Abstract: This paper presents a means for reducing the torque
variation during the revolution of a vertical-axis water turbine
(VAWaterT) by increasing the blade number. For this purpose, twodimensional
CFD analyses have been performed on a straight-bladed
Darrieus-type rotor. After describing the computational model and
the relative validation procedure, a complete campaign of
simulations, based on full RANS unsteady calculations, is proposed
for a three, four and five-bladed rotor architectures, characterized by
a NACA 0025 airfoil. For each proposed rotor configuration, flow
field characteristics are investigated at several values of tip speed
ratio, allowing a quantification of the influence of blade number on
flow geometric features and dynamic quantities, such as rotor torque
and power. Finally, torque and power curves are compared for the
three analyzed architectures, achieving a quantification of the effect
of blade number on overall rotor performance.
Abstract: This paper demonstrates the application of craziness based particle swarm optimization (CRPSO) technique for designing the 8th order low pass Infinite Impulse Response (IIR) filter. CRPSO, the much improved version of PSO, is a population based global heuristic search algorithm which finds near optimal solution in terms of a set of filter coefficients. Effectiveness of this algorithm is justified with a comparative study of some well established algorithms, namely, real coded genetic algorithm (RGA) and particle swarm optimization (PSO). Simulation results affirm that the proposed algorithm CRPSO, outperforms over its counterparts not only in terms of quality output i.e. sharpness at cut-off, pass band ripple, stop band ripple, and stop band attenuation but also in convergence speed with assured stability.
Abstract: The precision of heat flux simulation influences the
temperature field and test aberration for TB test and also reflects the
test level for spacecraft development. This paper describes TB tests for
a small satellite using solar simulator, electric heaters, calrod heaters
to evaluate the difference of the three methods. Under the same
boundary condition, calrod heaters cases were about 6oC higher than
solar simulator cases and electric heaters cases for
non-external-heat-flux cases (extreme low temperature cases). While
calrod heaters cases and electric heaters cases were 5~7oC and 2~3oC
lower than solar simulator cases respectively for high temperature
cases. The results show that the solar simulator is better than calrod
heaters for its better collimation, non-homogeneity and stability.
Abstract: The POD-assisted projective integration method based on the equation-free framework is presented in this paper. The method is essentially based on the slow manifold governing of given system. We have applied two variants which are the “on-line" and “off-line" methods for solving the one-dimensional viscous Bergers- equation. For the on-line method, we have computed the slow manifold by extracting the POD modes and used them on-the-fly along the projective integration process without assuming knowledge of the underlying slow manifold. In contrast, the underlying slow manifold must be computed prior to the projective integration process for the off-line method. The projective step is performed by the forward Euler method. Numerical experiments show that for the case of nonperiodic system, the on-line method is more efficient than the off-line method. Besides, the online approach is more realistic when apply the POD-assisted projective integration method to solve any systems. The critical value of the projective time step which directly limits the efficiency of both methods is also shown.
Abstract: Following the loss of NASA's Space Shuttle
Columbia in 2003, it was determined that problems in the agency's
organization created an environment that led to the accident. One
component of the proposed solution resulted in the formation of the
NASA Engineering Network (NEN), a suite of information retrieval
and knowledge-sharing tools. This paper describes the
implementation of communities of practice, which are formed along
engineering disciplines. Communities of practice enable engineers to
leverage their knowledge and best practices to collaborate and take
information learning back to their jobs and embed it into the
procedures of the agency. This case study offers insight into using
traditional engineering disciplines for virtual collaboration, including
lessons learned during the creation and establishment of NASA-s
communities.
Abstract: Current image-based individual human recognition
methods, such as fingerprints, face, or iris biometric modalities
generally require a cooperative subject, views from certain aspects,
and physical contact or close proximity. These methods cannot
reliably recognize non-cooperating individuals at a distance in the
real world under changing environmental conditions. Gait, which
concerns recognizing individuals by the way they walk, is a relatively
new biometric without these disadvantages. The inherent gait
characteristic of an individual makes it irreplaceable and useful in
visual surveillance.
