Abstract: A human’s hand localization is revised by using radar cross section (RCS) measurements with a minimum root mean square (RMS) error matching algorithm on a touchless keypad mock-up model. RCS and frequency transfer function measurements are carried out in an indoor environment on the frequency ranged from 3.0 to 11.0 GHz to cover federal communications commission (FCC) standards. The touchless keypad model is tested in two different distances between the hand and the keypad. The initial distance of 19.50 cm is identical to the heights of transmitting (Tx) and receiving (Rx) antennas, while the second distance is 29.50 cm from the keypad. Moreover, the effects of Rx angles relative to the hand of human factor are considered. The RCS input parameters are compared with power loss parameters at each frequency. From the results, the performance of the RCS input parameters with the second distance, 29.50 cm at 3 GHz is better than the others.
Abstract: Information security plays a major role in uplifting the standard of secured communications via global media. In this paper, we have suggested a technique of encryption followed by insertion before transmission. Here, we have implemented two different concepts to carry out the above-specified tasks. We have used a two-point crossover technique of the genetic algorithm to facilitate the encryption process. For each of the uniquely identified rows of pixels, different mathematical methodologies are applied for several conditions checking, in order to figure out all the parent pixels on which we perform the crossover operation. This is done by selecting two crossover points within the pixels thereby producing the newly encrypted child pixels, and hence the encrypted cover image. In the next lap, the first and second order derivative operators are evaluated to increase the security and robustness. The last lap further ensures reapplication of the crossover procedure to form the final stego-image. The complexity of this system as a whole is huge, thereby dissuading the third party interferences. Also, the embedding capacity is very high. Therefore, a larger amount of secret image information can be hidden. The imperceptible vision of the obtained stego-image clearly proves the proficiency of this approach.
Abstract: In the process of recovering oil in weak sandstone formations, the strength of sandstones around the wellbore is weakened due to the increase of effective stress/load from the completion activities around the cavity. The weakened and de-bonded sandstone may be eroded away by the produced fluid, which is termed sand production. It is one of the major trending subjects in the petroleum industry because of its significant negative impacts, as well as some observed positive impacts. For efficient sand management therefore, there has been need for a reliable study tool to understand the mechanism of sanding. One method of studying sand production is the use of the widely recognized Discrete Element Method (DEM), Particle Flow Code (PFC3D) which represents sands as granular individual elements bonded together at contact points. However, there is limited knowledge of the particle-scale behavior of the weak sandstone, and the parameters that affect sanding. This paper aims to investigate the reliability of using PFC3D and a simple Darcy flow in understanding the sand production behavior of a weak sandstone. An isotropic tri-axial test on a weak oil sandstone sample was first simulated at a confining stress of 1MPa to calibrate and validate the parallel bond models of PFC3D using a 10m height and 10m diameter solid cylindrical model. The effect of the confining stress on the number of bonds failure was studied using this cylindrical model. With the calibrated data and sample material properties obtained from the tri-axial test, simulations without and with fluid flow were carried out to check on the effect of Darcy flow on bonds failure using the same model geometry. The fluid flow network comprised of every four particles connected with tetrahedral flow pipes with a central pore or flow domain. Parametric studies included the effects of confining stress, and fluid pressure; as well as validating flow rate – permeability relationship to verify Darcy’s fluid flow law. The effect of model size scaling on sanding was also investigated using 4m height, 2m diameter model. The parallel bond model successfully calibrated the sample’s strength of 4.4MPa, showing a sharp peak strength before strain-softening, similar to the behavior of real cemented sandstones. There seems to be an exponential increasing relationship for the bigger model, but a curvilinear shape for the smaller model. The presence of the Darcy flow induced tensile forces and increased the number of broken bonds. For the parametric studies, flow rate has a linear relationship with permeability at constant pressure head. The higher the fluid flow pressure, the higher the number of broken bonds/sanding. The DEM PFC3D is a promising tool to studying the micromechanical behavior of cemented sandstones.
