Abstract: In this study arsenate [As(V)] removal from drinking water by coagulation process was investigated. Ferric chloride (FeCl3.6H2O) and ferrous sulfate (FeSO4.7H2O) were used as coagulant. The effects of major operating variables such as coagulant dose (1–30 mg/L) and pH (5.5–9.5) were investigated. Ferric chloride and ferrous sulfate were found as effective and reliable coagulant due to required dose, residual arsenate and coagulant concentration. Optimum pH values for maximum arsenate removal for ferrous sulfate and ferric chloride were found as 8 and 7.5. The arsenate removal efficiency decreased at neutral and acidic pH values for Fe(II) and at the high acidic and high alkaline pH for Fe(III). It was found that the increase of coagulant dose caused a substantial increase in the arsenate removal. But above a certain ferric chloride and ferrous sulfate dosage, the increase in arsenate removal was not significant. Ferric chloride and ferrous sulfate dose above 8 mg/L slightly increased arsenate removal.
Abstract: We report the electronic structure and optical
properties of NdF3 compound. Our calculations are based on density
functional theory (DFT) using the full potential linearized augmented
plane wave (FPLAPW) method with the inclusion of spin orbit
coupling. We employed the local spin density approximation (LSDA)
and Coulomb-corrected local spin density approximation, known for
treating the highly correlated 4f electrons properly, is able to
reproduce the correct insulating ground state. We find that the
standard LSDA approach is incapable of correctly describing the
electronic properties of such materials since it positions the f-bands
incorrectly resulting in an incorrect metallic ground state. On the
other hand, LSDA + U approximation, known for treating the highly
correlated 4f electrons properly, is able to reproduce the correct
insulating ground state. Interestingly, however, we do not find any
significant differences in the optical properties calculated using
LSDA, and LSDA + U suggesting that the 4f electrons do not play a
decisive role in the optical properties of these compounds. The
reflectivity for NdF3 compound stays low till 7 eV which is
consistent with their large energy gaps. The calculated energy gaps
are in good agreement with experiments. Our calculated reflectivity
compares well with the experimental data and the results are analyzed
in the light of band to band transitions.
Abstract: For controlling urban transportations, traffic lights
show similar behavior for different kinds of vehicles at intersections.
Emergency vehicles need special behavior at intersections, so traffic
lights should behave in different manner when emergency vehicles
approach them. At the present time, intelligent traffic lights control
urban transportations intelligently. In this paper the ethical aspect of
this topic is considered. A model is proposed for adding special
component to emergency vehicles and traffic lights for controlling
traffic in ethical manner. The proposed model is simulated by JADE.
Abstract: For Romania, the fulfilment of the obligations
undertaken as a member state of the European Union in accordance
with the Treaty of Accession requires the effective implementation of
sustainable development principles and practices, this being the only
reasonable development option, which adequately draws in on the
economic, social and environment resources. Achieving this
objective is based on a profound analysis of the realities in the
Romanian economy, which will reflect the existent situation and the
action directions for the future. The paper presents an analysis of the
Romanian economic performances compared to the EU economy,
based on the sustainable value (SV) model. The analysis highlighted
the considerable gap between Romania and the EU regarding the
sustainable capitalization of resources, the provided information
being useful to justify strategic development decisions at a micro and
macro levels.
Abstract: The 20th century has brought much development to the practice of Architecture worldwide, and technology has bridged inhabitation limits in many regions of the world with high levels of comfort and conveniences, most times at high costs to the environment. Throughout the globe, the tropical countries are being urbanized at an unprecedented rate and housing has become a major issue worldwide, in light of increased demand and lack of appropriate infra-structure and planning. Buildings and urban spaces designed in tropical cities have mainly adopted external concepts that in most cases do not fit the needs of the inhabitants living in such harsh climatic environment, and when they do, do so at high financial, environmental and cultural costs. Traditional architectural practices can provide valuable understanding on how self-reliance and autonomy of construction can be reinforced in rural-urban tropical environments. From traditional housing knowledge, it is possible to derive lessons for the development of new construction materials that are affordable, environmentally friendly, culturally acceptable and accesible to all.Specifically to the urban context, such solutions are of outmost importance, given the needs to a more democratic society, where access to housing is considered high in the agenda for development. Traditional or rural constructions are also ongoing through extensive changes eventhough they have mostly adopted climate-responsive building practices relying on local resources (with minimum embodied energy) and energy (for comfort and quality of life). It is important to note that many of these buildings can actually be called zero-energy, and hold potential answers to enable transition from high energy, high cost, low comfort urban habitations to zero/low energy habitations with high quality urban livelihood. Increasing access to modern urban lifestyels have also an effect on the aspirations from people in terms of performance, comfort and convenience in terms of their housing and the way it is produced and used. These aspirations are resulting in transitions from localresource dependent habitations- to non-local resource based highenergy urban style habitations. And such transitions are resulting in the habitations becoming increasingly unsuited to the local climatic conditions with increasing discomfort, ill-health, and increased CO2 emissions and local environmental disruption. This research studies one specific transition group in the context of 'water communities' in tropical-equatorial regions: Ribeirinhos housing typology (Amazonas, Brazil). The paper presents the results of a qualitative sustainability assessment of the housing typologies under transition, found at the Ribeirinhos communities.
