Abstract: This paper presents the development of analysis tools
for Home Agriculture project. The tools are required for monitoring
the condition of greenhouse which involves two components:
measurement hardware and data analysis engine. Measurement
hardware is functioned to measure environment parameters such as
temperature, humidity, air quality, dust and etc while analysis tool is
used to analyse and interpret the integrated data against the condition
of weather, quality of health, irradiance, quality of soil and etc. The
current development of the tools is completed for off-line data
recorded technique. The data is saved in MMC and transferred via
ZigBee to Environment Data Manager (EDM) for data analysis.
EDM converts the raw data and plot three combination graphs. It has
been applied in monitoring three months data measurement for
irradiance, temperature and humidity of the greenhouse..
Abstract: This paper describes the development of a control
system model using a graphical software tool. This control system is
part of an operator training simulator developed for the National
Training Center for Operators of Ixtapantongo (CNCAOI, acronym
according to its name in Spanish language) of the Mexico-s Federal
Commission of Electricity, CFE). The Department of Simulation of
the Electrical Research Institute (IIE) developed this simulator using
as reference the Unit I of the Combined Cycle Power Plant El Sauz,
located at the centre of Mexico. The first step in the project was the
developing of the Gas Turbine System and its control system
simulator. The Turbo Gas simulator was finished and delivered to
CNCAOI in March 2007 for commercial operation. This simulator is
a high-fidelity real time dynamic simulator built and tested for
accurate operation over the entire load range. The simulator was used
primarily for operator training although it has been used for
procedure development and evaluation of plant transients.
Abstract: Previously, harmonic parameters (HPs) have been
selected as features extracted from EEG signals for automatic sleep
scoring. However, in previous studies, only one HP parameter was
used, which were directly extracted from the whole epoch of EEG
signal.
In this study, two different transformations were applied to extract
HPs from EEG signals: Hilbert-Huang transform (HHT) and wavelet
transform (WT). EEG signals are decomposed by the two
transformations; and features were extracted from different
components. Twelve parameters (four sets of HPs) were extracted.
Some of the parameters are highly diverse among different stages.
Afterward, HPs from two transformations were used to building a
rough sleep stages scoring model using the classifier SVM. The
performance of this model is about 78% using the features obtained by
our proposed extractions. Our results suggest that these features may
be useful for automatic sleep stages scoring.
Abstract: This paper presented a new approach for centralized
monitoring and self-protected against fiber fault in fiber-to-the-home
(FTTH) access network by using Smart Access Network Testing,
Analyzing and Database (SANTAD). SANTAD will be installed
with optical line terminal (OLT) at central office (CO) for in-service
transmission surveillance and fiber fault localization within FTTH
with point-to-multipoint (P2MP) configuration downwardly from CO
towards customer residential locations based on the graphical user
interface (GUI) processing capabilities of MATLAB software.
SANTAD is able to detect any fiber fault as well as identify the
failure location in the network system. SANTAD enable the status of
each optical network unit (ONU) connected line is displayed onto
one screen with capability to configure the attenuation and detect the
failure simultaneously. The analysis results and information will be
delivered to the field engineer for promptly actions, meanwhile the
failure line will be diverted to protection line to ensure the traffic
flow continuously. This approach has a bright prospect to improve
the survivability and reliability as well as increase the efficiency and
monitoring capabilities in FTTH.
Abstract: Ligula intestinalis is a three-host life-cycle
Pseudophyllidean Cestode which in its plerocercoid stage infests a
range of fresh water species. The objective of the present study was
the worm occurrence within planctonic copepods, fishes and
piscivorous birds and examine of parasite-hosts samples in the Lake
of Sattarkhan Dam (near the city of Ahar, East Azerbaijan, Iran).
