Abstract: Myoelectric control system is the fundamental
component of modern prostheses, which uses the myoelectric signals
from an individual’s muscles to control the prosthesis movements.
The surface electromyogram signal (sEMG) being noninvasive has
been used as an input to prostheses controllers for many years.
Recent technological advances has led to the development of
implantable myoelectric sensors which enable the internal
myoelectric signal (MES) to be used as input to these prostheses
controllers. The intramuscular measurement can provide focal
recordings from deep muscles of the forearm and independent signals
relatively free of crosstalk thus allowing for more independent
control sites. However, little work has been done to compare the two
inputs. In this paper we have compared the classification accuracy of
six pattern recognition based myoelectric controllers which use
surface myoelectric signals recorded using untargeted (symmetric)
surface electrode arrays to the same controllers with multichannel
intramuscular myolectric signals from targeted intramuscular
electrodes as inputs. There was no significant enhancement in the
classification accuracy as a result of using the intramuscular EMG
measurement technique when compared to the results acquired using
the surface EMG measurement technique. Impressive classification
accuracy (99%) could be achieved by optimally selecting only five
channels of surface EMG.
Abstract: Creativity is marked by the ability or power, to
produce through imaginative skill and create something anew. The
University is one of the great places to improve the talent in
imaginative skill. The purpose of this study was to identify a
creativity of the student in presentation product development. Two
hundred seventeen Technical and Vocational Education (TVE)
students in Universiti Tun Hussein Onn had chosen as a respondent.
This study is to survey the level of creativity which is focused on
knowledge, skills, presentation style, and character of creative
personnel. The level of creativity was measured based on the scale at
low, medium and high followed by mean score level. The data
collected by questionnaire, then analyzed using SPSS version
20.0.The result of the study indicated that the students showed a
higher of creativity (mean score in Knowledge = 4.12 and Skills=
4.02). In conjunction with the findings, implications and
recommendations were suggested forward like to ensconce the
research and improve with a more creativity concept in presentation
product of development for learning and teaching process.
Abstract: Teaching of mathematics to engineering students is an
open ended problem in education. The main goal of mathematics
learning for engineering students is the ability of applying a wide
range of mathematical techniques and skills in their engineering
classes and later in their professional work. Most of the
undergraduate engineering students and faculties feels that no efforts
and attempts are made to demonstrate the applicability of various
topics of mathematics that are taught thus making mathematics
unavoidable for some engineering faculty and their students. The lack
of understanding of concepts in engineering mathematics may hinder
the understanding of other concepts or even subjects. However, for
most undergraduate engineering students, mathematics is one of the
most difficult courses in their field of study. Most of the engineering students never understood mathematics or
they never liked it because it was too abstract for them and they could
never relate to it. A right balance of application and concept based
teaching can only fulfill the objectives of teaching mathematics to
engineering students. It will surely improve and enhance their
problem solving and creative thinking skills. In this paper, some practical (informal) ways of making
mathematics-teaching application based for the engineering students
is discussed. An attempt is made to understand the present state of
teaching mathematics in engineering colleges. The weaknesses and
strengths of the current teaching approach are elaborated. Some of
the causes of unpopularity of mathematics subject are analyzed and a
few pragmatic suggestions have been made. Faculty in mathematics
courses should spend more time discussing the applications as well as
the conceptual underpinnings rather than focus solely on strategies
and techniques to solve problems. They should also introduce more
‘word’ problems as these problems are commonly encountered in
engineering courses. Overspecialization in engineering education
should not occur at the expense of (or by diluting) mathematics and
basic sciences. The role of engineering education is to provide the
fundamental (basic) knowledge and to teach the students simple
methodology of self-learning and self-development. All these issues
would be better addressed if mathematics and engineering faculty
join hands together to plan and design the learning experiences for
the students who take their classes. When faculties stop competing
against each other and start competing against the situation, they will
perform better. Without creating any administrative hassles these
suggestions can be used by any young inexperienced faculty of
mathematics to inspire engineering students to learn engineering
mathematics effectively.
Abstract: Concrete is an essential building material which is
widely used in construction industry all over the world due to its
compressible strength. Curing of concrete plays a vital role in
durability and other performance necessities. Improper curing can
affect the concrete performance and durability easily. When areas
like scarcity of water, structures is not accessible by humans external
curing cannot be performed, so we opt for internal curing. Internal
curing (or) self curing plays a major role in developing the concrete
pore structure and microstructure. The concept of internal curing is to
enhance the hydration process to maintain the temperature uniformly.
