Abstract: Safety of bus journey is a fundamental concern. Risk of injuries and fatalities is severe when bus superstructure fails during rollover accident. Adequate design and sufficient strength of bus superstructure can reduce the number of injuries and fatalities. This paper deals with structural analysis of bus superstructure undergoes rollover event. Several value of mass will be varied in multiple simulations. The purpose of this work is to analyze structural response of bus superstructure in terms of deformation, stress and strain under several loading and constraining conditions. A complete bus superstructure with forty four passenger-s capability was developed using finite element analysis software. Simulations have been conducted to observe the effect of total mass of bus on the strength of superstructure. These simulations are following United Nation Economic Commission of Europe regulation 66 which focuses on strength of large vehicle superstructure. Validation process had been done using simple box model experiment and results obtained are comparing with simulation results. Inputs data from validation process had been used in full scale simulation. Analyses suggested that, the failure of bus superstructure during rollover situation is basically dependent on the total mass of bus and on the strength of bus superstructure.
Abstract: This paper presents the development of adaptive
distance relay for protection of parallel transmission line with mutual
coupling. The proposed adaptive relay, automatically adjusts its
operation based on the acquisition of the data from distance relay of
adjacent line and status of adjacent line from line circuit breaker IED
(Intelligent Electronic Device). The zero sequence current of the
adjacent parallel transmission line is used to compute zero sequence
current ratio and the mutual coupling effect is fully compensated.
The relay adapts to changing circumstances, like failure in
communication from other relays and non - availability of adjacent
transmission line. The performance of the proposed adaptive relay is
tested using steady state and dynamic test procedures. The fault
transients are obtained by simulating a realistic parallel transmission
line system with mutual coupling effect in PSCAD. The evaluation
test results show the efficacy of adaptive distance relay over the
conventional distance relay.
Abstract: Software Reliability is one of the key factors in the software development process. Software Reliability is estimated using reliability models based on Non Homogenous Poisson Process. In most of the literature the Software Reliability is predicted only in testing phase. So it leads to wrong decision-making concept. In this paper, two Software Reliability concepts, testing and operational phase are studied in detail. Using S-Shaped Software Reliability Growth Model (SRGM) and Exponential SRGM, the testing and operational reliability values are obtained. Finally two reliability values are compared and optimal release time is investigated.
Abstract: There are various approaches to implement quality
improvements. Organizations aim for a management standard which
is capable of providing customers with quality assurance on their
product/service via continuous process improvement. Carefully
planned steps are necessary to ensure the right quality improvement
methodology (QIM) and business operations are consistent, reliable
and truly meet the customers' needs. This paper traces the evolution
of QIM in Malaysia-s Information Technology (IT) industry in the
past, current and future; and highlights some of the thought of
researchers who contributed to the science and practice of quality,
and identifies leading methodologies in use today. Some of the
misconceptions and mistakes leading to quality system failures will
also be examined and discussed. This paper aims to provide a general
overview of different types of QIMs available for IT businesses in
maximizing business advantages, enhancing product quality,
improving process routines and increasing performance earnings.
Abstract: Cognizant of the fact that enterprise systems involve
organizational change and their implementation is over shadowed by a
high failure rate, it is argued that there is the need to focus attention on
employees- perceptions of such organizational change when
explaining adoption behavior of enterprise systems. For this purpose,
the research incorporates a conceptual constructo fattitude toward
change that captures views about the need for organizational change.
Centered on this conceptual construct, the research model includes
beliefs regarding the system and behavioral intention as its
consequences, and the personal characteristics of organizational
commitment and perceived personal competence as its antecedents.
Structural equation analysis using LISREL provides significant
support for the proposed relationships. Theoretical and practical
implications are discussed along with limitations.
Abstract: Finite element method was applied to model damage
development in the femoral neck during a sideways fall. The femoral
failure was simulated using the maximum principal strain criterion.
