Abstract: Three dimensional simulations are carried out to estimate the effect of wind direction, wind speed and geometry on the flow and dispersion of vehicular pollutant in a street canyon. The pollutant sources are motor vehicles passing between the two buildings. Suitable emission factors for petrol and diesel vehicles at varying vehicle speed are used for the estimation of the rate of emission from the streets. The dispersion of automobile pollutant released from the street is simulated by introducing vehicular emission source term as a fixed-flux boundary condition at the ground level over the road. The emission source term is suitably calculated by adopting emission factors from literature for varying conditions of street traffic. It is observed that increase in wind angle disturbs the symmetric pattern of pollution distribution along the street length. The concentration increases in the far end of the street as compared to the near end.
Abstract: In this paper developed and realized absolutely new
algorithm for solving three-dimensional Poisson equation. This
equation used in research of turbulent mixing, computational fluid
dynamics, atmospheric front, and ocean flows and so on. Moreover in
the view of rising productivity of difficult calculation there was
applied the most up-to-date and the most effective parallel
programming technology - MPI in combination with OpenMP
direction, that allows to realize problems with very large data
content. Resulted products can be used in solving of important
applications and fundamental problems in mathematics and physics.
Abstract: The present work analyses different parameters of pressure die casting to minimize the casting defects. Pressure diecasting is usually applied for casting of aluminium alloys. Good surface finish with required tolerances and dimensional accuracy can be achieved by optimization of controllable process parameters such as solidification time, molten temperature, filling time, injection pressure and plunger velocity. Moreover, by selection of optimum process parameters the pressure die casting defects such as porosity, insufficient spread of molten material, flash etc. are also minimized. Therefore, a pressure die casting component, carburetor housing of aluminium alloy (Al2Si2O5) has been considered. The effects of selected process parameters on casting defects and subsequent setting of parameters with the levels have been accomplished by Taguchi-s parameter design approach. The experiments have been performed as per the combination of levels of different process parameters suggested by L18 orthogonal array. Analyses of variance have been performed for mean and signal-to-noise ratio to estimate the percent contribution of different process parameters. Confidence interval has also been estimated for 95% consistency level and three conformational experiments have been performed to validate the optimum level of different parameters. Overall 2.352% reduction in defects has been observed with the help of suggested optimum process parameters.
Abstract: This paper examines the link between gender equality
and climate change policies in Australia. It critically analyses the
extent to which gender mainstreaming and gender dimensions have
been taken into account in the national policy processes for climate
change in Australia. The paper argues that climate change adaptation
and mitigation policies in Australia neglect gender dimensions. This
endangers the advances made in gender equality and works against
socially equitable and effective climate change strategies.
Abstract: This paper investigated the organizational
innovativeness of public listed housing developers in Malaysia. We
conceptualized organizational innovativeness as a multi-dimensional
construct consisting of 5 dimensions: market innovativeness, product
innovativeness, process innovativeness, behavior innovativeness and
strategic innovativeness. We carried out questionnaire survey with all
accessible public listed developers in Malaysia and received a 56
percent response. We found that the innovativeness of public listed
housing developers is low. The study extends the knowledge on
innovativeness theory by using a multi-dimensional contructs to
conceptualize the innovativeness of public listed housing developers
in Malaysia where all this while most studies focused on single
dimensional construct of innovativeness. The paper ends by
providing some explanations for the results.
Abstract: The objective of this research was to find the diffusion properties of vehicles on the road by using the V-Sphere Code. The diffusion coefficient and the size of the height of the wake were estimated with the LES option and the third order MUSCL scheme. We evaluated the code with the changes in the moments of Reynolds Stress along the mean streamline. The results show that at the leading part of a bluff body the LES has some advantages over the RNS since the changes in the strain rates are larger for the leading part. We estimated that the diffusion coefficient with the computed Reynolds stress (non-dimensional) was about 0.96 times the mean velocity.
