Abstract: An array of piezoelectric micro actuators can be used
for radiation of an ultrasonic carrier signal modulated in amplitude
with an acoustic signal, which yields audio frequency applications as
the air acts as a self-demodulating medium. This application is
known as the parametric array. We propose a parametric array with
array elements based on existing piezoelectric micro ultrasonic
transducer (pMUT) design techniques. In order to reach enough
acoustic output power at a desired operating frequency, a proper ratio
between number of array elements and array size needs to be used,
with an array total area of the order of one cm square. The
transducers presented are characterized via impedance, admittance,
noise figure, transducer gain and frequency responses.
Abstract: Cutting fluids, usually in the form of a liquid, are
applied to the chip formation zone in order to improve the cutting
conditions. Cutting fluid can be expensive and represents a biological
and environmental hazard that requires proper recycling and
disposal, thus adding to the cost of the machining operation. For
these reasons dry cutting or dry machining has become an
increasingly important approach; in dry machining no coolant or
lubricant is used. This paper discussed the effect of the dry cutting on
cutting force and tool life when machining aerospace materials
(Haynes 242) with using two different coated carbide cutting tools
(TiAlN and TiN/MT-TiCN/TiN). Response surface method (RSM)
was used to minimize the number of experiments. ParTiAlN Swarm
Optimisation (PSO) models were developed to optimize the
machining parameters (cutting speed, federate and axial depth) and
obtain the optimum cutting force and tool life. It observed that
carbide cutting tool coated with TiAlN performed better in dry
cutting compared with TiN/MT-TiCN/TiN. On other hand, TiAlN
performed more superior with using of 100 % water soluble coolant.
Due to the high temperature produced by aerospace materials, the
cutting tool still required lubricant to sustain the heat transfer from
the workpiece.
Abstract: Movable power sources of proton exchange
membrane fuel cells (PEMFC) are the important research done in the
current fuel cells (FC) field. The PEMFC system control influences
the cell performance greatly and it is a control system for industrial
complex problems, due to the imprecision, uncertainty and partial
truth and intrinsic nonlinear characteristics of PEMFCs. In this paper
an adaptive PI control strategy using neural network adaptive Morlet
wavelet for control is proposed. It is based on a single layer feed
forward neural networks with hidden nodes of adaptive morlet
wavelet functions controller and an infinite impulse response (IIR)
recurrent structure. The IIR is combined by cascading to the network
to provide double local structure resulting in improving speed of
learning. The proposed method is applied to a typical 1 KW PEMFC
system and the results show the proposed method has more accuracy
against to MLP (Multi Layer Perceptron) method.
Abstract: One of the most basic functions of control engineers is
tuning of controllers. There are always several process loops in the
plant necessitate of tuning. The auto tuned Proportional Integral
Derivative (PID) Controllers are designed for applications where
large load changes are expected or the need for extreme accuracy and
fast response time exists. The algorithm presented in this paper is
used for the tuning PID controller to obtain its parameters with a
minimum computing complexity. It requires continuous analysis of
variation in few parameters, and let the program to do the plant test
and calculate the controller parameters to adjust and optimize the
variables for the best performance. The algorithm developed needs
less time as compared to a normal step response test for continuous
tuning of the PID through gain scheduling.
Abstract: LabVIEW and SIMULINK are two most widely used
graphical programming environments for designing digital signal
processing and control systems. Unlike conventional text-based
programming languages such as C, Cµ and MATLAB, graphical
programming involves block-based code developments, allowing a
more efficient mechanism to build and analyze control systems. In
this paper a LabVIEW environment has been employed as a
graphical user interface for monitoring the operation of a controlled
distillation column, by visualizing both the closed loop performance
and the user selected control conditions, while the column dynamics
has been modeled under the SIMULINK environment. This tool has
been applied to the PID based decoupled control of a binary
distillation column. By means of such integrated environments the
control designer is able to monitor and control the plant behavior and
optimize the response when both, the quality improvement of
distillation products and the operation efficiency tasks, are
considered.