The evolution of damage was consistent with previous studies. It was
initiated by compressive failure at the junction of the superior aspect
of the femoral neck and the greater trochanter. It was followed by
tensile failure that occurred at the inferior aspect of the femoral neck
before a complete transcervical fracture was observed. The estimated
failure line was less than 50° from the horizontal plane (Pauwels type
II).
Abstract: Recently studies in area of supply chain network
(SCN) have focused on the disruption issues in distribution systems.
Also this paper extends the previous literature by providing a new biobjective
model for cost minimization of designing a three echelon
SCN across normal and failure scenarios with considering multi
capacity option for manufacturers and distribution centers. Moreover,
in order to solve the problem by means of LINGO software, novel
model will be reformulated through a branch of LP-Metric method
called Min-Max approach.
Abstract: In a product development process, understanding the functional behavior of the system, the role of components in achieving functions and failure modes if components/subsystem fails its required function will help develop appropriate design validation and verification program for reliability assessment. The integration of these three issues will help design and reliability engineers in identifying weak spots in design and planning future actions and testing program. This case study demonstrate the advantage of unascertained theory described in the subjective cognition uncertainty, and then applies blind number (BN) theory in describing the uncertainty of the mechanical system failure process and the same time used the same theory in bringing out another mechanical reliability system model. The practical calculations shows the BN Model embodied the characters of simply, small account of calculation but betterforecasting capability, which had the value of macroscopic discussion to some extent.
Abstract: As originally designed for wired networks, TCP (transmission control protocol) congestion control mechanism is triggered into action when packet loss is detected. This implicit assumption for packet loss mostly due to network congestion does not work well in Mobile Ad Hoc Network, where there is a comparatively high likelihood of packet loss due to channel errors and node mobility etc. Such non-congestion packet loss, when dealt with by congestion control mechanism, causes poor TCP performance in MANET. In this study, we continue to investigate the impact of the interaction between transport protocols and on-demand routing protocols on the performance and stability of 802.11 multihop networks. We evaluate the important wireless networking events caused routing change, and propose a cross layer method to delay the unnecessary routing changes, only need to add a sensitivity parameter α , which represents the on-demand routing-s reaction to link failure of MAC layer. Our proposal is applicable to the plain 802.11 networking environment, the simulation results that this method can remarkably improve the stability and performance of TCP without any modification on TCP and MAC protocol.
Abstract: In this paper, we propose a hardware and software
design method for automotive Electronic Control Units (ECU)
considering the functional safety. The proposed ECU is considered for
the application to Electro-Mechanical Actuator systems and the
validity of the design method is shown by the application to the
Electro-Mechanical Brake (EMB) control system which is used as a
brake actuator in Brake-By-Wire (BBW) systems. The importance of a
functional safety-based design approach to EMB ECU design has been
emphasized because of its safety-critical functions, which are executed
with the aid of many electric actuators, sensors, and application
software. Based on hazard analysis and risk assessment according to
ISO26262, the EMB system should be ASIL-D-compliant, the highest
ASIL level. To this end, an external signature watchdog and an
Infineon 32-bit microcontroller TriCore are used to reduce risks
considering common-cause hardware failure. Moreover, a software
design method is introduced for implementing functional
safety-oriented monitoring functions based on an asymmetric dual
core architecture considering redundancy and diversity. The validity
of the proposed ECU design approach is verified by using the EMB
Hardware-In-the-Loop (HILS) system, which consists of the EMB
assembly, actuator ECU, a host PC, and a few debugging devices.
Furthermore, it is shown that the existing sensor fault tolerant control
system can be used more effectively for mitigating the effects of
hardware and software faults by applying the proposed ECU design
method.
Abstract: Fatigue is the major threat in service of steel structure
subjected to fluctuating loads. With the additional effect of corrosion
and presence of weld joints the fatigue failure may become more
critical in structural steel. One of the apt examples of such structural
is the sailing ship. This is experiencing a constant stress due to
floating and a pulsating bending load due to the waves. This paper
describes an attempt to verify theory of fatigue in fracture mechanics
approach with experimentation to determine the constants of crack
growth curve. For this, specimen is prepared from the ship building
steel and it is subjected to a pulsating bending load with a known
defect. Fatigue crack and its nature is observed in this experiment.
