Abstract: In the last decades, the problem of perforation
damage has been considered as the major factor for the
reduction of oil productivity. Underbalance perforation is
considered as one of the best means to minimize or overcome
this problem. By maintaining wellbore pressure lower than
formation pressure, perforation damage could be minimize or
eliminated. This can be achieved by the use of nontraditional
lightweight completion fluid. This paper presents the effect of
natural clay in formulating nontraditional completion fluid to
ensure successful perforation job and increase of production
rate. Natural clay is used as homogenizing agent to create a
stable and non-damaging low-density completion fluid.
Results indicate that the addition of natural clay dramatically
increase the stability of the final fluids. In addition, field test
has shown that the application of nontraditional completion
fluid increases oil production by three folds.
Abstract: Anaerobic Digestion has become a promising
technology for biological transformation of organic fraction of the
municipal solid wastes (MSW). In order to represent the kinetic
behavior of such biological process and thereby to design a reactor
system, development of a mathematical model is essential.
Addressing this issue, a simplistic mathematical model has been
developed for anaerobic digestion of MSW in a continuous flow
reactor unit under homogeneous steady state condition. Upon
simulated hydrolysis, the kinetics of biomass growth and substrate
utilization rate are assumed to follow first order reaction kinetics.
Simulation of this model has been conducted by studying sensitivity
of various process variables. The model was simulated using typical
kinetic data of anaerobic digestion MSW and typical MSW
characteristics of Kolkata. The hydraulic retention time (HRT) and
solid retention time (SRT) time were mainly estimated by varying
different model parameters like efficiency of reactor, influent
substrate concentration and biomass concentration. Consequently,
design table and charts have also been prepared for ready use in the
actual plant operation.
Abstract: Micro droplet formation is considered as a growing
emerging area of research due to its wide-range application in
chemistry as well as biology. The mechanism of micro droplet
formation using two immiscible liquids running through a T-junction
has been widely studied.
We believe that the flow of these two immiscible phases can be of
greater important factor that could have an impact on out-flow
hydrodynamic behavior, the droplets generated and the size of the
droplets. In this study, the type of the capillary tubes used also
represents another important factor that can have an impact on the
generation of micro droplets.
The tygon capillary tubing with hydrophilic inner surface doesn't
allow regular out-flows due to the fact that the continuous phase
doesn't adhere to the wall of the capillary inner surface.
Teflon capillary tubing, presents better wettability than tygon
tubing, and allows to obtain steady and regular regimes of out-flow,
and the micro droplets are homogeneoussize.
The size of the droplets is directly dependent on the flows of the
continuous and dispersed phases. Thus, as increasing the flow of the
continuous phase, to flow of the dispersed phase stationary, the size
of the drops decreases. Inversely, while increasing the flow of the
dispersed phase, to flow of the continuous phase stationary, the size
of the droplet increases.
Abstract: Purpose: Planning and dosimetry of different VMAT algorithms (SmartArc, Ergo++, Autobeam) is compared with IMRT for Head and Neck Cancer patients. Modelling was performed to rule out the causes of discrepancies between planned and delivered dose. Methods: Five HNC patients previously treated with IMRT were re-planned with SmartArc (SA), Ergo++ and Autobeam. Plans were compared with each other and against IMRT and evaluated using DVHs for PTVs and OARs, delivery time, monitor units (MU) and dosimetric accuracy. Modelling of control point (CP) spacing, Leaf-end Separation and MLC/Aperture shape was performed to rule out causes of discrepancies between planned and delivered doses. Additionally estimated arc delivery times, overall plan generation times and effect of CP spacing and number of arcs on plan generation times were recorded. Results: Single arc SmartArc plans (SA4d) were generally better than IMRT and double arc plans (SA2Arcs) in terms of homogeneity and target coverage. Double arc plans seemed to have a positive role in achieving improved Conformity Index (CI) and better sparing of some Organs at Risk (OARs) compared to Step and Shoot IMRT (ss-IMRT) and SA4d. Overall Ergo++ plans achieved best CI for both PTVs. Dosimetric validation of all VMAT plans without modelling was found to be lower than ss-IMRT. Total MUs required for delivery were on average 19%, 30%, 10.6% and 6.5% lower than ss-IMRT for SA4d, SA2d (Single arc with 20 Gantry Spacing), SA2Arcs and Autobeam plans respectively. Autobeam was most efficient in terms of actual treatment delivery times whereas Ergo++ plans took longest to deliver. Conclusion: Overall SA single arc plans on average achieved best target coverage and homogeneity for both PTVs. SA2Arc plans showed improved CI and some OARs sparing. Very good dosimetric results were achieved with modelling. Ergo++ plans achieved best CI. Autobeam resulted in fastest treatment delivery times.