Abstract: This paper attempts to explain response components of Electrovestibulography (EVestG) using a computer simulation of a three-canal model of the vestibular system. EVestG is a potentially new diagnostic method for Meniere's disease. EVestG is a variant of Electrocochleography (ECOG), which has been used as a standard method for diagnosing Meniere's disease - it can be used to measure the SP/AP ratio, where an SP/AP ratio greater than 0.4-0.5 is indicative of Meniere-s Disease. In EVestG, an applied head tilt replaces the acoustic stimulus of ECOG. The EVestG output is also an SP/AP type plot, where SP is the summing potential, and AP is the action potential amplitude. AP is thought of as being proportional to the size of a population of afferents in an excitatory neural firing state. A simulation of the fluid volume displacement in the vestibular labyrinth in response to various types of head tilts (ipsilateral, backwards and horizontal rotation) was performed, and a simple neural model based on these simulations developed. The simple neural model shows that the change in firing rate of the utricle is much larger in magnitude than the change in firing rates of all three semi-circular canals following a head tilt (except in a horizontal rotation). The data suggests that the change in utricular firing rate is a minimum 2-3 orders of magnitude larger than changes in firing rates of the canals during ipsilateral/backward tilts. Based on these results, the neural response recorded by the electrode in our EVestG recordings is expected to be dominated by the utricle in ipsilateral/backward tilts (It is important to note that the effect of the saccule and efferent signals were not taken into account in this model). If the utricle response dominates the EVestG recordings as the modeling results suggest, then EVestG has the potential to diagnose utricular hair cell damage due to a viral infection (which has been cited as one possible cause of Meniere's Disease).
Abstract: Rutting is one of the major load-related distresses in airport flexible pavements. Rutting in paving materials develop gradually with an increasing number of load applications, usually appearing as longitudinal depressions in the wheel paths and it may be accompanied by small upheavals to the sides. Significant research has been conducted to determine the factors which affect rutting and how they can be controlled. Using the experimental design concepts, a series of tests can be conducted while varying levels of different parameters, which could be the cause for rutting in airport flexible pavements. If proper experimental design is done, the results obtained from these tests can give a better insight into the causes of rutting and the presence of interactions and synergisms among the system variables which have influence on rutting. Although traditionally, laboratory experiments are conducted in a controlled fashion to understand the statistical interaction of variables in such situations, this study is an attempt to identify the critical system variables influencing airport flexible pavement rut depth from a statistical DoE perspective using real field data from a full-scale test facility. The test results do strongly indicate that the response (rut depth) has too much noise in it and it would not allow determination of a good model. From a statistical DoE perspective, two major changes proposed for this experiment are: (1) actual replication of the tests is definitely required, (2) nuisance variables need to be identified and blocked properly. Further investigation is necessary to determine possible sources of noise in the experiment.
Abstract: This paper presents the application of discrete-time
variable structure control with sliding mode based on the 'reaching
law' method for robust control of a 'simple inverted pendulum on
moving cart' - a standard nonlinear benchmark system. The
controllers designed using the above techniques are completely
insensitive to parametric uncertainty and external disturbance. The
controller design is carried out using pole placement technique to find
state feedback gain matrix , which decides the dynamic behavior
of the system during sliding mode. This is followed by feedback gain
realization using the control law which is synthesized from 'Gao-s
reaching law'. The model of a single inverted pendulum and the
discrete variable structure control controller are developed, simulated
in MATLAB-SIMULINK and results are presented. The response of
this simulation is compared with that of the discrete linear quadratic
regulator (DLQR) and the advantages of sliding mode controller over
DLQR are also presented
Abstract: The paper deals with the analysis of the dynamic
response of footbridges under human - induced dynamic loads.
