Abstract: The recent drive for use of performance-based methodologies in design and assessment of structures in seismic areas has significantly increased the demand for the development of reliable nonlinear inelastic static pushover analysis tools. As a result, the adaptive pushover methods have been developed during the last decade, which unlike their conventional pushover counterparts, feature the ability to account for the effect that higher modes of vibration and progressive stiffness degradation might have on the distribution of seismic storey forces. Even in advanced pushover methods, little attention has been paid to the Unsymmetric structures. This study evaluates the seismic demands for three dimensional Unsymmetric-Plan buildings determined by the Displacement-based Adaptive Pushover (DAP) analysis, which has been introduced by Antoniou and Pinho [2004]. The capability of DAP procedure in capturing the torsional effects due to the irregularities of the structures, is investigated by comparing its estimates to the exact results, obtained from Incremental Dynamic Analysis (IDA). Also the capability of the procedure in prediction the seismic behaviour of the structure is discussed.
Abstract: This study numerically investigates the effects of Electrohydrodynamic on flow patterns and heat transfer enhancement within a cavity which is on the lower wall of channel. In this simulation, effects of using ground wire and ground plate on the flow patterns are compared. Moreover, the positions of electrode wire respecting with ground are tested in the range of angles θ = 0 - 180o. High electrical voltage exposes to air is 20 kV. Bulk mean velocity and temperature of inlet air are controlled at 0.1 m/s and 60 OC, respectively. The result shows when electric field is applied, swirling flow is appeared in the channel. In addition, swirling flow patterns in the main flow of using ground plate are widely spreader than that of using ground wire. Moreover, direction of swirling flow also affects the flow pattern and heat transfer in a cavity. These cause the using ground wire to give the maximum temperature and heat transfer higher than using ground plate. Furthermore, when the angle is at θ = 60o, high shear flow effect is obtained. This results show high strength of swirling flow and effective heat transfer enhancement.
Abstract: Children with hemiplgic cerebral palsy often walk
with diminished reciprocal arm swing so the purpose of this study
was to describe kinematic characteristics in children with hemiplegic
cerebral palsy (CP) during the gait suphases, and find if there is a
correlation between upper(shoulder and elbow) and lower(hip, knee,
and ankle) limb joints either in involved or uninvolved.48 children
with hemiplegic cerebral palsy (18boys, 30girls) with an average age
of (5.1±0.87) years were selected randomly to evaluate joint angles
during gait by 3D motion analysis system with 6 pro reflex cameras
in a sagittal plane for both sides of the body. The results showed
increased shoulder and elbow flexion, increased hip angular
displacement, decreased knee and ankle arcs during gait cycle, also
there is correlation between shoulder and elbow to hip, knee, and
ankle joints during various subphases of gait.
Abstract: Nowadays, the performance required for concrete
structures is more complicated and diversified. Self-compacting
concrete is a fluid mixture suitable for placing in structures with
congested reinforcement without vibration. Self-compacting concrete
development must ensure a good balance between deformability and
stability. Also, compatibility is affected by the characteristics of
materials and the mix proportions; it becomes necessary to evolve a
procedure for mix design of SCC.
This paper presents an experimental procedure for the design of
self-compacting concrete mixes with different water-cement ratios
(w/c) and other constant ratios by local materials. The test results for
acceptance characteristics of self-compacting concrete such as slump
flow, V-funnel and L-Box are presented. Further, compressive
strength, tensile strength and modulus of elasticity of specimens were
also determined and results are included here
Abstract: Heterogeneous catalysis is vital for a number of
chemical, refinery and pollution control processes. The use of
catalyst pellets of hollow cylindrical shape provide several distinct
advantages over other common shapes, and can therefore help to
enhance conversion levels in reactors. A better utilization of the
catalytic material is probably most notable of these features due to
the absence of the pellet core, which helps to significantly lower the
effect of the internal transport resistance. This is reflected in the
enhancement of the effectiveness factor. For the case of the first order
irreversible kinetics, a substantial increase in the effectiveness factor
can be obtained by varying shape parameters. Important shape
parameters of a finite hollow cylinder are the ratio of the inside to the
outside radii (κ) and the height to the diameter ratio (γ). A high value
of κ the generally helps to enhance the effectiveness factor. On the
other hand, lower values of the effectiveness factors are obtained
when the dimension of the height and the diameter are comparable.
Thus, the departure of parameter γ from the unity favors higher
effectiveness factor. Since a higher effectiveness factor is a measure
of a greater utilization of the catalytic material, higher conversion
levels can be achieved using the hollow cylindrical pellets possessing
optimized shape parameters.
Abstract: Renewable natural fibres such as oil palm, flax, and
pineapple leaf can be utilized to obtain new high performance
polymer materials. The reuse of waste natural fibres as reinforcement
for polymer is a sustainable option to the environment. However, due
to its high hydroxyl content of cellulose, natural fibres are
susceptible to absorb water that affects the composite mechanical
properties adversely. Research found that Nano materials such as
Nano Silica Carbide (n-SiC) and Nano Clay can be added into the
polymer composite to overcome this problem by enhancing its
mechanical properties in wet condition. The addition of Nano
material improves the tensile and wear properties, flexural stressstrain
behaviour, fracture toughness, and fracture strength of polymer
natural composites in wet and dry conditions.
