Abstract: This paper concerns the study of sustainable construction materials applied on the "Health Post", a prototype for the primary health care situated in alienated areas of the world. It's suitable for social and climatic Sub-Saharan context; however, it could be moved in other countries of the world with similar urgent needs. The idea is to create a Health Post with local construction materials that have a low environmental impact and promote the local workforce allowing reuse of traditional building techniques lowering production costs and transport. The aim of Primary Health Care Centre is to be a flexible and expandable structure identifying a modular form that can be repeated several times to expand its existing functions. In this way it could be not only a health care centre but also a socio-cultural facility.
Abstract: Delamination between layers in composite materials is a major structural failure. The delamination resistance is quantified by the critical strain energy release rate (SERR). The present investigation deals with the strain energy release rate of two woven fabric composites. Materials used are made of two types of glass fiber (360 gsm and 600 gsm) of plain weave and epoxy as matrix. The fracture behavior is studied using the mode I, double cantilever beam test and the mode II, end notched flexure test, in order to determine the energy required for the initiation and growth of an artificial crack. The delamination energy of these two materials is compared in order to study the effect of weave and reinforcement on mechanical properties. The fracture mechanism is also analyzed by means of scanning electron microscopy (SEM). It is observed that the plain weave fabric composite with lesser strand width has higher inter laminar fracture properties compared to the plain weave fabric composite with more strand width.
Abstract: In this paper, a theoretical formula is presented to
predict the instantaneous folding force of the first fold creation in a
square column under axial loading. Calculations are based on analysis
of “Basic Folding Mechanism" introduced by Wierzbicki and
Abramowicz. For this purpose, the sum of dissipated energy rate under
bending around horizontal and inclined hinge lines and dissipated
energy rate under extensional deformations are equated to the work rate
of the external force on the structure. Final formula obtained in this
research, reasonably predicts the instantaneous folding force of the first
fold creation versus folding distance and folding angle and also predicts
the instantaneous folding force instead of the average value. Finally,
according to the calculated theoretical relation, instantaneous folding
force of the first fold creation in a square column was sketched
versus folding distance and was compared to the experimental results
which showed a good correlation.
Abstract: Plastics occupy wide place in the applications of
automotive, electronics and house goods. Especially reinforced
plastics become popular because of their high strength besides their
advantages of low weight and easy manufacturability. In this study,
mechanical and morphological properties of polypropylene (PP) and
high density polyethylene (HDPE) matrix composites reinforced with
surface modified nano titan dioxide (TiO2) particles were
investigated. Surface modification was made by coating the nano
powders with maleic anhydride grafted styrene ethylene butylene
styrene (SEBS-g-MA) and silane, respectively. After surface
modification, PP/TiO2 and HDPE/TiO2 composites were obtained by
using twin screw extruder at titan dioxide loading of 1 wt.%, 3 wt.%
and 5 wt.%. Effects of surface modification were determined by
thermal and morphological analysis. SEBS-g-MA provided bridging
effect between TiO2 particles and polymer matrix while silane was
effective as a dispersant. Depending on that, homogenous structures
without agglomeration were obtained. Mechanical tests were
performed on the injection moldings of the composites for obtaining
the impact strength, tensile strength, stress at break, elongation and
elastic modulus. Reinforced HDPE and PP moldings gave higher
tensile strength and elastic modulus due to the rigid structure of TiO2.
Slight increment was seen in stress at break. Elongation and impact
strength decreased due to the stiffness of the nano titan dioxide.
Abstract: Commercial infrastructures intended for use as leisure
retreats such as golf and ski resorts have been extensively developed in many rural areas of Japan. However, following the burst of the economic bubble in the 1990s, several existing resorts faced tough
management decisions and some were forced to close their business.
In this study, six alternative management options for restructuring the
existing golf courses (park, cemetery, biofuel production, reforestation,
pasturing and abandonment) are examined and their environmental
and economic impacts are quantitatively assessed. In addition,
restructuring scenarios of these options and an ex-ante assessment
model are developed. The scenario analysis by Monte Carlo simulation shows a clear trade-off between GHG savings and benefit/cost (B/C) ratios, of which “Restoring Nature" scenario
absorbs the most CO2 among the four scenarios considered, but its B/C
ratio is the lowest. This study can be used to select or examine options
and scenarios of golf course management and rural environmental
management policies.
