Abstract: Durability of Membrane Electrode Assembly for
Proton Exchange Membrane Fuel Cells was evaluated in both steady
state and accelerated decay modes. Steady state mode was carried out
at constant current of 800mA/cm2 for 2500 hours using air as cathode
feed and pure hydrogen as anode feed. The degradation of the cell
voltage was 0.015V after such 2500 hrs operation. The degradation
rate was therefore calculated to be 6uV/hr. Continuously Vigorous
fluctuation of the cell voltage, which was switched between OCV and
0.2V, was employed for the accelerated decay mode. No obvious
change in performance of the MEA was observed after 10000 cycles
of such operation.
Abstract: The new era of digital communication has brought up
many challenges that network operators need to overcome. The high
demand of mobile data rates require improved networks, which is a
challenge for the operators in terms of maintaining the quality of
experience (QoE) for their consumers. In live video transmission,
there is a sheer need for live surveillance of the videos in order to
maintain the quality of the network. For this purpose objective
algorithms are employed to monitor the quality of the videos that are
transmitted over a network. In order to test these objective algorithms,
subjective quality assessment of the streamed videos is required, as the
human eye is the best source of perceptual assessment. In this paper we
have conducted subjective evaluation of videos with varying spatial
and temporal impairments. These videos were impaired with frame
freezing distortions so that the impact of frame freezing on the quality
of experience could be studied. We present subjective Mean Opinion
Score (MOS) for these videos that can be used for fine tuning the
objective algorithms for video quality assessment.
Abstract: The aim of this research is to clarify the difference by
industry segment or product characteristics as regards organisation
management for an open innovation to raise R&D performance. In
particular, the trait of the pharmaceutical industry is defined in
comparison with IT component industry segment. In considering open
innovation, both inter-organisational relation and the management in
an organisation are important issues. As methodology, a questionnaire
was conducted. In conclusion, suitable organisation management
according to the difference in industry segment or product
characteristics became clear.
Abstract: Dynamics of a rotor supported by air bearings is
strongly depends on the pressure distribution between the rotor and
the bearing. In this study, internal pressure in air bearings is
numerical and experimental analyzed for different radial clearances.
Firstly the pressure distribution between rotor and bearing is modeled
using Reynold's equation and this model is solved numerically. The
rotor-bearing system is also modeled in four degree of freedom and it
is simulated for different radial clearances. Then, in order to validate
numerical results, a test rig is designed and the rotor bearing system
is run under the same operational conditions. Pressure signals of left
and right bearings are recorded. Internal pressure variations are
compared for numerical and experimental results for different radial
clearances.
Abstract: This paper describes the main features of a knowledge-based system evaluation method. System evaluation is placed in the context of a hybrid legal decision-support system, Advisory Support for Home Settlement in Divorce (ASHSD). Legal knowledge for ASHSD is represented in two forms, as rules and previously decided cases. Besides distinguishing the two different forms of knowledge representation, the paper outlines the actual use of these forms in a computational framework that is designed to generate a plausible solution for a given case, by using rule-based reasoning (RBR) and case-based reasoning (CBR) in an integrated environment. The nature of suitability assessment of a solution has been considered as a multiple criteria decision-making process in ASHAD evaluation. The evaluation was performed by a combination of discussions and questionnaires with different user groups. The answers to questionnaires used in this evaluations method have been measured as a fuzzy linguistic term. The finding suggests that fuzzy linguistic evaluation is practical and meaningful in knowledge-based system development purpose.
Abstract: The Figaro AM-1 sensor module which employs TGS
2600 model gas sensor in air quality assessment was used. The
system was coupled with a microprocessor that enables sensor
module to create warning message via telephone. This low cot sensor
system’s performance was compared with a DiagNose II commercial
electronic nose system. Both air quality sensor and electronic nose
system employ metal oxide chemical gas sensors. In the study
experimental setup, data acquisition methods for electronic nose
system, and performance of the low cost air quality system were
evaluated and explained.
Abstract: Biodiesel, as an alternative renewable fuel, has been
receiving increasing attention due to the limited supply of fossil fuels
and the increasing need for energy. Microalgae are promising source
for lipids, which can be converted to biodiesel. The biodiesel
production from microalgae lipids using lipase catalyzed reaction in
supercritical CO2 medium has several advantages over conventional
production processes. However, identifying the optimum microalgae
lipid extraction and transesterification conditions is still a challenge.
