Abstract: Using a force balanced translational-radial dynamics,
phase space of the moving single bubble sonoluminescence (m-
SBSL) in 85% wt sulfuric acid has been numerically calculated. This
phase space is compared with that of single bubble sonoluminescence
(SBSL) in pure water which has been calculated by using the mere
radial dynamics. It is shown that in 85% wt sulfuric acid, in a general
agreement with experiment, the bubble-s positional instability
threshold lays under the shape instability threshold. At the onset of
spatial instability of moving sonoluminescing (SL) bubble in 85%
wt sulfuric acid, temporal effects of the hydrodynamic force on the
bubble translational-radial dynamics have been investigated. The
appearance of non-zero history force on the moving SL bubble is
because of proper condition which was produced by high viscosity of
acid. Around the moving bubble collapse due to the rapid contraction
of the bubble wall, the inertial based added mass force overcomes the
viscous based history force and induces acceleration on the bubble
translational motion.
Abstract: The whole work is based on possibility to use Lego Mindstorms robotics systems to reduce costs. Lego Mindstorms consists of a wide variety of hardware components necessary to simulate, programme and test of robotics systems in practice. To programme algorithm, which simulates space using the ultrasonic sensor, was used development environment supplied with kit. Software Matlab was used to render values afterwards they were measured by ultrasonic sensor. The algorithm created for this paper uses theoretical knowledge from area of signal processing. Data being processed by algorithm are collected by ultrasonic sensor that scans 2D space in front of it. Ultrasonic sensor is placed on moving arm of robot which provides horizontal moving of sensor. Vertical movement of sensor is provided by wheel drive. The robot follows map in order to get correct positioning of measured data. Based on discovered facts it is possible to consider Lego Mindstorm for low-cost and capable kit for real-time modelling.
Abstract: An international cooperation between educators in
Australia and the US has led to a reconceptualization of the teaching
of a library science course at Appalachian State University. The
pedagogy of Action Learning coupled with a 3D virtual learning
environment immerses students in a social constructivist learning
space that incorporates and supports interaction and reflection. The
intent of this study was to build a bridge between theory and practice
by providing students with a tool set that promoted personal and
social reflection, and created and scaffolded a community of practice.
Besides, action learning is an educational process whereby the fifty
graduate students experienced their own actions and experience to
improve performance.
Abstract: A complex valued neural network is a neural network, which consists of complex valued input and/or weights and/or thresholds and/or activation functions. Complex-valued neural networks have been widening the scope of applications not only in electronics and informatics, but also in social systems. One of the most important applications of the complex valued neural network is in image and vision processing. In Neural networks, radial basis functions are often used for interpolation in multidimensional space. A Radial Basis function is a function, which has built into it a distance criterion with respect to a centre. Radial basis functions have often been applied in the area of neural networks where they may be used as a replacement for the sigmoid hidden layer transfer characteristic in multi-layer perceptron. This paper aims to present exhaustive results of using RBF units in a complex-valued neural network model that uses the back-propagation algorithm (called 'Complex-BP') for learning. Our experiments results demonstrate the effectiveness of a Radial basis function in a complex valued neural network in image recognition over a real valued neural network. We have studied and stated various observations like effect of learning rates, ranges of the initial weights randomly selected, error functions used and number of iterations for the convergence of error on a neural network model with RBF units. Some inherent properties of this complex back propagation algorithm are also studied and discussed.
Abstract: Genetic algorithms (GAs) have been widely used for
global optimization problems. The GA performance depends highly
on the choice of the search space for each parameter to be optimized.
Often, this choice is a problem-based experience. The search space
being a set of potential solutions may contain the global optimum
and/or other local optimums. A bad choice of this search space
results in poor solutions. In this paper, our approach consists in
extending the search space boundaries during the GA optimization,
only when it is required. This leads to more diversification of GA
population by new solutions that were not available with fixed search
space boundaries. So, these dynamic search spaces can improve the
GA optimization performances. The proposed approach is applied to
power system stabilizer optimization for multimachine power system
(16-generator and 68-bus). The obtained results are evaluated and
compared with those obtained by ordinary GAs. Eigenvalue analysis
and nonlinear system simulation results show the effectiveness of the
proposed approach to damp out the electromechanical oscillation and
enhance the global system stability.
Abstract: This paper invites to dialogue and reflections on
innovation and entrepreneurship by presenting concepts of innovation
leading to the introduction of a complex theoretical framework;
Cooperative Innovation (CO-IN). CO-IN is a didactic model
enhancing and scaffolding processes of cooperation creating
innovation drawing on a Scandinavian tradition.