Abstract: Although water only takes a little percentage in the total mass of soil, it indeed plays an important role to the strength of structure. Moisture transfer can be carried out by many different mechanisms which may involve heat and mass transfer, thermodynamic phase change, and the interplay of various forces such as viscous, buoyancy, and capillary forces. The continuum models are not well suited for describing those phenomena in which the connectivity of the pore space or the fracture network, or that of a fluid phase, plays a major role. However, Lattice Boltzmann methods (LBMs) are especially well suited to simulate flows around complex geometries. Lattice Boltzmann methods were initially invented for solving fluid flows. Recently, fluid with multicomponent and phase change is also included in the equations. By comparing the numerical result with experimental result, the Lattice Boltzmann methods with phase change will be optimized.
Abstract: Using a force balanced translational-radial dynamics,
phase space of the moving single bubble sonoluminescence (m-
SBSL) in 85% wt sulfuric acid has been numerically calculated. This
phase space is compared with that of single bubble sonoluminescence
(SBSL) in pure water which has been calculated by using the mere
radial dynamics. It is shown that in 85% wt sulfuric acid, in a general
agreement with experiment, the bubble-s positional instability
threshold lays under the shape instability threshold. At the onset of
spatial instability of moving sonoluminescing (SL) bubble in 85%
wt sulfuric acid, temporal effects of the hydrodynamic force on the
bubble translational-radial dynamics have been investigated. The
appearance of non-zero history force on the moving SL bubble is
because of proper condition which was produced by high viscosity of
acid. Around the moving bubble collapse due to the rapid contraction
of the bubble wall, the inertial based added mass force overcomes the
viscous based history force and induces acceleration on the bubble
translational motion.
Abstract: The quality of a machined surface is becoming more and more important to justify the increasing demands of sophisticated component performance, longevity, and reliability. Usually, any machining operation leaves its own characteristic evidence on the machined surface in the form of finely spaced micro irregularities (surface roughness) left by the associated indeterministic characteristics of the different elements of the system: tool-machineworkpart- cutting parameters. However, one of the most influential sources in machining affecting surface roughness is the instantaneous state of tool edge. The main objective of the current work is to relate the in-process immeasurable cutting edge deformation and surface roughness to a more reliable easy-to-measure force signals using a robust non-linear time-dependent modeling regression techniques. Time-dependent modeling is beneficial when modern machining systems, such as adaptive control techniques are considered, where the state of the machined surface and the health of the cutting edge are monitored, assessed and controlled online using realtime information provided by the variability encountered in the measured force signals. Correlation between wear propagation and roughness variation is developed throughout the different edge lifetimes. The surface roughness is further evaluated in the light of the variation in both the static and the dynamic force signals. Consistent correlation is found between surface roughness variation and tool wear progress within its initial and constant regions. At the first few seconds of cutting, expected and well known trend of the effect of the cutting parameters is observed. Surface roughness is positively influenced by the level of the feed rate and negatively by the cutting speed. As cutting continues, roughness is affected, to different extents, by the rather localized wear modes either on the tool nose or on its flank areas. Moreover, it seems that roughness varies as wear attitude transfers from one mode to another and, in general, it is shown that it is improved as wear increases but with possible corresponding workpart dimensional inaccuracy. The dynamic force signals are found reasonably sensitive to simulate either the progressive or the random modes of tool edge deformation. While the frictional force components, feeding and radial, are found informative regarding progressive wear modes, the vertical (power) components is found more representative carrier to system instability resulting from the edge-s random deformation.
Abstract: Nurses in an Armed Force Hospital (AFH) expose to stronger stress than those in a civil hospital, especially in an emergency department (ED). Ironically, stresses of these nurses received few if any attention in academic research in the past. This study collects 227 samples from the emergency departments of four armed force hospitals in central and southern Taiwan. The research indicates that the top five stressors are a massive casualty event, delayed physician support, overloads of routine work, overloads of assignments, and annoying paper work. Excessive work loading was found to be the primary source of stress. Nurses who were perceived to have greater stress levels were more inclined to deploy emotion-oriented approaches and more likely to seek job rotations. Professional stressors and problem-oriented approaches were positively correlated. Unlike other local studies, this study concludes that the excessive work-loading is more stressful in an AFH.
Abstract: In the present paper; an experimental and numerical
investigations of drag reduction on a grooved circular cylinder have
been performed. The experiments were carried out in closed circuit
subsonic wind tunnel (TE44); the pressure distribution on the
cylinder was conducted using a TE44DPS differential pressure
scanner and the drag forces were measured using the TE81 balance.
The display unit is linked to a computer, loaded with DATASLIM
software for data analysis and logging of result. The numerical study
was performed using the code ANSYS FLUENT solving the
Reynolds Averaged Navier-Stokes (RANS) equations. The k-ε and k-
ω SST models were tested. The results obtained from the
experimental and numerical investigations have showed a reduction
in the drag when using longitudinal grooves namely 2 and 6 on the
cylinder.