Abstract: This paper investigates the issue of building decision
trees from data with imprecise class values where imprecision is
encoded in the form of possibility distributions. The Information
Affinity similarity measure is introduced into the well-known gain
ratio criterion in order to assess the homogeneity of a set of
possibility distributions representing instances-s classes belonging to
a given training partition. For the experimental study, we proposed an
information affinity based performance criterion which we have used
in order to show the performance of the approach on well-known
benchmarks.
Abstract: The necessity of updating the numerical models inputs, because of geometrical and resistive variations in rivers subject to solid transport phenomena, requires detailed control and monitoring activities. The human employment and financial resources of these activities moves the research towards the development of expeditive methodologies, able to evaluate the outflows through the measurement of more easily acquirable sizes. Recent studies highlighted the dependence of the entropic parameter on the kinematical and geometrical flow conditions. They showed a meaningful variability according to the section shape, dimension and slope. Such dependences, even if not yet well defined, could reduce the difficulties during the field activities, and also the data elaboration time. On the basis of such evidences, the relationships between the entropic parameter and the geometrical and resistive sizes, obtained through a large and detailed laboratory experience on steady free surface flows in conditions of macro and intermediate homogeneous roughness, are analyzed and discussed.
Abstract: A satured liquid is warmed until boiling in a parallelepipedic boiler. The heat is supplied in a liquid through the horizontal bottom of the boiler, the other walls being adiabatic. During the process of boiling, the liquid evaporates through its free surface by deforming it. This surface which subdivides the boiler into two regions occupied on both sides by the boiled liquid (broth) and its vapor which surmounts it. The broth occupying the region and its vapor the superior region. A two- fluids model is used to describe the dynamics of the broth, its vapor and their interface. In this model, the broth is treated as a monophasic fluid (homogeneous model) and form with its vapor adiphasic pseudo fluid (two-fluid model). Furthermore, the interface is treated as a zone of mixture characterized by superficial void fraction noted α* . The aim of this article is to describe the dynamics of the interface between the boiled fluid and its vapor within a boiler. The resolution of the problem allowed us to show the evolution of the broth and the level of the liquid.
Abstract: In the present study, a heterogeneous and
homogeneous gas flow dispersion model for simulation and
optimisation of a large-scale catalytic slurry reactor for the direct
synthesis of dimethyl ether (DME) from syngas and CO2, using a
churn-turbulent regime was developed. In the heterogeneous gas flow
model the gas phase was distributed into two bubble phases: small
and large, however in the homogeneous one, the gas phase was
distributed into only one large bubble phase. The results indicated
that the heterogeneous gas flow model was in more agreement with
experimental pilot plant data than the homogeneous one.
Abstract: Measurement of competitiveness between countries or regions is an important topic of many economic analysis and scientific papers. In European Union (EU), there is no mainstream approach of competitiveness evaluation and measuring. There are many opinions and methods of measurement and evaluation of competitiveness between states or regions at national and European level. The methods differ in structure of using the indicators of competitiveness and ways of their processing. The aim of the paper is to analyze main sources of competitive potential of the EU Member States with the help of Factor analysis (FA) and to classify the EU Member States to homogeneous units (clusters) according to the similarity of selected indicators of competitiveness factors by Cluster analysis (CA) in reference years 2000 and 2011. The theoretical part of the paper is devoted to the fundamental bases of competitiveness and the methodology of FA and CA methods. The empirical part of the paper deals with the evaluation of competitiveness factors in the EU Member States and cluster comparison of evaluated countries by cluster analysis.
