Abstract: Fuel cells have become one of the major areas of
research in the academia and the industry. The goal of most fish
farmers is to maximize production and profits while holding labor
and management efforts to the minimum. Risk of fish kills, disease
outbreaks, poor water quality in most pond culture operations,
aeration offers the most immediate and practical solution to water
quality problems encountered at higher stocking and feeding rates.
Many units of aeration system are electrical units so using a
continuous, high reliability, affordable, and environmentally friendly
power sources is necessary. Aeration of water by using PEM fuel cell
power is not only a new application of the renewable energy, but
also, it provides an affordable method to promote biodiversity in
stagnant ponds and lakes. This paper presents a new design and
control of PEM fuel cell powered a diffused air aeration system for a
shrimp farm in Mersa Matruh in Egypt. Also Artificial intelligence
(AI) techniques control is used to control the fuel cell output power
by control input gases flow rate. Moreover the mathematical
modeling and simulation of PEM fuel cell is introduced. A
comparison study is applied between the performance of fuzzy logic
control (FLC) and neural network control (NNC). The results show
the effectiveness of NNC over FLC.
Abstract: In this paper, an alternating implicit block method for
solving two dimensional scalar wave equation is presented. The
new method consist of two stages for each time step implemented
in alternating directions which are very simple in computation. To
increase the speed of computation, a group of adjacent points is
computed simultaneously. It is shown that the presented method
increase the maximum time step size and more accurate than the
conventional finite difference time domain (FDTD) method and other
existing method of natural ordering.
Abstract: This study describes the methodology for the development of a validated in-vitro in-vivo correlation (IVIVC) for metoprolol tartrate modified release dosage forms with distinctive release rate characteristics. Modified release dosage forms were formulated by microencapsulation of metoprolol tartrate into different amounts of ethylcellulose by non-solvent addition technique. Then in-vitro and in-vivo studies were conducted to develop and validate level A IVIVC for metoprolol tartrate. The values of regression co-efficient (R2-values) for IVIVC of T2 and T3 formulations were not significantly (p
Abstract: CO2 is the primary anthropogenic greenhouse gas,
accounting for 77% of the human contribution to the greenhouse
effect in 2004. In the recent years, global concentration of CO2 in the
atmosphere is increasing rapidly. CO2 emissions have an impact on
global climate change. Anthropogenic CO2 is emitted primarily from
fossil fuel combustion. Carbon capture and storage (CCS) is one
option for reducing CO2 emissions. There are three major approaches
for CCS: post-combustion capture, pre-combustion capture and
oxyfuel process. Post-combustion capture offers some advantages as
existing combustion technologies can still be used without radical
changes on them.
There are several post combustion gas separation and capture
technologies being investigated, namely; (a) absorption, (b)
cryogenic separation, (c) membrane separation (d) micro algal biofixation
and (e) adsorption. Apart from establishing new techniques,
the exploration of capture materials with high separation performance
and low capital cost are paramount importance. However, the
application of adsorption from either technology, require easily
regenerable and durable adsorbents with a high CO2 adsorption
capacity. It has recently been reported that the cost of the CO2
capture can be reduced by using this technology. In this paper, the
research progress (from experimental results) in adsorbents for CO2
adsorption, storage, and separations were reviewed and future
research directions were suggested as well.
Abstract: A measurement system was successfully fabricated to
detect ion concentrations (hydrogen and chlorine) in this study.
PIC18F4520, the microcontroller was used as the control unit in the
measurement system. The measurement system was practically used
to sense the H+ and Cl- in different examples, and the pH and pCl
values were exhibited on real-time LCD display promptly. In the study,
the measurement method is used to judge whether the response voltage
is stable. The change quantity is smaller than 0.01%, that the present
response voltage compares with next response voltage for H+
measurement, and the above condition is established only 6 sec.
Besides, the change quantity is smaller than 0.01%, that the present
response voltage compares with next response voltage for Clmeasurement,
and the above condition is established only 5 sec.
Furthermore, the average error quantities would also be considered,
and they are 0.05 and 0.07 for measurements of pH and pCl values,
respectively.
Abstract: Duplicated region detection is a technical method to
expose copy-paste forgeries on digital images. Copy-paste is one
of the common types of forgeries to clone portion of an image
in order to conceal or duplicate special object. In this type of
forgery detection, extracting robust block feature and also high
time complexity of matching step are two main open problems.
This paper concentrates on computational time and proposes a local
block matching algorithm based on block clustering to enhance time
complexity. Time complexity of the proposed algorithm is formulated
and effects of two parameter, block size and number of cluster, on
efficiency of this algorithm are considered. The experimental results
and mathematical analysis demonstrate this algorithm is more costeffective
than lexicographically algorithms in time complexity issue
when the image is complex.
Abstract: Software engineering education not only embraces
technical skills of software development but also necessitates
communication and interaction among learners. In this paper, it is
proposed to adapt the PBL methodology that is especially designed to
be integrated into software engineering classroom in order to promote
collaborative learning environment. This approach helps students
better understand the significance of social aspects and provides a
systematic framework to enhance teamwork skills. The adaptation of
PBL facilitates the transition to an innovative software development
environment where cooperative learning can be actualized.