Fish sample were collected with fyke and gill nets and the abdominal
cavity was examined for the presence of ligula. Zooplanktons were
captured using a planktonic net and occurrence of parasitic larval
form in the body cavity was determined. Piscivorous birds were
selected by telescope, they hunted and dissected for presence of
parasite eggs in their gut. Results indicated that prevalence of
infection was 16% for cyclopid copepoda and majority of infected
cyclopid were female Cyclops. Investigation of 310 fishes specimens
were indicated to infection of five species of cyprinid fishes. In
addition, results indicated to manipulation of six species of migratory
aquatic and semi aquatic birds by ligula. Obtained results are in
agreement by previous studies. Its definite in this study that all of
fishes in Sattarkhan Lake capable to infection, its important for
health because they capture by native people and it is documented
that ligula can be introduce as a zoonose. It's seemed that to prevent
from disperses of parasite and restricted of infection, biological
elimination can be effective and it's necessary to inform native
people about sanitation.
Abstract: Most of the commonly used blind equalization algorithms are based on the minimization of a nonconvex and nonlinear cost function and a neural network gives smaller residual error as compared to a linear structure. The efficacy of complex valued feedforward neural networks for blind equalization of linear and nonlinear communication channels has been confirmed by many studies. In this paper we present two neural network models for blind equalization of time-varying channels, for M-ary QAM and PSK signals. The complex valued activation functions, suitable for these signal constellations in time-varying environment, are introduced and the learning algorithms based on the CMA cost function are derived. The improved performance of the proposed models is confirmed through computer simulations.
Abstract: A mathematical model for the hydrodynamic
lubrication of parabolic slider bearings with couple stress lubricants
is presented. A numerical solution for the mathematical model using
finite element scheme is obtained using three nodes isoparametric
quadratic elements. Stiffness integrals obtained from the weak form
of the governing equations were solved using Gauss Quadrature to
obtain a finite number of stiffness matrices. The global system of
equations was obtained for the bearing and solved using Gauss Seidel
iterative scheme. The converged pressure solution was used to obtain
the load capacity of the bearing. Parametric studies were carried out
and it was shown that the effect of couple stresses and profile
parameter are to increase the load carrying capacity of the parabolic
slider bearing. Numerical experiments reveal that the magnitude of
the profile parameter at which maximum load is obtained increases
with decrease in couple stress parameter. The results are presented in
graphical form.
Abstract: The beneficial effects of Si are mainly associated with
its high deposition in plant tissue and enhancing their strength and
rigidity. We investigated the role of Si against cadmium stress in
(Echium C) in house green condition. When the seventh leaves was
be appeared, plants were pretreated with five levels of Si: 0, 0.2, 0.5,
0.7and 1.5 mM Si (as sodium trisilicate, Na2(SiO2)3) and after that
plants were treated with two levels of Cd (30 and 90 mM). The
effects of Silicon and Cd were investigated on some physiological
and biochemical parameters such as: lipid peroxidation
(malondialdehyde (MDA) and other aldehydes, antocyanin and
flavonoid content. Our results showed that Cd significantly increased
MDA, other aldehydes, antocyanin and flavonoids content in
Echium and silicon offset the negative effect and increased tolerance
of Echium against Cd stress. From this results we concluded that Si
increase membrane integrity and antioxidative ability in this plant
against cd stress.
Abstract: This paper proposes a methodology for mitigating the occurrence of cascading failure in stressed power systems. The methodology is essentially based on predicting voltage instability in the power system using a voltage stability index and then devising a corrective action in order to increase the voltage stability margin. The paper starts with a brief description of the cascading failure mechanism which is probable root cause of severe blackouts. Then, the voltage instability indices are introduced in order to evaluate stability limit. The aim of the analysis is to assure that the coordination of protection, by adopting load shedding scheme, capable of enhancing performance of the system after the major location of instability is determined. Finally, the proposed method to generate instability prediction is introduced.
Abstract: Noise has adverse effect on human health and
comfort. Noise not only cause hearing impairment, but it also acts as
a causal factor for stress and raising systolic pressure. Additionally it
can be a causal factor in work accidents, both by marking hazards
and warning signals and by impeding concentration. Industry
workers also suffer psychological and physical stress as well as
hearing loss due to industrial noise. This paper proposes an approach
to enable engineers to point out quantitatively the noisiest source for
modification, while multiple machines are operating simultaneously.
