Abstract: E-glass-epoxy laminated composites having different fiber volume fractions (40, 50, 60 and 70) were fabricated with and without the addition of nanoclay. Flexural strength and tensile strength of the composite laminates were determined. It was observed that, with increasing the fiber volume fraction (Vf) of fiber from 40 to 60, the ability of nanoclay to enhance the tensile and flexural strength of E-glass-epoxy composites decreases significantly. At 70Vf, the tensile and flexural strength of the nanoclay reinforced E-glass-epoxy were found to be lowest when compared to the E-glass-epoxy composite made without the addition of nanoclay. Based on the obtained data and microstructure of the tested samples, plausible mechanism for the observed trends has been proposed. The enhanced mechanical properties for nanoclay reinforced E-glass-epoxy composites for 40-60 Vf, due to higher interface toughness coupled with strong interfilament bonding may have ensured the homogeneous load distribution across all the glass fibers. Results in the decrease in mechanical properties at 70Vf, may be due to the inability of the matrix to bind the nanoclay and glass-fibers.
Abstract: The discharge of dye in industrial effluents is of great concern because their presence and accumulation have a toxic or carcinogenic effect on living species. The removal of such compounds at such low levels is a difficult problem. The adsorption process is an effective and attractive proposition for the treatment of dye contaminated wastewater. Activated carbon adsorption in fixed beds is a very common technology in the treatment of water and especially in processes of decolouration. However, it is expensive and the powdered one is difficult to be separated from aquatic system when it becomes exhausted or the effluent reaches the maximum allowable discharge level. The regeneration of exhausted activated carbon by chemical and thermal procedure is also expensive and results in loss of the sorbent. The focus of this research was to evaluate the adsorption potential of the raw clay in removing rhodamine B from aqueous solutions using a laboratory fixed-bed column. The continuous sorption process was conducted in this study in order to simulate industrial conditions. The effect of process parameters, such as inlet flow rate, adsorbent bed height, and initial adsorbate concentration on the shape of breakthrough curves was investigated. A glass column with an internal diameter of 1.5 cm and height of 30 cm was used as a fixed-bed column. The pH of feed solution was set at 8.5. Experiments were carried out at different bed heights (5 - 20 cm), influent flow rates (1.6- 8 mL/min) and influent rhodamine B concentrations (20 - 80 mg/L). The obtained results showed that the adsorption capacity increases with the bed depth and the initial concentration and it decreases at higher flow rate. The column regeneration was possible for four adsorption–desorption cycles. The clay column study states the value of the excellent adsorption capacity for the removal of rhodamine B from aqueous solution. Uptake of rhodamine B through a fixed-bed column was dependent on the bed depth, influent rhodamine B concentration, and flow rate.
Abstract: The main purpose of this study is to find out, analyze and discuss basic principles of education and training in the constitutions, including the latest amendment, of France, Indonesia, Japan, South Africa, the United States of America, and Turkey. This research specifically aims at establishing a framework in order to compare educational values such as right of education, responsibilities of states and those of people, and other issues pertaining to education in the Constitution of Turkey to others. Additionally, it emphasizes the meaning of education in constitution, the reasons for references to education in constitutions and why it is important for people, states or nations and state organs. Qualitative analysis technique is performed to accomplish the aim of this study. Maximum variation sampling is used. The main data source of the analysis is official organic laws of those countries. The data is examined by using descriptive and content analysis method.
Abstract: Recent advances of Building Information Modeling (BIM) especially in the Middle East have increased remarkably. Dubai has been taking a lead on this by making it mandatory for BIM to be adopted for all projects that involve complex architecture designs. This is because BIM is a dynamic process that assists all stakeholders in monitoring the project status throughout different project phases with great transparency. It focuses on utilizing information technology to improve collaboration among project participants during the entire life cycle of the project from the initial design, to the supply chain, resource allocation, construction and all productivity requirements. In view of this trend, the paper examines the extent of applying BIM in the State of Kuwait, by exploring practitioners’ perspectives on BIM, especially their perspectives on main barriers and main advantages. To this end structured interviews were carried out based on questionnaires and with a range of different construction professionals. The results revealed that practitioners perceive improved communication and mitigated project risks by encouraged collaboration between project participants. However, it was also observed that the full implementation of BIM in the State of Kuwait requires concerted efforts to make clients demanding BIM, counteract resistance to change among construction professionals and offer more training for design team members. This paper forms part of an on-going research effort on BIM and its application in the State of Kuwait and it is on this basis that further research on the topic is proposed.
