, and levelized cost of different energy
carriers. The results indicate that electric vehicles including battery
electric vehicles (BEV), fuel cell vehicles (FCV) and plug-in hybrid
electric vehicles (PHEV) increase the WTW energy efficiency by
54%, 51% and 46%, respectively, compared to common internal
combustion engines powered by gasoline. On the other hand,
greenhouse gas (GHG) emissions per kilometer of FCV and BEV
would be 48% lower than that of gasoline engines. It is concluded
that BEV has the lowest total cost of energy consumption and
external cost of emission, followed by internal combustion engines
(ICE) fueled by CNG. Conventional internal combustion engines
fueled by gasoline, on the other hand, would have the highest costs.
Abstract: This paper presents modern vibration signalprocessing
techniques for vehicle gearbox fault diagnosis, via the
wavelet analysis and the Squared Envelope (SE) technique. The
wavelet analysis is regarded as a powerful tool for the detection of
sudden changes in non-stationary signals. The Squared Envelope
(SE) technique has been extensively used for rolling bearing
diagnostics. In the present work a scheme of using the Squared
Envelope technique for early detection of gear tooth pit. The pitting
defect is manufactured on the tooth side of a fifth speed gear on the
intermediate shaft of a vehicle gearbox. The objective is to
supplement the current techniques of gearbox fault diagnosis based
on using the raw vibration and ordered signals. The test stand is
equipped with three dynamometers; the input dynamometer serves as
the internal combustion engine, the output dynamometers introduce
the load on the flanges of output joint shafts. The gearbox used for
experimental measurements is the type most commonly used in
modern small to mid-sized passenger cars with transversely mounted
powertrain and front wheel drive; a five-speed gearbox with final
drive gear and front wheel differential. The results show that the
approaches methods are effective for detecting and diagnosing
localized gear faults in early stage under different operation
conditions, and are more sensitive and robust than current gear
diagnostic techniques.
Abstract: Partial combustion of biomass in the gasifier generates producer gas that can be used for heating purposes and as supplementary or sole fuel in internal combustion engines. In this study, the virgin biomass obtained from hingan shell is used as the feedstock for gasifier to generate producer gas. The gasifier-engine system is operated on diesel and on esters of vegetable oil of hingan in liquid fuel mode operation and then on liquid fuel and producer gas combination in dual fuel mode operation. The performance and emission characteristics of the CI engine is analyzed by running the engine in liquid fuel mode operation and in dual fuel mode operation at different load conditions with respect to maximum diesel savings in the dual fuel mode operation. It was observed that specific energy consumption in the dual fuel mode of operation is found to be in the higher side at all load conditions. The brake thermal efficiency of the engine using diesel or hingan oil methyl ester (HOME) is higher than that of dual fuel mode operation. A diesel replacement in the tune of 60% in dual fuel mode is possible with the use of hingan shell producer gas. The emissions parameters such CO, HC, NOx, CO2 and smoke are higher in the case of dual fuel mode of operation as compared to that of liquid fuel mode.
Abstract: Due to the stringent legislation for emission of diesel
engines and also increasing demand on fuel consumption, the
importance of detailed 3D simulation of fuel injection, mixing and
combustion have been increased in the recent years. In the present
work, FIRE code has been used to study the detailed modeling of
spray and mixture formation in a Caterpillar heavy-duty diesel
engine. The paper provides an overview of the submodels
implemented, which account for liquid spray atomization, droplet
secondary break-up, droplet collision, impingement, turbulent
dispersion and evaporation. The simulation was performed from
intake valve closing (IVC) to exhaust valve opening (EVO). The
predicted in-cylinder pressure is validated by comparing with
existing experimental data. A good agreement between the predicted
and experimental values ensures the accuracy of the numerical
predictions collected with the present work. Predictions of engine
emissions were also performed and a good quantitative agreement
between measured and predicted NOx and soot emission data were
obtained with the use of the present Zeldowich mechanism and
Hiroyasu model. In addition, the results reported in this paper
illustrate that the numerical simulation can be one of the most
powerful and beneficial tools for the internal combustion engine
design, optimization and performance analysis.