In this study, the quality of biodiesel produced from lipids extracted
from Scenedesmus sp. and their enzymatic transesterification using
supercritical carbon dioxide have been investigated. At the optimum
conditions, the highest biodiesel production yield was found to be
82%. The fuel properties of the produced biodiesel, without any
separation step, at optimum reaction condition, were determined and
compared to ASTM standards. The properties were found to comply
with the limits, and showed a low glycerol content, without any
separation step.
Abstract: The legality of some countries or agencies’ acts to spy
on personal phone calls of the public became a hot topic to many
social groups’ talks. It is believed that this act is considered an
invasion to someone’s privacy. Such act may be justified if it is
singling out specific cases but to spy without limits is very
unacceptable. This paper discusses the needs for not only a simple
and light weight technique to secure mobile voice calls but also a
technique that is independent from any encryption standard or library.
It then presents and tests one encrypting algorithm that is based of
Frequency scrambling technique to show fair and delay-free process
that can be used to protect phone calls from such spying acts.
Abstract: Adopting Most Advantageous Tender (MAT) for the
government procurement projects has become popular in Taiwan. As
time pass by, the problems of MAT has appeared gradually. People
condemn two points that are the result might be manipulated by a
single committee member’s partiality and how to make a fair decision
when the winner has two or more. Arrow’s Impossibility Theorem
proposed that the best scoring method should meet the four reasonable
criteria. According to these four criteria this paper constructed an
“Illegitimate Scores Checking Scheme” for a scoring method and used
the scheme to find out the illegitimate of the current evaluation method
of MAT. This paper also proposed a new scoring method that is called
the “Standardizing Overall Evaluated Score Method”. This method
makes each committee member’s influence tend to be identical. Thus,
the committee members can scoring freely according to their partiality
without losing the fairness. Finally, it was examined by a large-scale
simulation, and the experiment revealed that the it improved the
problem of dictatorship and perfectly avoided the situation of cyclical
majorities, simultaneously. This result verified that the Standardizing
Overall Evaluated Score Method is better than any current evaluation
method of MAT.
Abstract: Tuberculosis (TB) remains a leading cause of
infectious mortality. It is primarily transmitted by the respiratory
route, individuals with active disease may infect others through
airborne particles which releases when they cough, talk, or sing and
subsequently inhale by others. In order to study the effect of the
Bacilli Calmette-Guerin (BCG) vaccine after vaccination of TB
patient, a Vaccinated Susceptible Infected and Recovered (VSIR)
mathematical model is being developed to achieve the desired
objectives. The mathematical model, so developed, shall be used to
quantify the effect of BCG Vaccine to protect the immigrant young
adult person. Moreover, equations are to be established for the
disease endemic and free equilibrium states and subsequently utilized
in disease stability analysis. The stability analysis will give a
complete picture of disease annihilation from the total population if
the total removal rate from the infectious group should be greater
than total number of dormant infections produced throughout
infectious period.
Abstract: Riveting process is one of the important ways to keep
fastening the lap joints in aircraft structures. Failure of aircraft lap
joints directly depends on the stress field in the joint. An important
application of riveting process is in the construction of aircraft
fuselage structures. In this paper, a 3D finite element method is
carried out in order to optimize residual stress field in a riveted lap
joint and also to estimate its fatigue life. In continue, a number of
experiments are designed and analyzed using design of experiments
(DOE). Then, Taguchi method is used to select an optimized case
between different levels of each factor. Besides that, the factor which
affects the most on residual stress field is investigated. Such
optimized case provides the maximum residual stress field. Fatigue
life of the optimized joint is estimated by Paris-Erdogan law. Stress
intensity factors (SIFs) are calculated using both finite element
analysis and experimental formula. In addition, the effect of residual
stress field, geometry and secondary bending are considered in SIF
calculation. A good agreement is found between results of such
methods. Comparison between optimized fatigue life and fatigue life
of other joints has shown an improvement in the joint’s life.