Abstract: β-Glucosidase is an important enzyme for production
of ethanol from lignocellulose. With hydrolytic activity on
cellooligosaccharides, especially cellobiose, β-glucosidase removes
product inhibitory effect on cellulases and forms fermentable sugars.
In this study, β-glucosidase encoding gene (BGL1) from traditional
starter yeast Saccharomycosis fibuligera BMQ908 was cloned and
expressed in Pichia pastoris. BGL1 of S. fibuligera BMQ 908 shared
98% nucleotide homology with the closest GenBank sequence
(M22475) but identity in amino-acid sequences of catalytic domains.
Recombinant plasmid pPICZαA/BGL1 containing the sequence
encoding BGL1 mature protein and α-factor secretion signal was
constructed and transformed into methylotrophic yeast P. pastoris by
electroporation. The recombinant strain produced single extracellular
protein with molecular weight of 120 kDa and cellobiase activity of
60 IU/ml. The optimum pH of the recombinant β-glucosidase was 5.0
and the optimum temperature was 50°C.
Abstract: Within the framework of a method of the information
theory it is offered statistics and probabilistic model for definition of
cause-and-effect relations in the coupled multicomponent
subsystems. The quantitative parameter which is defined through
conditional and unconditional entropy functions is introduced. The
method is applied to the analysis of the experimental data on
dynamics of change of the chemical elements composition of plants
organs (roots, reproductive organs, leafs and stems). Experiment is
directed on studying of temporal processes of primary soil formation
and their connection with redistribution dynamics of chemical
elements in plant organs. This statistics and probabilistic model
allows also quantitatively and unambiguously to specify the
directions of the information streams on plant organs.
Abstract: The hydromagnetic flow of a Maxwell fluid past a vertical stretching sheet with thermophoresis is considered. The impact of chemical reaction species to the flow is analyzed for the first time by using the homotopy analysis method (HAM). The h-curves for the flow boundary layer equations are presented graphically. Several values of wall skin friction, heat and mass transfer are obtained and discussed.
Abstract: In this study, we developed a model to predict the
temperature and the pressure variation in an internal combustion
engine operated in HCCI (Homogeneous charge compression ignition)
mode. HCCI operation begins from aspirating of homogeneous charge
mixture through intake valve like SI (Spark ignition) engine and the
premixed charge is compressed until temperature and pressure of
mixture reach autoignition point like diesel engine. Combustion phase
was described by double-Wiebe function. The single zone model
coupled with an double-Wiebe function were performed to simulated
pressure and temperature between the period of IVC (Inlet valve close)
and EVO (Exhaust valve open). Mixture gas properties were
implemented using STANJAN and transfer the results to main model.
The model has considered the engine geometry and enables varying in
fuelling, equivalence ratio, manifold temperature and pressure. The
results were compared with the experiment and showed good
correlation with respect to combustion phasing, pressure rise, peak
pressure and temperature. This model could be adapted and use to
control start of combustion for HCCI engine.
Abstract: The purpose of this study is to revisit the concept of
rape as represented by professionals in the literature as well as its
perception (beliefs and attitudes) in the population at large and to
propose methodological improvements to its measurement tool. Rape
is a serious crime threatening its victim-s physical and mental health
and integrity; and as such is legally prosecuted in all modern
societies. The problem is not in accepting or rejecting rape as a
criminal act, but rather in the vagueness of its interpretations and
“justifications" maintained in the mentality of modern societies -
known in the literature as the phenomenon of "rape-myth". The rapemyth
can be studied from different perspectives: criminology,
sociology, ethics, medicine and psychology. Its investigation requires
rigorous scientific objectivity, free of passion (victims of rape are at
risk of emotional bias), free of activism (social activists, even if wellintentioned
are also biased), free of any pre-emptive assumptions or
prejudices. To apply a rigorous scientific procedure, we need a solid,
valid and reliable measurement. Rape is a form of heterosexual or
homosexual aggression, violently forcing the victim to give-in in the
sexual activity of the aggressor against her/his will. Human beings
always try to “understand" or find a reason justifying their acts.
