Abstract: The B'enard-Marangoni thermal instability problem for
a viscoelastic Jeffreys- fluid layer with internal heat generation is
investigated. The fluid layer is bounded above by a realistic free
deformable surface and by a plane surface below. Our analysis
shows that while the internal heat generation and the relaxation time
both destabilize the fluid layer, its stability may be enhanced by an
increased retardation time.
Abstract: Presented herein is an assessment of current nonlinear
static procedures (NSPs) for seismic evaluation of bucklingrestrained
braced frames (BRBFs) which have become a favorable
lateral-force resisting system for earthquake resistant buildings. The
bias and accuracy of modal, improved modal pushover analysis
(MPA, IMPA) and mass proportional pushover (MPP) procedures
are comparatively investigated when they are applied to BRBF
buildings subjected to two sets of strong ground motions. The
assessment is based on a comparison of seismic displacement
demands such as target roof displacements, peak floor/roof
displacements and inter-story drifts. The NSP estimates are compared
to 'exact' results from nonlinear response history analysis (NLRHA).
The response statistics presented show that the MPP
procedure tends to significantly overestimate seismic demands of
lower stories of tall buildings considered in this study while MPA
and IMPA procedures provide reasonably accurate results in
estimating maximum inter-story drift over all stories of studied BRBF
systems.
Abstract: In order to accommodate various multimedia
services, next generation wireless networks are characterized
by very high transmission bit rates. Thus, in such systems and
networks, the received signal is not only limited by noise but -
especially with increasing symbols rate often more
significantly by the intersymbol interference (ISI) caused by
the time dispersive radio channels such as those are used in
this work. This paper deals with the study of the performance
of detector for high bit rate transmission on some worst case
models of frequency selective fading channels for outdoor
mobile radio environments. This paper deals with a number of
different wireless channels with different power profiles and
different number of resolvable paths. All the radio channels
generated in this paper are for outdoor vehicular environments
with Doppler spread of 100 Hz. A carrier frequency of 1800
MHz is used and all the channels used in this work are such
that they are useful for next generation wireless systems.
Schemes for mitigation of ISI with adaptive equalizers of
different types have been investigated and their performances
have been investigated in terms of BER measured as a function
of SNR.
Abstract: QoS Routing aims to find paths between senders and
receivers satisfying the QoS requirements of the application which
efficiently using the network resources and underlying routing
algorithm to be able to find low-cost paths that satisfy given QoS
constraints. The problem of finding least-cost routing is known to be
NP-hard or complete and some algorithms have been proposed to
find a near optimal solution. But these heuristics or algorithms either
impose relationships among the link metrics to reduce the complexity
of the problem which may limit the general applicability of the
heuristic, or are too costly in terms of execution time to be applicable
to large networks. In this paper, we concentrate an algorithm that
finds a near-optimal solution fast and we named this algorithm as
optimized Delay Constrained Routing (ODCR), which uses an
adaptive path weight function together with an additional constraint
imposed on the path cost, to restrict search space and hence ODCR
finds near optimal solution in much quicker time.
Abstract: Over the past few years, a number of efforts have
been exerted to build parallel processing systems that utilize the idle
power of LAN-s and PC-s available in many homes and corporations.
The main advantage of these approaches is that they provide cheap
parallel processing environments for those who cannot afford the
expenses of supercomputers and parallel processing hardware.
However, most of the solutions provided are not very flexible in the
use of available resources and very difficult to install and setup.
In this paper, a multi-level web-based parallel processing system
(MWPS) is designed (appendix). MWPS is based on the idea of
volunteer computing, very flexible, easy to setup and easy to use.
MWPS allows three types of subscribers: simple volunteers (single
computers), super volunteers (full networks) and end users. All of
these entities are coordinated transparently through a secure web site.
Volunteer nodes provide the required processing power needed by
the system end users. There is no limit on the number of volunteer
nodes, and accordingly the system can grow indefinitely. Both
volunteer and system users must register and subscribe. Once, they
subscribe, each entity is provided with the appropriate MWPS
components. These components are very easy to install.
Super volunteer nodes are provided with special components that
make it possible to delegate some of the load to their inner nodes.
These inner nodes may also delegate some of the load to some other
lower level inner nodes .... and so on. It is the responsibility of the
parent super nodes to coordinate the delegation process and deliver
the results back to the user.
