Abstract: Self-sensing estimates the air gap within an electro
magnetic path by analyzing the bearing coil current and/or voltage
waveform. The self-sensing concept presented in this paper has been
developed within the research project “Active Magnetic Bearings
with Supreme Reliability" and is used for position sensor fault
detection.
Within this new concept gap calculation is carried out by an alldigital
analysis of the digitized coil current and voltage waveform.
For analysis those time periods within the PWM period are used,
which give the best results. Additionally, the concept allows the
digital compensation of nonlinearities, for example magnetic
saturation, without degrading signal quality. This increases the
accuracy and robustness of the air gap estimation and additionally
reduces phase delays.
Beneath an overview about the developed concept first
measurement results are presented which show the potential of this
all-digital self-sensing concept.
Abstract: The aim of this study was to determine noise level of
six different types of machines in printing companies in Novi Sad.
The A-weighted levels on Leq, Lmax and Lmin Sound Pressure Level
(SPL) in dBA were measured. It was found that the folders, offset
printing presses and binding machines are the predominant noise
sources. The noise levels produced by 12 of 38 machines exceed the
limiting threshold level of 85 dBA, tolerated by law. Since it was
determined that the average noise level for folders (87.7 dB) exceeds
the permitted value the octave analysis of noise was performed.
Abstract: The interrelationship between international stock
markets has been a key study area among the financial market
researchers for international portfolio management and risk
measurement. The characteristics of security returns and their
dynamics play a vital role in the financial market theory. This study
is an attempt to find out the dynamic linkages among the equity
market of USA and emerging markets of Pakistan and India using
daily data covering the period of January 2003–December 2009. The
study utilizes Johansen (Journal of Economic Dynamics and Control,
12, 1988) and Johansen and Juselius (Oxford Bulletin of Economics
and Statistics, 52, 1990) cointegration procedure for long run
relationship and Granger-causality tests based on Toda and
Yamamoto (Journal of Econometrics, 66, 1995) methodology.
No cointegration was found among stock markets of USA, Pakistan
and India, while Granger-causality test showed the evidence of
unidirectional causality running from New York stock exchange to
Bombay and Karachi stock exchanges.
Abstract: Finding synchronizing sequences for the finite automata is a very important problem in many practical applications (part orienters in industry, reset problem in biocomputing theory, network issues etc). Problem of finding the shortest synchronizing sequence is NP-hard, so polynomial algorithms probably can work only as heuristic ones. In this paper we propose two versions of polynomial algorithms which work better than well-known Eppstein-s Greedy and Cycle algorithms.
Abstract: The objective was to determine the single gene and
interaction effect of composite genotype of beta-kappa casein and
DGAT1 gene on milk yield (MY) and milk composition, content of
milk fat (%FAT), milk protein (%PRO), solid not fat (%SNF), and
total solid (%TS) in crossbred Holstein cows. Two hundred and
thirty- one cows were genotyped with PCR-RFLP for DGAT1 and
composite genotype data of beta-kappa casein from previous work
were used. Two model, (1), and (2), was used to estimate single gene
effect, and interaction effect on the traits, respectively. The
significance of interaction effects on all traits were detected. Most
traits have consistent pattern of significant when model (1), and (2)
were compared, except the effect of composite genotype of betakappa
casein on %FAT, and the effect of DGAT1 on MY, which the
significant difference was detected in only model (1).The results
suggested that when the optimum of all traits was necessary,
interaction effect should be concerned.
Abstract: Tablet computers and Multifunctional Hardcopy Devices (MHDs) are common devices in daily life. Though, many scientific studies have not been published. The tablet computers are straightforward to use whereas the MHDs are comparatively difficult to use. Thus, to assist different levels of users, we propose combining these two devices to achieve straightforward intelligent user interface (UI) and versatile What You See Is What You Get (WYSIWYG) document management and production. Our approach to this issue is to design an intelligent user dependent UI for a MHD applying a tablet computer. Furthermore, we propose hardware interconnection and versatile intelligent software between these two devices. In this study, we first provide a state-of-the-art survey on MHDs and tablet computers, and their interconnections. Secondly we provide a comparative UI survey on two state-of-the-art MHDs with a proposal of a novel UI for the MHDs using Jakob Nielsen-s Ten Usability Heuristics Evaluation.
Abstract: The aim of this paper is to identify the most suitable
model for churn prediction based on three different techniques. The
paper identifies the variables that affect churn in reverence of
customer complaints data and provides a comparative analysis of
neural networks, regression trees and regression in their capabilities
of predicting customer churn.