Abstract: In this work the design and characterization of an optoelectronic automated measurement system it is presented. The optoelectronic devices of this system are an optical transmitter, the optical components and the optical receiver, which were selected for a great precision of the system. The mechanical system allows free displacement of the components as well as the devices that generate the movement. The results, length and profile of the objects are display in Lab View.
Abstract: This paper reviews the optimization available
transmission capability (ATC) of power systems using a device of
FACTS named SSSC equipped with energy storage devices. So that,
emplacement and improvement of parameters of SSSC will be
illustrated. Thus, voltage magnitude constraints of network buses,
line transient stability constraints and voltage breakdown constraints
are considered. To help the calculations, a comprehensive program in
DELPHI is provided, which is able to simulate and trace the
parameters of SSSC has been installed on a specific line.
Furthermore, the provided program is able to compute ATC, TTC
and maximum value of their enhancement after using SSSC.
Abstract: The main objective of this paper is a comparative
investigate in enhancement of damping power system oscillation via
coordinated design of the power system stabilizer (PSS) and static
synchronous series compensator (SSSC) and static synchronous
compensator (STATCOM). The design problem of FACTS-based
stabilizers is formulated as a GA based optimization problem. In this
paper eigenvalue analysis method is used on small signal stability of
single machine infinite bus (SMIB) system installed with SSSC and
STATCOM. The generator is equipped with a PSS. The proposed
stabilizers are tested on a weakly connected power system with
different disturbances and loading conditions. This aim is to enhance
both rotor angle and power system stability. The eigenvalue analysis
and non-linear simulation results are presented to show the effects of
these FACTS-based stabilizers and reveal that SSSC exhibits the best
effectiveness on damping power system oscillation.
Abstract: One of the main challenges for one phase anaerobic digestion processes is the high concentration of NH4+ and PO4 3- ions
in the digested sludge supernatant. This project focuses on enhancing the removal of nutrients during the anaerobic digestion process through fixing both NH4+ and PO4 3- ions in the form of struvite (magnesium ammonium phosphate, MAP, MgNH4PO4.6H2O) within the anaerobic sludge. Batch anaerobic digestion tests showed that Mg2+ concentration in the range 279 – 812 mg/L had insignificant effect on CGP but incurred a slight increase in COD removal. The reactor that had soluble Mg2+:NH4+:PO43- at a molar ratio of 1.28:1:00:1:00 achieved the best performance enhancement of 8% increase in COD removal and 32% reduction in NH4+ in the reactor supernatant. Overall, the results show that there is a potential to optimise conventional anaerobic digestion such that supernatant lean in P and N, and sludge rich in nutrients are obtained.
Abstract: Optimal capacitor allocation in distribution systems
has been studied for a long times. It is an optimization problem
which has an objective to define the optimal sizes and locations of
capacitors to be installed. In this works, an overview of capacitor
placement problem in distribution systems is briefly introduced. The
objective functions and constraints of the problem are listed and the
methodologies for solving the problem are summarized.
Abstract: The Influence Diagrams (IDs) is a kind of Probabilistic Belief Networks for graphic modeling. The usage of IDs can improve the communication among field experts, modelers, and decision makers, by showing the issue frame discussed from a high-level point of view. This paper enhances the Time-Sliced Influence Diagrams (TSIDs, or called Dynamic IDs) based formalism from a Discrete Event Systems Modeling and Simulation (DES M&S) perspective, for Exploring Analysis (EA) modeling. The enhancements enable a modeler to specify times occurred of endogenous events dynamically with stochastic sampling as model running and to describe the inter- influences among them with variable nodes in a dynamic situation that the existing TSIDs fails to capture. The new class of model is named Dynamic-Stochastic Influence Diagrams (DSIDs). The paper includes a description of the modeling formalism and the hiberarchy simulators implementing its simulation algorithm, and shows a case study to illustrate its enhancements.
Abstract: When acid is pumped into damaged reservoirs for
damage removal/stimulation, distorted inflow of acid into the
formation occurs caused by acid preferentially traveling into highly
permeable regions over low permeable regions, or (in general) into
the path of least resistance. This can lead to poor zonal coverage and
hence warrants diversion to carry out an effective placement of acid.
Diversion is desirably a reversible technique of temporarily reducing
the permeability of high perm zones, thereby forcing the acid into
lower perm zones.
The uniqueness of each reservoir can pose several challenges to
engineers attempting to devise optimum and effective diversion
strategies. Diversion techniques include mechanical placement and/or
chemical diversion of treatment fluids, further sub-classified into ball
sealers, bridge plugs, packers, particulate diverters, viscous gels,
crosslinked gels, relative permeability modifiers (RPMs), foams,
and/or the use of placement techniques, such as coiled tubing (CT)
and the maximum pressure difference and injection rate (MAPDIR)
methodology.
