Abstract: A Rotary Disc Contactor with inner diameter of
9.1cm and maximum operating height of 40cm has been used to
investigate break up phenomenon. Water-Toluene, Water as
continuous phase and Toluene as dispersed phase, was selected as
chemical system in the experiments. The mentioned chemical system
has high interfacial tension so it was possible to form big drops
which permit accurate investigation on break up phenomenon as well
as the first and second critical rotor speeds.
In this study, Break up phenomenon has been studied as a function
of mother drop size, rotor speed and continuous phase height. Further
more; the effects of mother drop size and continuous phase height on
the first and second critical rotor speeds were investigated. Finally,
two modified correlations were proposed to estimate the first and
second critical speeds.
Abstract: In the current research, we present an operation framework and protection mechanism to facilitate secure environment to protect mobile agents against tampering. The system depends on the presence of an authentication authority. The advantage of the proposed system is that security measures is an integral part of the design, thus common security retrofitting problems do not arise. This is due to the presence of AlGamal encryption mechanism to protect its confidential content and any collected data by the agent from the visited host . So that eavesdropping on information from the agent is no longer possible to reveal any confidential information. Also the inherent security constraints within the framework allow the system to operate as an intrusion detection system for any mobile agent environment. The mechanism is tested for most of the well known severe attacks against agents and networked systems. The scheme proved a promising performance that makes it very much recommended for the types of transactions that needs highly secure environments, e. g., business to business.
Abstract: Team distillation assisted by microwave extraction
(SDAM) considered as accelerated technique extraction is a
combination of microwave heating and steam distillation, performed
at atmospheric pressure. SDAM has been compared with the same
technique coupled with the cryogrinding of seeds (SDAM -CG).
Isolation and concentration of volatile compounds are performed by a
single stage for the extraction of essential oil from Cuminum
cyminum seeds. The essential oils extracted by these two methods for
5 min were quantitatively (yield) and qualitatively (aromatic profile)
no similar. These methods yield an essential oil with higher amounts
of more valuable oxygenated compounds, and allow substantial
savings of costs, in terms of time, energy and plant material. SDAM
and SDAM-CG is a green technology and appears as a good
alternative for the extraction of essential oils from aromatic plants.
Abstract: The primary education system in Indonesia involved the community recognized as the school committee, to take a part in the process of achieving the quality of education via the school facility performance, the low level of school committee involvement in the education system has become the issue in the development of education and reflected to the quality of education. This paper will discuss the conceptual framework and methodology for the performance of school committees within the management of school facilities in Batubara district of Indonesia. The concepts of Community based Facility Management (CbFM) and Logometrix are used as a basis to measure the school committee performance in order to address the needs of quality school management. The data will be taken from questionnaires distributed for those who work and use school facilities spread over seven sub district of Batubara, Indonesia. The result of this study is expected to provide a guide for evaluating the performance of existing school committee in improving the quality of education in Indonesia.
Abstract: In the present research, steam cracking of two types of
feedstocks i.e., naphtha and ethane is simulated for Pyrocrack1-1 and
2/2 coil configurations considering two key parameters of coil outlet
temperature (COT) and coil capacity using a radical based kinetic
model. The computer model is confirmed using the industrial data
obtained from Amirkabir Petrochemical Complex. The results are in
good agreement with performance data for naphtha cracking in a
wide range of severity (0.4-0.7), and for ethane cracking on various
conversions (50-70). It was found that Pyrocrack2-2 coil type is an
appropriate choice for steam cracking of ethane at reasonable
ethylene yield while resulting in much lower tube wall temperature
while Pyrocrack1-1 coil type is a proper selection for liquid
feedstocks i.e. naphtha. It can be used for cracking of liquid
feedstocks at optimal ethylene yield whereas not exceeding the
allowable maximum tube temperature.
Abstract: Along with forward supply chain organization needs
to consider the impact of reverse logistics due to its economic
advantage, social awareness and strict legislations. In this paper, we
develop a system dynamics framework for a closed-loop supply
chain with fuzzy demand and fuzzy collection rate by incorporating
product exchange policy in forward channel and various recovery
options in reverse channel. The uncertainty issues associated with
acquisition and collection of used product have been quantified using
possibility measures. In the simulation study, we analyze order
variation at both retailer and distributor level and compare bullwhip
effects of different logistics participants over time between the
traditional forward supply chain and the closed-loop supply chain.
Our results suggest that the integration of reverse logistics can reduce
order variation and bullwhip effect of a closed-loop system. Finally,
sensitivity analysis is performed to examine the impact of various
parameters on recovery process and bullwhip effect.