This is a frequently occurring and often dominant load for
footbridges as it stems from the very purpose of a footbridge - to
convey pedestrian. Due to the emergence of new materials and
advanced engineering technology, slender footbridges are
increasingly becoming popular to satisfy the modern transportation
needs and the aesthetical requirements of the society. These
structures however are always lively with low stiffness, low mass,
low damping and low natural frequencies. As a consequence, they are
prone to vibration induced by human activities and can suffer severe
vibration serviceability problems, particularly in the lateral direction.
Pedestrian bridges are designed according to first and second limit
states, these are the criteria involved in response to static design load.
However, it is necessary to assess the dynamic response of bridge
design load on pedestrians and assess it impact on the comfort of the
user movement. Usually the load is considered a person or a small
group which can be assumed in perfect motion synchronization.
Already one person or small group can excite significant vibration of
the deck. In order to calculate the dynamic response to the movement
of people, designer needs available and suitable computational model
and criteria. For the calculation program ANSYS based on finite
element method was used.
Abstract: This paper presents a methodical approach for designing and optimizing process parameters in oil blending industries. Twenty seven replicated experiments were conducted for production of A-Z crown super oil (SAE20W/50) employing L9 orthogonal array to establish process response parameters. Power law model was fitted to experimental data and the obtained model was optimized applying the central composite design (CCD) of response surface methodology (RSM). Quadratic model was found to be significant for production of A-Z crown supper oil. The study recognized and specified four new lubricant formulations that conform to ISO oil standard in the course of analyzing the batch productions of A-Z crown supper oil as: L1: KV = 21.8293Cst, BS200 = 9430.00Litres, Ad102=11024.00Litres, PVI = 2520 Litres, L2: KV = 22.513Cst, BS200 = 12430.00 Litres, Ad102 = 11024.00 Litres, PVI = 2520 Litres, L3: KV = 22.1671Cst, BS200 = 9430.00 Litres, Ad102 = 10481.00 Litres, PVI= 2520 Litres, L4: KV = 22.8605Cst, BS200 = 12430.00 Litres, Ad102 = 10481.00 Litres, PVI = 2520 Litres. The analysis of variance showed that quadratic model is significant for kinematic viscosity production while the R-sq value statistic of 0.99936 showed that the variation of kinematic viscosity is due to its relationship with the control factors. This study therefore resulted to appropriate blending proportions of lubricants base oil and additives and recommends the optimal kinematic viscosity of A-Z crown super oil (SAE20W/50) to be 22.86Cst.
Abstract: Deciding the numerous parameters involved in
designing a competent artificial neural network is a complicated task.
The existence of several options for selecting an appropriate
architecture for neural network adds to this complexity, especially
when different applications of heterogeneous natures are concerned.
Two completely different applications in engineering and medical
science were selected in the present study including prediction of
workpiece's surface roughness in ultrasonic-vibration assisted turning
and papilloma viruses oncogenicity. Several neural network
architectures with different parameters were developed for each
application and the results were compared. It was illustrated in this
paper that some applications such as the first one mentioned above
are apt to be modeled by a single network with sufficient accuracy,
whereas others such as the second application can be best modeled
by different expert networks for different ranges of output.
Development of knowledge about the essentials of neural networks
for different applications is regarded as the cornerstone of
multidisciplinary network design programs to be developed as a
means of reducing inconsistencies and the burden of the user
intervention.
Abstract: Glazing is a process used to reduce undesirable drying or dehydration of fish during frozen or cold storage. To evaluate the effect of the time/ temperature binomial of the cryogenic frozen tunnel in the amount of glazing watera Central Composite Rotatable Design was used, with application of the Response Surface Methodology. The results reveal that the time/ temperature obtained for pink cusk-eel in experimental conditions for glazing water are similar to the industrial process, but for red fish and merluza the industrial process needs some adjustments. Control charts were established and implementedto control the amount of glazing water on sardine and merluza. They show that the freezing process was statistically controlled but there were some tendencies that must be analyzed, since the trend of sample mean values approached either of the limits, mainly in merluza. Thus, appropriate actions must be taken, in order to improve the process.
