Abstract: The paper discusses the results obtained to predict
reinforcement in singly reinforced beam using Neural Net (NN),
Support Vector Machines (SVM-s) and Tree Based Models. Major
advantage of SVM-s over NN is of minimizing a bound on the
generalization error of model rather than minimizing a bound on
mean square error over the data set as done in NN. Tree Based
approach divides the problem into a small number of sub problems to
reach at a conclusion. Number of data was created for different
parameters of beam to calculate the reinforcement using limit state
method for creation of models and validation. The results from this
study suggest a remarkably good performance of tree based and
SVM-s models. Further, this study found that these two techniques
work well and even better than Neural Network methods. A
comparison of predicted values with actual values suggests a very
good correlation coefficient with all four techniques.
Abstract: Protein structure determination and prediction has
been a focal research subject in the field of bioinformatics due to the
importance of protein structure in understanding the biological and
chemical activities of organisms. The experimental methods used by
biotechnologists to determine the structures of proteins demand
sophisticated equipment and time. A host of computational methods
are developed to predict the location of secondary structure elements
in proteins for complementing or creating insights into experimental
results. However, prediction accuracies of these methods rarely
exceed 70%.
Abstract: The main objectives of this paper are to measure
pollutants concentrations in the oil refinery area in Kuwait over three
periods during one year, obtain recent emission inventory for the
three refineries of Kuwait, use AERMOD and the emission inventory
to predict pollutants concentrations and distribution, compare model
predictions against measured data, and perform numerical
experiments to determine conditions at which emission rates and the
resulting pollutant dispersion is below maximum allowable limits.
Abstract: A theoretical study is conducted to design and explore
the effect of different parameters such as heat loads, the tube size of
piping system, wick thickness, porosity and hole size on the
performance and capability of a Loop Heat Pipe(LHP). This paper
presents a steady state model that describes the different phenomena
inside a LHP. Loop Heat Pipes(LHPs) are two-phase heat transfer
devices with capillary pumping of a working fluid. By their original
design comparing with heat pipes and special properties of the
capillary structure, they-re capable of transferring heat efficiency for
distances up to several meters at any orientation in the gravity field,
or to several meters in a horizontal position. This theoretical model is
described by different relations to satisfy important limits such as
capillary and nucleate boiling. An algorithm is developed to predict
the size of the LHP satisfying the limitations mentioned above for a
wide range of applied loads. Finally, to assess and evaluate the
algorithm and all the relations considered, we have used to design a
new kind of LHP to recover the heat from the exhaust of an actual
Gas Turbine. By finding the results, it showed that we can use the
LHP as a very high efficient device to recover the heat even in high
amount of loads(exhaust of a gas turbine). The sizes of all parts of the
LHP were obtained using the developed algorithm.
Abstract: The present study deals with the modeling and simulation of flow through an annular reactor at different hydrodynamic conditions using computational fluid dynamics (CFD) to investigate the flow behavior. CFD modeling was utilized to predict velocity distribution and average velocity in the annular geometry. The results of CFD simulations were compared with the mathematically derived equations and already developed correlations for validation purposes. CFD modeling was found suitable for predicting the flow characteristics in annular geometry under laminar flow conditions. It was observed that CFD also provides local values of the parameters of interest in addition to the average values for the simulated geometry.
Abstract: This paper examines the use of mechanical aerator for
oxidation-ditch process. The rotor, which controls the aeration, is the
main component of the aeration process. Therefore, the objective of
this study is to find out the variations in overall oxygen transfer
coefficient (KLa) and aeration efficiency (AE) for different
configurations of aerator by varying the parameters viz. speed of
aerator, depth of immersion, blade tip angles so as to yield higher
values of KLa and AE. Six different configurations of aerator were
developed and fabricated in the laboratory and were tested for abovementioned
parameters. The curved blade rotor (CBR) emerged as a
potential aerator with blade tip angle of 47°.