The evaporation of water in the concrete is reduced by self curing
agent (Super Absorbing Polymer – SAP) there by increasing the
water retention capacity of the concrete. The research work was
carried out to reduce water, which is prime material used for concrete
in the construction industry. Concrete curing plays a major role in
developing hydration process. Concept of self curing will reduce the
evaporation of water from concrete. Self curing will increase water
retention capacity as compared to the conventional concrete. Proper
self curing (or) internal curing increases the strength, durability and
performance of concrete. Super absorbing Polymer (SAP) used as
internal curing agent. In this study 0.2% to 0.4% of SAP was varied
in different grade of high strength concrete. In the experiment
replacement of cement by silica fumes with 5%, 10% and 15% are
studied. It is found that replacement of silica fumes by 10 % gives
more strength and durability when compared to others.
Abstract: The construction of most coastal infrastructure developments around the world are usually made considering wave height, current velocities and river discharges; however, little effort has been paid to surveying sediment transport during dredging or the modification to currents outside the ports or marinas during and after the construction. This study shows a complete survey during the construction of one of the largest ports of the Gulf of Mexico. An anchored Acoustic Doppler Current Velocity profiler (ADCP), a towed ADCP and a combination of model outputs were used at the Veracruz port construction in order to describe the hourly sediment transport and current modifications in and out of the new port. Owing to the stability of the system the new port was construction inside Vergara Bay, a low wave energy system with a tidal range of up to 0.40 m. The results show a two-current system pattern within the bay. The north side of the bay has an anticyclonic gyre, while the southern part of the bay shows a cyclonic gyre. Sediment transport trajectories were made every hour using the anchored ADCP, a numerical model and the weekly data obtained from the towed ADCP within the entire bay. The sediment transport trajectories were carefully tracked since the bay is surrounded by coral reef structures which are sensitive to sedimentation rate and water turbidity. The survey shows that during dredging and rock input used to build the wave breaker sediments were locally added (< 2500 m2) and local currents disperse it in less than 4 h. While the river input located in the middle of the bay and the sewer system plant may add more than 10 times this amount during a rainy day or during the tourist season. Finally, the coastal line obtained seasonally with a drone suggests that the southern part of the bay has not been modified by the construction of the new port located in the northern part of the bay, owing to the two subsystem division of the bay.
Abstract: Geological structure formed by volcanic activities shows polymorphic characteristics due to repeated cooling and hardening of lava. The Jeju region is showing polymorphic characteristics in which clinker layers are irregularly distributed along with vesicular basalt due to volcanic activities. Accordingly, resident damages and environmental disputes occur frequently in the Jeju region due to blasting. The purpose of this study is to develop a blast vibration equation considering the polymorphic characteristics of basaltic ground in Jeju. The blast vibration equation consists of a functional formula of the blasting vibration constant K that changes according to ground characteristics, and attenuation index n. The case study results in Jeju showed that if there are clinker layers, attenuation index n showed a distribution of -1.32~-1.81, whereas if there are no clinker layers, n was -2.79. Moreover, if there are no clinker layers, the frequency of blast vibration showed a high frequency band from 30Hz to 100Hz, while in rocks with clinker layers it showed a low frequency band from 10Hz to 20Hz.
Abstract: Nanotechnology in pristine sense refers to building of
structures at atomic and molecular scale. Meticulously
nanotechnology encompasses the nanomaterials with at least one
dimension size ranging from 1 to 100 nanometres. Unlike the literal
meaning of its name, nanotechnology is a massive concept beyond
imagination. This paper predominantly deals with relevance of
nanotechnology in automotive industries. New generation of
automotives looks at nanotechnology as an emerging trend of
manufacturing revolution. Intricate shapes can be made out of fairly
inexpensive raw materials instead of conventional fabrication
process. Though the current era have enough technology to face
competition, nanotechnology can give futuristic implications to pick
up the modern pace. Nanotechnology intends to bridge the gap
between automotives with superior technical performance and their
cost fluctuation. Preliminarily, it is an area of great scientific interest
and a major shaper of many new technologies. Nanotechnology can
be an ideal building block for automotive industries, under constant
evolution offering a very wide scope of activity. It possesses huge
potential and is still in the embryonic form of research and
development.