Abstract: The purpose of this study is to revisit the concept of
rape as represented by professionals in the literature as well as its
perception (beliefs and attitudes) in the population at large and to
propose methodological improvements to its measurement tool. Rape
is a serious crime threatening its victim-s physical and mental health
and integrity; and as such is legally prosecuted in all modern
societies. The problem is not in accepting or rejecting rape as a
criminal act, but rather in the vagueness of its interpretations and
“justifications" maintained in the mentality of modern societies -
known in the literature as the phenomenon of "rape-myth". The rapemyth
can be studied from different perspectives: criminology,
sociology, ethics, medicine and psychology. Its investigation requires
rigorous scientific objectivity, free of passion (victims of rape are at
risk of emotional bias), free of activism (social activists, even if wellintentioned
are also biased), free of any pre-emptive assumptions or
prejudices. To apply a rigorous scientific procedure, we need a solid,
valid and reliable measurement. Rape is a form of heterosexual or
homosexual aggression, violently forcing the victim to give-in in the
sexual activity of the aggressor against her/his will. Human beings
always try to “understand" or find a reason justifying their acts.
Psychological literature provides multiple clinical and experimental
examples of it; just to mention the famous studies by Milgram on the
level of electroshock delivered by the “teacher" towards the “learner"
if “scientifically justifiable" or the studies on the behavior of
“prisoners" and the “guards" and many other experiments and field
observations. Sigmund Freud presented the phenomenon of
unconscious justification and called it rationalization. The multiple
justifications, rationalizations and repeated opinions about sexual
behavior contribute to a myth maintained in the society. What kind of
“rationale" our societies apply to “understand" the non-consensual
sexual behavior? There are many, just to mention few:
• Sex is a ludistic activity for both participants, therefore –
even if not consented – it should bring pleasure to both.
• Everybody wants sex, but only men are allowed to manifest
it openly while women have to pretend the opposite, thus men have
to initiate sexual behavior and women would follow.
• A person who strongly needs sex is free to manifest it and
struggle to get it; the person who doesn-t want it must not reveal
her/his sexual attraction and avoid risky situations; otherwise she/he
is perceived as a promiscuous seducer.
• A person who doesn-t fight against the sexual initiator
unconsciously accepts the rape (does it explain why homosexual
rapes are reported less frequently than rapes against women?).
• Women who are raped deserve it because their wardrobe is
very revealing and seducing and they ''willingly'' go to highly risky
places (alleys, dark roads, etc.).
• Men need to ventilate their sexual energy and if they are
deprived of a partner their urge to have sex is difficult to control.
• Men are supposed to initiate and insist even by force to have
sex (their testosterone makes them both sexual and aggressive).
The paper overviews numerous cultural beliefs about masculine
versus feminine behavior and their impact on the “rape myth".
Abstract: Sustainability in rural production system can only be achieved if it can suitably satisfy the local requirement as well as the outside demand with the changing time. With the increased pressure from the food sector in a globalised world, the agrarian economy
needs to re-organise its cultivable land system to be compatible with new management practices as well as the multiple needs of various stakeholders and the changing resource scenario. An attempt has been made to transform this problem into a multi-objective decisionmaking problem considering various objectives, resource constraints and conditional constraints. An interactive fuzzy multi-objective
programming approach has been used for such a purpose taking a
case study in Indian context to demonstrate the validity of the method.
Abstract: Location-based services (LBS) exploit the known
location of a user to provide services dependent on their geographic
context and personalized needs [1].
The development and arrival of broadband mobile data networks
supported with mobile terminals equipped with new location
technologies like GPS have finally created opportunities for
implementation of LBS applications. But, from the other side,
collecting location information data in general raises privacy
concerns.
This paper presents results from two surveys of LBS acceptance in
Croatia. The first survey was administered on 181 students, and the
second extended survey involved pattern of 180 Croatian citizens.
We developed questionnaire which consists of descriptions of 15
different applications with scale which measures perceptions and
attitudes of users towards these applications.
We report the results to identify potential commercial applications
for LBS in B2C segment. Our findings suggest that some types of
applications like emergency&safety services and navigation have
significantly higher rate of acceptance than other types.
Abstract: The higher compounded growth rates coupled with
favourable demographics in emerging markets portend abundant
opportunities for multinational organizations. With many
organizations competing for talent in these growing markets, their
ability to succeed will depend on their understanding of local
workforce needs and aspirations. Using data from the Towers Watson
2010 Global Workforce Study, this paper highlights differences in
employee engagement, turnover risks, and attraction and retention
drivers between the two markets. Apart from looking at the
traditional drivers of employee engagement, the study also explores
the value placed by employees on elements like a strong senior
leadership, managerial capabilities and career advancement
opportunities. Results reveal that emerging markets employees seem
to be more engaged and value the non-traditional elements more
highly than the developed markets employees.