Abstract: The flow field over a three dimensional pole barn
characterized by a cylindrical roof has been numerically investigated.
Wind pressure and viscous loads acting on the agricultural building
have been analyzed for several incoming wind directions, so as to
evaluate the most critical load condition on the structure. A constant
wind velocity profile, based on the maximum reference wind speed in
the building site (peak gust speed worked out for 50 years return
period) and on the local roughness coefficient, has been simulated.
In order to contemplate also the hazard due to potential air
wedging between the stored hay and the lower part of the ceiling, the
effect of a partial filling of the barn has been investigated.
The distribution of wind-induced loads on the structure have been
determined, allowing a numerical quantification of the effect of wind
direction on the induced stresses acting on a hemicylindrical roof.
Abstract: Tensile armour wires provide a flexible pipe's
resistance to longitudinal stresses. Flexible pipe manufacturers need
to know the effect of defects such as scratches and cracks, with
dimensions less than 0.2mm which is the limit of the current nondestructive
detection technology, on the fracture stress and fracture
strain of the wire for quality assurance purposes. Recent research
involving the determination of the fracture strength of cracked wires
employed laboratory testing and classical fracture mechanics
approach using non-standardised fracture mechanics specimens
because standard test specimens could not be manufactured from the
wires owing to their sizes. In this work, the effect of miniature
cracks on the fracture properties of tensile armour wires was
investigated using laboratory and finite element tensile testing
simulations with the phenomenological shear fracture model. The
investigation revealed that the presence of cracks shallower than
0.2mm is worse on the fracture strain of the wire.
Abstract: The presence of toxic heavy metals in industrial
effluents is one of the serious threats to the environment. Heavy
metals such as Cadmium, Chromium, Lead, Nickel, Zinc, Mercury,
Copper, Arsenic are found in the effluents of industries such as
foundries, electroplating, petrochemical, battery manufacturing,
tanneries, fertilizer, dying, textiles, metallurgical and metal finishing.
Tremendous increase of industrial copper usage and its presence in
industrial effluents has lead to a growing concern about the fate and
effects of Copper in the environment. Percolation of industrial
effluents through soils leads to contamination of ground water and
soils. The transport of heavy metals and their diffusion into the soils
has therefore, drawn the attention of the researchers.
In this study, an attempt has been made to delineate the
mechanisms of transport and fate of copper in terrestrial
environment. Column studies were conducted using perplex glass
square column of dimension side 15 cm and 1.35 m long. The soil
samples were collected from a natural drain near Mohali (India). The
soil was characterized to be poorly graded sandy loam. The soil was
compacted to the field dry density level of about 1.6 g/cm3. Break
through curves for different depths of the column were plotted. The
results of the column study indicated that the copper has high
tendency to flow in the soils and fewer tendencies to get absorbed on
the soil particles. The t1/2 estimates obtained from the studies can be
used for design copper laden wastewater disposal systems.
Abstract: In this paper we present a noise reduction filter for video processing. It is based on the recently proposed two dimensional steering kernel, extended to three dimensions and further augmented to suit the spatial-temporal domain of video processing. Two alternative filters are proposed - the time symmetric kernel and the time asymmetric kernel. The first reduces the noise on single sequences, but to handle the problems at scene shift the asymmetric kernel is introduced. The performance of both are tested on simulated data and on a real video sequence together with the existing steering kernel. The proposed kernels improves the Rooted Mean Squared Error (RMSE) compared to the original steering kernel method on video material.