CO-IN is based on a cross-sectorial and multidisciplinary
approach. We introduce the concept of complementarity to help
capture the validity of diversity and we suggest the concept of “the
space in between" to understand the creation of identity as a
collective mind. We see dialogue and the use of multi modal
techniques as essential tools for conceptualizations giving possibility
for clarification of the complexity and diversity leading to decision
making based on knowledge as commons.
We introduce the didactic design and present our empirical
findings from an innovation workshop in Argentina. In a final
paragraph we reflect on the design as a support of the development of
common ground, collective mind and collective action and the
creation of knowledge as commons to facilitate innovation and
entrepreneurship.
Abstract: This paper describes the development of a WLAN
propagation model, using Spectral Analyzer measurements. The
signal is generated by two Access Points (APs) on the base floor at
the administrative Communication School of ESPOL building. In
general, users do not have a Q&S reference about a wireless network;
however, this depends on the level signal as a function of frequency,
distance and other path conditions between receiver and transmitter.
Then, power density of the signal decrease as it propagates through
space and data transfer rate is affected. This document evaluates and
implements empirical mathematical formulation for the
characterization of WLAN radio wave propagation on two aisles of
the building base floor.
Abstract: This paper proposes a solution to the motion planning
and control problem of car-like mobile robots which is required to
move safely to a designated target in a priori known workspace
cluttered with swarm of boids exhibiting collective emergent
behaviors. A generalized algorithm for target convergence and
swarm avoidance is proposed that will work for any number of
swarms. The control laws proposed in this paper also ensures
practical stability of the system. The effectiveness of the proposed
control laws are demonstrated via computer simulations of an
emergent behavior.
Abstract: The objective of the paper is twofold. First, to develop a
formal framework for planning for mobile agents. A logical language
based on a temporal logic is proposed that can express a type of
tasks which often arise in network management. Second, to design a
planning algorithm for such tasks. The aim of this paper is to study
the importance of finding plans for mobile agents. Although there
has been a lot of research in mobile agents, not much work has been
done to incorporate planning ideas for such agents. This paper makes
an attempt in this direction. A theoretical study of finding plans for
mobile agents is undertaken. A planning algorithm (based on the
paradigm of mobile computing) is proposed and its space, time, and
communication complexity is analyzed. The algorithm is illustrated
by working out an example in detail.
Abstract: Clustering algorithms are attractive for the task of class identification in spatial databases. However, the application to large spatial databases rises the following requirements for clustering algorithms: minimal requirements of domain knowledge to determine the input parameters, discovery of clusters with arbitrary shape and good efficiency on large databases. The well-known clustering algorithms offer no solution to the combination of these requirements. In this paper, a density based clustering algorithm (DCBRD) is presented, relying on a knowledge acquired from the data by dividing the data space into overlapped regions. The proposed algorithm discovers arbitrary shaped clusters, requires no input parameters and uses the same definitions of DBSCAN algorithm. We performed an experimental evaluation of the effectiveness and efficiency of it, and compared this results with that of DBSCAN. The results of our experiments demonstrate that the proposed algorithm is significantly efficient in discovering clusters of arbitrary shape and size.
Abstract: The quality of a machined surface is becoming more and more important to justify the increasing demands of sophisticated component performance, longevity, and reliability. Usually, any machining operation leaves its own characteristic evidence on the machined surface in the form of finely spaced micro irregularities (surface roughness) left by the associated indeterministic characteristics of the different elements of the system: tool-machineworkpart- cutting parameters. However, one of the most influential sources in machining affecting surface roughness is the instantaneous state of tool edge. The main objective of the current work is to relate the in-process immeasurable cutting edge deformation and surface roughness to a more reliable easy-to-measure force signals using a robust non-linear time-dependent modeling regression techniques. Time-dependent modeling is beneficial when modern machining systems, such as adaptive control techniques are considered, where the state of the machined surface and the health of the cutting edge are monitored, assessed and controlled online using realtime information provided by the variability encountered in the measured force signals. Correlation between wear propagation and roughness variation is developed throughout the different edge lifetimes. The surface roughness is further evaluated in the light of the variation in both the static and the dynamic force signals. Consistent correlation is found between surface roughness variation and tool wear progress within its initial and constant regions. At the first few seconds of cutting, expected and well known trend of the effect of the cutting parameters is observed. Surface roughness is positively influenced by the level of the feed rate and negatively by the cutting speed. As cutting continues, roughness is affected, to different extents, by the rather localized wear modes either on the tool nose or on its flank areas. Moreover, it seems that roughness varies as wear attitude transfers from one mode to another and, in general, it is shown that it is improved as wear increases but with possible corresponding workpart dimensional inaccuracy. The dynamic force signals are found reasonably sensitive to simulate either the progressive or the random modes of tool edge deformation. While the frictional force components, feeding and radial, are found informative regarding progressive wear modes, the vertical (power) components is found more representative carrier to system instability resulting from the edge-s random deformation.