Abstract: Nanostructured materials have attracted many
researchers due to their outstanding mechanical and physical
properties. For example, carbon nanotubes (CNTs) or carbon
nanofibres (CNFs) are considered to be attractive reinforcement
materials for light weight and high strength metal matrix composites.
These composites are being projected for use in structural
applications for their high specific strength as well as functional
materials for their exciting thermal and electrical characteristics. The
critical issues of CNT-reinforced MMCs include processing
techniques, nanotube dispersion, interface, strengthening mechanisms
and mechanical properties. One of the major obstacles to the effective
use of carbon nanotubes as reinforcements in metal matrix
composites is their agglomeration and poor distribution/dispersion
within the metallic matrix. In order to tap into the advantages of the
properties of CNTs (or CNFs) in composites, the high dispersion of
CNTs (or CNFs) and strong interfacial bonding are the key issues
which are still challenging. Processing techniques used for synthesis
of the composites have been studied with an objective to achieve
homogeneous distribution of carbon nanotubes in the matrix.
Modified mechanical alloying (ball milling) techniques have emerged
as promising routes for the fabrication of carbon nanotube (CNT)
reinforced metal matrix composites. In order to obtain a
homogeneous product, good control of the milling process, in
particular control of the ball movement, is essential. The control of
the ball motion during the milling leads to a reduction in grinding
energy and a more homogeneous product. Also, the critical inner
diameter of the milling container at a particular rotational speed can
be calculated. In the present work, we use conventional and modified
mechanical alloying to generate a homogenous distribution of 2 wt.
% CNT within Al powders. 99% purity Aluminium powder (Acros,
200mesh) was used along with two different types of multiwall
carbon nanotube (MWCNTs) having different aspect ratios to
produce Al-CNT composites. The composite powders were processed
into bulk material by compaction, and sintering using a cylindrical
compaction and tube furnace. Field Emission Scanning electron
microscopy (FESEM), X-Ray diffraction (XRD), Raman
spectroscopy and Vickers macro hardness tester were used to
evaluate CNT dispersion, powder morphology, CNT damage, phase
analysis, mechanical properties and crystal size determination.
Despite the success of ball milling in dispersing CNTs in Al powder,
it is often accompanied with considerable strain hardening of the Al
powder, which may have implications on the final properties of the
composite. The results show that particle size and morphology vary
with milling time. Also, by using the mixing process and sonication
before mechanical alloying and modified ball mill, dispersion of the
CNTs in Al matrix improves.
Abstract: This work focuses on the remediation of polycyclic
aromatic hydrocarbons (PAHs)-contaminated soil via Fenton
treatment coupled with novel chelating agent (CA). The feasibility of
chelated modified Fenton (MF) treatment to promote PAH oxidation
in artificially contaminated soils was investigated in laboratory scale
batch experiments at natural pH. The effects of adding inorganic and
organic CA are discussed. Experiments using different iron catalyst
to CA ratios were conducted, resulting in hydrogen peroxide: soil:
iron: CA weight ratios that varied from 0.049: 1: 0.072: 0.008 to
0.049: 1: 0.072: 0.067. The results revealed that (1) inorganic CA
could provide much higher PAH removal efficiency and (2) most of
the proposed CAs were more efficient than commonly utilised CAs
even at mild ratio. This work highlights the potential of novel
chelating agents in maintaining a suitable environment throughout
the Fenton treatment, particularly in soils with high buffer capacity.
Abstract: Public parks are placed high on the research agenda, with many studies addressing their social, economic and environment influences in different countries around the world. They have been recognized as contributors to the physical quality of urban environments. Recently, a broader view of public parks has emerged. This view goes well beyond the traditional value of parks as places for more recreation and visual delight, to depict them as valuable contributors to broader strategic objectives, such as property values, place attractiveness, job opportunities, social belonging, public health, tourist development, and improving the overall quality of life. This research examines the role of public parks in enhancing the quality of human life in Egyptian environment. It measures 'quality of life' in terms of 'human needs' and 'well-being'. This should open ways for policymakers, practitioners, researchers and the public to realize the potentials of public parks towards improving the quality of life.