Abstract: During manned exploration of space, missions will require astronaut crewmembers to perform Extra Vehicular Activities (EVAs) for a variety of tasks. These EVAs take place after long periods of operations in space, and in and around unique vehicles, space structures and systems. Considering the remoteness and time spans in which these vehicles will operate, EVA system operations should utilize common worksites, tools and procedures as much as possible to increase the efficiency of training and proficiency in operations. All of the preparations need to be carried out based on studies of astronaut motions. Until now, development and training activities associated with the planned EVAs in Russian and U.S. space programs have relied almost exclusively on physical simulators. These experimental tests are expensive and time consuming. During the past few years a strong increase has been observed in the use of computer simulations due to the fast developments in computer hardware and simulation software. Based on this idea, an effort to develop a computational simulation system to model human dynamic motion for EVA is initiated. This study focuses on the simulation of an astronaut moving the orbital replaceable units into the worksites or removing them from the worksites. Our physics-based methodology helps fill the gap in quantitative analysis of astronaut EVA by providing a multisegment human arm model. Simulation work described in the study improves on the realism of previous efforts, incorporating joint stops to account for the physiological limits of range of motion. To demonstrate the utility of this approach human arm model is simulated virtually using ADAMS/LifeMOD® software. Kinematic mechanism for the astronaut’s task is studied from joint angles and torques. Simulation results obtained is validated with numerical simulation based on the principles of Newton-Euler method. Torques determined using mathematical model are compared among the subjects to know the grace and consistency of the task performed. We conclude that due to uncertain nature of exploration-class EVA, a virtual model developed using multibody dynamics approach offers significant advantages over traditional human modeling approaches.
Abstract: Municipal Solid Waste (MSW) disposed in landfill sites decompose under anaerobic conditions and produce gases which mainly contain carbon dioxide (CO2) and methane (CH4). Methane has the potential of causing global warming 25 times more than CO2, and can potentially affect human life and environment. Thus, this research aims to determine MSW generation and the annual CH4 emissions from the generated waste in Oman over the years 1971-2030. The estimation of total waste generation was performed using existing models, while the CH4 emissions estimation was performed using the intergovernmental panel on climate change (IPCC) default method. It is found that total MSW generation in Oman might be reached 3,089 Gg in the year 2030, which approximately produced 85 Gg of CH4 emissions in the year 2030.
Abstract: Control of diesel engine’s air path has drawn a lot of attention due to its multi input-multi output, closed coupled, non-linear relation. Today, precise control of amount of air to be combusted is a must in order to meet with tight emission limits and performance targets. In this study, passenger car size diesel engine is modeled by AVL Boost RT, and then simulated with standard, industry level PID controllers. Finally, linear model predictive control is designed and simulated. This study shows the importance of modeling and control of diesel engines with flexible algorithm development in computer based systems.
Abstract: The new methods as accelerated steam distillation
assisted by microwave (ASDAM) is a combination of microwave
heating and steam distillation, performed at atmospheric pressure at
very short extraction time. Isolation and concentration of volatile
compounds are performed by a single stage. (ASDAM) has been
compared with (ASDAM) with cryogrinding of seeds (CG) and a
conventional technique, hydrodistillation assisted by microwave
(HDAM), hydro-distillation (HD) for the extraction of essential oil
from aromatic herb as caraway and cumin seeds. The essential oils
extracted by (ASDAM) for 1 min were quantitatively (yield) and
qualitatively (aromatic profile) no similar to those obtained by
ASDAM-CG (1 min) and HD (for 3 h). The accelerated microwave
extraction with cryogrinding inhibits numerous enzymatic reactions
as hydrolysis of oils.
Microwave radiations constitute the adequate mean for the
extraction operations from the yields and high content in major
component majority point view, and allow to minimise considerably
the energy consumption, but especially heating time too, which is one
of essential parameters of artifacts formation.
The ASDAM and ASDAM-CG are green techniques and yields an
essential oil with higher amounts of more valuable oxygenated
compounds comparable to the biosynthesis compounds, and allows
substantial savings of costs, in terms of time, energy and plant
material.
