Abstract: Palladium-catalyzed hydrodechlorination is a
promising alternative for the treatment of environmentally relevant
water bodies, such as groundwater, contaminated with chlorinated
organic compounds (COCs). In the aqueous phase
hydrodechlorination of COCs, Pd-based catalysts were found to have
a very high catalytic activity. However, the full utilization of the
catalyst-s potential is impeded by the sensitivity of the catalyst to
poisoning and deactivation induced by reduced sulfur compounds
(e.g. sulfides). Several regenerants have been tested before to recover
the performance of sulfide-fouled Pd catalyst. But these only
delivered partial success with respect to re-establishment of the
catalyst activity. In this study, the deactivation behaviour of
Pd/Al2O3 in the presence of sulfide was investigated. Subsequent to
total deactivation the catalyst was regenerated in the aqueous phase
using potassium permanganate. Under neutral pH condition,
oxidative regeneration with permanganate delivered a slow recovery
of catalyst activity. However, changing the pH of the bulk solution to
acidic resulted in the complete recovery of catalyst activity within a
regeneration time of about half an hour. These findings suggest the
superiority of permanganate as regenerant in re-activating Pd/Al2O3
by oxidizing Pd-bound sulfide.
Abstract: The purpose of this paper isunavailability of the two main types of conveSwedish traction power supply (TPS) system, i.e.static converter. The number of outages and the ouused to analyze and compare the unavailability oconverters. The mean cumulative function (MCF)analyze the number of outages and the unavailabthe forced outage rate (FOR) concept has been uoutage rates. The study shows that the outagesfailure occur at a constant rate by calendar timconverter stations, while very few stations havedecreasing rate. It has also been found that the stata higher number of outages and a higher outage ratcompared to the rotary converter types. The resultsthat combining the number of outages and the fgives a better view of the converters performasupport for the maintenance decision. In fact, usingdoes not reflect reality. Comparing these two indein identifying the areas where extra resources are maintenance planning and where improvementsoutage in the TPS system.KeywordsFrequency Converter, Forced OuCumulative Function, Traction Power Supply, ESystems.
Abstract: We present a new method for the fully automatic 3D
reconstruction of the coronary artery centerlines, using two X-ray
angiogram projection images from a single rotating monoplane
acquisition system. During the first stage, the input images are
smoothed using curve evolution techniques. Next, a simple yet
efficient multiscale method, based on the information of the Hessian
matrix, for the enhancement of the vascular structure is introduced.
Hysteresis thresholding using different image quantiles, is used to
threshold the arteries. This stage is followed by a thinning procedure
to extract the centerlines. The resulting skeleton image is then pruned
using morphological and pattern recognition techniques to remove
non-vessel like structures. Finally, edge-based stereo correspondence
is solved using a parallel evolutionary optimization method based on
f symbiosis. The detected 2D centerlines combined with disparity
map information allow the reconstruction of the 3D vessel
centerlines. The proposed method has been evaluated on patient data
sets for evaluation purposes.
Abstract: The quest for alternatefuels for a CI engine has
become all the more imperative considering its importance in the
economy of a nation and from the standpoint of preserving the environment. Reported in this paper are the combustion performance and P-θ characteristics of a CI engine operating on B20 biodiesel fuel derived from Jatropha oil.Itis observed that the twin effect of advancing the injection timing and increasing the injector opening pressure (IOP) up to 220 barhas resulted in minimum brake specific
energy consumption and higherpeak pressure. It is also observed that
the crank angle of occurrence of peak pressure progressestowards top
dead center (TDC) as the timing is advanced and IOP is increased.