Application of fracture mechanics approach in fatigue with a simple
practical experiment is conducted and constants of crack growth
equation are investigated.
Abstract: This paper presents the effect of corrugation profile
geometry on the crushing behavior, energy absorption, failure
mechanism, and failure mode of woven roving glass fibre/epoxy
laminated composite tube. Experimental investigations were carried
out on composite tubes with three different profile shapes: sinusoidal,
triangular and trapezoidal. The tubes were subjected to lateral
compressive loading. On the addition to a radial corrugated
composite tube, cylindrical composite tube, were fabricated and
tested under the same condition in order to know the effect of
corrugation geometry. Typical histories of their deformation are
presented. Behavior of tubes as regards the peak crushing load,
energy absorbed and mode of crushing has been discussed. The
results show that the behavior of the tube under lateral compression
load is influenced by the geometry of the tube itself.
Abstract: The new idea of this research is application of a new fault detection and isolation (FDI) technique for supervision of sensor networks in transportation system. In measurement systems, it is necessary to detect all types of faults and failures, based on predefined algorithm. Last improvements in artificial neural network studies (ANN) led to using them for some FDI purposes. In this paper, application of new probabilistic neural network features for data approximation and data classification are considered for plausibility check in temperature measurement. For this purpose, two-phase FDI mechanism was considered for residual generation and evaluation.
Abstract: In this paper parametric analytical studies have been carried out to examine the intrinsic flow physics pertaining to the liftoff time of solid propellant rockets. Idealized inert simulators of solid rockets are selected for numerical studies to examining the preignition chamber dynamics. Detailed diagnostic investigations have been carried out using an unsteady two-dimensional k-omega turbulence model. We conjectured from the numerical results that the altered variations of the igniter jet impingement angle, turbulence level, time and location of the first ignition, flame spread characteristics, the overall chamber dynamics including the boundary layer growth history are having bearing on the time for nozzle flow chocking for establishing the required thrust for the rocket liftoff. We concluded that the altered flow choking time of strap-on motors with the pre-determined identical ignition time at the lift off phase will lead to the malfunctioning of the rocket. We also concluded that, in the light of the space debris, an error in predicting the liftoff time can lead to an unfavorable launch window amounts the satellite injection errors and/or the mission failures.
Abstract: Modern manufacturing facilities are large scale,
highly complex, and operate with large number of variables under
closed loop control. Early and accurate fault detection and diagnosis
for these plants can minimise down time, increase the safety of plant
operations, and reduce manufacturing costs. Fault detection and
isolation is more complex particularly in the case of the faulty analog
control systems. Analog control systems are not equipped with
monitoring function where the process parameters are continually
visualised. In this situation, It is very difficult to find the relationship
between the fault importance and its consequences on the product
failure. We consider in this paper an approach to fault detection and
analysis of its effect on the production quality using an adaptive
centring and scaling in the pickling process in cold rolling. The fault
appeared on one of the power unit driving a rotary machine, this
machine can not track a reference speed given by another machine.
The length of metal loop is then in continuous oscillation, this affects
the product quality. Using a computerised data acquisition system,
the main machine parameters have been monitored. The fault has
been detected and isolated on basis of analysis of monitored data.
Normal and faulty situation have been obtained by an artificial neural
network (ANN) model which is implemented to simulate the normal
and faulty status of rotary machine. Correlation between the product
quality defined by an index and the residual is used to quality
classification.