Abstract: The present work is devoted to the investigation of two series of doped bismuth molybdates: Bi26-2xMn2xMo10O69-d and
Bi26Mo10-2yMn2yO69-d. Complex oxides were synthesized by conventional solid state technology and by co-precipitation method. The products were identified by powder diffraction. The powders and ceramic samples were examined by means of densitometry, laser diffraction, and electron microscopic methods. Porosity of the ceramic materials was estimated using the hydrostatic method. The electrical conductivity measurements were carried out using impedance spectroscopy method.
Abstract: This study aims at being acquainted with the using the
body fat percentage (%BF) with body Mass Index (BMI) as input
parameters in fuzzy logic decision support system to predict properly
the lifted weight for students at weightlifting class lift according to
his abilities instead of traditional manner. The sample included 53
male students (age = 21.38 ± 0.71 yrs, height (Hgt) = 173.17 ± 5.28
cm, body weight (BW) = 70.34 ± 7.87.6 kg, Body mass index (BMI)
23.42 ± 2.06 kg.m-2, fat mass (FM) = 9.96 ± 3.15 kg and fat
percentage (% BF) = 13.98 ± 3.51 %.) experienced the weightlifting
class as a credit and has variance at BW, Hgt and BMI and FM. BMI
and % BF were taken as input parameters in FUZZY logic whereas
the output parameter was the lifted weight (LW). There were
statistical differences between LW values before and after using
fuzzy logic (Diff 3.55± 2.21, P > 0.001). The percentages of the LW
categories proposed by fuzzy logic were 3.77% of students to lift 1.0
fold of their bodies; 50.94% of students to lift 0.95 fold of their
bodies; 33.96% of students to lift 0.9 fold of their bodies; 3.77% of
students to lift 0.85 fold of their bodies and 7.55% of students to lift
0.8 fold of their bodies. The study concluded that the characteristic
changes in body composition experienced by students when
undergoing weightlifting could be utilized side by side with the
Fuzzy logic decision support system to determine the proper
workloads consistent with the abilities of students.
Abstract: The abiotic elicitation is one of the methods for
increasing the secondary metabolites production in plant tissue
cultures and it seems to be more effective than traditional strategies.
This study verified the use of silver nitrate as elicitor to enhance
flavonolignans and flavonoid taxifolin production in suspension
culture of Sylibum marianum (L.) Gaertn. Silver nitrate in various
concentrations (5.887.10-3 mol/L, 5.887.10-4 mol/L, 5.887.10-5
mol/L) was used as elicitor. The content of secondary metabolites in
cell suspension cultures was determined by high performance liquid
chromatography. The samples were taken after 6, 12, 24, 48, 72 and
168 hours of treatment. The highest content of taxifolin production
(2.2 mg.g-1) in cell suspension culture of Silybum marianum (L.)
Gaertn. was detected after silver nitrate (5.887.10-4 mol/L) treatment
and 72 h application. Flavonolignans such as silybinA, silybin B,
silydianin, silychristin, isosilybin A, isosilybin B were not produced
by cell suspension culture of S. marianum after elicitor treatment.
Our results show that the secondarymetabolites could be released
from S. marianum cells into the nutrient medium by changed
permeability of cell wall.