The mathematical models are developed for predicting the
behaviour of CBR w.r.t kLa and power. In laboratory studies, the
optimum value of KLa and AE were observed to be 10.33 h-1 and
2.269 kg O2/ kWh.
Abstract: The simulation of extrusion process is studied widely
in order to both increase products and improve quality, with broad
application in wire coating. The annular tube-tooling extrusion was
set up by a model that is termed as Navier-Stokes equation in
addition to a rheological model of differential form based on singlemode
exponential Phan-Thien/Tanner constitutive equation in a twodimensional
cylindrical coordinate system for predicting the
contraction point of the polymer melt beyond the die. Numerical
solutions are sought through semi-implicit Taylor-Galerkin pressurecorrection
finite element scheme. The investigation was focused on
incompressible creeping flow with long relaxation time in terms of
Weissenberg numbers up to 200. The isothermal case was considered
with surface tension effect on free surface in extrudate flow and no
slip at die wall. The Stream Line Upwind Petrov-Galerkin has been
proposed to stabilize solution. The structure of mesh after die exit
was adjusted following prediction of both top and bottom free
surfaces so as to keep the location of contraction point around one
unit length which is close to experimental results. The simulation of
extrusion process is studied widely in order to both increase products
and improve quality, with broad application in wire coating. The
annular tube-tooling extrusion was set up by a model that is termed
as Navier-Stokes equation in addition to a rheological model of
differential form based on single-mode exponential Phan-
Thien/Tanner constitutive equation in a two-dimensional cylindrical
coordinate system for predicting the contraction point of the polymer
melt beyond the die. Numerical solutions are sought through semiimplicit
Taylor-Galerkin pressure-correction finite element scheme.
The investigation was focused on incompressible creeping flow with
long relaxation time in terms of Weissenberg numbers up to 200. The
isothermal case was considered with surface tension effect on free
surface in extrudate flow and no slip at die wall. The Stream Line
Upwind Petrov-Galerkin has been proposed to stabilize solution. The
structure of mesh after die exit was adjusted following prediction of
both top and bottom free surfaces so as to keep the location of
contraction point around one unit length which is close to
experimental results.
Abstract: A new fast correlation algorithm for calibrating the
wavelength of Optical Spectrum Analyzers (OSAs) was introduced
in [1]. The minima of acetylene gas spectra were measured and
correlated with saved theoretical data [2]. So it is possible to find the
correct wavelength calibration data using a noisy reference spectrum.
First tests showed good algorithmic performance for gas line spectra
with high noise. In this article extensive performance tests were made
to validate the noise resistance of this algorithm. The filter and
correlation parameters of the algorithm were optimized for improved
noise performance. With these parameters the performance of this
wavelength calibration was simulated to predict the resulting
wavelength error in real OSA systems. Long term simulations were
made to evaluate the performance of the algorithm over the lifetime
of a real OSA.
Abstract: This paper addresses the design of predictive
networked controller with adaptation of a communication delay. The
networked control system contains random delays from sensor to
controller and from controller to actuator. The proposed predictive
controller includes an adaptation loop which decreases the influence
of communication delay on the control performance. Also, the
predictive controller contains a filter which improves the robustness
of the control system. The performance of the proposed adaptive
predictive controller is demonstrated by simulation results in
comparison with PI controller and predictive controller with constant
delay.
Abstract: Diabetes Mellitus is a chronic metabolic disorder, where the improper management of the blood glucose level in the diabetic patients will lead to the risk of heart attack, kidney disease and renal failure. This paper attempts to enhance the diagnostic accuracy of the advancing blood glucose levels of the diabetic patients, by combining principal component analysis and wavelet neural network. The proposed system makes separate blood glucose prediction in the morning, afternoon, evening and night intervals, using dataset from one patient covering a period of 77 days. Comparisons of the diagnostic accuracy with other neural network models, which use the same dataset are made. The comparison results showed overall improved accuracy, which indicates the effectiveness of this proposed system.