MWPS uses a simple behavior-based scheduler that takes into
consideration the current load and previous behavior of processing
nodes. Nodes that fulfill their contracts within the expected time get a
high degree of trust. Nodes that fail to satisfy their contract get a
lower degree of trust.
MWPS is based on the .NET framework and provides the minimal
level of security expected in distributed processing environments.
Users and processing nodes are fully authenticated. Communications
and messages between nodes are very secure. The system has been
implemented using C#.
MWPS may be used by any group of people or companies to
establish a parallel processing or grid environment.
Abstract: Skyline extraction in mountainous images can be used
for navigation of vehicles or UAV(unmanned air vehicles), but it is
very hard to extract skyline shape because of clutters like clouds, sea
lines and field borders in images. We developed the edge-based
skyline extraction algorithm using a proposed multistage edge filtering
(MEF) technique. In this method, characteristics of clutters in the
image are first defined and then the lines classified as clutters are
eliminated by stages using the proposed MEF technique. After this
processing, we select the last line using skyline measures among the
remained lines. This proposed algorithm is robust under severe
environments with clutters and has even good performance for
infrared sensor images with a low resolution. We tested this proposed
algorithm for images obtained in the field by an infrared camera and
confirmed that the proposed algorithm produced a better performance
and faster processing time than conventional algorithms.
Abstract: The latest Geographic Information System (GIS)
technology makes it possible to administer the spatial components of
daily “business object," in the corporate database, and apply suitable
geographic analysis efficiently in a desktop-focused application. We
can use wireless internet technology for transfer process in spatial
data from server to client or vice versa. However, the problem in
wireless Internet is system bottlenecks that can make the process of
transferring data not efficient. The reason is large amount of spatial
data. Optimization in the process of transferring and retrieving data,
however, is an essential issue that must be considered. Appropriate
decision to choose between R-tree and Quadtree spatial data indexing
method can optimize the process. With the rapid proliferation of
these databases in the past decade, extensive research has been
conducted on the design of efficient data structures to enable fast
spatial searching. Commercial database vendors like Oracle have also
started implementing these spatial indexing to cater to the large and
diverse GIS. This paper focuses on the decisions to choose R-tree
and quadtree spatial indexing using Oracle spatial database in mobile
GIS application. From our research condition, the result of using
Quadtree and R-tree spatial data indexing method in one single
spatial database can save the time until 42.5%.
Abstract: Multiparty voice over IP (MVoIP) systems allows a group of people to freely communicate each other via the internet, which have many applications such as online gaming, teleconferencing, online stock trading etc. Peertalk is a peer to peer multiparty voice over IP system (MVoIP) which is more feasible than existing approaches such as p2p overlay multicast and coupled distributed processing. Since the stream mixing and distribution are done by the peers, it is vulnerable to major security threats like nodes misbehavior, eavesdropping, Sybil attacks, Denial of Service (DoS), call tampering, Man in the Middle attacks etc. To thwart the security threats, a security framework called PEERTS (PEEred Reputed Trustworthy System for peertalk) is implemented so that efficient and secure communication can be carried out between peers.
Abstract: This paper presents a pulse doubling technique in a 12-pulse ac-dc converter which supplies direct torque controlled motor drives (DTCIMD-s) in order to have better power quality conditions at the point of common coupling. The proposed technique increases the number of rectification pulses without significant changes in the installations and yields in harmonic reduction in both ac and dc sides. The 12-pulse rectified output voltage is accomplished via two paralleled six-pulse ac-dc converters each of them consisting of three-phase diode bridge rectifier. An autotransformer is designed to supply the rectifiers. The design procedure of magnetics is in a way such that makes it suitable for retrofit applications where a six-pulse diode bridge rectifier is being utilized. Independent operation of paralleled diode-bridge rectifiers, i.e. dc-ripple re-injection methodology, requires a Zero Sequence Blocking Transformer (ZSBT). Finally, a tapped interphase reactor is connected at the output of ZSBT to double the pulse numbers of output voltage up to 24 pulses. The aforementioned structure improves power quality criteria at ac mains and makes them consistent with the IEEE-519 standard requirements for varying loads. Furthermore, near unity power factor is obtained for a wide range of DTCIMD operation. A comparison is made between 6- pulse, 12-pulse, and proposed converters from view point of power quality indices. Results show that input current total harmonic distortion (THD) is less than 5% for the proposed topology at various loads.