It is not always realized that the effectiveness of diverters greatly
depends on reservoir properties, such as formation type, temperature,
reservoir permeability, heterogeneity, and physical well
characteristics (e.g., completion type, well deviation, length of
treatment interval, multiple intervals, etc.). This paper reviews the
mechanisms by which each variety of diverter functions and
discusses the effect of various reservoir properties on the efficiency
of diversion techniques. Guidelines are recommended to help
enhance productivity from zones of interest by choosing the best
methods of diversion while pumping an optimized amount of
treatment fluid. The success of an overall acid treatment often
depends on the effectiveness of the diverting agents.
Abstract: This paper presents a new STAKCERT KDD
processes for worm detection. The enhancement introduced in the
data-preprocessing resulted in the formation of a new STAKCERT
model for worm detection. In this paper we explained in detail how
all the processes involved in the STAKCERT KDD processes are
applied within the STAKCERT model for worm detection. Based on
the experiment conducted, the STAKCERT model yielded a 98.13%
accuracy rate for worm detection by integrating the STAKCERT
KDD processes.
Abstract: X-ray mammography is the most effective method for
the early detection of breast diseases. However, the typical diagnostic
signs such as microcalcifications and masses are difficult to detect
because mammograms are of low-contrast and noisy. In this paper, a
new algorithm for image denoising and enhancement in Orthogonal
Polynomials Transformation (OPT) is proposed for radiologists to
screen mammograms. In this method, a set of OPT edge coefficients
are scaled to a new set by a scale factor called OPT scale factor. The
new set of coefficients is then inverse transformed resulting in
contrast improved image. Applications of the proposed method to
mammograms with subtle lesions are shown. To validate the
effectiveness of the proposed method, we compare the results to
those obtained by the Histogram Equalization (HE) and the Unsharp
Masking (UM) methods. Our preliminary results strongly suggest
that the proposed method offers considerably improved enhancement
capability over the HE and UM methods.
Abstract: With respect to the dissipation of energy through
plastic deformation of joints of prefabricated wall units, the paper
points out the principal importance of efficient reinforcement of the
prefabricated system at its joints. The method, quality and amount of
reinforcement are essential for reaching the necessary degree of joint
ductility. The paper presents partial results of experimental research
of vertical joints of prefabricated units exposed to monotonously
rising loading and repetitive shear force and formulates a conclusion
that the limit state of the structure as a whole is preceded by the
disintegration of joints, or that the structure tends to pass from
linearly elastic behaviour to non-linearly elastic to plastic behaviour
by exceeding the proportional elastic limit in joints.Experimental
verification on a model of a 7-storey prefabricated structure revealed
weak points in its load-bearing systems, mainly at places of critical
points around openings situated in close proximity to vertical joints
of mutually perpendicularly oriented walls.
Abstract: Early detection of lung cancer through chest radiography is a widely used method due to its relatively affordable cost. In this paper, an approach to improve lung nodule visualization on chest radiographs is presented. The approach makes use of linear phase high-frequency emphasis filter for digital filtering and
histogram equalization for contrast enhancement to achieve improvements. Results obtained indicate that a filtered image can
reveal sharper edges and provide more details. Also, contrast enhancement offers a way to further enhance the global (or local) visualization by equalizing the histogram of the pixel values within
the whole image (or a region of interest). The work aims to improve lung nodule visualization of chest radiographs to aid detection of lung cancer which is currently the leading cause of cancer deaths worldwide.
Abstract: Total liquid ventilation can support gas exchange in animal models of lung injury. Clinical application awaits further technical improvements and performance verification. Our aim was to develop a liquid ventilator, able to deliver accurate tidal volumes, and a computerized system for measuring lung mechanics. The computer-assisted, piston-driven respirator controlled ventilatory parameters that were displayed and modified on a real-time basis. Pressure and temperature transducers along with a lineal displacement controller provided the necessary signals to calculate lung mechanics. Ten newborn lambs (
Abstract: In recent years, sustainable supply chain management
(SSCM) has been widely researched in academic domain. However,
due to the traditional operational role and the complexity of supply
chain management in the cement industry, a relatively small amount
of research has been conducted on cement supply chain simulation
integrated with sustainability criteria. This paper analyses the cement
supply chain operations using the Push-Pull supply chain
frameworks, the Life Cycle Assessment (LCA) methodology; and
proposal integration approach, proposes three supply chain scenarios
based on Make-To-Stock (MTS), Pack-To-Order (PTO) and Grind-
To-Order (GTO) strategies. A Discrete-Event Simulation (DES)
model of SSCM is constructed using Arena software to implement
the three-target scenarios. We conclude with the simulation results
that (GTO) is the optimal supply chain strategy that demonstrates the
best economic, ecological and social performance in the cement
industry.
Abstract: This paper presents a new technique for the optimum
placement of processors to minimize the total effective
communication load under multi-processor communication
dominated environment. This is achieved by placing heavily loaded
processors near each other and lightly loaded ones far away from
one another in the physical grid locations. The results are
mathematically proved for the Algorithms are described.