Abstract: Energy has a prominent role for development of
nations. Countries which have energy resources also have strategic
power in the international trade of energy since it is essential for all
stages of production in the economy. Thus, it is important for
countries to analyze the weaknesses and strength of the system. On
the other side, international trade is one of the fields that are analyzed
as a complex network via network analysis. Complex network is one
of the tools to analyze complex systems with heterogeneous agents
and interaction between them. A complex network consists of nodes
and the interactions between these nodes. Total properties which
emerge as a result of these interactions are distinct from the sum of
small parts (more or less) in complex systems. Thus, standard
approaches to international trade are superficial to analyze these
systems. Network analysis provides a new approach to analyze
international trade as a network. In this network, countries constitute
nodes and trade relations (export or import) constitute edges. It
becomes possible to analyze international trade network in terms of
high degree indicators which are specific to complex networks such
as connectivity, clustering, assortativity/disassortativity, centrality,
etc. In this analysis, international trade of crude oil and coal which
are types of fossil fuel has been analyzed from 2005 to 2014 via
network analysis. First, it has been analyzed in terms of some
topological parameters such as density, transitivity, clustering etc.
Afterwards, fitness to Pareto distribution has been analyzed via
Kolmogorov-Smirnov test. Finally, weighted HITS algorithm has
been applied to the data as a centrality measure to determine the real
prominence of countries in these trade networks. Weighted HITS
algorithm is a strong tool to analyze the network by ranking countries
with regards to prominence of their trade partners. We have
calculated both an export centrality and an import centrality by
applying w-HITS algorithm to the data. As a result, impacts of the
trading countries have been presented in terms of high-degree
indicators.
Abstract: This paper explored the challenges faced by the
management of a Ghanaian state enterprise in managing conflicts and
disturbances associated with its attempt to implement new work
practices to enhance its capability to operate as a commercial entity.
The purpose was to understand the extent to which organizational
involvement, consistency and adaptability influence employees’
consumption of new work practices in transforming the
organization’s organizational activity system. Using selfadministered
questionnaires, data were collected from one hundred
and eighty (180) employees and analyzed using both descriptive and
inferential statistics. The results showed that constraints in
organizational involvement and adaptability prevented the positive
consumption of new work practices by employees in the
organization. It is also found that the organization’s employees failed
to consume the new practices being implemented, because they
perceived the process as non-involving, and as such, did not
encourage the development of employee capability, empowerment,
and teamwork. The study concluded that the failure of the
organization’s management to create opportunities for organizational
learning constrained its ability to get employees consume the new
work practices, which situation could have facilitated the
organization’s capabilities of operating as a commercial entity.
Abstract: The study of the aerodynamics related to the
improvement in the acting of airplanes and automobiles with the
objective of being reduced the effect of the attrition of the air on
structures, providing larger speeds and smaller consumption of fuel.
The application of the knowledge of the aerodynamics not more
limits to the aeronautical and automobile industries. Therefore, this
research aims to design and construction of a wind tunnel to perform
aerodynamic analysis in bodies of cars, seeking greater efficiency.
Therefore, this research aims to design and construction of a wind
tunnel to perform aerodynamic analysis in bodies of cars, seeking
greater efficiency. For this, a methodology for wind tunnel type
selection is designed to be built, taking into account the various
existing configurations in which chose to build an open circuit tunnel,
due to the lower complexity of construction and installation;
operational simplicity and low cost. The guidelines for the project
were teaching: the layer that limits study and analyze specimens with
different geometries. For the variation of pressure in the test, section
of a switched gauge used a pitot tube. Thus, it was possible to obtain
quantitative and qualitative results, which proved to be satisfactory.
Abstract: The paper focuses on the distance laboratory
organisation for training the electrical engineering staff and students
in the fields of electrical drive and power electronics. To support
online knowledge acquisition and professional enhancement, new
challenges in remote education based on an active learning approach
with self-assessment have been emerged by the authors. Following
the literature review and explanation of the improved assessment
methodology, the concept and technological basis of the labs
arrangement are presented. To decrease the gap between the distance
study of the up-to-date equipment and other educational activities in
electrical engineering, the improvements in the following-up the
learners’ progress and feedback composition are introduced. An
authoring methodology that helps to personalise knowledge
acquisition and enlarge Web-based possibilities is described.
Educational management based on self-assessment is discussed.
Abstract: In this research, we propose to conduct diagnostic and
predictive analysis about the key factors and consequences of urban
population relocation. To achieve this goal, urban simulation models
extract the urban development trends as land use change patterns from
a variety of data sources. The results are treated as part of urban big
data with other information such as population change and economic
conditions. Multiple data mining methods are deployed on this data to
analyze nonlinear relationships between parameters. The result
determines the driving force of population relocation with respect to
urban sprawl and urban sustainability and their related parameters.
This work sets the stage for developing a comprehensive urban
simulation model for catering to specific questions by targeted users. It
contributes towards achieving sustainability as a whole.