Psychological literature provides multiple clinical and experimental
examples of it; just to mention the famous studies by Milgram on the
level of electroshock delivered by the “teacher" towards the “learner"
if “scientifically justifiable" or the studies on the behavior of
“prisoners" and the “guards" and many other experiments and field
observations. Sigmund Freud presented the phenomenon of
unconscious justification and called it rationalization. The multiple
justifications, rationalizations and repeated opinions about sexual
behavior contribute to a myth maintained in the society. What kind of
“rationale" our societies apply to “understand" the non-consensual
sexual behavior? There are many, just to mention few:
• Sex is a ludistic activity for both participants, therefore –
even if not consented – it should bring pleasure to both.
• Everybody wants sex, but only men are allowed to manifest
it openly while women have to pretend the opposite, thus men have
to initiate sexual behavior and women would follow.
• A person who strongly needs sex is free to manifest it and
struggle to get it; the person who doesn-t want it must not reveal
her/his sexual attraction and avoid risky situations; otherwise she/he
is perceived as a promiscuous seducer.
• A person who doesn-t fight against the sexual initiator
unconsciously accepts the rape (does it explain why homosexual
rapes are reported less frequently than rapes against women?).
• Women who are raped deserve it because their wardrobe is
very revealing and seducing and they ''willingly'' go to highly risky
places (alleys, dark roads, etc.).
• Men need to ventilate their sexual energy and if they are
deprived of a partner their urge to have sex is difficult to control.
• Men are supposed to initiate and insist even by force to have
sex (their testosterone makes them both sexual and aggressive).
The paper overviews numerous cultural beliefs about masculine
versus feminine behavior and their impact on the “rape myth".
Abstract: In this work, Experimental tie-line results and
solubility (binodal) curves were obtained for the ternary systems
(water + acetic acid + methyl isobutyl ketone (MIBK)), (water +
lactic acid+ methyl isobutyl ketone) at T = 294.15K and atmospheric
pressure. The consistency of the values of the experimental tie-lines
was determined through the Othmer-Tobias and Hands correlations.
For the extraction effectiveness of solvents, the distribution and
selectivity curves were plotted. In addition, these experimental tieline
data were also correlated with NRTL model. The interaction
parameters for the NRTL model were retrieved from the obtained
experimental results by means of a combination of the homotopy
method and the genetic algorithms.
Abstract: The combustion of liquid fuel in the porous burner
(PB) was experimented to investigate evaporation mechanism and
combustion behavior. The diesel oil was used as fuel and the pebbles
carefully chosen in the same size like the solid sphere homogeneously
was adopted as the porous media. Two structures of the liquid porous
burner, i.e. the PB without and with installation of porous emitter
(PE), were performed. PE was installed by lower than PB with
distance of 20 cm. The pebbles having porosity (φ) of 0.45 and 0.52
were, respectively, used in PB and PE. The fuel was supplied dropwise
from the top through the PB and the combustion was occurred between
PB and PE. Axial profiles of temperature along the burner length were
measured to clarify the evaporation and combustion phenomena. The
pollutant emission characteristics were monitored at the burner exit.
From the experiment, it was found that the temperature profiles of both
structures decreased with the three ways swirling air flows (QA)
increasing. On the other hand, the temperature profiles increased with
fuel heat input (QF). Obviously, the profile of the porous burner
installed with PE was higher than that of the porous burner without
PE
Abstract: in dissimilar material joints, failure often occurs
along the interface between two materials due to stress singularity.
