Abstract: In this paper, the application of thermal spray
coatings in high speed shafts by a revolution up to 23000 RPM
has been studied. Gas compressor shafts are worn in contact
zone with journal therefore will be undersized. Wear
mechanisms of compressor shaft were identified. The
predominant wear mechanism is abrasion wear. The worn
surface was coated by hard WC-Co cermets using high
velocity oxy fuel (HVOF) after preparation. The shafts were in
satisfactory service in 8000h period. The metallurgical and
Tribological studies has been made on the worn and coated
shaft using optical microscopy, scanning electron microscopy
(SEM) and X-ray diffraction.
Abstract: This paper presents an economic game for sybil
detection in a distributed computing environment. Cost parameters
reflecting impacts of different sybil attacks are introduced in the sybil
detection game. The optimal strategies for this game in which both
sybil and non-sybil identities are expected to participate are devised.
A cost sharing economic mechanism called Discriminatory
Rewarding Mechanism for Sybil Detection is proposed based on this
game. A detective accepts a security deposit from each active agent,
negotiates with the agents and offers rewards to the sybils if the latter
disclose their identity. The basic objective of the detective is to
determine the optimum reward amount for each sybil which will
encourage the maximum possible number of sybils to reveal
themselves. Maintaining privacy is an important issue for the
mechanism since the participants involved in the negotiation are
generally reluctant to share their private information. The mechanism
has been applied to Tor by introducing a reputation scoring function.
Abstract: There is inadequate information on the practice of
female genital mutilation (FGM) in the UK, and there are often
myths and perceptions within communities that influence the
effectiveness of prevention programmes. This means it is difficult to
address the trends and changes in the practice in the UK.
To this end, FORWARD undertook novel and innovative research
using the Participatory Ethnographic and Evaluative Research
(PEER) method to explore the views of women from Eritrea, Sudan,
Somalia and Ethiopia that live in London and Bristol (two UK cities).
Women-s views, taken from PEER interviews, reflected reasons for
continued practice of FGM: marriageability, the harnessing and
control of female sexuality, and upholding traditions from their
countries of origin. It was also clear that the main supporters of the
practice were believed to be older women within families and
communities.
Women described the impact FGM was having on their lives as
isolating. And although it was clearly considered a private and
personal matter, they developed a real sense of connection with their
peers within the research process.
The women were overwhelmingly positive about combating the
practice, although they believed it would probably take a while
before it ends completely. They also made concrete
recommendations on how to improve support services for women
affected by FGM: Training for professionals (particularly in
healthcare), increased engagement with, and outreach to,
communities, culturally appropriate materials and information made
available and accessible to communities, and more consequent
implementation of legislation.
Finally, the women asked for more empathy and understanding,
particularly from health professionals. Rather than presenting FGM
as a completely alien and inconceivable practice, it may help for
those looking into these women-s lives and working with them to
understand the social and economic context in which the practice
takes place.
Abstract: In this paper, an automatic determination algorithm for nuclear magnetic resonance (NMR) spectra of the metabolites in the living body by magnetic resonance spectroscopy (MRS) without human intervention or complicated calculations is presented. In such method, the problem of NMR spectrum determination is transformed into the determination of the parameters of a mathematical model of the NMR signal. To calculate these parameters efficiently, a new model called modified Hopfield neural network is designed. The main achievement of this paper over the work in literature [30] is that the speed of the modified Hopfield neural network is accelerated. This is done by applying cross correlation in the frequency domain between the input values and the input weights. The modified Hopfield neural network can accomplish complex dignals perfectly with out any additinal computation steps. This is a valuable advantage as NMR signals are complex-valued. In addition, a technique called “modified sequential extension of section (MSES)" that takes into account the damping rate of the NMR signal is developed to be faster than that presented in [30]. Simulation results show that the calculation precision of the spectrum improves when MSES is used along with the neural network. Furthermore, MSES is found to reduce the local minimum problem in Hopfield neural networks. Moreover, the performance of the proposed method is evaluated and there is no effect on the performance of calculations when using the modified Hopfield neural networks.