Abstract: Experimental investigations of the DC electric field effect on thermal decomposition of biomass, formation of the axial flow of volatiles (CO, H2, CxHy), mixing of volatiles with swirling airflow at low swirl intensity (S ≈ 0.2-0.35), their ignition and on formation of combustion dynamics are carried out with the aim to understand the mechanism of electric field influence on biomass gasification, combustion of volatiles and heat energy production. The DC electric field effect on combustion dynamics was studied by varying the positive bias voltage of the central electrode from 0.6 kV to 3 kV, whereas the ion current was limited to 2 mA. The results of experimental investigations confirm the field-enhanced biomass gasification with enhanced release of volatiles and the development of endothermic processes at the primary stage of thermochemical conversion of biomass determining the field-enhanced heat energy consumption with the correlating decrease of the flame temperature and heat energy production at this stage of flame formation. Further, the field-enhanced radial expansion of the flame reaction zone correlates with a more complete combustion of volatiles increasing the combustion efficiency by 3% and decreasing the mass fraction of CO, H2 and CxHy in the products, whereas by 10% increases the average volume fraction of CO2 and the heat energy production downstream the combustor increases by 5-10%
Abstract: Total Quality Management (TQM) refers to management methods used to enhance quality and productivity in business organizations. Total Quality Management (TQM) has become a frequently used term in discussions concerning quality. Total Quality management has brought rise in demands on the organizations policy and the customers have gained more importance in the organizations focus. TQM is considered as an important management tool, which helps the organizations to satisfy their customers. In present research critical success factors includes management commitment, customer satisfaction, continuous improvement, work culture and environment, supplier quality management, training and development, employee satisfaction and product/process design are studied. A questionnaire is developed to implement these critical success factors in implementation of total quality management in Indian industry. Questionnaires filled by consulting different industrial organizations. Data collected from questionnaires is analyzed by descriptive and importance indexes.
Abstract: The modeling lung respiratory system that has complex anatomy and biophysics presents several challenges including tissue-driven flow patterns and wall motion. Also, the pulmonary lung system because of that they stretch and recoil with each breath, has not static walls and structures. The direct relationship between air flow and tissue motion in the lung structures naturally prefers an FSI simulation technique. Therefore, in order to toward the realistic simulation of pulmonary breathing mechanics the development of a coupled FSI computational model is an important step. A simple but physiologically relevant three-dimensional deep long geometry is designed and fluid-structure interaction (FSI) coupling technique is utilized for simulating the deformation of the lung parenchyma tissue that produces airflow fields. The real understanding of respiratory tissue system as a complex phenomenon have been investigated with respect to respiratory patterns, fluid dynamics and tissue viscoelasticity and tidal breathing period.
Abstract: Many interventions for social skills acquisition aim to decrease the gap between social skills deficits in the individual and normative social skills; nevertheless little is known of typical social skills according to age difference in students. In this study, we developed new quintet of Hokkaido Social Skills Inventory (HSSI) to identify age-appropriate social skills for school adaptation. First, we selected 13 categories of social skills for school adaptation from previous studies, and created questionnaire items through discussion by 25 teachers in all three levels from elementary schools to senior high schools. Second, the factor structures of five versions of the social skills scale were investigated on 2nd grade (n = 1,864), 4th grade (n = 1,936), 6th grade (n = 2,085), 7th grade (n = 2,007), and 10th grade (n = 912) students, respectively. The exploratory factor analysis showed that a number of constructing factors of social skills increased as one’s grade in school advanced. The results in the present study can be useful to characterize the age-appropriate social skills for school adaptation.
Abstract: The main objective of this study was to assess the
annual concentration and seasonal variation of benzo(a)pyrene (BaP)
associated with PM10 in an urban site of Győr and in a rural site of
Sarród in the sampling period of 2008–2012. A total of 280 PM10
aerosol samples were collected in each sampling site and analyzed for
BaP by gas chromatography method. The BaP concentrations ranged
from undetected to 8 ng/m3 with the mean value of 1.01 ng/m3 in the
sampling site of Győr, and from undetected to 4.07 ng/m3 with the
mean value of 0.52 ng/m3 in the sampling site of Sarród, respectively.
Relatively higher concentrations of BaP were detected in samples
collected in both sampling sites in the heating seasons compared with
non-heating periods. The annual mean BaP concentrations were
comparable with the published data of different other Hungarian
sites.