Abstract: During the last couple of years, the degree of dependence on IT systems has reached a dimension nobody imagined to be possible 10 years ago. The increased usage of mobile devices (e.g., smart phones), wireless sensor networks and embedded devices (Internet of Things) are only some examples of the dependency of modern societies on cyber space. At the same time, the complexity of IT applications, e.g., because of the increasing use of cloud computing, is rising continuously. Along with this, the threats to IT security have increased both quantitatively and qualitatively, as recent examples like STUXNET or the supposed cyber attack on Illinois water system are proofing impressively. Once isolated control systems are nowadays often publicly available - a fact that has never been intended by the developers. Threats to IT systems don’t care about areas of responsibility. Especially with regard to Cyber Warfare, IT threats are no longer limited to company or industry boundaries, administrative jurisdictions or state boundaries. One of the important countermeasures is increased cooperation among the participants especially in the field of Cyber Defence. Besides political and legal challenges, there are technical ones as well. A better, at least partially automated exchange of information is essential to (i) enable sophisticated situational awareness and to (ii) counter the attacker in a coordinated way. Therefore, this publication performs an evaluation of state of the art Intrusion Detection Message Exchange protocols in order to guarantee a secure information exchange between different entities.
Abstract: Increasing energy absorption is a significant parameter
in vehicle design. Absorbing more energy results in decreasing
occupant damage. Limitation of the deflection in a side impact results
in decreased energy absorption (SEA) and increased peak load (PL).
Hence a high crash force jeopardizes passenger safety and vehicle
integrity. The aims of this paper are to determine suitable dimensions
and material of a square beam subjected to side impact, in order to
maximize SEA and minimize PL. To achieve this novel goal, the
geometric parameters of a square beam are optimized using the
response surface method (RSM).multi-objective optimization is
performed, and the optimum design for different response features is
obtained.
Abstract: Injection forging is a Nett-shape manufacturing
process in which one or two punches move axially causing a radial
flow into a die cavity in a form which is prescribed by the exitgeometry,
such as pulley, flanges, gears and splines on a shaft. This
paper presents an experimental and numerical study of the injection
forging of splines in terms of load requirement and material flow.
Three dimensional finite element analyses are used to investigate the
effect of some important parameters in this process. The experiment
has been carried out using solid commercial lead billets with two
different billet diameters and four different dies.
Abstract: The paper discusses European Lifelong Learning policy in the European enlargement to the Balkan. The European Lifelong Learning policy with Human Capital approach is researched in the country case of Macedonia. The paper argues that Human Capital approach focusing on instrumental and economic importance of learning for employability and economic growth needs to be complemented with Capability Approach for intrinsic and noneconomic needs of learning among the ethnic minorities. The paper identifies two dimensions of importance – minority languages and civic education – that the Capability Approach may develop to guarantee equal opportunities to all to benefit from European educational and lifelong learning development and to build an inclusive and socially just democracy in Macedonia.
Abstract: A nucleotide sequence can be expressed as a numerical sequence when each nucleotide is assigned its proton number. A resulting gene numerical sequence can be investigated for its fractal dimension in terms of evolution and chemical properties for comparative studies. We have investigated such nucleotide fluctuation in the 16S rRNA gene of archaea thermophiles. The studied archaea thermophiles were archaeoglobus fulgidus, methanothermobacter thermautotrophicus, methanocaldococcus jannaschii, pyrococcus horikoshii, and thermoplasma acidophilum. The studied five archaea-euryarchaeota thermophiles have fractal dimension values ranging from 1.93 to 1.97. Computer simulation shows that random sequences would have an average of about 2 with a standard deviation about 0.015. The fractal dimension was found to correlate (negative correlation) with the thermophile-s optimal growth temperature with R2 value of 0.90 (N =5). The inclusion of two aracheae-crenarchaeota thermophiles reduces the R2 value to 0.66 (N = 7). Further inclusion of two bacterial thermophiles reduces the R2 value to 0.50 (N =9). The fractal dimension is correlated (positive) to the sequence GC content with an R2 value of 0.89 for the five archaea-euryarchaeota thermophiles (and 0.74 for the entire set of N = 9), although computer simulation shows little correlation. The highest correlation (positive) was found to be between the fractal dimension and di-nucleotide Shannon entropy. However Shannon entropy and sequence GC content were observed to correlate with optimal growth temperature having an R2 of 0.8 (negative), and 0.88 (positive), respectively, for the entire set of 9 thermophiles; thus the correlation lacks species specificity. Together with another correlation study of bacterial radiation dosage with RecA repair gene sequence fractal dimension, it is postulated that fractal dimension analysis is a sensitive tool for studying the relationship between genotype and phenotype among closely related sequences.