Abstract: During manned exploration of space, missions will require astronaut crewmembers to perform Extra Vehicular Activities (EVAs) for a variety of tasks. These EVAs take place after long periods of operations in space, and in and around unique vehicles, space structures and systems. Considering the remoteness and time spans in which these vehicles will operate, EVA system operations should utilize common worksites, tools and procedures as much as possible to increase the efficiency of training and proficiency in operations. All of the preparations need to be carried out based on studies of astronaut motions. Until now, development and training activities associated with the planned EVAs in Russian and U.S. space programs have relied almost exclusively on physical simulators. These experimental tests are expensive and time consuming. During the past few years a strong increase has been observed in the use of computer simulations due to the fast developments in computer hardware and simulation software. Based on this idea, an effort to develop a computational simulation system to model human dynamic motion for EVA is initiated. This study focuses on the simulation of an astronaut moving the orbital replaceable units into the worksites or removing them from the worksites. Our physics-based methodology helps fill the gap in quantitative analysis of astronaut EVA by providing a multisegment human arm model. Simulation work described in the study improves on the realism of previous efforts, incorporating joint stops to account for the physiological limits of range of motion. To demonstrate the utility of this approach human arm model is simulated virtually using ADAMS/LifeMOD® software. Kinematic mechanism for the astronaut’s task is studied from joint angles and torques. Simulation results obtained is validated with numerical simulation based on the principles of Newton-Euler method. Torques determined using mathematical model are compared among the subjects to know the grace and consistency of the task performed. We conclude that due to uncertain nature of exploration-class EVA, a virtual model developed using multibody dynamics approach offers significant advantages over traditional human modeling approaches.
Abstract: This study examined the extent of statistical significant difference between the economic, environmental, governance and social aspects of sustainability reporting as a result of board committee on sustainability and time (year) of reporting for business organizations in the Nigerian banking sector. The years of reporting under consideration were 2010, 2011, 2012 and 2013. Content analysis methodology was employed through a reporting index used to score the amount of economic, environmental, governance and social indicators of sustainability reporting. The results of this study indicated that business organizations with board committee on sustainability had more indicators of sustainability reporting than those without board committees on sustainability issues. Also, sustainability reporting in 2013 was higher than that of prior years (2012, 2011 and 2010) for the economic, environmental and social indicators. The governance indicators of 2012 was highest compared to the other years (2013, 2011 and 2010) under consideration in this study. The implication of this finding is that business organizations that have board committees on sustainability are monitored by such boards to report more to their stakeholders. On the other hand, business organizations are appreciating the need to engage in sustainability reporting with each passing year. This could be due to the Central Bank of Nigeria (CBN) Sustainability Reporting framework that business organizations in the banking sector have to adhere to. When sustainability issues are monitored from the board of directors, business organizations are likely to increase and improve on their sustainability reporting.
Abstract: Background: Plantar pressure measurement is an effective method for assessing plantar loading and can be applied to evaluating movement performance of the foot. The purpose of this study is to explore the sprint athletes’ plantar loading characteristics and pain profiles in static standing. Methods: Experiments were undertaken on 80 first-division college sprint athletes and 85 healthy non-sprinters. ‘JC Mat’, the optical plantar pressure measurement was applied to examining the differences between both groups in the arch index (AI), three regional and six distinct sub-regional plantar pressure distributions (PPD), and footprint characteristics. Pain assessment and self-reported health status in sprint athletes were examined for evaluating their common pain areas. Results: Findings from the control group, the males’ AI fell into the normal range. Yet, the females’ AI was classified as the high-arch type. AI values of the sprint group were found to be significantly lower than the control group. PPD were higher at the medial metatarsal bone of both feet and the lateral heel of the right foot in the sprint group, the males in particular, whereas lower at the medial and lateral longitudinal arches of both feet. Footprint characteristics tended to support the results of the AI and PPD, and this reflected the corresponding pressure profiles. For the sprint athletes, the lateral knee joint and biceps femoris were the most common musculoskeletal pains. Conclusions: The sprint athletes’ AI were generally classified as high arches, and that their PPD were categorized between the features of runners and high-arched runners. These findings also correspond to the profiles of patellofemoral pain syndrome (PFPS)-related plantar pressure. The pain profiles appeared to correspond to the symptoms of high-arched runners and PFPS. The findings reflected upon the possible link between high arches and PFPS. The correlation between high-arched runners and PFPS development is worth further studies.
