Abstract: This report shows the performance of composite
biodegradable film from chitosan, starch and sawdust fiber. The main
objectives of this research are to fabricate and characterize composite
biodegradable film in terms of morphology and physical properties.
The film was prepared by casting method. Sawdust fiber was used as
reinforcing agent and starch as polymer matrix in the casting
solution. The morphology of the film was characterized using atomic
force microscope (AFM). The result showed that the film has
smooth structure. Chemical composition of the film was investigated
using Fourier transform infrared (FTIR) where the result revealed
present of starch in the film. The thermal properties were
characterized using thermal gravimetric analyzer (TGA) and
differential scanning calorimetric (DSC) where the results showed
that the film has small difference in melting and degradation
temperature.
Abstract: This paper reviews various approaches that have been
used for the modeling and simulation of large-scale engineering
systems and determines their appropriateness in the development of a
RICS modeling and simulation tool. Bond graphs, linear graphs,
block diagrams, differential and difference equations, modeling
languages, cellular automata and agents are reviewed. This tool
should be based on linear graph representation and supports symbolic
programming, functional programming, the development of noncausal
models and the incorporation of decentralized approaches.
Abstract: The changes in quality properties and nutritional
components in two fermented mugworts (Artemisia capillaries
Thumberg, Artemisiaeasiaticae Nakai) were characterized followed
by the rapid pattern analysis of volatile flavor compounds by Electric
Nose based on SAW(Surface Acoustic Wave) sensor in GC system.
There were remarkable decreases in the pH and small changes in the
total soluble solids after fermentation. The L (lightness) and b
(yellowness) values in Hunter's color system were shown to be
decreased, whilst the a (redness) value was increased by fermentation.
The HPLC analysis demonstrated that total amino acids were
increased in quantity and the essential amino acids were contained
higher in A. asiaticaeNakai than in A. capillaries Thumberg. While
the total polyphenol contents were not affected by fermentation, the
total sugar contents were dramatically decreased. Scopoletinwere
highly abundant in A. capillarisThumberg, however, it was not
detected in A. asiaticaeNakai. Volatile flavor compounds by Electric
Nose showed that the intensity of several peaks were increased much
and seven additional flavor peaks were newly produced after
fermentation. The flavor differences of two mugworts were clearly
distinguished from the image patterns of VaporPrintTM which indicate
that the fermentation enables the two mugworts to have subtle flavor
differences.
Abstract: In this research saffron samples were prepared from
farms and sampling was done in four states contain : sampling from
fresh saffron of petal with forceps , sampling from fresh saffron of
petal by hands, sampling from dried sample by warm air in shadow,
sampling from dried sample which dried by dryer. Samples collected
and kept in sterile tubes and containers and carried to laboratory and
maintained until experiment. Microbial experiments were performed
to determine microbial load such as total count, Staphylococcus
aureus, coli form, E.coli, mold and yeast. Results showed that in
picking and drying stages the contamination amount increases in
saffron samples. There was a significant difference between the
microbial load of picked up saffron by forceps and by hands, and
also between dried saffron by warm air in shadow and by dryer.
Abstract: In this paper, we have combined some spatial derivatives with the optimised time derivative proposed by Tam and Webb in order to approximate the linear advection equation which is given by = 0. Ôêé Ôêé + Ôêé Ôêé x f t u These spatial derivatives are as follows: a standard 7-point 6 th -order central difference scheme (ST7), a standard 9-point 8 th -order central difference scheme (ST9) and optimised schemes designed by Tam and Webb, Lockard et al., Zingg et al., Zhuang and Chen, Bogey and Bailly. Thus, these seven different spatial derivatives have been coupled with the optimised time derivative to obtain seven different finite-difference schemes to approximate the linear advection equation. We have analysed the variation of the modified wavenumber and group velocity, both with respect to the exact wavenumber for each spatial derivative. The problems considered are the 1-D propagation of a Boxcar function, propagation of an initial disturbance consisting of a sine and Gaussian function and the propagation of a Gaussian profile. It is known that the choice of the cfl number affects the quality of results in terms of dissipation and dispersion characteristics. Based on the numerical experiments solved and numerical methods used to approximate the linear advection equation, it is observed in this work, that the quality of results is dependent on the choice of the cfl number, even for optimised numerical methods. The errors from the numerical results have been quantified into dispersion and dissipation using a technique devised by Takacs. Also, the quantity, Exponential Error for Low Dispersion and Low Dissipation, eeldld has been computed from the numerical results. Moreover, based on this work, it has been found that when the quantity, eeldld can be used as a measure of the total error. In particular, the total error is a minimum when the eeldld is a minimum.