Abstract: In this paper present a sensorless maximum wind power extraction for variable speed constant frequency (VSCF) wind power generation systems with a doubly-fed induction generators (DFIG), to ensure stability and to impose the ideal feedback control solution despite of model uncertainties , using the principles of an active and reactive power controller (DPC) a robust sliding mode power control has been proposed to guarantees fast response times and precise control actions for control the active and reactive power independently. The simulation results in MATLAB/Simulink platform confirmed the good dynamic performance of power control approach for DFIGbased variable speed wind turbines.
Abstract: The focus of the study is to understand the factors of
curriculum innovation from the perspective of Language teacher
education. The overall aim of the study is to investigate Language
educators- perceptions of factors of curriculum innovation. In the
theoretical framework the main focus is on discussion about different
curriculum approaches for language teacher education and limiting
and facilitating factors of innovation. In order to achieve the aim of
the study, an observational research is employed. The empirical basis
of the study consists of questionnaire with sixty-three language
teachers from eight Romanian higher education institutions. The
findings reveal variation in Language teachers- conceptions of the
dominant factors of curricular innovation.
Abstract: The brain MR imaging-based clinical research and analysis system were specifically built and the development for a large-scale data was targeted. We used the general clinical data available for building large-scale data. Registration period for the selection of the lesion ROI and the region growing algorithm was used and the Mesh-warp algorithm for matching was implemented. The accuracy of the matching errors was modified individually. Also, the large ROI research data can accumulate by our developed compression method. In this way, the correctly decision criteria to the research result was suggested. The experimental groups were age, sex, MR type, patient ID and smoking which can easily be queries. The result data was visualized of the overlapped images by a color table. Its data was calculated by the statistical package. The evaluation for the utilization of this system in the chronic ischemic damage in the area has done from patients with the acute cerebral infarction. This is the cause of neurologic disability index location in the center portion of the lateral ventricle facing. The corona radiate was found in the position. Finally, the system reliability was measured both inter-user and intra-user registering correlation.
Abstract: The evolutionary design of electronic circuits, or
evolvable hardware, is a discipline that allows the user to
automatically obtain the desired circuit design. The circuit
configuration is under the control of evolutionary algorithms. Several
researchers have used evolvable hardware to design electrical
circuits. Every time that one particular algorithm is selected to carry
out the evolution, it is necessary that all its parameters, such as
mutation rate, population size, selection mechanisms etc. are tuned in
order to achieve the best results during the evolution process. This
paper investigates the abilities of evolution strategy to evolve digital
logic circuits based on programmable logic array structures when
different mutation rates are used. Several mutation rates (fixed and
variable) are analyzed and compared with each other to outline the
most appropriate choice to be used during the evolution of
combinational logic circuits. The experimental results outlined in this
paper are important as they could be used by every researcher who
might need to use the evolutionary algorithm to design digital logic
circuits.
Abstract: In this paper, a nonconforming mixed finite element method is studied for semilinear pseudo-hyperbolic partial integrodifferential equations. By use of the interpolation technique instead of the generalized elliptic projection, the optimal error estimates of the corresponding unknown function are given.
Abstract: Nowadays, cardiac disease is one of the most common
cause of death. Each year almost one million of angioplasty interventions and stents implantations are made all over the world.
Unfortunately, in 20-30% of cases neointimal proliferations leads to
restenosis occurring within the following period of 3-6 months. Three major factors are believed to contribute mostly to the edge
restenosis: (a) mechanical damage of the artery-s wall caused by the
stent implantation, (b) interaction between the stent and the blood constituents and (c) endothelial growth stimulation by small (lower
that 1.5 Pa) and oscillating wall shear stress. Assuming that this last actor is particularly important, a numerical model of restenosis
basing on wall shear stress distribution in the stented artery was elaborated. A numerical simulations of the development of in-stent
restenosis have been performed and realistic geometric patterns of a
progressing lumen reduction have been obtained
Abstract: The distance protection mainly the impedance relay which is considered as the main protection for transmission lines can be subjected to impedance measurement error which is, mainly, due to the fault resistance and to the power fluctuation. Thus, the impedance relay may not operate for a short circuit at the far end of the protected line (case of the under reach) or operates for a fault beyond its protected zone (case of overreach). In this paper, an approach to fault detection by a distance protection, which distinguishes between the faulty conditions and the effect of overload operation mode, has been developed. This approach is based on the symmetrical components; mainly the negative sequence, and it is taking into account both the effect of fault resistance and the overload situation which both have an effect upon the reliability of the protection in terms of dependability for the former and security for the latter.