Abstract: This study proposes a novel recommender system to
provide the advertisements of context-aware services. Our proposed
model is designed to apply a modified collaborative filtering (CF)
algorithm with regard to the several dimensions for the personalization
of mobile devices – location, time and the user-s needs type. In
particular, we employ a classification rule to understand user-s needs
type using a decision tree algorithm. In addition, we collect primary
data from the mobile phone users and apply them to the proposed
model to validate its effectiveness. Experimental results show that the
proposed system makes more accurate and satisfactory advertisements
than comparative systems.
Abstract: In this paper, we will implement three-dimensional pursuit guidance law with feedback linearization control method and study the effects of parameters. First, we introduce guidance laws and equations of motion of a missile. Pursuit guidance law is our highlight. We apply feedback linearization control method to obtain the accelerations to implement pursuit guidance law. The solution makes warhead direction follow with line-of-sight. Final, the simulation results show that the exact solution derived in this paper is correct and some factors e.g. control gain, time delay, are important to implement pursuit guidance law.
Abstract: This paper analyses the unsteady, two-dimensional
stagnation point flow of an incompressible viscous fluid over a flat
sheet when the flow is started impulsively from rest and at the same
time, the sheet is suddenly stretched in its own plane with a velocity
proportional to the distance from the stagnation point. The partial
differential equations governing the laminar boundary layer forced
convection flow are non-dimensionalised using semi-similar
transformations and then solved numerically using an implicit finitedifference
scheme known as the Keller-box method. Results
pertaining to the flow and heat transfer characteristics are computed
for all dimensionless time, uniformly valid in the whole spatial region
without any numerical difficulties. Analytical solutions are also
obtained for both small and large times, respectively representing the
initial unsteady and final steady state flow and heat transfer.
Numerical results indicate that the velocity ratio parameter is found
to have a significant effect on skin friction and heat transfer rate at
the surface. Furthermore, it is exposed that there is a smooth
transition from the initial unsteady state flow (small time solution) to
the final steady state (large time solution).
Abstract: We numerically study the three-dimensional
magnetohydrodynamics (MHD) stability of oscillatory natural
convection flow in a rectangular cavity, with free top surface, filled
with a liquid metal, having an aspect ratio equal to A=L/H=5, and
subjected to a transversal temperature gradient and a uniform
magnetic field oriented in x and z directions. The finite volume
method was used in order to solve the equations of continuity,
momentum, energy, and potential. The stability diagram obtained in
this study highlights the dependence of the critical value of the
Grashof number Grcrit , with the increase of the Hartmann number
Ha for two orientations of the magnetic field. This study confirms
the possibility of stabilization of a liquid metal flow in natural
convection by application of a magnetic field and shows that the
flow stability is more important when the direction of magnetic field
is longitudinal than when the direction is transversal.
Abstract: Recognizing behavioral patterns of financial markets
is essential for traders. Japanese candlestick chart is a common tool to
visualize and analyze such patterns in an economic time series. Since
the world was introduced to Japanese candlestick charting, traders
saw how combining this tool with intelligent technical approaches
creates a powerful formula for the savvy investors.
This paper propose a generalization to box counting method of
Grassberger-Procaccia, which is based on computing the correlation
dimension of Japanese candlesticks instead commonly used 'close'
points. The results of this method applied on several foreign
exchange rates vs. IRR (Iranian Rial). Satisfactorily show lower
chaotic dimension of Japanese candlesticks series than regular
Grassberger-Procaccia method applied merely on close points of
these same candles. This means there is some valuable information
inside candlesticks.