Abstract: One of the common problems encountered in software
engineering is addressing and responding to the changing nature of
requirements. While several approaches have been devised to address
this issue, ranging from instilling resistance to changing requirements
in order to mitigate impact to project schedules, to developing an
agile mindset towards requirements, the approach discussed in this
paper is one of conceptualizing the delta in requirement and
modeling it, in order to plan a response to it. To provide some
context here, change is first formally identified and categorized as
either formal change or informal change. While agile methodology
facilitates informal change, the approach discussed in this paper
seeks to develop the idea of facilitating formal change. To collect,
document meta-requirements that represent the phenomena of change
would be a pro-active measure towards building a realistic cognition
of the requirements entity that can further be harnessed in the
software engineering process.
Abstract: This paper presents a microstrip meandered open
circuited stub with bandstop characteristic. The proposed structure is
designed on a high frequency laminate with dielectric constant of 4.0
and board thickness of 0.508 millimeters. The scattering parameters
and electromagnetic field distributions at various frequencies are
investigated by modeling the structure with three dimensional
electromagnetic simulation tool. In order to describe the resonant
and bandstop characteristic of the meandered open circuited stub, a
Smith chart as well as electric field at various frequencies and phases
is illustrated accordingly. The structure can be an alternative method
in suppressing the harmonic response of a bandpass filter.
Abstract: The globe Sustainability has become the subject of international attention, the key reason is that global climate change. Climate and disasters around the abnormal frequency multiplier, the global temperature of the catastrophe and disaster continue to occur throughout the world, as well as countries around the world. Currently there are many important international conferences and policy, it is a "global environmental sustainability " and "living human health " as the goal of development, including the APEC 2007 meeting to "climate Clean Energy" as the theme Sydney Declaration, 2008 World Economic Forum's "Carbon - promote Cool Earth energy efficiency improvement project", the EU proposed "Green Idea" program, the Japanese annual policy, "low-carbon society, sustainable eco-city environment (Eco City) "And from 2009 to 2010 to promote the "Eco-Point" to promote green energy and carbon reduction products .And the 2010 World Climate Change Conference (COP16 United Nations Climate Change Conference Copenhagen), the world has been the subject of Negative conservative "Environmental Protection ", "save energy consumption, " into a positive response to the "Sustainable " and" LOHAS", while Taiwan has actively put forward eco-cities, green building, green building materials and other related environmental response Measures, especially green building construction environment that is the basis of factors, the most widely used application level, and direct contact with human health and the key to sustainable planet. "Sustainable development "is a necessary condition for continuation of the Earth, "healthy and comfortable" is a necessary condition for the continuation of life, and improve the "quality" is a necessary condition for economic development, balance between the three is "to enhance the efficiency of ", According to the World Business Council for Sustainable Development (WBCSD) for the "environmental efficiency "(Eco-Efficiency) proposed: " the achievement of environmental efficiency, the price to be competitive in the provision of goods or services to meet people's needs, improve living Quality at the same time, the goods or services throughout the life cycle. Its impact on the environment and natural resource utilization and gradually reduced to the extent the Earth can load. "whichever is the economy "Economic" and " Ecologic". The research into the methodology to obtain the Taiwan Green Building Material Labeling product as the scope of the study, by investigating and weight analysis to explore green building environmental load (Ln) factor and the Green Building Quality (Qn) factor to Establish green building environmental efficiency assessment model (GBM Eco-Efficiency). And building materials for healthy green label products for priority assessment object, the object is set in the material evidence for the direct response to the environmental load from the floor class-based, explicit feedback correction to the Green Building environmental efficiency assessment model, "efficiency " as a starting point to achieve balance between human "health "and Earth "sustainable development of win-win strategy. The study is expected to reach 1.To establish green building materials and the quality of environmental impact assessment system, 2. To establish value of GBM Eco-Efficiency model, 3. To establish the GBM Eco-Efficiency model for application of green building material feedback mechanisms.