Abstract: To simulate expected climate change, we implemented a two-factor (temperature and soil moisture) field design in a forest in Ontario, Canada. To manipulate moisture input, we erected rain-exclusion structures. Under each structure, plots were watered with one of three treatments and thermally controlled with three heat treatments to simulate changes in air temperature and rainfall based on the climate model (GCM) predictions for the study area. Environmental conditions (including untreated controls) were monitored tracking air temperature, soil temperature, soil moisture, and photosynthetically active radiation. We measured rainfall and relative humidity at the site outside the rain-exclusion structures. Analyses of environmental conditions demonstrates that the temperature manipulation was most effective at maintaining target temperature during the early part of the growing season, but it was more difficult to keep the warmest treatment at 5º C above ambient by late summer. Target moisture regimes were generally achieved however incoming solar radiation was slightly attenuated by the structures.
Abstract: There are three main ways of categorizing capital in banking operations: accounting, regulatory and economic capital. However, the 2008-2009 global crisis has shown that none of these categories adequately reflects the real risks of bank operations, especially in light of the failures Bear Stearns, Lehman Brothers or Northern Rock. This paper deals with the economic capital allocation of global banks. In theory, economic capital should reflect the real risks of a bank and should be publicly available. Yet, as discovered during the global financial crisis, even when economic capital information was publicly disclosed, the underlying assumptions rendered the information useless. Specifically, some global banks that reported relatively high levels of economic capital before the crisis went bankrupt or had to be bailed-out by their government. And, only 15 out of 50 global banks reported their economic capital during the 2007-2010 period. In this paper, we analyze the changes in reported bank economic capital disclosure during this period. We conclude that relative shares of credit and business risks increased in 2010 compared to 2007, while both operational and market risks decreased their shares on the total economic capital of top-rated global banks. Generally speaking, higher levels of disclosure and transparency of bank operations are required to obtain more confidence from stakeholders. Moreover, additional risks such as liquidity risks should be included in these disclosures.
Abstract: Existing image-based virtual reality applications
allow users to view image-based 3D virtual environment in a more
interactive manner. User could “walkthrough"; looks left, right, up
and down and even zoom into objects in these virtual worlds of
images. However what the user sees during a “zoom in" is just a
close-up view of the same image which was taken from a distant.
Thus, this does not give the user an accurate view of the object from
the actual distance. In this paper, a simple technique for zooming in
an object in a virtual scene is presented. The technique is based on
the 'hotspot' concept in existing application. Instead of navigation
between two different locations, the hotspots are used to focus into
an object in the scene. For each object, several hotspots are created.
A different picture is taken for each hotspot. Each consecutive
hotspot created will take the user closer to the object. This will
provide the user with a correct of view of the object based on his
proximity to the object. Implementation issues and the relevance of
this technique in potential application areas are highlighted.
Abstract: A network of coupled stochastic oscillators is
proposed for modeling of a cluster of entangled qubits that is
exploited as a computation resource in one-way quantum
computation schemes. A qubit model has been designed as a
stochastic oscillator formed by a pair of coupled limit cycle
oscillators with chaotically modulated limit cycle radii and
frequencies. The qubit simulates the behavior of electric field of
polarized light beam and adequately imitates the states of two-level
quantum system. A cluster of entangled qubits can be associated
with a beam of polarized light, light polarization degree being
directly related to cluster entanglement degree. Oscillatory network,
imitating qubit cluster, is designed, and system of equations for
network dynamics has been written. The constructions of one-qubit
gates are suggested. Changing of cluster entanglement degree caused
by measurements can be exactly calculated.
Abstract: The electrical substation components are often subject to degradation due to over-voltage or over-current, caused by a short circuit or a lightning. A particular interest is given to the circuit breaker, regarding the importance of its function and its dangerous failure. This component degrades gradually due to the use, and it is also subject to the shock process resulted from the stress of isolating the fault when a short circuit occurs in the system. In this paper, based on failure mechanisms developments, the wear out of the circuit breaker contacts is modeled. The aim of this work is to evaluate its reliability and consequently its residual lifetime. The shock process is based on two random variables such as: the arrival of shocks and their magnitudes. The arrival of shocks was modeled using homogeneous Poisson process (HPP). By simulation, the dates of short-circuit arrivals were generated accompanied with their magnitudes. The same principle of simulation is applied to the amount of cumulative wear out contacts. The objective reached is to find the formulation of the wear function depending on the number of solicitations of the circuit breaker.
Abstract: This paper presents findings from the evaluation study carried out to review the UAE national ID card software. The paper consults the relevant literature to explain many of the concepts and frameworks explained herein. The findings of the evaluation work that was primarily based on the ISO 9126 standard for system quality measurement highlighted many practical areas that if taken into account is argued to more likely increase the success chances of similar system implementation projects.