Abstract: Having a very many number of pipelines all over the
country, Iran is one of the countries consists of various ecosystems
with variable degrees of fragility and robusticity as well as
geographical conditions. This study presents a state-of-the-art method
to estimate environmental risks of pipelines by recommending
rational equations including FES, URAS, SRS, RRS, DRS, LURS
and IRS as well as FRS to calculate the risks. This study was carried
out by a relative semi-quantitative approach based on land uses and
HVAs (High-Value Areas). GIS as a tool was used to create proper
maps regarding the environmental risks, land uses and distances. The
main logic for using the formulas was the distance-based approaches
and ESI as well as intersections. Summarizing the results of the
study, a risk geographical map based on the ESIs and final risk score
(FRS) was created. The study results showed that the most sensitive
and so of high risk area would be an area comprising of mangrove
forests located in the pipeline neighborhood. Also, salty lands were
the most robust land use units in the case of pipeline failure
circumstances. Besides, using a state-of-the-art method, it showed
that mapping the risks of pipelines out with the applied method is of
more reliability and convenience as well as relative
comprehensiveness in comparison to present non-holistic methods for
assessing the environmental risks of pipelines. The focus of the
present study is “assessment" than that of “management". It is
suggested that new policies are to be implemented to reduce the
negative effects of the pipeline that has not yet been constructed
completely
Abstract: Genetic Zone Routing Protocol (GZRP) is a new
hybrid routing protocol for MANETs which is an extension of ZRP
by using Genetic Algorithm (GA). GZRP uses GA on IERP and BRP
parts of ZRP to provide a limited set of alternative routes to the
destination in order to load balance the network and robustness
during node/link failure during the route discovery process. GZRP is
studied for its performance compared to ZRP in many folds like
scalability for packet delivery and proved with improved results. This
paper presents the results of the effect of load balancing on GZRP.
The results show that GZRP outperforms ZRP while balancing the
load.
Abstract: In recent years, rehabilitation has been the subject of extensive research due to increased spending on building work and repair of built works. In all cases, it is absolutely essential to carry out methods of strengthening or repair of structural elements, and that following an inspection analysis and methodology of a correct diagnosis. The reinforced concrete columns are important elements in building structures. They support the vertical loads and provide bracing against the horizontal loads. This research about the behavior of reinforced concrete rectangular columns, rehabilitated by concrete liner, confinement FRP fabric, steel liner or cage formed by metal corners. It allows comparing the contributions of different processes used perspective section resistance elements rehabilitated compared to that is not reinforced or repaired. The different results obtained revealed a considerable gain in bearing capacity failure of reinforced sections cladding concrete, metal bracket, steel plates and a slight improvement to the section reinforced with fabric FRP. The use of FRP does not affect the weight of the structures, but the use of different techniques cladding increases the weight of elements rehabilitated and therefore the weight of the building which requires resizing foundations.
Abstract: In this work, we incorporated a quartic bond potential
into a coarse-grained bead-spring model to study lubricant adsorption
on a solid surface as well as depletion instability. The surface tension
density and the number density profiles were examined to verify the
solid-liquid and liquid-vapor interfaces during heat treatment. It was
found that both the liquid-vapor interfacial thickness and the
solid-vapor separation increase with the temperatureT* when T*is
below the phase transition temperature Tc
*. At high temperatures
(T*>Tc
*), the solid-vapor separation decreases gradually as the
temperature increases. In addition, we evaluated the lubricant weight
and bond loss profiles at different temperatures. It was observed that
the lubricant desorption is favored over decomposition and is the main
cause of the lubricant failure at the head disk interface in our
simulations.
Abstract: The goal of this research is discovering the
determinants of the success or failure of external cooperation in small
and medium enterprises (SMEs). For this, a survey was given to 190
SMEs that experienced external cooperation within the last 3 years. A
logistic regression model was used to derive organizational or strategic
characteristics that significantly influence whether external
collaboration of domestic SMEs is successful or not. Results suggest
that research and development (R&D) features in general
characteristics (both idea creation and discovering market
opportunities) that focused on and emphasized indirected-market
stakeholders (such as complementary companies and affiliates) and
strategies in innovative strategic characteristics raise the probability of
successful external cooperation. This can be used meaningfully to
build a policy or strategy for inducing successful external cooperation
or to understand the innovation of SMEs.