Abstract: Reduction of Single Input Single Output (SISO) continuous systems into Reduced Order Model (ROM), using a conventional and an evolutionary technique is presented in this paper. In the conventional technique, the mixed advantages of Mihailov stability criterion and continued fraction expansions (CFE) technique is employed where the reduced denominator polynomial is derived using Mihailov stability criterion and the numerator is obtained by matching the quotients of the Cauer second form of Continued fraction expansions. In the evolutionary technique method Particle Swarm Optimization (PSO) is employed to reduce the higher order model. PSO method is based on the minimization of the Integral Squared Error (ISE) between the transient responses of original higher order model and the reduced order model pertaining to a unit step input. Both the methods are illustrated through numerical example.
Abstract: In this paper, a model of self-organizing spiking neural networks is introduced and applied to mobile robot environment representation and path planning problem. A network of spike-response-model neurons with a recurrent architecture is used to create robot-s internal representation from surrounding environment. The overall activity of network simulates a self-organizing system with unsupervised learning. A modified A* algorithm is used to find the best path using this internal representation between starting and goal points. This method can be used with good performance for both known and unknown environments.
Abstract: Interaction effects of xanthan gum (XG), carboxymethyl
cellulose (CMC), and locust bean gum (LBG) on the flow properties
of oil-in-water emulsions were investigated by a mixture design
experiment. Blends of XG, CMC and LBG were prepared according
to an augmented simplex-centroid mixture design (10 points) and used
at 0.5% (wt/wt) in the emulsion formulations. An appropriate
mathematical model was fitted to express each response as a function
of the proportions of the blend components that are able to
empirically predict the response to any blend of combination of the
components. The synergistic interaction effect of the ternary
XG:CMC:LBG blends at approximately 33-67% XG levels was
shown to be much stronger than that of the binary XG:LBG blend at
50% XG level (p < 0.05). Nevertheless, an antagonistic interaction
effect became significant as CMC level in blends was more than 33%
(p < 0.05). Yield stress and apparent viscosity (at 10 s-1) responses
were successfully fitted with a special quartic model while flow
behaviour index and consistency coefficient were fitted with a full
quartic model (R2
adjusted ≥ 0.90). This study found that a mixture
design approach could serve as a valuable tool in better elucidating
and predicting the interaction effects beyond the conventional twocomponent
blends.
Abstract: This paper describes a practical approach to design
and develop a hybrid learning with acceleration feedback control
(HLC) scheme for input tracking and end-point vibration suppression
of flexible manipulator systems. Initially, a collocated proportionalderivative
(PD) control scheme using hub-angle and hub-velocity
feedback is developed for control of rigid-body motion of the system.
This is then extended to incorporate a further hybrid control scheme
of the collocated PD control and iterative learning control with
acceleration feedback using genetic algorithms (GAs) to optimize the
learning parameters. Experimental results of the response of the
manipulator with the control schemes are presented in the time and
frequency domains. The performance of the HLC is assessed in terms
of input tracking, level of vibration reduction at resonance modes and
robustness with various payloads.
Abstract: The seismic rehabilitation designs of two reinforced
concrete school buildings, representative of a wide stock of similar
edifices designed under earlier editions of the Italian Technical
Standards, are presented in this paper. The mutual retrofit solution
elaborated for the two buildings consists in the incorporation of a
dissipative bracing system including pressurized fluid viscous springdampers
as passive protective devices. The mechanical parameters,
layouts and locations selected for the constituting elements of the
system; the architectural renovation projects developed to properly
incorporate the structural interventions and improve the appearance
of the buildings; highlights of the installation works already
completed in one of the two structures; and a synthesis of the
performance assessment analyses carried out in original and
rehabilitated conditions, are illustrated. The results of the analyses
show a remarkable enhancement of the seismic response capacities of
both structures. This allows reaching the high performance objectives
postulated in the retrofit designs with much lower costs and
architectural intrusion as compared to traditional rehabilitation
interventions designed for the same objectives.