Abstract: This paper focuses on the data-driven generation
of fuzzy IF...THEN rules. The resulted fuzzy rule base can be
applied to build a classifier, a model used for prediction, or
it can be applied to form a decision support system. Among
the wide range of possible approaches, the decision tree and
the association rule based algorithms are overviewed, and two
new approaches are presented based on the a priori fuzzy
clustering based partitioning of the continuous input variables.
An application study is also presented, where the developed
methods are tested on the well known Wisconsin Breast Cancer
classification problem.
Abstract: With the hardware technology advancing, the cost of
storing is decreasing. Thus there is an urgent need for new techniques
and tools that can intelligently and automatically assist us in
transferring this data into useful knowledge. Different techniques of
data mining are developed which are helpful for handling these large
size databases [7]. Data mining is also finding its role in the field of
biotechnology. Pedigree means the associated ancestry of a crop
variety. Genetic diversity is the variation in the genetic composition
of individuals within or among species. Genetic diversity depends
upon the pedigree information of the varieties. Parents at lower
hierarchic levels have more weightage for predicting genetic
diversity as compared to the upper hierarchic levels. The weightage
decreases as the level increases. For crossbreeding, the two varieties
should be more and more genetically diverse so as to incorporate the
useful characters of the two varieties in the newly developed variety.
This paper discusses the searching and analyzing of different possible
pairs of varieties selected on the basis of morphological characters,
Climatic conditions and Nutrients so as to obtain the most optimal
pair that can produce the required crossbreed variety. An algorithm
was developed to determine the genetic diversity between the
selected wheat varieties. Cluster analysis technique is used for
retrieving the results.
Abstract: This paper proposes method of diagnosing ball screw
preload loss through the Hilbert-Huang Transform （HHT） and
Multiscale entropy （MSE） process. The proposed method can
diagnose ball screw preload loss through vibration signals when the
machine tool is in operation. Maximum dynamic preload of 2 %, 4 %,
and 6 % ball screws were predesigned, manufactured, and tested
experimentally. Signal patterns are discussed and revealed using
Empirical Mode Decomposition（EMD）with the Hilbert Spectrum.
Different preload features are extracted and discriminated using HHT.
The irregularity development of a ball screw with preload loss is
determined and abstracted using MSE based on complexity
perception. Experiment results show that the proposed method can
predict the status of ball screw preload loss. Smart sensing for the
health of the ball screw is also possible based on a comparative
evaluation of MSE by the signal processing and pattern matching of
EMD/HHT. This diagnosis method realizes the purposes of prognostic
effectiveness on knowing the preload loss and utilizing convenience.
Abstract: This paper presents the automated methods employed
for extracting craniofacial landmarks in white light images as part of
a registration framework designed to support three neurosurgical
procedures. The intraoperative space is characterised by white light
stereo imaging while the preoperative plan is performed on CT scans.
The registration aims at aligning these two modalities to provide a
calibrated environment to enable image-guided solutions. The
neurosurgical procedures can then be carried out by mapping the
entry and target points from CT space onto the patient-s space. The
registration basis adopted consists of natural landmarks (eye corner
and ear tragus). A 5mm accuracy is deemed sufficient for these three
procedures and the validity of the selected registration basis in
achieving this accuracy has been assessed by simulation studies. The
registration protocol is briefly described, followed by a presentation
of the automated techniques developed for the extraction of the
craniofacial features and results obtained from tests on the AR and
FERET databases. Since the three targeted neurosurgical procedures
are routinely used for head injury management, the effect of
bruised/swollen faces on the automated algorithms is assessed. A
user-interactive method is proposed to deal with such unpredictable
circumstances.
Abstract: The paper discuses the effect of initial stresses on the reflection coefficients of plane waves in a dissipative medium. Basic governing equations are formulated in context of Biot's incremental deformation theory. These governing equations are solved analytically to obtain the dimensional phase velocities of plane waves propagating in plane of symmetry. Closed-form expressions for the reflection coefficients of P and SV waves- incident at the free surface of an initially stressed dissipative medium are obtained. Numerical computations, using these expressions, are carried out for a particular model. Computations made with the results predicted in presence and absence of the initial stresses and the results have been shown graphically. The study shows that the presence of compressive initial stresses increases the velocity of longitudinal wave (P-wave) but diminishes that of transverse wave (SV-wave). Also the numerical results presented indicate that initial stresses and dissipation might affect the reflection coefficients significantly.