The model with the point source and spherical radiation in a free field
was adopted to formulate the problem. The procedure works very
well in ideal cases (point source and free field). However, most of the
industrial noise problems are complicated by the fact that the noise is
confined in a room. Reflections from the walls, floor, ceiling, and
equipment in a room create a reverberant sound field that alters the
sound wave characteristics from those for the free field. So the model
was validated for relatively low absorption room at NIT Kurukshetra
Central Workshop. The results of validation pointed out that the
estimated sound power of noise sources under simultaneous
conditions were on lower side, within the error limits 3.56 - 6.35 %.
Thus suggesting the use of this methodology for practical
implementation in industry. To demonstrate the application of the
above analytical procedure for estimating the sound power of noise
sources under simultaneous operating conditions, a manufacturing
facility (Railway Workshop at Yamunanagar, India) having five
sound sources (machines) on its workshop floor is considered in this
study. The findings of the case study had identified the two most
effective candidates (noise sources) for noise control in the Railway
Workshop Yamunanagar, India. The study suggests that the
modification in the design and/or replacement of these two identified
noisiest sources (machine) would be necessary so as to achieve an
effective reduction in noise levels. Further, the estimated data allows
engineers to better understand the noise situations of the workplace
and to revise the map when changes occur in noise level due to a
workplace re-layout.
Abstract: Wavelet transform has been extensively used in
machine fault diagnosis and prognosis owing to its strength to deal
with non-stationary signals. The existing Wavelet transform based
schemes for fault diagnosis employ wavelet decomposition of the
entire vibration frequency which not only involve huge
computational overhead in extracting the features but also increases
the dimensionality of the feature vector. This increase in the
dimensionality has the tendency to 'over-fit' the training data and
could mislead the fault diagnostic model. In this paper a novel
technique, envelope wavelet packet transform (EWPT) is proposed in
which features are extracted based on wavelet packet transform of the
filtered envelope signal rather than the overall vibration signal. It not
only reduces the computational overhead in terms of reduced number
of wavelet decomposition levels and features but also improves the
fault detection accuracy. Analytical expressions are provided for the
optimal frequency resolution and decomposition level selection in
EWPT. Experimental results with both actual and simulated machine
fault data demonstrate significant gain in fault detection ability by
EWPT at reduced complexity compared to existing techniques.
Abstract: Natural gas is defined as gas obtained from a natural underground reservoir. It generally contains a large quantity of methane along with heavier hydrocarbons such as ethane, propane, isobutene, normal butane; also in the raw state it often contains a considerable amount of non hydrocarbons, such as nitrogen and the acid gases (carbon dioxide and hydrogen sulfide). The acid gases must be removed from natural gas before use. One of the processes witch are use in the industry to remove the acid gases from natural gas is the use of alkanolamine process. In this present paper, a simulation study for an industrial gas sweetening plant has been investigated. The aim of the study is to investigate the effect of using mixing amines as solvent on the gas treatment process using the software Hysys.
Abstract: Can biometrics do what everyone is expecting it will?
And more importantly, should it be doing it? Biometrics is the
buzzword “on the mouth" of everyone, who are trying to use this
technology in a variety of applications. But all this “hype" about
biometrics can be dangerous without a careful evaluation of the real
needs of each application. In this paper I-ll try to focus on the
dangers of using the right technology at the right time in the wrong
place.
Abstract: The motivation of this work was to find a suitable 3D
scanner for human body parts digitalization in the field of prosthetics
and orthotics. The main project objective is to compare the three
hand-held portable scanners (two optical and one laser) and two
optical tripod scanners. The comparison was made with respect of
scanning detail, simplicity of operation and ability to scan directly on
the human body. Testing was carried out on a plaster cast of the
upper limb and directly on a few volunteers. The objective monitored
parameters were time of digitizing and post-processing of 3D data
and resulting visual data quality. Subjectively, it was considered level
of usage and handling of the scanner. The new tripod was developed
to improve the face scanning conditions. The results provide an
overview of the suitability of different types of scanners.