Abstract: The Kowsar dam supply water for different usages
such as drinking, industrial, agricultural and aquaculture farms
usages and located next to the city of Dehdashat in Kohgiluye and
Boyerahmad province in southern Iran. There are some towns and
villages on the Kowsar dam watersheds, which Dehdasht and Choram
are the most important and populated cities in this area. The study
was undertaken to assess the status of water quality in the urban areas
of the Kowsar dam. A total of 28 water samples were collected from
6 stations on surface water and 1 station from groundwater on the
watershed of the Kowsar dam. All the samples were analyzed for Ni
concentration using standard procedures. The results were compared
with other national and international standards. Among the analyzed
samples, as the maximum value of Nickel (0.01 mg/L) was observed
on the station 2 at the autumn 2010, all the samples analyzed were
within the maximum admissible limits by the United States
Environmental Protection Agency, EU, WHO and the Iranian. In
general results of the present study have shown that a Ni mean value
of station No. 2 with 0.006 mg/L is higher than the other stations. Ni
level of all samples and stations have had normal values and this is an
indication of pollution potential and hazards because of human
activity and waste water of towns in the areas, which can effect on
human health implications in future. This research, therefore,
recommends the government and other responsible authorities to take
suitable improving measures in the Kowsar dam watersheds.
Abstract: Defining strategic position of the organizations within
the industry environment is one of the basic and most important
phases of strategic planning to which extent that one of the
fundamental schools of strategic planning is the strategic positioning
school. In today-s knowledge-based economy and dynamic
environment, it is essential for universities as the centers of
education, knowledge creation and knowledge worker evolvement.
Till now, variant models with different approaches to strategic
positioning are deployed in defining the strategic position within the
various industries. Balanced Scorecard as one of the powerful models
for strategic positioning, analyzes all aspects of the organization
evenly. In this paper with the consideration of BSC strength in
strategic evaluation, it is used for analyzing the environmental
position of the best-s Iranian Business Schools. The results could be
used in developing strategic plans for these schools as well as other
Iranian Management and Business Schools.
Abstract: The present paper discusses the selection of process
parameters for obtaining optimal nanocrystallites size in the CuOZrO2
catalyst. There are some parameters changing the inorganic
structure which have an influence on the role of hydrolysis and
condensation reaction. A statistical design test method is
implemented in order to optimize the experimental conditions of
CuO-ZrO2 nanoparticles preparation. This method is applied for the
experiments and L16 orthogonal array standard. The crystallites size
is considered as an index. This index will be used for the analysis in
the condition where the parameters vary. The effect of pH, H2O/
precursor molar ratio (R), time and temperature of calcination,
chelating agent and alcohol volume are particularity investigated
among all other parameters. In accordance with the results of
Taguchi, it is found that temperature has the greatest impact on the
particle size. The pH and H2O/ precursor molar ratio have low
influences as compared with temperature. The alcohol volume as
well as the time has almost no effect as compared with all other
parameters. Temperature also has an influence on the morphology
and amorphous structure of zirconia. The optimal conditions are
determined by using Taguchi method. The nanocatalyst is studied by
DTA-TG, XRD, EDS, SEM and TEM. The results of this research
indicate that it is possible to vary the structure, morphology and
properties of the sol-gel by controlling the above-mentioned
parameters.
Abstract: Medical images require special safety and confidentiality because critical judgment is done on the information provided by medical images. Transmission of medical image via internet or mobile phones demands strong security and copyright protection in telemedicine applications. Here, highly secured and robust watermarking technique is proposed for transmission of image data via internet and mobile phones. The Region of Interest (ROI) and Non Region of Interest (RONI) of medical image are separated. Only RONI is used for watermark embedding. This technique results in exact recovery of watermark with standard medical database images of size 512x512, giving 'correlation factor' equals to 1. The correlation factor for different attacks like noise addition, filtering, rotation and compression ranges from 0.90 to 0.95. The PSNR with weighting factor 0.02 is up to 48.53 dBs. The presented scheme is non blind and embeds hospital logo of 64x64 size.
Abstract: This paper argues that a product development exercise
involves in addition to the conventional stages, several decisions
regarding other aspects. These aspects should be addressed
simultaneously in order to develop a product that responds to the
customer needs and that helps realize objectives of the stakeholders
in terms of profitability, market share and the like. We present a
framework that encompasses these different development
dimensions. The framework shows that a product development
methodology such as the Quality Function Deployment (QFD) is the
basic tool which allows definition of the target specifications of a
new product. Creativity is the first dimension that enables the
development exercise to live and end successfully. A number of
group processes need to be followed by the development team in
order to ensure enough creativity and innovation. Secondly,
packaging is considered to be an important extension of the product.
Branding strategies, quality and standardization requirements,
identification technologies, design technologies, production
technologies and costing and pricing are also integral parts to the
development exercise. These dimensions constitute the proposed
framework. The paper also presents a mathematical model used to
calculate the design targets based on the target costing principle. The
framework is used to study a case of a new product development in
the telecommunications services sector.