Abstract: In designing river intakes and diversion structures, it is paramount that the sediments entering the intake are minimized or, if possible, completely separated. Due to high water velocity, sediments can significantly damage hydraulic structures especially when mechanical equipment like pumps and turbines are used. This subsequently results in wasting water, electricity and further costs. Therefore, it is prudent to investigate and analyze the performance of lateral intakes affected by sediment control structures. Laboratory experiments, despite their vast potential and benefits, can face certain limitations and challenges. Some of these include: limitations in equipment and facilities, space constraints, equipment errors including lack of adequate precision or mal-operation, and finally, human error. Research has shown that in order to achieve the ultimate goal of intake structure design – which is to design longlasting and proficient structures – the best combination of sediment control structures (such as sill and submerged vanes) along with parameters that increase their performance (such as diversion angle and location) should be determined. Cost, difficulty of execution and environmental impacts should also be included in evaluating the optimal design. This solution can then be applied to similar problems in the future. Subsequently, the model used to arrive at the optimal design requires high level of accuracy and precision in order to avoid improper design and execution of projects. Process of creating and executing the design should be as comprehensive and applicable as possible. Therefore, it is important that influential parameters and vital criteria is fully understood and applied at all stages of choosing the optimal design. In this article, influential parameters on optimal performance of the intake, advantages and disadvantages, and efficiency of a given design are studied. Then, a multi-criterion decision matrix is utilized to choose the optimal model that can be used to determine the proper parameters in constructing the intake.
Abstract: As a matter of the fact that online social networks like
Twitter, Facebook and MySpace have experienced an extensive
growth in recent years. Social media offers individuals with a tool for
communicating and interacting with one another. These social
networks enable people to stay in touch with other people and
express themselves. This process makes the users of online social
networks active creators of content rather than being only consumers
of traditional media. That’s why millions of people show strong
desire to learn the methods and tools of digital content production
and necessary communication skills. However, the booming interest
in communication and interaction through online social networks and
high level of eagerness to invent and implement the ways to
participate in content production raise some privacy and security
concerns.
This presentation aims to open the assumed revolutionary,
democratic and liberating nature of the online social media up for
discussion by reviewing some recent political developments in
Turkey. Firstly, the role of Internet and online social networks in
mobilizing collective movements through social interactions and
communications will be questioned. Secondly, some cases from Gezi
and Okmeydanı Protests and also December 17-25 period will be
presented in order to illustrate misinformation and manipulation in
social media and violation of individual privacy through online social
networks in order to damage social unity and stability contradictory
to democratic nature of online social networking.
Abstract: In this paper we present a new approach to detecting a
flaw in T.O.F.D (Time Of Flight Diffraction) type ultrasonic image
based on texture features. Texture is one of the most important
features used in recognizing patterns in an image. The paper
describes texture features based on 2D Gabor functions, i.e.,
Gaussian shaped band-pass filters, with dyadic treatment of the radial
spatial frequency range and multiple orientations, which represent an
appropriate choice for tasks requiring simultaneous measurement in
both space and frequency domains. The most relevant features are
used as input data on a Fuzzy c-mean clustering classifier. The
classes that exist are only two: 'defects' or 'no defects'. The proposed
approach is tested on the T.O.F.D image achieved at the laboratory
and on the industrial field.
Abstract: An implementation of current-mode multiphase sinusoidal oscillators is presented. Using CFTA-based lossy integrators, odd and odd/even phase systems can be realized with following advantages. The condition of oscillation and frequency of oscillation can be orthogonally tuned. The high output impedances facilitate easy driving an external load without additional current buffers. The proposed MSOs provide odd or even phase signals that are equally spaced in phase and equal amplitude. The circuit requires one CFTA, one resistor and one grounded capacitor per phase without additional current amplifier. The results of PSPICE simulations using CMOS CFTA are included to verify theory.
Abstract: In this paper, we propose a new image segmentation approach for colour textured images. The proposed method for image segmentation consists of two stages. In the first stage, textural features using gray level co-occurrence matrix(GLCM) are computed for regions of interest (ROI) considered for each class. ROI acts as ground truth for the classes. Ohta model (I1, I2, I3) is the colour model used for segmentation. Statistical mean feature at certain inter pixel distance (IPD) of I2 component was considered to be the optimized textural feature for further segmentation. In the second stage, the feature matrix obtained is assumed to be the degraded version of the image labels and modeled as Markov Random Field (MRF) model to model the unknown image labels. The labels are estimated through maximum a posteriori (MAP) estimation criterion using ICM algorithm. The performance of the proposed approach is compared with that of the existing schemes, JSEG and another scheme which uses GLCM and MRF in RGB colour space. The proposed method is found to be outperforming the existing ones in terms of segmentation accuracy with acceptable rate of convergence. The results are validated with synthetic and real textured images.