Abstract: In this paper, Zinc Oxide (ZnO) thin films are deposited on glass substrate by sol-gel method. The ZnO thin films with well defined orientation were acquired by spin coating of zinc acetate dehydrate monoethanolamine (MEA), de-ionized water and isopropanol alcohol. These films were pre-heated at 275°C for 10 min and then annealed at 350°C, 450°C and 550°C for 80 min. The effect of annealing temperature and different thickness on structure and surface morphology of the thin films were verified by Atomic Force Microscopy (AFM). It was found that there was a significant effect of annealing temperature on the structural parameters of the films such as roughness exponent, fractal dimension and interface width. Thin films also were characterizied by X-ray Diffractometery (XRD) method. XRD analysis revealed that the annealed ZnO thin films consist of single phase ZnO with wurtzite structure and show the c-axis grain orientation. Increasing annealing temperature increased the crystallite size and the c-axis orientation of the film after 450°C. Also In this study, ZnO thin films in different thickness have been prepared by sol-gel method on the glass substrate at room temperature. The thicknesses of films are 100, 150 and 250 nm. Using fractal analysis, morphological characteristics of surface films thickness in amorphous state were investigated. The results show that with increasing thickness, surface roughness (RMS) and lateral correlation length (ξ) are decreased. Also, the roughness exponent (α) and growth exponent (β) were determined to be 0.74±0.02 and 0.11±0.02, respectively.
Abstract: This paper presents the results of an experimental study on the performance of a triboelectric separator of plastic mixtures used for recycling. The separator consists of four cylindrical electrodes. The principle behind the separation technique is based on the difference in the Coulomb force acting on the plastic particles after triboelectric charging. The separation of mixtures of acrylonitrile butadiene styrene (ABS) and polystyrene (PS) using this method was studied. The effects of the triboelectric charging time and applied voltage on the separation efficiency were investigated. The experimental results confirm that it is possible to obtain a high purity and recovery rate for the initial compositions considered in this study.
Abstract: The purposes of this study are 1) to study the over 20-year attempt of Mahakan fort community to negotiate with Bangkok Metropolitan Administration (BMA) to remain in their residential area belonging to the state, and 2) to apply the new social and cultural dimension between the state and the community as an alternative for local participation in keeping their residential area. This is a qualitative research, and the findings reveal that the community claimed their ancestors’ right as owners of this piece of land for over 200 years. The community, therefore, requested to take part in the preservation of land, culture and local intellect and the area management in terms of being a learning resource on the cultural road in Rattanakosin Island. However, BMA imposed the law concerning the community area relocation in Rattanakosin Island. The result of law enforcement led to the failure of the area relocation, and the hard hit on physical structure of the area including the overall deterioration of the cultural road renovated in the year 1982, the 200 years’ celebration of Bangkok. The enforcement of law by the state required the move of the community, and the landscape improvement based on the capital city plan. However, this enforcement resulted in the unending conflicts between the community and the state, and the solution of this problem was unclear. At the same time the community has spent a long time opposing the state’s action, and preparing themselves by administrating the community behind Mahakan fortress with community administrative committee under the suggestion of external organization by registering all community members, providing funds for community administration. At the meantime the state lacked the continuation of the enforcement due to political problem and BMA’s administration problem. It is, therefore, suggested that an alternative solution to this problem lie at the negotiation between the state and the community with the purpose of the collaboration between the two to develop the area under the protective law of each side.
Abstract: The main issue discussed is on the role of education system in the process of nation building as a means in uniting different community ethnics which later on, hoped to shape the future ethnic relation of this country. It is generally known that political socialization experienced by each ethnic community has given birth to a vernacular education system, separated along the ethnic line. Every community shapes their own education system based on their respective mother tongue language, however all are based on the same curriculum. As a result the role of education as a uniting force is not significantly effective. Historically, it has been shown that government efforts to unite the country education system under the wing of national education system (national school) is not that successful since every community (Chinese) will defend the existence of their community education system because they want to spur their mother tongue language. The clash between national education system and vernacular education system is the root cause of stalemate in the ethnic relation in Malaysia and it always becomes a flash point when the issue is raised. The question now is what is the best solution to enhance the national education system in multiethnic Malaysia?
Abstract: Due to their high power-to-weight ratio and low cost,
pneumatic actuators are attractive for robotics and automation
applications; however, achieving fast and accurate control of their
position have been known as a complex control problem. A
methodology for obtaining high position accuracy with a linear
pneumatic actuator is presented. During experimentation with a
number of PID classical control approaches over many operations of
the pneumatic system, the need for frequent manual re-tuning of the
controller could not be eliminated. The reason for this problem is
thermal and energy losses inside the cylinder body due to the
complex friction forces developed by the piston displacements.