Abstract: In this corporate world, the technology of Web
services has grown rapidly and its significance for the development
of web based applications gradually rises over time. The success of
Business to Business integration rely on finding novel partners and
their services in a global business environment. However, the
selection of the most suitable Web service from the list of services
with the identical functionality is more vital. The satisfaction level of
the customer and the provider’s reputation of the Web service are
primarily depending on the range it reaches the customer’s
requirements. In most cases, the customer of the Web service feels
that he is spending for the service which is undelivered. This is
because the customer always thinks that the real functionality of the
web service is not reached. This will lead to change of the service
frequently. In this paper, a framework is proposed to evaluate the
Quality of Service (QoS) and its cost that makes the optimal
correlation between each other. In addition, this research work
proposes some management decision against the functional deviancy
of the web service that is guaranteed at time of selection.
Abstract: Holistic methods covering the development process as
a whole – e.g. systems engineering – have established themselves in
product design. However, technical product optimization,
representing improvements in efficiency and/or minimization of loss,
usually applies to single components of a system. A holistic approach
is being defined based on a hierarchical point of view of systems
engineering. This is subsequently presented using the example of an
electromechanical flywheel energy storage system for automotive
applications.
Abstract: The overall goal of this paper is to examine the
suitability and potential of the policies addressing the sustainability
and affordability of housing for returnees, and to determine the impact
of this policy on housing delivery for Afghan refugees. Housing is a
central component of the settlement experience of refugees. A positive
housing situation can facilitate many aspects of integration.
Unaffordable, and unsafe housing, however, can cause disruptions in
the entire settlement process. This paper aims to identify a suite of
built forms for housing that is both affordable and environmentally
sustainable for Afghan refugees. The result was the development of a
framework that enables the assessment of the overall performance of
various types of housing development in all zones of the country.
There is very little evidence that the present approach of housing
provision to the vagaries of market forces has provided affordable
housing, especially for Afghan refugees. There is a need to incorporate
social housing into the policy to assist people who cannot afford to
have their own houses.
Abstract: One of prevailing modes of finance in emerging
Islamic banking system is Murabah’a. It means a financial dealing or
transaction in which seller tells cost of the goods to be sold to buyer.
Otherwise, the transaction would become invalid. In this mainstream,
import Murabah’a transaction is divergent in such a way that the cost
is not recognized and identified due to execution of import
transaction in foreign currency i.e. US Dollar and the next transaction
of Murabaha’a with the client is executed in local currency. Since this
transaction is executed in dual currency i.e. bank pays supplier in
foreign currency and executes Murabah’a with its client in local
currency and it is not allowed in according to Islamic Injunctions as
mentioned in hadith narrated by Hazrat Ibn-e-Umar (May Allah be
pleased with them) used to sell his camels with Dirhams and take
dinars instead and vice versa. Upon revealing before the Prophet
(Peace be upon him), he was advised that it must not be contingent in
the agreement and the ready rate would be applied and possession of
one of the consideration is compulsory. The solution in this regard is
that the import Murabah’a transaction should be in single currency
However, other currency can be paid in payment at the time of
payment in a very indispensable situation provided that ready rate
would be applied. Moreover, some of other solutions have also been
given in this regard.
Abstract: There was a scenario present day that drying of fresh
fruits and vegetables by indirect solar drying by using mechanical
device; hence, an effort was made to develop a small scale solar
tunnel dryer (STD). Drying of spinach is carried out to analyze the
performance of the dryer and to study its drying characteristics. To
evaluate the performance of dryer the independent variables were
selected as air flow rate, loading density and shade net while collector
efficiency, drying efficiency, overall efficiency and specific energy
consumption were selected as responses during performing the
experiments. The spinach was dried from initial moisture content
88.21-94.04% (w.b.) to final moisture content 3.50-5.13% (w.b.). The
drying time considerably reduced as compared to open sun drying of
spinach as sun drying took 15 h for drying. The average collector
efficiency, drying efficiency and overall efficiency were in the range
28.73-61.15%, 11.63% to 22.13%, and 7.61-14.66%, respectively.