Abstract: The adoption of building information modeling (BIM)
is increasing in the construction industry. However, quantity
surveyors are slow in adoption compared to other professions due to
lack of awareness of the BIM’s potential in their profession. It is still
unclear on how BIM application can enhance quantity surveyors’
work performance and project performance. The aim of this research
is to identify the capabilities of BIM in quantity surveying practices
and examine the relationship between BIM capabilities and project
performance. Questionnaire survey and interviews were adopted for
data collection. Literature reviews identified there are eleven BIM
capabilities in quantity surveying practice. Questionnaire results
showed that there are several BIM capabilities significantly
correlated with project performance in time, cost and quality aspects
and the results were validated through interviews. These findings
show that BIM has the capabilities to enhance quantity surveyors’
performances and subsequently improved project performance.
Abstract: Knowledge management is a critical component of
competitive success in service organizations. Knowledge
management centers on creating new knowledge and utilizing
existing knowledge. While utilizing existing knowledge relates to
input and control and can lead to a reduction in costs; creating new
knowledge relates to output and growth and can lead to an increase in
revenue. Therefore managers must ensure that they can successfully
optimize the knowledge and talent in their organizations. To do this
they and must try to develop an environment that promotes the
generation, acquisition, transfer and use of valuable knowledge in
creative ways. However knowledge management is complex and
diverse. Research suggests that organizations in general and SMEs in
particular are finding it difficult to implement successful knowledge
management initiatives. Our research attempts to understand whether
organizations are adopting best practice initiatives in their
organizations. This paper presents findings from an exploratory study
of 139 SMEs operating in the tourism sector across Europe. The
goals of the survey is to assess the level of awareness of knowledge
and talent management strategies and methodologies and to
determine whether the responding companies implement best practice
knowledge management initiatives in their organizations Analysis of
the findings from the study are presented and discussed.
Abstract: A multi-block algorithm and its implementation in two-dimensional finite element numerical model CCHE2D are presented. In addition to a conventional Lagrangian Interpolation Method (LIM), a novel interpolation method, called Consistent Interpolation Method (CIM), is proposed for more accurate information transfer across the interfaces. The consistent interpolation solves the governing equations over the auxiliary elements constructed around the interpolation nodes using the same numerical scheme used for the internal computational nodes. With the CIM, the momentum conservation can be maintained as well as the mass conservation. An imbalance correction scheme is used to enforce the conservation laws (mass and momentum) across the interfaces. Comparisons of the LIM and the CIM are made using several flow simulation examples. It is shown that the proposed CIM is physically more accurate and produces satisfactory results efficiently.
Abstract: We report here structural, mechanical and I-V
characteristics of Zn1-xMxO ceramic samples with various x and M.
It is found that the considered dopants does not influence the wellknown
peaks related to wurtzite structure of ZnO ceramics, while the
shape and size of grains are clearly affected. Average crystalline
diameters, deduced from XRD are between 42 nm and 54 nm, which
are 70 times lower than those obtained from SEM micrographs.
Interestingly, the potential barrier could be formed by adding Cu up
to 0.20, and it is completely deformed by 0.025 Ni additions. The
breakdown field could be enhanced up to 4138 V/cm by 0.025 Cu
additions, followed by a decrease with further increase of Cu . On
the other hand a gradual decrease in VHN is reported for both
dopants and their values are higher in Ni samples as compared to Cu
samples. The electrical conductivity is generally improved by Ni,
while addition of Cu improved it only in the over doped region (≥
0.10). These results are discussed in terms of the difference of
valency and ferromagnetic ordering for both dopants as compared to
undoped sample.
Abstract: Composite steel shear wall is a lateral load resisting system which consists of a steel plate with concrete wall attached to one or both sides to prevent it from elastic buckling. The composite behavior is ensured by utilizing high-strength bolts. This paper investigates the effect of distance between bolts, and for this purpose 14 one-story one-bay specimens with various bolts spacing were modeled by finite element code which is developed by the authors. To verify the model, numerical results were compared with a valid experiment which illustrate proper agreement. Results depict increasing the distance between bolts would improve the seismic ever, this increase must be limited, because of large distances will cause widespread buckling of the steel plate in free subpanels between bolts and would result in no improvement. By comparing the results in elastic region, it was observed initial stiffness is not affected by changing the distance.
Abstract: According to historical legend, after the revelation of the holy Qur'an, which gave the hijab compulsory and women were required to cover the head and body with a handkerchief, and the general form of clothing in her veil, Muslim women have begun to comply with this worthy tradition. This article discusses the history of the rise and spread of the hijab and its types. And here is described in detail types of hijab and its intended value, style hijab in different regions. Now wearing the hijab, hijab in general the problem is important not only in the Arab world, but also in the world.