Although PD controllers performed very well over short periods, it
was necessary in our research project to introduce some form of
automatic gain-scheduling to achieve good long-term performance.
We chose a fuzzy logic system to do this, which proved to be an
easily designed and robust approach. Since the PD approach showed
very good behaviour in terms of position accuracy and settling time,
it was incorporated into a modified form of the 1st order Tagaki-
Sugeno fuzzy method to build an overall controller. This fuzzy gainscheduler
uses an input variable which automatically changes the PD
gain values of the controller according to the frequency of repeated
system operations. Performance of the new controller was
significantly improved and the need for manual re-tuning was
eliminated without a decrease in performance. The performance of
the controller operating with the above method is going to be tested
through a high-speed web network (GRID) for research purposes.
Abstract: In this study, Friction Stir Processing (FSP) a recent grain refinement technique was employed to disperse micron-sized (2 *m) SiCp particles into aluminum alloy AA6063. The feasibility to fabricate bulk composites through FSP was analyzed and experiments were conducted at different traverse speeds and wider volumes of the specimens. Micro structural observation were carried out by employing optical microscopy test of the cross sections in both parallel and perpendicular to the tool traverse direction. Mechanical property including micro hardness was evaluated in detail at various regions on the specimen. The composites had an excellent bonding with aluminum alloy substrate and a significant increase of 30% in the micro hardness value of metal matrix composite (MMC) as to that of the base metal has observed. The observations clearly indicate that SiC particles were uniformly distributed within the aluminum matrix.
Abstract: The hydrodynamic and thermal lattice Boltzmann
methods are applied to investigate the turbulent convective heat
transfer in the wavy channel flows. In this study, the turbulent
phenomena are modeling by large-eddy simulations with the
Smagorinsky model. As a benchmark, the laminar and turbulent
backward-facing step flows are simulated first. The results give good
agreement with other numerical and experimental data. For wavy
channel flows, the distribution of Nusselt number and the skin-friction
coefficients are calculated to evaluate the heat transfer effect and the
drag force. It indicates that the vortices at the trough would affect the
magnitude of drag and weaken the heat convection effects on the wavy
surface. In turbulent cases, if the amplitude of the wavy boundary is
large enough, the secondary vortices would be generated at troughs
and contribute to the heat convection. Finally, the effects of different
Re on the turbulent transport phenomena are discussed.
Abstract: Environmental awareness and the recent
environmental policies have forced many electric utilities to
restructure their operational practices to account for their emission
impacts. One way to accomplish this is by reformulating the
traditional economic dispatch problem such that emission effects are
included in the mathematical model. This paper presents a Particle
Swarm Optimization (PSO) algorithm to solve the Economic-
Emission Dispatch problem (EED) which gained recent attention due
to the deregulation of the power industry and strict environmental
regulations. The problem is formulated as a multi-objective one with
two competing functions, namely economic cost and emission
functions, subject to different constraints. The inequality constraints
considered are the generating unit capacity limits while the equality
constraint is generation-demand balance. A novel equality constraint
handling mechanism is proposed in this paper. PSO algorithm is
tested on a 30-bus standard test system. Results obtained show that
PSO algorithm has a great potential in handling multi-objective
optimization problems and is capable of capturing Pareto optimal
solution set under different loading conditions.
Abstract: The posteroanterior manipulation technique is usually include in the procedure of the lumbar spine to evaluate the intervertebral motion according to mechanical resistance. The mechanical device with visual feedback was proposed that allows one to analysis the lumbar segments mobility “in vivo" facilitating for the therapist to take its treatment evolution. The measuring system uses load cell and displacement sensor to estimate spine stiffness. In this work, the device was tested by 2 therapists, female, applying posteroanterior force techniques to 5 volunteers, female, with frequency of approximately 1.2-1.8 Hz. A test-retest procedure was used for 2 periods of day. The visual feedback results small variation of forces and cycle time during 6 cycles rhythmic application. The stiffness values showed good agreement between test-retest procedures when used same order of maximum forces.
Abstract: This paper presents a CFD analysis of the flow around
a 30° inclined flat plate of infinite span. Numerical predictions have
been compared to experimental measurements, in order to assess the
potential of the finite volume code of determining the aerodynamic
forces acting on a flat plate invested by a fluid stream of infinite
extent.
Several turbulence models and spatial node distributions have
been tested and flow field characteristics in the neighborhood of the
flat plate have been numerically investigated, allowing the
development of a preliminary procedure to be used as guidance in
selecting the appropriate grid configuration and the corresponding
turbulence model for the prediction of the flow field over a twodimensional
inclined plate.