In this paper, an efficient gait recognition system for human
identification by extracting two features namely width vector of
the binary silhouette and the MPEG-7-based region-based shape
descriptors is proposed. In the proposed method, foreground objects
i.e., human and other moving objects are extracted by estimating
background information by a Gaussian Mixture Model (GMM) and
subsequently, median filtering operation is performed for removing
noises in the background subtracted image. A moving target classification
algorithm is used to separate human being (i.e., pedestrian)
from other foreground objects (viz., vehicles). Shape and boundary
information is used in the moving target classification algorithm.
Subsequently, width vector of the outer contour of binary silhouette
and the MPEG-7 Angular Radial Transform coefficients are taken as
the feature vector. Next, the Principal Component Analysis (PCA)
is applied to the selected feature vector to reduce its dimensionality.
These extracted feature vectors are used to train an Hidden Markov
Model (HMM) for identification of some individuals. The proposed
system is evaluated using some gait sequences and the experimental
results show the efficacy of the proposed algorithm.
Abstract: In this paper, Tobephobia (TBP) alludes to the fear of
failure experienced by teachers to manage curriculum change. TBP is
an emerging concept and it extends the boundaries of research in
terms of how we view achievement and failure in education.
Outcomes-based education (OBE) was introduced fifteen years ago
in South African schools without simultaneously upgrading teachers-
professional competencies. This exploratory research, therefore
examines a simple question: What is the impact of TBP and OBE on
teachers? Teacher ineptitude to cope with the OBE curriculum in the
classroom is a serious problem affecting large numbers of South
African teachers. This exploratory study sought to determine the
perceived negative impact of OBE and TBP on teachers. A survey
was conducted amongst 311 teachers in Port Elizabeth and Durban,
South Africa. The results confirm the very negative impact of TBP
and OBE on teachers. This exploratory study authenticates the
existence of TBP.
Abstract: Freeways are originally designed to provide high
mobility to road users. However, the increase in population and
vehicle numbers has led to increasing congestions around the world.
Daily recurrent congestion substantially reduces the freeway capacity
when it is most needed. Building new highways and expanding the
existing ones is an expensive solution and impractical in many
situations. Intelligent and vision-based techniques can, however, be
efficient tools in monitoring highways and increasing the capacity of
the existing infrastructures. The crucial step for highway monitoring
is vehicle detection. In this paper, we propose one of such
techniques. The approach is based on artificial neural networks
(ANN) for vehicles detection and counting. The detection process
uses the freeway video images and starts by automatically extracting
the image background from the successive video frames. Once the
background is identified, subsequent frames are used to detect
moving objects through image subtraction. The result is segmented
using Sobel operator for edge detection. The ANN is, then, used in
the detection and counting phase. Applying this technique to the
busiest freeway in Riyadh (King Fahd Road) achieved higher than
98% detection accuracy despite the light intensity changes, the
occlusion situations, and shadows.
Abstract: Experimental data are presented to show the influence of different types of chemical demulsifier on the stability and demulsification of emulsions. Three groups of demulsifier with different functional groups were used in this work namely amines, alcohol and polyhydric alcohol. The results obtained in this study have exposed the capability of chemical breaking agents in destabilization of water in crude oil emulsions. From the present study, found that molecular weight of the demulsifier were influent the capability of the emulsion to separate.
Abstract: Fructooligosaccharides derived from microbial enzyme especially from fungal sources has been received particular attention due to its beneficial effects as prebiotics and mass production. However, fungal fermentation is always cumbersome due to its broth rheology problem that will eventually affect the production of FOS. This study investigated the efficiency of immobilized cell system using rotating fibrous bed bioreactor (RFBB) in producing fructooligosaccharides (FOS). A comparative picture with respect to conventional stirred tank bioreactor (CSTB) and RFBB has been presented. To demonstrate the effect of agitation intensity and aeration rate, a laboratory-scale bioreactor 2.5 L was operated in three phases (high, medium, low) for 48 hours. Agitation speed has a great influence on P. simplicissimum fermentation for FOS production, where the volumetric FOS productivity using RFBB is increased with almost 4 fold compared to the FOS productivity in CSTB that only 0.319 g/L/h. Rate of FOS production increased up to 1.2 fold when immobilized cells system was employed at aeration rate similar to the freely suspended cells at 2.0 vvm.