Abstract: A procedure for the preparation of clarified Pawpaw
Juice was developed. About 750ml Pawpaw pulp was measured into
2 measuring cylinders A & B of capacity 1 litre heated to 400C,
cooled to 200C. 30mls pectinase was added into cylinder A, while
30mls distilled water was added into cylinder B. Enzyme treated
sample (A) was allowed to digest for 5hours after which it was heated
to 900C for 15 minutes to inactivate the enzyme. The heated sample
was cooled and with the aid of a mucillin cloth the pulp was filtered
to obtain the clarified pawpaw juice. The juice was filled into 100ml
plastic bottles, pasteurized at 950C for 45 minutes, cooled and stored
at room temperature. The sample treated with 30mls distilled water
also underwent the same process. Freshly pasteurized sample was
analyzed for specific gravity, titratable acidity, pH, sugars and
ascorbic acid. The remaining sample was then stored for 2 weeks and
the above analyses repeated. There were differences in the results of
the freshly pasteurized samples and stored sample in pH and ascorbic
acid levels, also sample treated with pectinase yielded higher
volumes of juice than that treated with distilled water.
Abstract: Concerns about low levels of children-s physical activity and motor skill development, prompted the Ministry of Education to trial a physical activity pilot project (PAPP) in 16 New Zealand primary schools. The project comprised professional development and training in physical education for lead teachers and introduced four physical activity coordinators to liaise with and increase physical activity opportunities in the pilot schools. A survey of generalist teachers (128 baseline, 155 post-intervention) from these schools looked at timetabled physical activity sessions and issues related to teaching physical education. The authors calculated means and standard deviations of data relating to timetabled PE sessions and used a one-way analysis of variance to determine significant differences. Results indicated time devoted to physical activity related subjects significantly increased over the course of the intervention. Teacher-s reported improved confidence and competence, which resulted in an improvement in quality physical education delivered more often.
Abstract: A steady two-dimensional magnetohydrodynamics
flow and heat transfer over a stretching vertical sheet influenced by
radiation and porosity is studied. The governing boundary layer
equations of partial differential equations are reduced to a system of
ordinary differential equations using similarity transformation. The
system is solved numerically by using a finite difference scheme
known as the Keller-box method for some values of parameters,
namely the radiation parameter N, magnetic parameter M, buoyancy
parameter l , Prandtl number Pr and permeability parameter K. The
effects of the parameters on the heat transfer characteristics are
analyzed and discussed. It is found that both the skin friction
coefficient and the local Nusselt number decrease as the magnetic
parameter M and permeability parameter K increase. Heat transfer
rate at the surface decreases as the radiation parameter increases.
Abstract: Power cables are vulnerable to failure due to aging or
defects that occur with the passage of time under continuous
operation and loading stresses. PD detection and characterization
provide information on the location, nature, form and extent of the
degradation. As a result, PD monitoring has become an important
part of condition based maintenance (CBM) program among power
utilities. Online partial discharge (PD) localization of defect sources
in power cable system is possible using the time of flight method.
The information regarding the time difference between the main and
reflected pulses and cable length can help in locating the partial
discharge source along the cable length. However, if the length of
the cable is not known and the defect source is located at the extreme
ends of the cable or in the middle of the cable, then double ended
measurement is required to indicate the location of PD source. Use of
multiple sensors can also help in discriminating the cable PD or local/
external PD. This paper presents the experience and results from
online partial discharge measurements conducted in the laboratory
and the challenges in partial discharge source localization.
Abstract: This paper aims to perform the second law analysis of
thermodynamics on the laminar film condensation of pure saturated
vapor flowing in the direction of gravity on an ellipsoid with variable
wall temperature. The analysis provides us understanding how the
geometric parameter- ellipticity and non-isothermal wall temperature
variation amplitude “A." affect entropy generation during film-wise
condensation heat transfer process. To understand of which
irreversibility involved in this condensation process, we derived an
expression for the entropy generation number in terms of ellipticity
and A. The result indicates that entropy generation increases with
ellipticity. Furthermore, the irreversibility due to finite temperature
difference heat transfer dominates over that due to condensate film
flow friction and the local entropy generation rate decreases with
increasing A in the upper half of ellipsoid. Meanwhile, the local
entropy generation rate enhances with A around the rear lower half of
ellipsoid.