Abstract: In this paper, the relationship between learning
motivation and learning performance is explored by using exchange
theory. The relationship is concluded that external performance can
raise learning motivation and then increase learning performance. The
internal performance should be not completely neglected and the
external performance should be not attached important excessively.
The parents need self-study and must be also reeducated. The existing
education must be improved in raise of internal performance. The
incorrect learning thinking will mislead the students, parents, and
educators of next generation, when the students obtain good learning
performance in the learning environment with excess stimulants. Over
operation of external performance will result abnormal learning
thinking and violating learning goal. Learning is not only to obtain
performance. Learning quality and learning performance will be
limited as without learning motivation. The best learning motivation
is, the best learning performance is. The learning for reward is not
good for learning performance. Strategies of promoting life-long
learning are including the encouraging for learner, establishment of
good interaction learning environment, and the advertisement of the
merit and the importance of life-long learning, which can let the
learner with the correct learning motivation.
Abstract: The results show that the bridge equipped with seismic isolation bearing system shows a high amount of energy dissipation. The purpose of the present study is to analyze the overall performance of continuous curved highway viaducts with different bearing supports, with an emphasis on the effectiveness of seismic isolation based on lead rubber bearing and hedge reaction force bearing system consisted of friction sliding bearing and rubber bearing. The bridge seismic performance has been evaluated on six different cases with six bearing models. The effects of the different arrangement of bearing on the deck superstructure displacements, the seismic damage at the bottom of the piers, movement track at the pier-s top and the total and strain energies absorbed by the structure are evaluated. In conclusion, the results provide sufficient evidence of the effectiveness on the use of seismic isolation on steel curved highway bridges.
Abstract: Various intelligences and inspirations have been
adopted into the iterative searching process called as meta-heuristics.
They intelligently perform the exploration and exploitation in the
solution domain space aiming to efficiently seek near optimal
solutions. In this work, the bee algorithm, inspired by the natural
foraging behaviour of honey bees, was adapted to find the near
optimal solutions of the transportation management system, dynamic
multi-zone dispatching. This problem prepares for an uncertainty and
changing customers- demand. In striving to remain competitive,
transportation system should therefore be flexible in order to cope
with the changes of customers- demand in terms of in-bound and outbound
goods and technological innovations. To remain higher service
level but lower cost management via the minimal imbalance scenario,
the rearrangement penalty of the area, in each zone, including time
periods are also included. However, the performance of the algorithm
depends on the appropriate parameters- setting and need to be
determined and analysed before its implementation. BEE parameters
are determined through the linear constrained response surface
optimisation or LCRSOM and weighted centroid modified simplex
methods or WCMSM. Experimental results were analysed in terms
of best solutions found so far, mean and standard deviation on the
imbalance values including the convergence of the solutions
obtained. It was found that the results obtained from the LCRSOM
were better than those using the WCMSM. However, the average
execution time of experimental run using the LCRSOM was longer
than those using the WCMSM. Finally a recommendation of proper
level settings of BEE parameters for some selected problem sizes is
given as a guideline for future applications.
Abstract: An important goal of parboiling is a decrease of rice broken percentage and at the beginning Selected paddy of variety of rice Tarom and soaked at three different temperatures 45 Cº, 65 Cº and 80 Cº orderly for 5 hours, 4 hours and 1.5 hours to moisture of 40 % and then in steaming stage to operate these action two steaming methods are selected steaming under pressure condition and steaming in atmosphere pressure and In the first method after exerting air, the steam pressure is increase to 1 Kg/Cm2 which is done in two different duration times of 2.5 and 5 minutes and in second method used of three times of 5,10 and 15 minutes and dry to 8% moisture and decreases of rice broken percentage at best condition in variety of Tarom of 37.2 % to 7.3 % and increases yield percentage at best condition in variety of Tarom of 69.4 % to 75.93 % and bran percentage decreased in variety of Tarom of 9.53 % to 2.2-3.2 % and this issue cause increases yield percentage in rice and use of This method is very significant for our country because broken percentage of rice in our country is 23-33 %.