Abstract: In this study, an ablation, mechanical and thermal properties of a rocket motor insulation from phenolic/ fiber matrix composites forming a laminate with different fiber between fiberglass and locally available synthetic fibers. The phenolic/ fiber matrix composites was mechanics and thermal properties by means of tensile strength, ablation, TGA and DSC. The design of thermal insulation involves several factors.Determined the mechanical properties according to MIL-I-24768: Density >1.3 g/cm3, Tensile strength >103 MPa and Ablation
Abstract: It is necessary to evaluate the bridges conditions and
strengthen bridges or parts of them. The reinforcement necessary due
to some reasons can be summarized as: First, a changing in use of
bridge could produce internal forces in a part of structural which
exceed the existing cross-sectional capacity. Second, bridges may
also need reinforcement because damage due to external factors
which reduced the cross-sectional resistance to external loads. One of
other factors could listed here its misdesign in some details, like
safety of bridge or part of its.This article identify the design demands
of Qing Shan bridge located in is in Heilongjiang Province He gang -
Nen Jiang Road 303 provincial highway, Wudalianchi area, China, is
an important bridge in the urban areas. The investigation program
was include the observation and evaluate the damage in T- section
concrete beams , prestressed concrete box girder bridges section in
additional evaluate the whole state of bridge includes the pier ,
abutments , bridge decks, wings , bearing and capping beam, joints,
........etc. The test results show that the bridges in general structural
condition are good. T beam span No 10 were observed, crack
extended upward along the ribbed T beam, and continue to the T
beam flange. Crack width varying between 0.1mm to 0.4mm, the
maximum about 0.4mm. The bridge needs to be improved flexural
bending strength especially at for T beam section.
Abstract: The last decade has shown that object-oriented
concept by itself is not that powerful to cope with the rapidly
changing requirements of ongoing applications. Component-based
systems achieve flexibility by clearly separating the stable parts of
systems (i.e. the components) from the specification of their
composition. In order to realize the reuse of components effectively
in CBSD, it is required to measure the reusability of components.
However, due to the black-box nature of components where the
source code of these components are not available, it is difficult to
use conventional metrics in Component-based Development as these
metrics require analysis of source codes. In this paper, we survey
few existing component-based reusability metrics. These metrics
give a border view of component-s understandability, adaptability,
and portability. It also describes the analysis, in terms of quality
factors related to reusability, contained in an approach that aids
significantly in assessing existing components for reusability.
Abstract: The principle of frequency and amplitude measurement of a vibrating object in water using ultrasonic speckle technique is presented in this paper. Compared with other traditional techniques, the ultrasonic speckle technique can be applied to vibration measurement of a nonmetal object with rough surface in water in a noncontact way. The relationship between speckle movement and object movement was analyzed. Based on this study, an ultrasonic speckle measurement system was set up. With this system the frequency and amplitude of an underwater vibrating cantilever beam was detected. The result shows that the experimental data is in good agreement with the calibrating data.
Abstract: In this paper, to optimize the “Characteristic Straight Line Method" which is used in the soil displacement analysis, a “best estimate" of the geodetic leveling observations has been achieved by taking in account the concept of 'Height systems'. This concept has been discussed in detail and consequently the concept of “height". In landslides dynamic analysis, the soil is considered as a mosaic of rigid blocks. The soil displacement has been monitored and analyzed by using the “Characteristic Straight Line Method". Its characteristic components have been defined constructed from a “best estimate" of the topometric observations. In the measurement of elevation differences, we have used the most modern leveling equipment available. Observational procedures have also been designed to provide the most effective method to acquire data. In addition systematic errors which cannot be sufficiently controlled by instrumentation or observational techniques are minimized by applying appropriate corrections to the observed data: the level collimation correction minimizes the error caused by nonhorizontality of the leveling instrument's line of sight for unequal sight lengths, the refraction correction is modeled to minimize the refraction error caused by temperature (density) variation of air strata, the rod temperature correction accounts for variation in the length of the leveling rod' s Invar/LO-VAR® strip which results from temperature changes, the rod scale correction ensures a uniform scale which conforms to the international length standard and the introduction of the concept of the 'Height systems' where all types of height (orthometric, dynamic, normal, gravity correction, and equipotential surface) have been investigated. The “Characteristic Straight Line Method" is slightly more convenient than the “Characteristic Circle Method". It permits to evaluate a displacement of very small magnitude even when the displacement is of an infinitesimal quantity. The inclination of the landslide is given by the inverse of the distance reference point O to the “Characteristic Straight Line". Its direction is given by the bearing of the normal directed from point O to the Characteristic Straight Line (Fig..6). A “best estimate" of the topometric observations was used to measure the elevation of points carefully selected, before and after the deformation. Gross errors have been eliminated by statistical analyses and by comparing the heights within local neighborhoods. The results of a test using an area where very interesting land surface deformation occurs are reported. Monitoring with different options and qualitative comparison of results based on a sufficient number of check points are presented.