Stress distribution and its concentration depend on materials and
geometry of the junction. Inhomogenity of stress distribution at the
interface of junction of two materials with different elastic modules
and stress concentration in this zone are the main factors resulting in
rupture of the junction. Effect of joining angle in the interface of
aluminum-polycarbonate will be discussed in this paper. Computer
simulation and finite element analysis by ABAQUS showed that
convex interfacial joint leads to stress reduction at junction corners in
compare with straight joint. This finding is confirmed by photoelastic
experimental results.
Abstract: The notion of S-fuzzy left h-ideals in a hemiring is introduced and it's basic properties are investigated.We also study the homomorphic image and preimage of S-fuzzy left h-ideal of hemirings.Using a collection of left h-ideals of a hemiring, S-fuzzy left h-ideal of hemirings are established.The notion of a finite-valued S-fuzzy left h-ideal is introduced,and its characterization is given.S-fuzzy relations on hemirings are discussed.The notion of direct product and S-product are introduced and some properties of the direct product and S-product of S-fuzzy left h-ideal of hemiring are also discussed.
Abstract: Reactiondiffusion systems are mathematical models that describe how the concentration of one or more substances distributed in space changes under the influence of local chemical reactions in which the substances are converted into each other, and diffusion which causes the substances to spread out in space. The classical representation of a reaction-diffusion system is given by semi-linear parabolic partial differential equations, whose general form is ÔêétX(x, t) = DΔX(x, t), where X(x, t) is the state vector, D is the matrix of the diffusion coefficients and Δ is the Laplace operator. If the solute move in an homogeneous system in thermal equilibrium, the diffusion coefficients are constants that do not depend on the local concentration of solvent and of solutes and on local temperature of the medium. In this paper a new stochastic reaction-diffusion model in which the diffusion coefficients are function of the local concentration, viscosity and frictional forces of solvent and solute is presented. Such a model provides a more realistic description of the molecular kinetics in non-homogenoeus and highly structured media as the intra- and inter-cellular spaces. The movement of a molecule A from a region i to a region j of the space is described as a first order reaction Ai k- → Aj , where the rate constant k depends on the diffusion coefficient. Representing the diffusional motion as a chemical reaction allows to assimilate a reaction-diffusion system to a pure reaction system and to simulate it with Gillespie-inspired stochastic simulation algorithms. The stochastic time evolution of the system is given by the occurrence of diffusion events and chemical reaction events. At each time step an event (reaction or diffusion) is selected from a probability distribution of waiting times determined by the specific speed of reaction and diffusion events. Redi is the software tool, developed to implement the model of reaction-diffusion kinetics and dynamics. It is a free software, that can be downloaded from http://www.cosbi.eu. To demonstrate the validity of the new reaction-diffusion model, the simulation results of the chaperone-assisted protein folding in cytoplasm obtained with Redi are reported. This case study is redrawing the attention of the scientific community due to current interests on protein aggregation as a potential cause for neurodegenerative diseases.
Abstract: Homogeneous Charge Compression (HCCI) Ignition technology has been around for a long time, but has recently received renewed attention and enthusiasm. This paper deals with experimental investigations of HCCI engine using hydrous methanol as a primary fuel and Dimethyl Ether (DME) as an ignition improver. A regular diesel engine has been modified to work as HCCI engine for this investigation. The hydrous methanol is inducted and DME is injected into a single cylinder engine. Hence, hydrous methanol is used with 15% water content in HCCI engine and its performance and emission behavior is documented. The auto-ignition of Methanol is enabled by DME. The quantity of DME varies with respect to the load. In this study, the experiments are conducted independently and the effect of the hydrous methanol on the engine operating limit, heat release rate and exhaust emissions at different load conditions are investigated. The investigation also proves that the Hydrous Methanol with DME operation reduces the oxides of Nitrogen and smoke to an extreme low level which is not possible by the direct injection CI engine. Therefore, it is beneficial to use hydrous methanol-DME HCCI mode while using hydrous methanol in internal Combustion Engines.