Abstract: The common bean is the most important grain legume for direct human consumption in the world and BCMV is one of the world's most serious bean diseases that can reduce yield and quality of harvested product. To determine the best tolerance index to BCMV and recognize tolerant genotypes, 2 experiments were conducted in field conditions. Twenty five common bean genotypes were sown in 2 separate RCB design with 3 replications under contamination and non-contamination conditions. On the basis of the results of indices correlations GMP, MP and HARM were determined as the most suitable tolerance indices. The results of principle components analysis indicated 2 first components totally explained 98.52% of variations among data. The first and second components were named potential yield and stress susceptible respectively. Based on the results of BCMV tolerance indices assessment and biplot analysis WA8563-4, WA8563-2 and Cardinal were the genotypes that exhibited potential seed yield under contamination and noncontamination conditions.
Abstract: The number of framework conceived for e-learning
constantly increase, unfortunately the creators of learning materials
and educational institutions engaged in e-formation adopt a
“proprietor" approach, where the developed products (courses,
activities, exercises, etc.) can be exploited only in the framework
where they were conceived, their uses in the other learning
environments requires a greedy adaptation in terms of time and
effort. Each one proposes courses whose organization, contents,
modes of interaction and presentations are unique for all learners,
unfortunately the latter are heterogeneous and are not interested by
the same information, but only by services or documents adapted to
their needs. Currently the new tendency for the framework
conceived for e-learning, is the interoperability of learning materials,
several standards exist (DCMI (Dublin Core Metadata Initiative)[2],
LOM (Learning Objects Meta data)[1], SCORM (Shareable Content
Object Reference Model)[6][7][8], ARIADNE (Alliance of Remote
Instructional Authoring and Distribution Networks for Europe)[9],
CANCORE (Canadian Core Learning Resource Metadata
Application Profiles)[3]), they converge all to the idea of learning
objects. They are also interested in the adaptation of the learning
materials according to the learners- profile. This article proposes an
approach for the composition of courses adapted to the various
profiles (knowledge, preferences, objectives) of learners, based on
two ontologies (domain to teach and educational) and the learning
objects.
Abstract: The topic of surface flattening plays a vital role in the field of computer aided design and manufacture. Surface flattening enables the production of 2D patterns and it can be used in design and manufacturing for developing a 3D surface to a 2D platform, especially in fashion design. This study describes surface flattening based on minimum energy methods according to the property of different fabrics. Firstly, through the geometric feature of a 3D surface, the less transformed area can be flattened on a 2D platform by geodesic. Then, strain energy that has accumulated in mesh can be stably released by an approximate implicit method and revised error function. In some cases, cutting mesh to further release the energy is a common way to fix the situation and enhance the accuracy of the surface flattening, and this makes the obtained 2D pattern naturally generate significant cracks. When this methodology is applied to a 3D mannequin constructed with feature lines, it enhances the level of computer-aided fashion design. Besides, when different fabrics are applied to fashion design, it is necessary to revise the shape of a 2D pattern according to the properties of the fabric. With this model, the outline of 2D patterns can be revised by distributing the strain energy with different results according to different fabric properties. Finally, this research uses some common design cases to illustrate and verify the feasibility of this methodology.
Abstract: It-s known that incorporating prior knowledge into support
vector regression (SVR) can help to improve the approximation
performance. Most of researches are concerned with the incorporation
of knowledge in the form of numerical relationships. Little work,
however, has been done to incorporate the prior knowledge on the
structural relationships among the variables (referred as to Structural
Prior Knowledge, SPK). This paper explores the incorporation of SPK
in SVR by constructing appropriate admissible support vector kernel
(SV kernel) based on the properties of reproducing kernel (R.K).
Three-levels specifications of SPK are studied with the corresponding
sub-levels of prior knowledge that can be considered for the method.