Abstract: The problem of estimating time-varying regression is
inevitably concerned with the necessity to choose the appropriate
level of model volatility - ranging from the full stationarity of instant
regression models to their absolute independence of each other. In the
stationary case the number of regression coefficients to be estimated
equals that of regressors, whereas the absence of any smoothness
assumptions augments the dimension of the unknown vector by the
factor of the time-series length. The Akaike Information Criterion
is a commonly adopted means of adjusting a model to the given
data set within a succession of nested parametric model classes,
but its crucial restriction is that the classes are rigidly defined by
the growing integer-valued dimension of the unknown vector. To
make the Kullback information maximization principle underlying the
classical AIC applicable to the problem of time-varying regression
estimation, we extend it onto a wider class of data models in which
the dimension of the parameter is fixed, but the freedom of its values
is softly constrained by a family of continuously nested a priori
probability distributions.
Abstract: A filter is used to remove undesirable frequency information from a dynamic signal. This paper shows that the Znotch filter filtering technique can be applied to remove the noise nuisance from a machining signal. In machining, the noise components were identified from the sound produced by the operation of machine components itself such as hydraulic system, motor, machine environment and etc. By correlating the noise components with the measured machining signal, the interested components of the measured machining signal which was less interfered by the noise, can be extracted. Thus, the filtered signal is more reliable to be analysed in terms of noise content compared to the unfiltered signal. Significantly, the I-kaz method i.e. comprises of three dimensional graphical representation and I-kaz coefficient, Z∞ could differentiate between the filtered and the unfiltered signal. The bigger space of scattering and the higher value of Z∞ demonstrated that the signal was highly interrupted by noise. This method can be utilised as a proactive tool in evaluating the noise content in a signal. The evaluation of noise content is very important as well as the elimination especially for machining operation fault diagnosis purpose. The Z-notch filtering technique was reliable in extracting noise component from the measured machining signal with high efficiency. Even though the measured signal was exposed to high noise disruption, the signal generated from the interaction between cutting tool and work piece still can be acquired. Therefore, the interruption of noise that could change the original signal feature and consequently can deteriorate the useful sensory information can be eliminated.
Abstract: A human verification system is presented in this
paper. The system consists of several steps: background subtraction,
thresholding, line connection, region growing, morphlogy, star
skelatonization, feature extraction, feature matching, and decision
making. The proposed system combines an advantage of star
skeletonization and simple statistic features. A correlation matching
and probability voting have been used for verification, followed by a
logical operation in a decision making stage. The proposed system
uses small number of features and the system reliability is
convincing.
Abstract: The paper discusses a computationally efficient
method for the design of prototype filters required for the
implementation of an M-band cosine modulated filter bank. The
prototype filter is formulated as an optimum interpolated FIR filter.
The optimum interpolation factor requiring minimum number of
multipliers is used. The model filter as well as the image suppressor
will be designed using the Kaiser window. The method will seek to
optimize a single parameter namely cutoff frequency to minimize the
distortion in the overlapping passband.
Abstract: This paper deals with the localization of the wideband sources. We develop a new approach for estimating the wide band sources parameters. This method is based on the high order statistics of the recorded data in order to eliminate the Gaussian components from the signals received on the various hydrophones.In fact the noise of sea bottom is regarded as being Gaussian. Thanks to the coherent signal subspace algorithm based on the cumulant matrix of the received data instead of the cross-spectral matrix the wideband correlated sources are perfectly located in the very noisy environment. We demonstrate the performance of the proposed algorithm on the real data recorded during an underwater acoustics experiments.