Abstract: This paper reports the feasibility of the ARMA model
to describe a bursty video source transmitting over a AAL5 ATM link
(VBR traffic). The traffic represents the activity of the action movie
"Lethal Weapon 3" transmitted over the ATM network using the Fore
System AVA-200 ATM video codec with a peak rate of 100 Mbps
and a frame rate of 25. The model parameters were estimated for a
single video source and independently multiplexed video sources. It
was found that the model ARMA (2, 4) is well-suited for the real data
in terms of average rate traffic profile, probability density function,
autocorrelation function, burstiness measure, and the pole-zero
distribution of the filter model.
Abstract: This paper presents the combination of different precipitation data sets and the distributed hydrological model, in order to examine the flood runoff reproductivity of scattered observation catchments. The precipitation data sets were obtained from observation using rain-gages, satellite based estimate (TRMM), and numerical weather prediction model (NWP), then were coupled with the super tank model. The case study was conducted in three basins (small, medium, and large size) located in Central Vietnam. Calculated hydrographs based on ground observation rainfall showed best fit to measured stream flow, while those obtained from TRMM and NWP showed high uncertainty of peak discharges. However, calculated hydrographs using the adjusted rainfield depicted a promising alternative for the application of TRMM and NWP in flood modeling for scattered observation catchments, especially for the extension of forecast lead time.
Abstract: A mathematical model for determining the overall efficiency
of a multistage tractor gearbox including all gear, lubricant,
surface finish related parameters and operating conditions is
presented. Sliding friction, rolling friction and windage losses were
considered as the main sources of power loss in the gearing system. A
computer code in FORTRAN was developed to simulate the model.
Sliding friction contributes about 98% of the total power loss for
gear trains operating at relatively low speeds (less than 2000 rpm
input speed). Rolling frictional losses decrease with increased load
while windage losses are only significant for gears running at very
high speeds (greater than 3000 rpm). The results also showed that the
overall efficiency varies over the path of contact of the gear meshes
ranging between 94% to 99.5%.
Abstract: Suspended cable structures are most preferable for large spans covering due to rational use of structural materials, but the problem of suspended cable structures is initial shape change under the action of non-symmetrical load. The problem can be solved by increasing of relation of dead weight and imposed load, but this methods cause increasing of materials consumption.Prestressed cable truss usage is another way how the problem of shape change under the action of non-symmetrical load can be fixed. The better results can be achieved if we replace top chord with cable truss with cross web. Rational structure of the cable truss for prestressed cable truss top chord was developed using optimization realized in FEM program ANSYS 12 environment. Single cable and cable truss model work was discovered.Analytical and model testing results indicate, that usage of cable truss with the cross web as a top chord of prestressed cable truss instead of single cable allows to reduce total displacements by 13-16% in the case of non-symmetrical load. In case of uniformly distributed load single cable is preferable.
Abstract: A square matrix over the complex field with non- negative integral trace is called a quasi-permutation matrix. For a finite group G the minimal degree of a faithful representation of G by quasi-permutation matrices over the rationals and the complex numbers are denoted by q(G) and c(G) respectively. Finally r (G) denotes the minimal degree of a faithful rational valued complex character of C. The purpose of this paper is to calculate q(G), c(G) and r(G) for the group S L(2, q) when extended by a certain group of order two.
Abstract: This study was to search for the desirable direction of
the sidewalk planning in Korea by establishing the concepts of
walking and pedestrian space, and analyzing the advanced precedents
in and out of country. Also, based on the precedent studies and
relevant laws, regulations, and systems, it aimed for the following
sequential process: firstly, to derive design elements from the
functions and characteristics of sidewalk and cluster the similar
elements by each characteristics, sampling representative
characteristics and making them hierarchical; then, to analyze their
significances via the first questionnaire survey, and the relative
weights and priorities of each elements via the Analytic Hierarchy
Process(AHP); finally, based on the analysis result, to establish the
frame of suggesting the direction of policy to improve the pedestrian
environment of sidewalk in urban commercial district for the future
planning and design of pedestrian space.
Abstract: detecting the deadlock is one of the important
problems in distributed systems and different solutions have been
proposed for it. Among the many deadlock detection algorithms,
Edge-chasing has been the most widely used. In Edge-chasing
algorithm, a special message called probe is made and sent along
dependency edges. When the initiator of a probe receives the probe
back the existence of a deadlock is revealed. But these algorithms are
not problem-free. One of the problems associated with them is that
they cannot detect some deadlocks and they even identify false
deadlocks. A key point not mentioned in the literature is that when
the process is waiting to obtain the required resources and its
execution has been blocked, how it can actually respond to probe
messages in the system. Also the question of 'which process should
be victimized in order to achieve a better performance when multiple
cycles exist within one single process in the system' has received
little attention. In this paper, one of the basic concepts of the
operating system - daemon - will be used to solve the problems
mentioned. The proposed Algorithm becomes engaged in sending
probe messages to the mandatory daemons and collects enough
information to effectively identify and resolve multi-cycle deadlocks
in distributed systems.