Abstract: Urbanization, population growth, climate change and the current increase in water demand have made the adoption of innovative demand management strategies crucial to the water industry. Water conservation in urban areas has to be improved by encouraging consumers to adopt more sustainable habits and behaviours. This includes informing and educating them about their households’ water consumption and advising them about ways to achieve significant savings on a daily basis. This paper presents a study conducted in the context of the European FP7 WISDOM Project. By integrating innovative Information and Communication Technologies (ICT) frameworks, this project aims at achieving a change in water savings. More specifically, behavioural change will be attempted by implementing smart meters and in-home displays in a trial group of selected households within Cardiff (UK). Using this device, consumers will be able to receive feedback and information about their consumption but will also have the opportunity to compare their consumption to the consumption of other consumers and similar households. Following an initial survey, it appeared necessary to implement these in-home displays in a way that matches consumer's motivations to save water. The results demonstrated the importance of various factors influencing people’s daily water consumption. Both the relevant literature on the subject and the results of our survey therefore led us to include within the in-home device a variety of elements. It first appeared crucial to make consumers aware of the economic aspect of water conservation and especially of the significant financial savings that can be achieved by reducing their household’s water consumption on the long term. Likewise, reminding participants of the impact of their consumption on the environment by making them more aware of water scarcity issues around the world will help increasing their motivation to save water. Additionally, peer pressure and social comparisons with neighbours and other consumers, accentuated by the use of online social networks such as Facebook or Twitter, will likely encourage consumers to reduce their consumption. Participants will also be able to compare their current consumption to their past consumption and to observe the consequences of their efforts to save water through diverse graphs and charts. Finally, including a virtual water game within the display will help the whole household, children and adults, to achieve significant reductions by providing them with simple tips and advice to save water on a daily basis. Moreover, by setting daily and weekly goals for them to reach, the game will expectantly generate cooperation between family members. Members of each household will indeed be encouraged to work together to reduce their water consumption within different rooms of the house, such as the bathroom, the kitchen, or the toilets. Overall, this study will allow us to understand the elements that attract consumers the most and the features that are most commonly used by the participants. In this way, we intend to determine the main factors influencing water consumption in order to identify the measures that will most encourage water conservation in both the long and short term.
Abstract: Municipal Solid Waste (MSW) disposed in landfill sites decompose under anaerobic conditions and produce gases which mainly contain carbon dioxide (CO2) and methane (CH4). Methane has the potential of causing global warming 25 times more than CO2, and can potentially affect human life and environment. Thus, this research aims to determine MSW generation and the annual CH4 emissions from the generated waste in Oman over the years 1971-2030. The estimation of total waste generation was performed using existing models, while the CH4 emissions estimation was performed using the intergovernmental panel on climate change (IPCC) default method. It is found that total MSW generation in Oman might be reached 3,089 Gg in the year 2030, which approximately produced 85 Gg of CH4 emissions in the year 2030.
Abstract: By GEO5 FEM program with four rockfill slope
modeling and stability analysis was performed for S1, S2, S3 and
S4 slopes where landslides of the shalefills were limited. Effective
angle of internal friction (φ'°) 17°-22.5°, the effective cohesion (c')
from 0.5 to 1.8 kPa, saturated unit weight 1.78-2.43 g/cm3, natural
unit weight 1.9-2.35 g/cm3, dry unit weight 1.97-2.40 g/cm3, the
permeability coefficient of 1x10-4 - 6.5x10-4 cm/s. In cross-sections
of the slope, GEO 5 FEM program possible critical surface tension
was examined. Rockfill dump design was made to prevent sliding
slopes. Bulk material designated geotechnical properties using also
GEO5 programs FEM and stability program via a safety factor
determined and calculated according to the values S3 and S4 No.
slopes are stable S1 and S2 No. slopes were close to stable state
that has been found to be risk. GEO5 programs with limestone rock
fill dump through FEM program was found to exhibit stability.