Abstract: This paper focuses on wormhole attacks detection in wireless sensor networks. The wormhole attack is particularly challenging to deal with since the adversary does not need to compromise any nodes and can use laptops or other wireless devices to send the packets on a low latency channel. This paper introduces an easy and effective method to detect and locate the wormholes: Since beacon nodes are assumed to know their coordinates, the straight line distance between each pair of them can be calculated and then compared with the corresponding hop distance, which in this paper equals hop counts × node-s transmission range R. Dramatic difference may emerge because of an existing wormhole. Our detection mechanism is based on this. The approximate location of the wormhole can also be derived in further steps based on this information. To the best of our knowledge, our method is much easier than other wormhole detecting schemes which also use beacon nodes, and to those have special requirements on each nodes (e.g., GPS receivers or tightly synchronized clocks or directional antennas), ours is more economical. Simulation results show that the algorithm is successful in detecting and locating wormholes when the density of beacon nodes reaches 0.008 per m2.
Abstract: Most of the image watermarking methods, using the properties of the human visual system (HVS), have been proposed in literature. The component of the visual threshold is usually related to either the spatial contrast sensitivity function (CSF) or the visual masking. Especially on the contrast masking, most methods have not mention to the effect near to the edge region. Since the HVS is sensitive what happens on the edge area. This paper proposes ultrasound image watermarking using the visual threshold corresponding to the HVS in which the coefficients in a DCT-block have been classified based on the texture, edge, and plain area. This classification method enables not only useful for imperceptibility when the watermark is insert into an image but also achievable a robustness of watermark detection. A comparison of the proposed method with other methods has been carried out which shown that the proposed method robusts to blockwise memoryless manipulations, and also robust against noise addition.
Abstract: Drying characteristics of rough rice (variety of lenjan) with an initial moisture content of 25% dry basis (db) was studied in a hot air dryer assisted by infrared heating. Three arrival air temperatures (30, 40 and 500C) and four infrared radiation intensities (0, 0.2 , 0.4 and 0.6 W/cm2) and three arrival air speeds (0.1, 0.15 and 0.2 m.s-1) were studied. Bending strength of brown rice kernel, percentage of cracked kernels and time of drying were measured and evaluated. The results showed that increasing the drying arrival air temperature and radiation intensity of infrared resulted decrease in drying time. High bending strength and low percentage of cracked kernel was obtained when paddy was dried by hot air assisted infrared dryer. Between this factors and their interactive effect were a significant difference (p
Abstract: Hydrogen that used as fuel in fuel cell vehicles can be
produced from renewable sources such as wind, solar, and hydro
technologies. PV-electrolyzer is one of the promising methods to
produce hydrogen with zero pollution emission. Hydrogen
production from a PV-electrolyzer system depends on the efficiency
of the electrolyzer and photovoltaic array, and sun irradiance at that
site. In this study, the amount of hydrogen is obtained using
mathematical equations for difference driving distance and sun peak
hours. The results show that the minimum of 99 PV modules are used
to generate 1.75 kgH2 per day for two vehicles.
Abstract: A numerical study on the heat transfer in the thermal
barrier coatings and the substrates of a parallel-plate enclosure is
carried out. Some of the thermal barrier coatings, such as ceramics, are
semitransparent and are of interest for high-temperature applications
where radiation effects are significant. The radiative transfer equations
and the energy equations are solved by using the discrete ordinates
method and the finite difference method. Illustrative results are
presented for temperature distributions in the coatings and the opaque
walls under various heating conditions. The results show that the
temperature distribution is more uniform in the interior portion of each
coating away from its boundary for the case with a larger average of
varying refractive index and a positive gradient of refractive index
enhances radiative transfer to the substrates.
Abstract: Social media has led to paradigm shifts in ways
people work and do business, interact and socialize, learn and obtain
knowledge. So much so that social media has established itself as an
important spatial extension of this nation-s historicity and challenges.
Regardless of the enabling reputation and recommendation features
through social networks embedded in the social media system, the
overflow of broadcasted and publicized media contents turns the
table around from engendering trust to doubting the trust system.