Abstract: Since the driving speed and control accuracy of
commercial optical disk are increasing significantly, it needs an
efficient controller to monitor the track seeking and following
operations of the servo system for achieving the desired data
extracting response. The nonlinear behaviors of the actuator and servo
system of the optical disk drive will influence the laser spot
positioning. Here, the model-free fuzzy control scheme is employed to
design the track seeking servo controller for a d.c. motor driving
optical disk drive system. In addition, the sliding model control
strategy is introduced into the fuzzy control structure to construct a
1-D adaptive fuzzy rule intelligent controller for simplifying the
implementation problem and improving the control performance. The
experimental results show that the steady state error of the track
seeking by using this fuzzy controller can maintain within the track
width (1.6 μm ). It can be used in the track seeking and track
following servo control operations.
Abstract: Various sounds generated in the chest are included in
auscultation sound. Adaptive Noise Canceller (ANC) is one of the
useful techniques for biomedical signal. But the ANC is not suitable
for auscultation sound. Because the ANC needs two input channels as
a primary signal and a reference signals, but a stethoscope can
provide just one input sound. Therefore, in this paper, it was
proposed the Single Input ANC (SIANC) for suppression of breath
sound in a cardiac auscultation sound. For the SIANC, it was
proposed that the reference generation system which included Heart
Sound Detector, Control and Reference Generator. By experiment
and comparison, it was confirmed that the proposed SIANC was
efficient for heart sound enhancement and it was independent of
variations of a heartbeat.
Abstract: Using of natural lighting has come into prominence in
constructed buildings, especially in last ten years, under scope of
energy efficiency. Natural lighting methods are one of the methods
that aim to take advantage of day light in maximum level and
decrease using of artificial lighting. Increasing of day light amount in
buildings by using suitable methods will give optimum result in
terms of comfort and energy saving when the daylight-artificial light
integration is ensured with a suitable control system. Using of natural
light in places that require lighting will ensure energy saving in great
extent. With this study, it is aimed to save energy used for purpose of
lighting. Under this scope, lighting of a scanning laboratory of a
hospital was realized by using a lighting automation containing
natural and artificial lighting. In natural lighting, light pipes were
used and in artificial lighting, dimmable power LED modules were
used. Necessity of lighting was followed with motion sensors. The
lighting automation containing natural and artificial light was ensured
with fuzzy logic control. At the scanning laboratory where this
application was realized, energy saving in lighting was obtained.
Abstract: Magnesium alloys have gained increased attention in recent years in automotive, electronics, and medical industry. This because of magnesium alloys have better properties than aluminum alloys and steels in respects of their low density and high strength to weight ratio. However, the main problems of magnesium alloy welding are the crack formation and the appearance of porosity during the solidification. This paper proposes a unique technique to weld two thin sheets of AZ31B magnesium alloy using a paste containing Ag nanoparticles. The paste containing Ag nanoparticles of 5 nm in average diameter and an organic solvent was used to coat the surface of AZ31B thin sheet. The coated sheet was heated at 100 °C for 60 s to evaporate the solvent. The dried sheet was set as a lower AZ31B sheet on the jig, and then lap fillet welding was carried out by using a pulsed Nd:YAG laser in a closed box filled with argon gas. The characteristics of the microstructure and the corrosion behavior of the joints were analyzed by opticalmicroscopy (OM), energy dispersive spectrometry (EDS), electron probe micro-analyzer (EPMA), scanning electron microscopy (SEM), and immersion corrosion test. The experimental results show that the wrought AZ31B magnesium alloy can be joined successfully using Ag nanoparticles. Ag nanoparticles insert promote grain refinement, narrower the HAZ width and wider bond width compared to weld without and insert. Corrosion rate of welded AZ31B with Ag nanoparticles reduced up to 44 % compared to base metal. The improvement of corrosion resistance of welded AZ31B with Ag nanoparticles due to finer grains and large grain boundaries area which consist of high Al content. β-phase Mg17Al12 could serve as effective barrier and suppressed further propagation of corrosion. Furthermore, Ag distribution in fusion zone provide much more finer grains and may stabilize the magnesium solid solution making it less soluble or less anodic in aqueous
Abstract: In the paper a method of modeling text for Polish is
discussed. The method is aimed at transforming continuous input text
into a text consisting of sentences in so called canonical form, whose
characteristic is, among others, a complete structure as well as no
anaphora or ellipses. The transformation is lossless as to the content
of text being transformed. The modeling method has been worked
out for the needs of the Thetos system, which translates Polish
written texts into the Polish sign language. We believe that the
method can be also used in various applications that deal with the
natural language, e.g. in a text summary generator for Polish.