Abstract: Power consumption is rapidly increased in data centers
because the number of data center is increased and more the scale of
data center become larger. Therefore, it is one of key research items to
reduce power consumption in data center. The peak power of a typical
server is around 250 watts. When a server is idle, it continues to use
around 60% of the power consumed when in use, though vendors are
putting effort into reducing this “idle" power load. Servers tend to
work at only around a 5% to 20% utilization rate, partly because of
response time concerns. An average of 10% of servers in their data
centers was unused. In those reason, we propose dynamic power
management system to reduce power consumption in green data
center. Experiment result shows that about 55% power consumption is
reduced at idle time.
Abstract: Activity-Based Costing (ABC) represents an
alternative paradigm to traditional cost accounting system and
it often provides more accurate cost information for decision
making such as product pricing, product mix, and make-orbuy
decisions. ABC models the causal relationships between
products and the resources used in their production and traces
the cost of products according to the activities through the use
of appropriate cost drivers. In this paper, the implementation
of the ABC in a manufacturing system is analyzed and a
comparison with the traditional cost based system in terms of
the effects on the product costs are carried out to highlight the
difference between two costing methodologies. By using this
methodology, a valuable insight into the factors that cause the
cost is provided, helping to better manage the activities of the
company.
Abstract: Brick is one of the most common masonry units used as building material. Due to the demand, different types of waste have been investigated to be incorporated into the bricks. Many types of sludge have been incorporated in fired clay brick for example marble sludge, stone sludge, water sludge, sewage sludge, and ceramic sludge. The utilization of these waste materials in fired clay bricks usually has positive effects on the properties such as lightweight bricks with improved shrinkage, porosity, and strength. This paper reviews on utilization of different types of sludge wastes into fired clay bricks. Previous investigations have demonstrated positive effects on the physical and mechanical properties as well as less impact towards the environment. Thus, the utilizations of sludge waste could produce a good quality of brick and could be one of alternative disposal methods for the sludge wastes.
Abstract: A sequential treatment of ozonation followed by a
Fenton or photo-Fenton process, using black light lamps (365 nm) in
this latter case, has been applied to remove a mixture of
pharmaceutical compounds and the generated by-products both in
ultrapure and secondary treated wastewater. The scientifictechnological
innovation of this study stems from the in situ
generation of hydrogen peroxide from the direct ozonation of
pharmaceuticals, and can later be used in the application of Fenton
and photo-Fenton processes. The compounds selected as models
were sulfamethoxazol and acetaminophen. It should be remarked that
the use of a second process is necessary as a result of the low
mineralization yield reached by the exclusive application of ozone.
Therefore, the influence of the water matrix has been studied in terms
of hydrogen peroxide concentration, individual compound
concentration and total organic carbon removed. Moreover, the
concentration of different iron species in solution has been measured.
Abstract: Automatic Extraction of Event information from
social text stream (emails, social network sites, blogs etc) is a vital
requirement for many applications like Event Planning and
Management systems and security applications. The key information
components needed from Event related text are Event title, location,
participants, date and time. Emails have very unique distinctions over
other social text streams from the perspective of layout and format
and conversation style and are the most commonly used
communication channel for broadcasting and planning events.
Therefore we have chosen emails as our dataset. In our work, we
have employed two statistical NLP methods, named as Finite State
Machines (FSM) and Hidden Markov Model (HMM) for the
extraction of event related contextual information. An application
has been developed providing a comparison among the two methods
over the event extraction task. It comprises of two modules, one for
each method, and works for both bulk as well as direct user input.
The results are evaluated using Precision, Recall and F-Score.
Experiments show that both methods produce high performance and
accuracy, however HMM was good enough over Title extraction and
FSM proved to be better for Venue, Date, and time.
Abstract: Interactive push VOD system is a new kind of system
that incorporates push technology and interactive technique. It can
push movies to users at high speeds at off-peak hours for optimal
network usage so as to save bandwidth. This paper presents effective
software-based solution for processing mass downstream data at
terminals of interactive push VOD system, where the service can
download movie according to a viewer-s selection. The downstream
data is divided into two catalogs: (1) the carousel data delivered
according to DSM-CC protocol; (2) IP data delivered according to
Euro-DOCSIS protocol. In order to accelerate download speed and
reduce data loss rate at terminals, this software strategy introduces
caching, multi-thread and resuming mechanisms. The experiments
demonstrate advantages of the software-based solution.