Abstract: This study explores how the mechanics of learning
paves the way to engineering innovation. Theories related to learning
in the new product/service innovation are reviewed from an
organizational perspective, behavioral perspective, and engineering
perspective. From this, an engineering team-s external interactions
for knowledge brokering and internal composition for skill balance
are examined from a learning and innovation viewpoints. As a result,
an integrated learning model is developed by reconciling the
theoretical perspectives as well as developing propositions that
emphasize the centrality of learning, and its drivers, in the
engineering product/service development. The paper also provides a
review and partial validation of the propositions using the results of a
previously published field study in the aerospace industry.
Abstract: BioEnergy is an archetypal appropriate technology
and alternate source of energy in rural areas of China, and can meet
the basic need for cooking fuel in rural areas. The paper introduces
with an alternate mean of research that can accelerate the biogas
energy production. Tithonia diversifolia or the Tree marigold can be
hailed as mesophillic anaerobic digestion to increase the production
of more Bioenergy. Tithonia diversifolia is very native to Mexico and
Central America, which can be served as ornamental plants- green
manure and can prevent soil erosion. Tithonia diversifolia is widely
grown and known to Asia, Africa, America and Australia as well.
Nowadays, Considering China’s geographical condition it is found
that Tithonia diversifolia is widely growing plant in the many tropical
and subtropical regions of southern Yunnan- which can have great
usage in accelerating and increasing the Bioenergy production
technology. The paper discussed aiming at proving possibility that
Tithonia diversifolia can be applied in biogas fermentation and its
biogas production potential, the research carried experiment on
Tithonia diversifolia biogas fermentation under the mesophilic
condition (35 Celsius Degree). The result revealed that Tithonia
diversifolia can be used as biogas fermentative material, and 6%
concentration can get the best biogas production, with the TS biogas
production rate 656mL/g and VS biogas production rate 801mL/g. It
is well addressed that Tithonia diversifolia grows wildly in 53
Counties and 9 cities of Yunnan Province, which mainly grows in
form of the road side plants, the edge of the field, countryside, forest
edge, open space; of which demersum-natures can form dense
monospecific beds -causing serious harm to agricultural production
landforms threatening the ecological system as a potentially harmful
exotic plant. There are also found the three types of invasive daisy
alien plants -Eupatorium adenophorum, Eupatorium Odorata and
Tithonia diversifolia in Yunnan Province of China-among them the
Tithonia diversifolia is responsible for causing serious harm to
agricultural production. In this paper we have designed the
experimental explanation of Biogas energy production that requires
anaerobic environment and some microbes; Tithonia diversifolia
plant has been taken into consideration while carrying experiments
and with successful resulting of generating more BioEnergy
emphasizing on the practical applications of Tithonia diversifolia.
This paper aims at- to find a new mechanism to provide a more
scientific basis for the development of this plant herbicides in Biogas
energy and to improve the utilization throughout the world as well.
Abstract: Does the spatial perspective provide a common thread for rural sociology? Have rural sociologists succeeded in bringing order to their data using spatial analysis models and techniques? A trial answer to such questions, as touchstones of theoretical and applied sociological studies in rural areas, is the point at issue in the present paper. Spatial analyses have changed the way rural sociologists approach scientific problems. Rural sociology is spatial by nature because much, if not most, of its research topics has a spatial “awareness." However, such spatial awareness is not quite the same as spatial analysis because it is not typically associated with underlying theories and hypotheses about spatial patterns that are designed to be tested for their specific spatial content. This paper presents pressing issues for future research to reintroduce mainstream rural sociology to the concept of space.
Abstract: In this article an isotropic linear elastic half-space with
a cylindrical cavity of finite length is considered to be under the
effect of a ring shape time-harmonic torsion force applied at an
arbitrary depth on the surface of the cavity. The equation of
equilibrium has been written in a cylindrical coordinate system. By
means of Fourier cosine integral transform, the non-zero
displacement component is obtained in the transformed domain. With
the aid of the inversion theorem of the Fourier cosine integral
transform, the displacement is obtained in the real domain. With the
aid of boundary conditions, the involved boundary value problem for
the fundamental solution is reduced to a generalized Cauchy singular
integral equation. Integral representation of the stress and
displacement are obtained, and it is shown that their degenerated
form to the static problem coincides with existing solutions in the
literature.