Abstract: With the advancement of knowledge about the utility
and impact of sustainability, its feasibility has been explored into
different walks of life. Scientists, however; have established their
knowledge in four areas viz environmental, economic, social and
cultural, popularly termed as four pillars of sustainability. Aspects of
environmental and economic sustainability have been rigorously
researched and practiced and huge volume of strong evidence of
effectiveness has been founded for these two sub-areas. For the social
and cultural aspects of sustainability, dependable evidence of
effectiveness is still to be instituted as the researchers and
practitioners are developing and experimenting methods across the
globe. Therefore, the present research aimed to identify globally used
practices of social and cultural sustainability and through evidence
synthesis assess their outcomes to determine the effectiveness of
those practices. A PICO format steered the methodology which
included all populations, popular sustainability practices including
walkability/cycle tracks, social/recreational spaces, privacy, health &
human services and barrier free built environment, comparators
included ‘Before’ and ‘After’, ‘With’ and ‘Without’, ‘More’ and
‘Less’ and outcomes included Social well-being, cultural coexistence,
quality of life, ethics and morality, social capital, sense of
place, education, health, recreation and leisure, and holistic
development. Search of literature included major electronic
databases, search websites, organizational resources, directory of
open access journals and subscribed journals. Grey literature,
however, was not included. Inclusion criteria filtered studies on the
basis of research designs such as total randomization, quasirandomization,
cluster randomization, observational or single studies
and certain types of analysis. Studies with combined outcomes were
considered but studies focusing only on environmental and/or
economic outcomes were rejected. Data extraction, critical appraisal
and evidence synthesis was carried out using customized tabulation,
reference manager and CASP tool. Partial meta-analysis was carried
out and calculation of pooled effects and forest plotting were done.
As many as 13 studies finally included for final synthesis explained
the impact of targeted practices on health, behavioural and social
dimensions. Objectivity in the measurement of health outcomes
facilitated quantitative synthesis of studies which highlighted the
impact of sustainability methods on physical activity, Body Mass
Index, perinatal outcomes and child health. Studies synthesized
qualitatively (and also quantitatively) showed outcomes such as
routines, family relations, citizenship, trust in relationships, social
inclusion, neighbourhood social capital, wellbeing, habitability and
family’s social processes. The synthesized evidence indicates slight
effectiveness and efficacy of social and cultural sustainability on the
targeted outcomes. Further synthesis revealed that such results of this
study are due weak research designs and disintegrated implementations. If architects and other practitioners deliver their
interventions in collaboration with research bodies and policy
makers, a stronger evidence-base in this area could be generated.
Abstract: The acceptance of sustainable products by the final
consumer is still one of the challenges of the industry, which
constantly seeks alternative approaches to successfully be accepted in
the global market. A large set of methods and approaches have been
discussed and analysed throughout the literature. Considering the current need for sustainable development and the
current pace of consumption, the need for a combined solution
towards the development of new products became clear, forcing
researchers in product development to propose alternatives to the
previous standard product development models. This paper presents, through a systemic analysis of the literature
on product development, eco-design and consumer involvement, a set
of alternatives regarding consumer involvement towards the
development of sustainable products and how these approaches could
help improve the sustainable industry’s establishment in the general
market. Still being developed in the course of the author’s PhD, the initial
findings of the research show that the understanding of the benefits of
sustainable behaviour lead to a more conscious acquisition and
eventually to the implementation of sustainable change in the
consumer. Thus this paper is the initial approach towards the
development of new sustainable products using the fashion industry
as an example of practical implementation and acceptance by the
consumers. By comparing the existing literature and critically analysing it, this
paper concluded that the consumer involvement is strategic to
improve the general understanding of sustainability and its features.
The use of consumers and communities has been studied since the
early 90s in order to exemplify uses and to guarantee a fast
comprehension. The analysis done also includes the importance of
this approach for the increase of innovation and ground breaking
developments, thus requiring further research and practical
implementation in order to better understand the implications and
limitations of this methodology.
Abstract: This research work is an experimental study, through
development of an adhesive from Prosopis africana endosperm. The
prosopis seed for this work were obtained from Enugu State in the
South East part of Nigeria. The seeds were prepared by separating the
endosperm from the seed coat and cotyledon. Three methods were
used to separate them, which are acidic method, roasting method and
boiling method. 20g of seed were treated with different
concentrations (25, 40, 55, 70, and 85% w/w) at 100°C and constant
time (30 minutes), under continuous stirring with magnetic stirrer.
Also 20g of seed were treated with sulphuric acid of concentrations
40% w/w at 100°C with different time (10, 15, 20, 25, 30 minutes),
under continuous stirring with magnetic stirrer. Finally, 20g of seed
were treated with sulphuric acid of concentrations 40% w/w at
different temperature (20°C, 40°C, 60°C, 80°C, and 100°C) with
constant time (30 minutes), under continuous stirring with magnetic
stirrer. The whole endosperm extracted was adhesive. The physical
properties of the adhesive were determined (appearance, odour, taste,
solubility, pH, size, and binding strength). The percentage of the
adhesive yield makes the commercialization of the seed in Nigeria
possible and profitable. The very high viscosity attained at low
concentrations makes prosopis adhesive an excellent thickener in the
food industry.