Abstract: The temperature distribution and the heat transfer
rates through a multi-layer door of a furnace were investigated. The
inside of the door was in contact with hot air and the other side of the
door was in contact with room air. Radiation heat transfer from the
walls of the furnace to the door and the door to the surrounding area
was included in the problem. This work is a two dimensional steady
state problem. The Churchill and Chu correlation was used to find
local convection heat transfer coefficients at the surfaces of the
furnace door. The thermophysical properties of air were the functions
of the temperatures. Polynomial curve fitting for the fluid properties
were carried out. Finite difference method was used to discretize for
conduction heat transfer within the furnace door. The Gauss-Seidel
Iteration was employed to compute the temperature distribution in
the door.
The temperature distribution in the horizontal mid plane of the
furnace door in a two dimensional problem agrees with the one
dimensional problem. The local convection heat transfer coefficients
at the inside and outside surfaces of the furnace door are exhibited.
Abstract: A finite element analysis was conducted to determine
the effect of moisture diffusion and hygroscopic swelling in rice. A
parallel simple stochastic modeling was performed to predict the
number of grains cracked as a result of moisture absorption and
hygroscopic swelling. Rice grains were soaked in thermally (25 oC)
controlled water and then tested for compressive stress. The
destructive compressive stress tests revealed through compressive
stress calculation that the peak force required to cause cracking in
grains soaked in water reduced with time as soaking duration was
extended. Results of the experiment showed that several grains had
their value of the predicted compressive stress below the von Mises
stress and were interpreted as grains which become cracked and/or
broke during soaking. The technique developed in this experiment
will facilitate the approximation of the number of grains which will
crack during soaking.
Abstract: Highly pathogenic avian influenza (HPAI) H5N1 viruses have created demand for a cost-effective vaccine to prevent a pandemic of the disease. Here, we report that Trichoplusia ni (T. ni) larvae can act as a cost-effective bioreactor to produce recombinant HA5 (rH5HA) proteins as an potential effective vaccine for chickens. To facilitate the recombinant virus identification, virus titer determination and access the infected larvae, we employed the internal ribosome entry site (IRES) derived from Perina nuda virus (PnV, belongs to insect picorna like Iflavirus genus) to construct a bi-cistronic baculovirus expression vector that can express the rH5HA protein and enhanced green fluorescent protein (EGFP) simultaneously. Western blot analysis revealed that the 70 kDa rH5HA protein and partially cleaved products (40 kDa H5HA1) were generated in T. ni larvae infected with recombinant baculovirus carrying the H5HA gene. These data suggest that the baculovirus-larvae recombinant protein expression system could be a cost-effective platform for H5N1 vaccine production.
Abstract: Due to short product life cycles, increasing variety of
products and short cycles of leap innovations manufacturing
companies have to increase the flexibility of factory structures.
Flexibility of factory structures is based on defined factory planning
processes in which product, process and resource data of various
partial domains have to be considered. Thus factory planning
processes can be characterized as iterative, interdisciplinary and
participative processes [1]. To support interdisciplinary and
participative character of planning processes, a federative factory
data management (FFDM) as a holistic solution will be described.
FFDM is already implemented in form of a prototype. The interim
results of the development of FFDM will be shown in this paper. The
principles are the extracting of product, process and resource data
from documents of various partial domains providing as web services
on a server. The described data can be requested by the factory
planner by using a FFDM-browser.
Abstract: A new decomposition form is introduced in this report
to establish a criterion for the bi-partite separability of Bell diagonal
states. A such criterion takes a quadratic inequality of the coefficients
of a given Bell diagonal states and can be derived via a simple
algorithmic calculation of its invariants. In addition, the criterion can
be extended to a quantum system of higher dimension.
Abstract: Developing a university course schedule is
difficult. This is due to the limitations in the resources
available. The process is made even harder with different
faculties or departments having different ways of stating their
schedule requirements. The person in charge of taking the
schedule requirements and turning them into a proper course
schedule is not only burden with the task of allocating the
appropriate classes and time to lecturers and students, they
also need to understand the schedule requirements. Therefore
a scheduling support system named SATA is developed to
assist ICRESS in the course scheduling process. SATA has
been put to use for several semesters and the results have been
encouraging. It won a bronze medal in the 2008 Invention,
Innovation and Design competition (IID-08) and has been
submitted to be patented in October 2008
Abstract: Training with Functional Electrical Stimulation (FES)
has both physiological and psychological benefits for spinal cord
injured subjects. Commonly used methods for quantification of
spasticity have shown controversial reliability. In this study we
propose a method for quick determination of spasticity in spinal cord
injured subjects on a cycling and measurement system. 23 patients
did training sessions on an instrumented mobile FES cycle three
times a week over two months as part of their clinical rehabilitation
program. Spasticity (MAS) and the legs resistance to the pedaling
motion were assessed before and after the FES training and
measurements were done on the subjects ability to pedal with our
without motor assistance. Measurements with test persons with
incomplete spastic paraplegia have shown that spasticity is decreased
after a 30 min cycling training with functional electrical stimulation
(FES).