Abstract: In recent years, there has been a decline in physical
activity among adults. Motivation has been shown to be a crucial
factor in maintaining physical activity. The purpose of this study was
to whether PA motives measured by the Physical Activity and
Leisure Motivation Scale PALMS predicted the actual amount of PA
at a later time to provide evidence for the construct validity of the
PALMS. A quantitative, cross-sectional descriptive research design
was employed. The Demographic Form, PALMS, and International
Physical Activity Questionnaire Short form (IPAQ-S) questionnaires
were used to assess motives and amount for physical activity in
adults on two occasions. A sample of 489 male undergraduate
students aged 18 to 25 years (mean ±SD; 22.30±8.13 years) took part
in the study. Participants were divided into three types of activities,
namely exercise, racquet sport, and team sports and female
participants only took part in one type of activity, namely team
sports. After 14 weeks, all 489 undergraduate students who had filled
in the initial questionnaire (Occasion 1) received the questionnaire
via email (Occasion 2). Of the 489 students, 378 males emailed back
the completed questionnaire. The results showed that not only were
pertinent sub-scales of PALMS positively related to amount of
physical activity, but separate regression analyses showed the
positive predictive effect of PALMS motives for amount of physical
activity for each type of physical activity among participants. This
study supported the construct validity of the PALMS by showing that
the motives measured by PALMS did predict amount of PA. This
information can be obtained to match people with specific sport or
activity which in turn could potentially promote longer adherence to
the specific activity.
Abstract: Designing cost-efficient, secure network protocols for
Wireless Sensor Networks (WSNs) is a challenging problem because
sensors are resource-limited wireless devices. Security services such
as authentication and improved pairwise key establishment are
critical to high efficient networks with sensor nodes. For sensor
nodes to correspond securely with each other efficiently, usage of
cryptographic techniques is necessary. In this paper, two key
predistribution schemes that enable a mobile sink to establish a
secure data-communication link, on the fly, with any sensor nodes.
The intermediate nodes along the path to the sink are able to verify
the authenticity and integrity of the incoming packets using a
predicted value of the key generated by the sender’s essential power.
The proposed schemes are based on the pairwise key with the mobile
sink, our analytical results clearly show that our schemes perform
better in terms of network resilience to node capture than existing
schemes if used in wireless sensor networks with mobile sinks.
Abstract: The purpose of the study was to find out the effects of
Aquatic and Land plyometric training on selected physical variables
in intercollegiate male handball players. To achieve this purpose of
the study, forty five handball players of Sardar Vallabhbhai National
Institute of Technology, Surat, Gujarat were selected as players at
random and their age ranged between 18 to 21 years. The selected
players were divided into three equal groups of fifteen players each.
Group I underwent Aquatic plyometric training, Group II underwent
Land plyometric training and Group III Control group for three days
per week for twelve weeks. Control Group did not participate in any
special training programme apart from their regular activities as per
their curriculum. The following physical fitness variables namely
speed; leg explosive power and agility were selected as dependent
variables. All the players of three groups were tested on selected
dependent variables prior to and immediately after the training
programme. The analysis of covariance was used to analyze the
significant difference, if any among the groups. Since, three groups
were compared, whenever the obtained ‘F’ ratio for adjusted posttest
was found to be significant, the Scheffe’s test to find out the paired
mean differences, if any. The 0.05 level of confidence was fixed as
the level of significance to test the ‘F’ ratio obtained by the analysis
of covariance, which was considered as an appropriate. The result of
the study indicates due to Aquatic and Land plyometric training on
speed, explosive power, and agility has been improved significantly.
Abstract: This study addresses a concept of the Sustainable Building Environmental Model (SBEM) developed to optimize energy consumption in air conditioning and ventilation (ACV) systems without any deterioration of indoor environmental quality (IEQ). The SBEM incorporates two main components: an adaptive comfort temperature control module (ACT) and a new carbon dioxide demand control module (nDCV). These two modules take an innovative approach to maintain satisfaction of the Indoor Environmental Quality (IEQ) with optimum energy consumption; they provide a rational basis of effective control. A total of 2133 sets of measurement data of indoor air temperature (Ta), relative humidity (Rh) and carbon dioxide concentration (CO2) were conducted in some Hong Kong offices to investigate the potential of integrating the SBEM. A simulation was used to evaluate the dynamic performance of the energy and air conditioning system with the integration of the SBEM in an air-conditioned building. It allows us make a clear picture of the control strategies and performed any pre-tuned of controllers before utilized in real systems. With the integration of SBEM, it was able to save up to 12.3% in simulation of overall electricity consumption, and maintain the average carbon dioxide concentration within 1000ppm and occupant dissatisfaction in 20%.