Abstract: The governing differential equations of laminated
plate utilizing trigonometric shear deformation theory are derived
using energy approach. The governing differential equations
discretized by different radial basis functions are used to predict the
free vibration behavior of symmetric laminated composite plates.
Effect of orthotropy and span to thickness ratio on frequency
parameter of simply supported laminated plate is presented.
Numerical results show the accuracy and good convergence of radial
basis functions.
Abstract: Wind is among the potential energy resources which
can be harnessed to generate wind energy for conversion into
electrical power. Due to the variability of wind speed with time and
height, it becomes difficult to predict the generated wind energy more
optimally. In this paper, an attempt is made to establish a
probabilistic model fitting the wind speed data recorded at
Makambako site in Tanzania. Wind speeds and direction were
respectively measured using anemometer (type AN1) and wind Vane
(type WD1) both supplied by Delta-T-Devices at a measurement
height of 2 m. Wind speeds were then extrapolated for the height of
10 m using power law equation with an exponent of 0.47. Data were
analysed using MINITAB statistical software to show the variability
of wind speeds with time and height, and to determine the underlying
probability model of the extrapolated wind speed data. The results
show that wind speeds at Makambako site vary cyclically over time;
and they conform to the Weibull probability distribution. From these
results, Weibull probability density function can be used to predict
the wind energy.
Abstract: In this paper, a bond graph dynamic model for a valvecontrolled
hydraulic cylinder has been developed. A simplified bond
graph model of the inter-actuator interactions in a multi-cylinder
hydraulic system has also been presented. The overall bond graph
model of a valve-controlled hydraulic cylinder was developed by
combining the bond graph sub-models of the pump, spool valve and
the actuator using junction structures. Causality was then assigned
in order to obtain a computational model which could be simulated.
The causal bond graph model of the hydraulic cylinder was verified
by comparing the open loop state responses to those of an ODE
model which had been developed in literature based on the same
assumptions. The results were found to correlate very well both
in the shape of the curves, magnitude and the response times,
thus indicating that the developed model represents the hydraulic
dynamics of a valve-controlled cylinder. A simplified model for interactuator
interaction was presented by connecting an effort source with
constant pump pressure to the zero-junction from which the cylinders
in a multi-cylinder system are supplied with a constant pressure from
the pump. On simulating the state responses of the developed model
under different situations of cylinder operations, indicated that such
a simple model can be used to predict the inter-actuator interactions.
Abstract: In this paper, a new model predictive PID controller
design method for the slip suppression control of EVs (electric
vehicles) is proposed. The proposed method aims to improve the
maneuverability and the stability of EVs by controlling the wheel
slip ratio. The optimal control gains of PID framework are derived
by the model predictive control (MPC) algorithm. There also include
numerical simulation results to demonstrate the effectiveness of the
method.
Abstract: Nowadays, precipitation prediction is required for proper planning and management of water resources. Prediction with neural network models has received increasing interest in various research and application domains. However, it is difficult to determine the best neural network architecture for prediction since it is not immediately obvious how many input or hidden nodes are used in the model. In this paper, neural network model is used as a forecasting tool. The major aim is to evaluate a suitable neural network model for monthly precipitation mapping of Myanmar. Using 3-layerd neural network models, 100 cases are tested by changing the number of input and hidden nodes from 1 to 10 nodes, respectively, and only one outputnode used. The optimum model with the suitable number of nodes is selected in accordance with the minimum forecast error. In measuring network performance using Root Mean Square Error (RMSE), experimental results significantly show that 3 inputs-10 hiddens-1 output architecture model gives the best prediction result for monthly precipitation in Myanmar.