Abstract: We assume an IoT-based smart-home environment where the on-off status of each of the electrical appliances including the room lights can be recognized in a real time by monitoring and analyzing the smart meter data. At any moment in such an environment, we can recognize what the household or the user is doing by referring to the status data of the appliances. In this paper, we focus on a smart-home service that is to activate a robot vacuum cleaner at right time by recognizing the user situation, which requires a situation-aware model that can distinguish the situations that allow vacuum cleaning (Yes) from those that do not (No). We learn as our candidate models a few classifiers such as naïve Bayes, decision tree, and logistic regression that can map the appliance-status data into Yes and No situations. Our training and test data are obtained from simulations of user behaviors, in which a sequence of user situations such as cooking, eating, dish washing, and so on is generated with the status of the relevant appliances changed in accordance with the situation changes. During the simulation, both the situation transition and the resulting appliance status are determined stochastically. To compare the performances of the aforementioned classifiers we obtain their learning curves for different types of users through simulations. The result of our empirical study reveals that naïve Bayes achieves a slightly better classification accuracy than the other compared classifiers.
Abstract: In this paper, we present a novel 2.5D face recognition method based on Gabor Discrete Cosine Transform (GDCT). In the proposed method, the Gabor filter is applied to extract feature vectors from the texture and the depth information. Then, Discrete Cosine Transform (DCT) is used for dimensionality and redundancy reduction to improve computational efficiency. The system is combined texture and depth information in the decision level, which presents higher performance compared to methods, which use texture and depth information, separately. The proposed algorithm is examined on publically available Bosphorus database including models with pose variation. The experimental results show that the proposed method has a higher performance compared to the benchmark.
Abstract: In many practical situations, bubbles are dispersed in a
liquid phase. Understanding these complex bubbly flows is therefore
a key issue for applications such as shell and tube heat exchangers,
mineral flotation and oxidation in water treatment. Although a large
body of work exists for bubbles rising in an unbounded medium,
that of bubbles rising in constricted geometries has received less
attention. The particular case of a bubble sliding underneath an
inclined surface is common to two-phase flow systems. The current
study intends to expand this knowledge by performing experiments
to quantify the streamwise flow structures associated with a single
sliding air bubble under an inclined surface in quiescent water. This
is achieved by means of two-dimensional, two-component particle
image velocimetry (PIV), performed with a continuous wave laser
and high-speed camera. PIV vorticity fields obtained in a plane
perpendicular to the sliding surface show that there is significant bulk
fluid motion away from the surface. The associated momentum of the
bubble means that this wake motion persists for a significant time
before viscous dissipation. The magnitude and direction of the flow
structures in the streamwise measurement plane are found to depend
on the point on its path through which the bubble enters the plane.
This entry point, represented by a phase angle, affects the nature and
strength of the vortical structures. This study reconstructs the vorticity
field in the wake of the bubble, converting the field at different
instances in time to slices of a large-scale wake structure. This is, in
essence, Taylor’s ”frozen turbulence” hypothesis. Applying this to the
vorticity fields provides a pseudo three-dimensional representation
from 2-D data, allowing for a more intuitive understanding of the
bubble wake. This study provides insights into the complex dynamics
of a situation common to many engineering applications, particularly
shell and tube heat exchangers in the nucleate boiling regime.