Abstract: Stable bacterial polymorphism on a single limiting resource may appear if between the evolved strains metabolic interactions take place that allow the exchange of essential nutrients [8]. Towards an attempt to predict the possible outcome of longrunning evolution experiments, a network based on the metabolic capabilities of homogeneous populations of every single gene knockout strain (nodes) of the bacterium E. coli is reconstructed. Potential metabolic interactions (edges) are allowed only between strains of different metabolic capabilities. Bacterial communities are determined by finding cliques in this network. Growth of the emerged hypothetical bacterial communities is simulated by extending the metabolic flux balance analysis model of Varma et al [2] to embody heterogeneous cell population growth in a mutual environment. Results from aerobic growth on 10 different carbon sources are presented. The upper bounds of the diversity that can emerge from single-cloned populations of E. coli such as the number of strains that appears to metabolically differ from most strains (highly connected nodes), the maximum clique size as well as the number of all the possible communities are determined. Certain single gene deletions are identified to consistently participate in our hypothetical bacterial communities under most environmental conditions implying a pattern of growth-condition- invariant strains with similar metabolic effects. Moreover, evaluation of all the hypothetical bacterial communities under growth on pyruvate reveals heterogeneous populations that can exhibit superior growth performance when compared to the performance of the homogeneous wild-type population.
Abstract: Pressure waves and Water Hammer occur in a
pumping system when valves are closed or opened suddenly or in
the case of sudden failure of pumps. Determination of maximum
water hammer is considered one of the most important technical
and economical items of which engineers and designers of
pumping stations and conveyance pipelines should take care.
Hammer Software is a recent application used to simulate water
hammer. The present study focuses on determining significance of
each input parameter of the application relative to the maximum
amount of water hammer estimated by the software. The study
determines estimated maximum water hammer variations due to
variations of input parameters including water temperature, pipe
type, thickness and diameter, electromotor rpm and power, and
moment of inertia of electromotor and pump. In our study,
Kuhrang Pumping Station was modeled using WaterGEMS
Software. The pumping station is characterized by total discharge
of 200 liters per second, dynamic height of 194 meters and 1.5
kilometers of steel conveyance pipeline and transports water to
Cheshme Morvarid for farmland irrigation. The model was run in
steady hydraulic condition and transferred to Hammer Software.
Then, the model was run in several unsteady hydraulic conditions
and sensitivity of maximum water hammer to each input parameter
was calculated. It is shown that parameters to which maximum
water hammer is most sensitive are moment of inertia of pump and
electromotor, diameter, type and thickness of pipe and water
temperature, respectively.
Abstract: In Croatia, the majority of cultured marine fish species are reared in net cages. The intensive production of the fish in net cages may generate the considerable amount of bio waste and change water quality especially in enclosed and semi-enclosed coastal areas. The aim of this paper is to assess the potential impact of sea bass (Dicentrarchus labrax L.) cage farm on water quality. The weak relationship between food supply and water quality parameters (nutrient content and phytoplankton biomass) was found, but significant changes in oxygen saturation was observed in the cages during the warmer period of a year especially in the morning (occasionally it dropped below 70 %). Despite of, satisfactory results of water quality parameters, it is necessary to establish comprehensive monitoring process, especially to include quality assessment of fouling communities.
Abstract: This paper describes the design concepts and
implementation of a 5-Joint mechanical arm for a rescue robot named
CEO Mission II. The multi-joint arm is a five degree of freedom
mechanical arm with a four bar linkage, which can be stretched to
125 cm. long. It is controlled by a teleoperator via the user-friendly
control and monitoring GUI program. With Inverse Kinematics
principle, we developed the method to control the servo angles of all
arm joints to get the desired tip position. By clicking the determined
tip position or dragging the tip of the mechanical arm on the
computer screen to the desired target point, the robot will compute
and move its multi-joint arm to the pose as seen on the GUI screen.
The angles of each joint are calculated and sent to all joint servos
simultaneously in order to move the mechanical arm to the desired
pose at once. The operator can also use a joystick to control the
movement of this mechanical arm and the locomotion of the robot.
Many sensors are installed at the tip of this mechanical arm for
surveillance from the high level and getting the vital signs of victims
easier and faster in the urban search and rescue tasks. It works very
effectively and easy to control. This mechanical arm and its software
were developed as a part of the CEO Mission II Rescue Robot that
won the First Runner Up award and the Best Technique award from
the Thailand Rescue Robot Championship 2006. It is a low cost,
simple, but functioning 5-Jiont mechanical arm which is built from
scratch, and controlled via wireless LAN 802.11b/g. This 5-Jiont
mechanical arm hardware concept and its software can also be used
as the basic mechatronics to many real applications.