These include Hierarchical SPK (HSPK), Interactional SPK (ISPK)
consisting of independence, global and local interaction, Functional
SPK (FSPK) composed of exterior-FSPK and interior-FSPK. A
convenient tool for describing the SPK, namely Description Matrix
of SPK is introduced. Subsequently, a new SVR, namely Motivated
Support Vector Regression (MSVR) whose structure is motivated
in part by SPK, is proposed. Synthetic examples show that it is
possible to incorporate a wide variety of SPK and helpful to improve
the approximation performance in complex cases. The benefits of
MSVR are finally shown on a real-life military application, Air-toground
battle simulation, which shows great potential for MSVR to
the complex military applications.
Abstract: A new chelating resin is prepared by coupling Amberlite XAD-4 with 1-amino-2-naphthole through an azo spacer. The resulting sorbent has been characterized by FT-IR, elemental analysis and thermogravimetric analysis (TGA) and studied for preconcentrating of Fe (II) using flame atomic absorption spectrometry (FAAS) for metal monitoring. The optimum pH value for sorption of the iron ions was 6.5. The resin was subjected to evaluation through batch binding of mentioned metal ion. Quantitative desorption occurs instantaneously with 0.5 M HNO3. The sorption capacity was found 4.1 mmol.g-1 of resin for Fe (II) in the aqueous solution. The chelating resin can be reused for 10 cycles of sorption-desorption without any significant change in sorption capacity. A recovery of 97% was obtained the metal ions with 0.5 M HNO3 as eluting agent. The method was applied for metal ions determination from industrial waste water sample.
Abstract: This paper suggests an improved integer frequency
offset (IFO) estimation scheme using P1 symbol for orthogonal
frequency division multiplexing (OFDM) based the second generation
terrestrial digital video broadcasting (DVB-T2) system. Proposed
IFO estimator is designed by a low-complexity blind IFO estimation
scheme, which is implemented with complex additions. Also, we
propose active carriers (ACs) selection scheme in order to prevent
performance degradation in blind IFO estimation. The simulation
results show that under the AWGN and TU6 channels, the proposed
method has low complexity than conventional method and almost
similar performance in comparison with the conventional method.
Abstract: Many recent high energy physics calculations
involving charm and beauty invoke wave function at the origin
(WFO) for the meson bound state. Uncertainties of charm and beauty
quark masses and different models for potentials governing these
bound states require a simple numerical algorithm for evaluation of
the WFO's for these bound states. We present a simple algorithm for
this propose which provides WFO's with high precision compared
with similar ones already obtained in the literature.
Abstract: A complete spectral representation for the
electromagnetic field of planar multilayered waveguides
inhomogeneously filled with omega media is presented. The problem
of guided electromagnetic propagation is reduced to an eigenvalue
equation related to a 2 ´ 2 matrix differential operator. Using the
concept of adjoint waveguide, general bi-orthogonality relations for
the hybrid modes (either from the discrete or from the continuous
spectrum) are derived. For the special case of homogeneous layers
the linear operator formalism is reduced to a simple 2 ´ 2 coupling
matrix eigenvalue problem. Finally, as an example of application, the
surface and the radiation modes of a grounded omega slab waveguide
are analyzed.
Abstract: PPX(Pretty Printer for XML) is a query language that offers a concise description method of formatting the XML data into HTML. In this paper, we propose a simple specification of formatting method that is a combination description of automatic layout operators and variables in the layout expression of the GENERATE clause of PPX. This method can automatically format irregular XML data included in a part of XML with layout decision rule that is referred to DTD. In the experiment, a quick comparison shows that PPX requires far less description compared to XSLT or XQuery programs doing same tasks.
Abstract: Many footbridges have natural frequencies that
coincide with the dominant frequencies of the pedestrian-induced
load and therefore they have a potential to suffer excessive vibrations
under dynamic loads induced by pedestrians. Some of the design
standards introduce load models for pedestrian loads applicable for
simple structures. Load modeling for more complex structures, on the
other hand, is most often left to the designer. The main focus of this
paper is on the human induced forces transmitted to a footbridge and
on the ways these loads can be modeled to be used in the dynamic
design of footbridges. Also design criteria and load models proposed
by widely used standards were introduced and a comparison was
made. The dynamic analysis of the suspension bridge in Kolin in the
Czech Republic was performed on detailed FEM model using the
ANSYS program system. An attempt to model the load imposed by a
single person and a crowd of pedestrians resulted in displacements
and accelerations that are compared with serviceability criteria.