Abstract: Water is a very rare natural resource in South Africa. Ga-Selati River is used for both domestic and industrial purposes. This study was carried out in order to assess the quality of Ga-Selati River in a mining area of Limpopo Province-Phalaborwa. The pH, Electrical Conductivity (EC) and Total Dissolved Solids (TDS) were determined using a Crinson multimeter while turbidity was measured using a Labcon Turbidimeter. The concentrations of Al, Ca, Cd, Cr, Fe, K, Mg, Mn, Na and Pb were analysed in triplicate using a Varian 520 flame atomic absorption spectrometer (AAS) supplied by PerkinElmer, after acid digestion with nitric acid in a fume cupboard. The average pH of the river from eight different sampling sites was 8.00 and 9.38 in wet and dry season respectively. Higher EC values were determined in the dry season (138.7 mS/m) than in the wet season (96.93 mS/m). Similarly, TDS values were higher in dry (929.29 mg/L) than in the wet season (640.72 mg/L) season. These values exceeded the recommended guideline of South Africa Department of Water Affairs and Forestry (DWAF) for domestic water use (70 mS/m) and that of the World Health Organization (WHO) (600 mS/m), respectively. Turbidity varied between 1.78-5.20 and 0.95-2.37 NTU in both wet and dry seasons. Total hardness of 312.50 mg/L and 297.75 mg/L as the concentration of CaCO3 was computed for the river in both the wet and the dry seasons and the river water was categorised as very hard. Mean concentration of the metals studied in both the wet and the dry seasons are: Na (94.06 mg/L and 196.3 mg/L), K (11.79 mg/L and 13.62 mg/L), Ca (45.60 mg/L and 41.30 mg/L), Mg (48.41 mg/L and 44.71 mg/L), Al (0.31 mg/L and 0.38 mg/L), Cd (0.01 mg/L and 0.01 mg/L), Cr (0.02 mg/L and 0.09 mg/L), Pb (0.05 mg/L and 0.06 mg/L), Mn (0.31 mg/L and 0.11 mg/L) and Fe (0.76 mg/L and 0.69 mg/L). Results from this study reveal that most of the metals were present in concentrations higher than the recommended guidelines of DWAF and WHO for domestic use and the protection of aquatic life.
Abstract: This paper compares the findings of two studies conducted to determine the effectiveness of simulation-based, hands-on and feedback mechanism on students learning by answering the following questions: 1). Does the use of simulation improve students’ learning outcomes? 2). How do students perceive the instructional design features embedded in the simulation program such as exploration and scaffolding support in learning new concepts? 3.) What is the effect of feedback mechanisms on students’ learning in the use of simulation-based labs? The paper also discusses the other aspects of findings which reveal that simulation by itself is not very effective in promoting student learning. Simulation becomes effective when it is followed by hands-on activity and feedback mechanisms. Furthermore, the paper presents recommendations for improving student learning through the use of simulation-based, hands-on, and feedback-based teaching methodologies.
Abstract: MSN used to be the most popular application for
communicating among social networks, but Facebook chat is now the
most popular. Facebook and MSN have similar characteristics,
including usefulness, ease-of-use, and a similar function, which is the
exchanging of information with friends. Facebook outperforms MSN
in both of these areas. However, the adoption of Facebook and
abandonment of MSN have occurred for other reasons. Functions can
be improved, but users’ willingness to use does not just depend on
functionality. Flow status has been established to be crucial to users’
adoption of cyber applications and to affects users’ adoption of
software applications. If users experience flow in using software
application, they will enjoy using it frequently, and even change their
preferred application from an old to this new one. However, no
investigation has examined choice behavior related to switching from
Facebook to MSN based on a consideration of flow experiences and
functions. This investigation discusses the flow experiences and
functions of social-networking applications. Flow experience is found
to affect perceived ease of use and perceived usefulness; perceived
ease of use influences information ex-change with friends, and
perceived usefulness; information exchange influences perceived
usefulness, but information exchange has no effect on flow
experience.
Abstract: To increase the temperature contrast in thermal
images, the characteristics of the electrical conductivity and thermal
imaging modalities can be combined. In this experimental study, it is
objected to observe whether the temperature contrast created by the
tumor tissue can be improved just due to the current application
within medical safety limits. Various thermal breast phantoms are
developed to simulate the female breast tissue. In vitro experiments
are implemented using a thermal infrared camera in a controlled
manner. Since experiments are implemented in vitro, there is no
metabolic heat generation and blood perfusion. Only the effects and
results of the electrical stimulation are investigated. Experimental
study is implemented with two-dimensional models. Temperature
contrasts due to the tumor tissues are obtained. Cancerous tissue is
determined using the difference and ratio of healthy and tumor
images. 1 cm diameter single tumor tissue causes almost 40 °mC
temperature contrast on the thermal-breast phantom. Electrode
artifacts are reduced by taking the difference and ratio of background
(healthy) and tumor images. Ratio of healthy and tumor images show
that temperature contrast is increased by the current application.