When the trust is at doubt, the effects include deactivation of
accounts and creation of multiple profiles, which lead to the overflow
of 'ghost' contents (i.e. “the abundance of abandoned ships"). In
most literature, the study of trust can be related to culture; hence the
difference between Western-s “openness" and Eastern-s “blue-chip"
concepts in networking and relationships. From a survey on issues
and challenges among Malaysian social media users, 'authenticity'
emerges as one of the main factors that causes and is caused by other
factors. The other issue that has surfaced is credibility either in terms
of message/content and source. Another is the quality of the
knowledge that is shared. This paper explores the terrains of this
critical space which in recent years has been dominated increasingly
by, arguably, social networks embedded in the social media system,
the overflow of broadcasted and publicized media content.
Abstract: Equilibrium and stability equations of a thin rectangular plate with length a, width b, and thickness h(x)=C1x+C2, made of functionally graded materials under thermal loads are derived based on the first order shear deformation theory. It is assumed that the material properties vary as a power form of thickness coordinate variable z. The derived equilibrium and buckling equations are then solved analytically for a plate with simply supported boundary conditions. One type of thermal loading, uniform temperature rise and gradient through the thickness are considered, and the buckling temperatures are derived. The influences of the plate aspect ratio, the relative thickness, the gradient index and the transverse shear on buckling temperature difference are all discussed.
Abstract: In this paper, we present the video quality measure
estimation via a neural network. This latter predicts MOS (mean
opinion score) by providing height parameters extracted from
original and coded videos. The eight parameters that are used are: the
average of DFT differences, the standard deviation of DFT
differences, the average of DCT differences, the standard deviation
of DCT differences, the variance of energy of color, the luminance
Y, the chrominance U and the chrominance V. We chose Euclidean
Distance to make comparison between the calculated and estimated
output.
Abstract: Type 2 diabetes mellitus (T2DM) is a complex
metabolic disorder that characterized by the presence of high glucose
in blood that cause from insulin resistance and insufficiency due to
deterioration β-cell Langerhans functions. T2DM is commonly
caused by the combination of inherited genetic variations as well as
our own lifestyle. Metallothionein (MT) is a known cysteine-rich
protein responsible in helping zinc homeostasis which is important in
insulin signaling and secretion as well as protection our body from
reactive oxygen species (ROS). MT scavenged ROS and free
radicals in our body happen to be one of the reasons of T2DM and its
complications. The objective of this study was to investigate the
association of MT1A and MT2A polymorphisms between T2DM and
control subjects among Malay populations. This study involved 150
T2DM and 120 Healthy individuals of Malay ethnic with mixed
genders. The genomic DNA was extracted from buccal cells and
amplified for MT1A and MT2A loci; the 347bp and 238bp banding
patterns were respectively produced by mean of the Polymerase
Chain Reaction (PCR). The PCR products were digested with Mlucl
and Tsp451 restriction enzymes respectively and producing
fragments lengths of (158/189/347bp) and (103/135/238bp)
respectively. The ANOVA test was conducted and it shown that there
was a significant difference between diabetic and control subjects for
age, BMI, WHR, SBP, FPG, HBA1C, LDL, TG, TC and family
history with (P0.05). The genotype
frequency for AA, AG and GG of MT1A polymorphisms was 72.7%,
22.7% and 4.7% in cases and 15%, 55% and 30% in control
respectively. As for MT2A, genotype frequency of GG, GC and CC
was 42.7%, 27.3% and 30% in case and 5%, 40% and 55% for
control respectively. Both polymorphisms show significant difference
between two investigated groups with (P=0.000). The Post hoc test
was conducted and shows a significant difference between the
genotypes within each polymorphism (P=0. 000). The MT1A and
MT2A polymorphisms were believed to be the reliable molecular
markers to distinguish the T2DM subjects from healthy individuals in
Malay populations.
Abstract: The Bayesian Optimization Algorithm (BOA) is an algorithm based on the estimation of distributions. It uses techniques from modeling data by Bayesian networks to estimating the joint distribution of promising solutions. To obtain the structure of Bayesian network, different search algorithms can be used. The key point that BOA addresses is whether the constructed Bayesian network could generate new and useful solutions (strings), which could lead the algorithm in the right direction to solve the problem. Undoubtedly, this ability is a crucial factor of the efficiency of BOA. Varied search algorithms can be used in BOA, but their performances are different. For choosing better ones, certain suitable method to present their ability difference is needed. In this paper, a greedy search algorithm and a stochastic search algorithm are used in BOA to solve certain optimization problem. A method using Kullback-Leibler (KL) Divergence to reflect their difference is described.