Abstract: In this paper the design of maximally flat linear phase
finite impulse response (FIR) filters is considered. The problem is
handled with totally two different approaches. The first one is
completely deterministic numerical approach where the problem is
formulated as a Linear Complementarity Problem (LCP). The other
one is based on a combination of Markov Random Fields (MRF's)
approach with messy genetic algorithm (MGA). Markov Random
Fields (MRFs) are a class of probabilistic models that have been
applied for many years to the analysis of visual patterns or textures.
Our objective is to establish MRFs as an interesting approach to
modeling messy genetic algorithms. We establish a theoretical result
that every genetic algorithm problem can be characterized in terms of
a MRF model. This allows us to construct an explicit probabilistic
model of the MGA fitness function and introduce the Ising MGA.
Experimentations done with Ising MGA are less costly than those
done with standard MGA since much less computations are involved.
The least computations of all is for the LCP. Results of the LCP,
random search, random seeded search, MGA, and Ising MGA are
discussed.
Abstract: This paper presents a useful sub-pixel image
registration method using line segments and a sub-pixel edge detector.
In this approach, straight line segments are first extracted from gray
images at the pixel level before applying the sub-pixel edge detector.
Next, all sub-pixel line edges are mapped onto the orientation-distance
parameter space to solve for line correspondence between images.
Finally, the registration parameters with sub-pixel accuracy are
analytically solved via two linear least-square problems. The present
approach can be applied to various fields where fast registration with
sub-pixel accuracy is required. To illustrate, the present approach is
applied to the inspection of printed circuits on a flat panel. Numerical
example shows that the present approach is effective and accurate
when target images contain a sufficient number of line segments,
which is true in many industrial problems.
Abstract: In this paper, we argue that Design research is basic to countries- national productivity and competition agendas at the same time that vagaries of research training presents as one of the barriers faced by Design Higher Degree by Research students in engaging those agendas. We argue that, given industry requirements for research-trained recruits, students have the right to expect that research training will provide the foundations of a successful career on an academic or research pathway or a professional pathway, but that universities have yet to address problems in their provision of research training for Design doctoral students. We suggest that to facilitate this, rigorous research conducted on the provision of Doctoral programs in Design would serve to inform future activities in Design research in productive ways.
Abstract: The paper is concerned with relationships between
SSME and ICTs and focuses on the role of Web 2.0 tools in
the service development process. The research presented aims at
exploring how collaborative technologies can support and improve
service processes, highlighting customer centrality and value coproduction.
The core idea of the paper is the centrality of user
participation and the collaborative technologies as enabling factors;
Wikipedia is analyzed as an example. The result of such analysis is
the identification and description of a pattern characterising specific
services in which users collaborate by means of web tools with value
co-producers during the service process. The pattern of collaborative
co-production concerning several categories of services including
knowledge based services is then discussed.
Abstract: A fully on-chip low drop-out (LDO) voltage regulator with 100pF output load capacitor is presented. A novel frequency compensation scheme using current buffer is adopted to realize single dominant pole within the unit gain frequency of the regulation loop, the phase margin (PM) is at least 50 degree under the full range of the load current, and the power supply rejection (PSR) character is improved compared with conventional Miller compensation. Besides, the differentiator provides a high speed path during the load current transient. Implemented in 0.18μm CMOS technology, the LDO voltage regulator provides 100mA load current with a stable 1.8V output voltage consuming 80μA quiescent current.
Abstract: A decomposition of a graph G is a collection ψ of subgraphs H1,H2, . . . , Hr of G such that every edge of G belongs to exactly one Hi. If each Hi is either an induced path or an induced cycle in G, then ψ is called an induced path decomposition of G. The minimum cardinality of an induced path decomposition of G is called the induced path decomposition number of G and is denoted by πi(G). In this paper we initiate a study of this parameter.