Abstract: The use of solar control film on windows as one of
solar passive strategies for building have becoming important and is
gaining recognition. Malaysia located close to equator is having
warm humid climate with long sunshine hours and abundant solar
radiation throughout the year. Hence, befitting solar control on
windows is absolutely necessary to capture the daylight whilst
moderating thermal impact and eliminating glare problems. This is
one of the energy efficient strategies to achieve thermal and visual
comfort in buildings. Therefore, this study was carried out to
investigate the effect of window solar controls on thermal and visual
performance of naturally ventilated buildings. This was conducted via
field data monitoring using a test building facility. Four types of
window glazing systems were used with three types of solar control
films. Data were analysed for thermal and visual impact with
reference to thermal and optical characteristics of the films. Results
show that for each glazing system, the surface temperature of
windows are influenced by the Solar Energy Absorption property, the
indoor air temperature are influenced by the Solar Energy
Transmittance and Solar Energy Reflectance, and the daylighting by
Visible Light Transmission and Shading Coefficient. Further
investigations are underway to determine the mathematical relation
between thermal energy and visual performance with the thermal and
optical characteristics of solar control films.
Abstract: Effect of temperature and light was investigated on a
thin film of organic semiconductor formyl-TIPPCu(II) deposited on a
glass substrate with preliminary evaporated gold electrodes. The
electrical capacitance and resistance of the fabricated device were
evaluated under the effect of temperature and light. The relative
capacitance of the fabricated sensor increased by 4.3 times by rising
temperature from 27 to 1870C, while under illumination up to 25000
lx, the capacitance of the Au/formyl-TIPPCu(II)/Au photo capacitive
sensor increased continuously by 13.2 times as compared to dark
conditions.
Abstract: A fault detection and identification (FDI) technique is
presented to create a fault tolerant control system (FTC). The fault
detection is achieved by monitoring the position of the light source
using an array of light sensors. When a decision is made about the
presence of a fault an identification process is initiated to locate the
faulty component and reconfigure the controller signals. The signals
provided by the sensors are predictable; therefore the existence of a
fault is easily identified. Identification of the faulty sensor is based on
the dynamics of the frame. The technique is not restricted to a
particular type of controllers and the results show consistency.
Abstract: Cloud Computing is an approach that provides computation and storage services on-demand to clients over the network, independent of device and location. In the last few years, cloud computing became a trend in information technology with many companies that transfer their business processes and applications in the cloud. Cloud computing with service oriented architecture has contributed to rapid development of Geographic Information Systems. Open Geospatial Consortium with its standards provides the interfaces for hosted spatial data and GIS functionality to integrated GIS applications. Furthermore, with the enormous processing power, clouds provide efficient environment for data intensive applications that can be performed efficiently, with higher precision, and greater reliability. This paper presents our work on the geospatial data services within the cloud computing environment and its technology. A cloud computing environment with the strengths and weaknesses of the geographic information system will be introduced. The OGC standards that solve our application interoperability are highlighted. Finally, we outline our system architecture with utilities for requesting and invoking our developed data intensive applications as a web service.
Abstract: Hardness of the widely used structural steel is of vital
importance since it may help in the determination of many
mechanical properties of a material under loading situations. In order
to obtain reliable information for design, properties homogeneity
should be validated. In the current study the hardness variation over
the different diameters of the same AISI 4140 bar is investigated.
Measurements were taken on the two faces of the stock at equally
spaced eight sectors and fifteen layers. Statistical and graphical
analysis are performed to asses the distribution of hardness
measurements over the specified area. Hardness measurements
showed some degree of dispersion with about ± 10% of its nominal
value provided by manufacturer. Hardness value is found to have a
slight decrease trend as the diameter is reduced. However, an
opposite behavior is noticed regarding the sequence of the sector
indicating a nonuniform distribution over the same area either on the
same face or considering the corresponding sector on the other face
(cross section) of the same material bar.
Abstract: Heavy rainfall greatly affects the aerodynamic performance of the aircraft. There are many accidents of aircraft caused by aerodynamic efficiency degradation by heavy rain. In this Paper we have studied the heavy rain effects on the aerodynamic efficiency of NACA 64-210 & NACA 0012 airfoils. For our analysis, CFD method and preprocessing grid generator are used as our main analytical tools, and the simulation of rain is accomplished via two phase flow approach-s Discrete Phase Model (DPM). Raindrops are assumed to be non-interacting, non-deforming, non-evaporating and non-spinning spheres. Both airfoil sections exhibited significant reduction in lift and increase in drag for a given lift condition in simulated rain. The most significant difference between these two airfoils was the sensitivity of the NACA 64-210 to liquid water content (LWC), while NACA 0012 performance losses in the rain environment is not a function of LWC . It is expected that the quantitative information gained in this paper will be useful to the operational airline industry and greater effort such as small scale and full scale flight tests should put in this direction to further improve aviation safety.