Abstract: In realizing devices using ZnO, a key challenge is the
production of p-type material. Substitution of oxygen by a group-V
impurity is thought to result in deep acceptor levels, but a candidate
made up from a complex of a group-V impurity (P, As, Sb) on a Zn
site coupled with two vacant Zn sites is widely viewed as a candidate.
We show using density-functional simulations that in contrast to such
a view, complexes involving oxygen interstitials are energetically
more favorable, resulting in group-V impurities coordinated with four,
five or six oxygen atoms.
Abstract: New graph similarity methods have been proposed in this work with the aim to refining the chemical information extracted from molecules matching. For this purpose, data fusion of the isomorphic and nonisomorphic subgraphs into a new similarity measure, the Approximate Similarity, was carried out by several approaches. The application of the proposed method to the development of quantitative structure-activity relationships (QSAR) has provided reliable tools for predicting several pharmacological parameters: binding of steroids to the globulin-corticosteroid receptor, the activity of benzodiazepine receptor compounds, and the blood brain barrier permeability. Acceptable results were obtained for the models presented here.
Abstract: The aspiration of this research article is to target and
focus the gains of university-Industry (U-I) collaborations and
exploring those hurdles which are the obstacles for attaining these
gains. University-Industry collaborations have attained great
importance since 1980 in USA due to its application in all fields of
life. U-I collaboration is a bilateral process where academia is a
proactive member to make such alliances. Universities want to
ameliorate their academic-base with the technicalities of technobabbles.
U-I collaboration is becoming an essential lane for achieving
innovative goals in this century. Many developed nations have set
successful examples to prove this phenomenon as a catalyst to reduce
costs, efforts and personnel for R&D projects. This study is exploits
amplitudes of UI collaboration incentives in the light of success
stories of developed countries. Many universities in USA, UK,
Canada and various European Countries have been engaged with
enterprises for numerous collaborative agreements. A long list of
strategic and short term R&D projects has been executed in
developed countries to accomplish their intended purposes. Due to
the lack of intentions, genuine research and research-oriented
environment, the mentioned field could not grow very well in
developing countries. During last decade, a new wave of research
has induced the institutes of developing countries to promote R&D
culture especially in Pakistan. Higher Education Commission (HEC)
has initiated many projects and funding supports for universities
which have collaborative intentions with industry.
Findings show that rapid innovation, overwhelm the technological
complexities and articulated intellectual-base are major incentives
which steer both partners to establish faculty-industry alliances. Everchanging
technologies, concerned about intellectual property,
different research environment and culture, research relevancy (Basic
or applied), exposure differences and diversity of knowledge
(bookish or practical) are main barriers to establish and retain joint
ventures. Findings also concluded that, it is dire need to support and
enhance cooperation among academia and industry to promote highly
coordinated research behaviors. Author has proposed a roadmap for
developing countries to promote R&D clusters among faculty and
industry to deal the technological challenges and innovation
complexities. Based on our research findings, Model for R&D
Collaboration for developing countries also have been proposed to
promote articulated R&D environment. If developing countries
follow this phenomenon, rapid innovations can be achieved with
limited R&D budget heads.
Abstract: A novel robust audio watermarking scheme is
proposed in this paper. In the proposed scheme, the host audio signals
are segmented into frames. Two consecutive frames are assessed if
they are suitable to represent a watermark bit. If so, frequency
transform is performed on these two frames. The compressionexpansion
technique is adopted to generate distortion over the two
frames. The distortion is used to represent one watermark bit.
Psychoacoustic model is applied to calculate local auditory mask to
ensure that the distortion is not audible. The watermarking schemes
using mono and stereo audio signals are designed differently. The
correlation-based detection method is used to detect the distortion
and extract embedded watermark bits. The experimental results show
that the quality degradation caused by the embedded watermarks is
perceptually transparent and the proposed schemes are very robust
against different types of attacks.
Abstract: This paper presents the design of a low power second-order continuous-time sigma-delta modulator for low power
applications. The loop filter of this modulator has been implemented based on the nonlinear transconductance-capacitor (Gm-C) by employing current-mode technique. The nonlinear transconductance uses floating gate MOS (FG-MOS) transistors that operate in weak inversion region. The proposed modulator features low power consumption (
Abstract: In this paper an algorithm based on the adaptive
neuro-fuzzy controller is provided to enhance the tipover stability of
mobile manipulators when they are subjected to predefined
trajectories for the end-effector and the vehicle. The controller
creates proper configurations for the manipulator to prevent the robot
from being overturned. The optimal configuration and thus the most
favorable control are obtained through soft computing approaches
including a combination of genetic algorithm, neural networks, and
fuzzy logic. The proposed algorithm, in this paper, is that a look-up
table is designed by employing the obtained values from the genetic
algorithm in order to minimize the performance index and by using
this data base, rule bases are designed for the ANFIS controller and
will be exerted on the actuators to enhance the tipover stability of the
mobile manipulator. A numerical example is presented to
demonstrate the effectiveness of the proposed algorithm.