Abstract: Virtual touch screen using camera is an ordinary screen which uses a camera to imitate the touch screen by taking a picture of an indicator, e.g., finger, which is laid on the screen, converting the indicator tip position on the picture to the position on the screen, and moving the cursor on the screen to that position. In fact, the indicator is not laid on the screen directly, but it is intervened by the cover at some intervals. In spite of this gap, if the eye-indicator-camera angle is not large, the mapping from the indicator tip positions on the image to the corresponding cursor positions on the screen is not difficult and could be done with a little error. However, the larger the angle is, the bigger the error in the mapping occurs. This paper proposes cursor position estimation model for virtual touch screen using camera which could eliminate this kind of error. The proposed model (i) moves the on-screen pilot cursor to the screen position which locates on the screen at the position just behind the indicator tip when the indicator tip has been looked from the camera position, and then (ii) converts that pilot cursor position to the desirable cursor position (the position on the screen when it has been looked from the user-s eye through the indicator tip) by using the bilinear transformation. Simulation results show the correctness of the estimated cursor position by using the proposed model.
Abstract: This paper presents an analysis on the capacity and performance of MIMO-OFDM systems. The work is focused on the capacity of MIMO-OFDM systems over rician fading channel, in the case of the channel being known at the receiver only, which is more practical case of the channel. Simple expression for capacity is derived for the case of correlated rician fading. The performance of some MIMO-OFDM implementations with rician fading model is presented using an Alamouti coding scheme and Simulation results are obtained for both capacity and performance analysis.
Abstract: We discuss the signal detection through nonlinear
threshold systems. The detection performance is assessed by the
probability of error Per . We establish that: (1) when the signal is
complete suprathreshold, noise always degrades the signal detection
both in the single threshold system and in the parallel array of
threshold devices. (2) When the signal is a little subthreshold, noise
degrades signal detection in the single threshold system. But in the
parallel array, noise can improve signal detection, i.e., stochastic
resonance (SR) exists in the array. (3) When the signal is predominant
subthreshold, noise always can improve signal detection and SR
always exists not only in the single threshold system but also in the
parallel array. (4) Array can improve signal detection by raising the
number of threshold devices. These results extend further the
applicability of SR in signal detection.
Abstract: this paper presents a novel scheme which is capable of reducing the error rate and improves the transmission performance in the asynchronous cooperative MIMO systems. A case study of image transmission is applied to prove the efficient of scheme. The linear dispersion structure is employed to accommodate the cooperative wireless communication network in the dynamic topology of structure, as well as to achieve higher throughput than conventional space–time codes based on orthogonal designs. The LDPC encoder without girth-4 and the STBC encoder with guard intervals are respectively introduced. The experiment results show that the combined coder of LDPC-STBC with guard intervals can be the good error correcting coders and BER performance in the asynchronous cooperative communication. In the case study of image transmission, the results show that in the transmission process, the image quality which is obtained by applied combined scheme is much better than it which is not applied the scheme in the asynchronous cooperative MIMO systems.
Abstract: WiMAX is defined as Worldwide Interoperability for
Microwave Access by the WiMAX Forum, formed in June 2001 to
promote conformance and interoperability of the IEEE 802.16
standard, officially known as WirelessMAN. The attractive features
of WiMAX technology are very high throughput and Broadband
Wireless Access over a long distance. A detailed simulation
environment is demonstrated with the UGS, nrtPS and ertPS service
classes for throughput, delay and packet delivery ratio for a mixed
environment of fixed and mobile WiMAX. A simple mobility aspect
is considered for the mobile WiMAX and the PMP mode of
transmission is considered in TDD mode. The Network Simulator 2
(NS-2) is the tool which is used to simulate the WiMAX network
scenario. A simple Priority Scheduler and Weighted Round Robin
Schedulers are the WiMAX schedulers used in the research work
Abstract: The aim of this study is to develop mathematical
relationships for the performance parameter brake thermal efficiency
(BTE) and emission parameter nitrogen oxides (NOx) for the various
esters of vegetable oils used as CI engine fuel. The BTE is an
important performance parameter defining the ability of engine to
utilize the energy supplied and power developed similarly it is
indication of efficiency of fuels used. The esters of cottonseed oil,
soybean oil, jatropha oil and hingan oil are prepared using
transesterification process and characterized for their physical and
main fuel properties including viscosity, density, flash point and
higher heating value using standard test methods. These esters are
tried as CI engine fuel to analyze the performance and emission
parameters in comparison to diesel. The results of the study indicate
that esters as a fuel does not differ greatly with that of diesel in
properties. The CI engine performance with esters as fuel is in line
with the diesel where as the emission parameters are reduced with the
use of esters.
The correlation developed between BTE and brake power(BP),
gross calorific value(CV), air-fuel ratio(A/F), heat carried away by
cooling water(HCW). Another equation is developed between the
NOx emission and CO, HC, smoke density (SD), exhaust gas
temperature (EGT). The equations are verified by comparing the
observed and calculated values which gives the coefficient of
correlation of 0.99 and 0.96 for the BTE and NOx equations
respectively.
Abstract: In this paper a novel, simple and reliable digital firing
scheme has been implemented for speed control of three-phase
induction motor using ac voltage controller. The system consists of
three-phase supply connected to the three-phase induction motor via
three triacs and its control circuit. The ac voltage controller has three
modes of operation depending on the shape of supply current. The
performance of the induction motor differs in each mode where the
speed is directly proportional with firing angle in two modes and
inversely in the third one. So, the control system has to detect the
current mode of operation to choose the correct firing angle of triacs.
Three sensors are used to feed the line currents to control system to
detect the mode of operation. The control strategy is implemented
using a low cost Xilinx Spartan-3E field programmable gate array
(FPGA) device. Three PI-controllers are designed on FPGA to
control the system in the three-modes. Simulation of the system is
carried out using PSIM computer program. The simulation results
show stable operation for different loading conditions especially in
mode 2/3. The simulation results have been compared with the
experimental results from laboratory prototype.
Abstract: In this paper, we develop quartic nonpolynomial
spline method for the numerical solution of third order two point
boundary value problems. It is shown that the new method gives
approximations, which are better than those produced by other spline
methods. Convergence analysis of the method is discussed through
standard procedures. Two numerical examples are given to illustrate
the applicability and efficiency of the novel method.
Abstract: E-Learning systems are used by many learners and
teachers. The developer is developing the e-Learning system. However,
the developer cannot do system construction to satisfy all of
users- demands. We discuss a method of constructing e-Learning
systems where learners and teachers can design, try to use, and share
extending system functions that they want to use; which may be nally
added to the system by system managers.
Abstract: In this work we study the effect of several covariates X on a censored response variable T with unknown probability distribution. In this context, most of the studies in the literature can be located in two possible general classes of regression models: models that study the effect the covariates have on the hazard function; and models that study the effect the covariates have on the censored response variable. Proposals in this paper are in the second class of models and, more specifically, on least squares based model approach. Thus, using the bootstrap estimate of the bias, we try to improve the estimation of the regression parameters by reducing their bias, for small sample sizes. Simulation results presented in the paper show that, for reasonable sample sizes and censoring levels, the bias is always smaller for the new proposals.
Abstract: As the mobile Internet has become widespread in
recent years, communication based on mobile networks is increasing.
As a result, security threats have been posed with regard to the
abnormal traffic of mobile networks, but mobile security has been
handled with focus on threats posed by mobile malicious codes, and
researches on security threats to the mobile network itself have not
attracted much attention. In mobile networks, the IP address of the data
packet is a very important factor for billing purposes. If one mobile
terminal use an incorrect IP address that either does not exist or could
be assigned to another mobile terminal, billing policy will cause
problems. We monitor and analyze 3G mobile data networks traffics
for a period of time and finds some abnormal IP packets. In this paper,
we analyze the reason for abnormal IP packets on 3G Mobile Data
Networks. And we also propose an algorithm based on IP address table
that contains addresses currently in use within the mobile data network
to detect abnormal IP packets.
Abstract: As a vital activity for companies, new product
development (NPD) is also a very risky process due to the high
uncertainty degree encountered at every development stage and the
inevitable dependence on how previous steps are successfully
accomplished. Hence, there is an apparent need to evaluate new
product initiatives systematically and make accurate decisions under
uncertainty. Another major concern is the time pressure to launch a
significant number of new products to preserve and increase the
competitive power of the company. In this work, we propose an
integrated decision-making framework based on neural networks and
fuzzy logic to make appropriate decisions and accelerate the
evaluation process. We are especially interested in the two initial
stages where new product ideas are selected (go/no go decision) and
the implementation order of the corresponding projects are
determined. We show that this two-staged intelligent approach allows
practitioners to roughly and quickly separate good and bad product
ideas by making use of previous experiences, and then, analyze a
more shortened list rigorously.