Abstract: This study attempts to consider the linkage between management and computer sciences in order to develop the software named “IntelSymb” as a demo application to prove data analysis of non-energy* fields’ diversification, which will positively influence on energy dependency mitigation of countries. Afterward, we analyzed 18 years of economic fields of development (5 sectors) of 13 countries by identifying which patterns mostly prevailed and which can be dominant in the near future. To make our analysis solid and plausible, as a future work, we suggest developing a gateway or interface, which will be connected to all available on-line data bases (WB, UN, OECD, U.S. EIA) for countries’ analysis by fields. Sample data consists of energy (TPES and energy import indicators) and non-energy industries’ (Main Science and Technology Indicator, Internet user index, and Sales and Production indicators) statistics from 13 OECD countries over 18 years (1995-2012). Our results show that the diversification of non-energy industries can have a positive effect on energy sector dependency (energy consumption and import dependence on crude oil) deceleration. These results can provide empirical and practical support for energy and non-energy industries diversification’ policies, such as the promoting of Information and Communication Technologies (ICTs), services and innovative technologies efficiency and management, in other OECD and non-OECD member states with similar energy utilization patterns and policies. Industries, including the ICT sector, generate around 4 percent of total GHG, but this is much higher — around 14 percent — if indirect energy use is included. The ICT sector itself (excluding the broadcasting sector) contributes approximately 2 percent of global GHG emissions, at just under 1 gigatonne of carbon dioxide equivalent (GtCO2eq). Ergo, this can be a good example and lesson for countries which are dependent and independent on energy, and mainly emerging oil-based economies, as well as to motivate non-energy industries diversification in order to be ready to energy crisis and to be able to face any economic crisis as well.
Abstract: Optimisation of the physical and mechanical properties of cold rolled thin strips is achieved by controlling the rolling parameters. In this paper, the factors affecting the asymmetrical cold rolling of thin low carbon steel strip have been studied at a speed ratio of 1.1 without lubricant applied. The effect of rolling parameters on the resulting microstructure was also investigated. It was found that under dry condition, work roll shifting and work roll cross angle can improve the strip profile, and the result is more significant with an increase of work roll cross angle rather than that of work roll shifting. However, there was no obvious change in microstructure. In addition, effects of rolling parameters on strip profile and microstructure have also been discussed.
Abstract: The sun is an inexhaustible source and harness its potential both for heating and power generation is one of the most promising and necessary alternatives, mainly due to environmental issues. However, it should be noted that this has always been present in the generation of energy on earth, only indirectly, since it is responsible for virtually all other energy sources, such as generating source of evaporation of the water cycle, allowing the impoundment and the consequent generation of electricity (hydroelectric power); winds are caused by atmospheric induction caused by large scale solar radiation; petroleum, coal and natural gas were generated from waste plants and animals that originally derived energy required for their development of solar radiation. This paper presents a study on the feasibility of using solar energy for water heating in homes. A simplified methodology developed for formulation of solar heating operation model of water in alternative systems of solar energy in Brazil, and compared it to that in the international market. Across this research, it was possible to create new paradigms for alternative applications to the use of solar energy.
Abstract: This study was conducted for the investigation of
number of cellulolytic bacteria and their ability in decomposition.
Seven samples surface soil were collected on cellulose Zailiskii
Alatau slopes. Cellulolitic activity of new strains of Bacillus, isolated
from soil is determined. Isolated cellulose degrading bacteria were
screened for determination of the highest cellulose activity by
quantitative assay using Congo red, gravimetric assay and
colorimetric DNS method trough of the determination of the
parameters of sugar reduction. Strains are assigned to: B.subtilis,
B.licheniformis, B. cereus and, В. megaterium. Bacillus strains
consisting of several different types of cellulases have broad substrate
specificity of cellulase complexes formed by them. Cellulolitic
bacteria were recorded to have highest cellulase activity and selected
for optimization of cellulase enzyme production.
Abstract: In Ultra high-field MRI scanners (3T and higher),
parallel RF transmission techniques using multiple RF chains with
multiple transmit elements are a promising approach to overcome
the high-field MRI challenges in terms of inhomogeneity in the RF
magnetic field and SAR. However, mutual coupling between the
transmit array elements disturbs the desirable independent control of
the RF waveforms for each element. This contribution demonstrates
a 18 dB improvement of decoupling (isolation) performance due to
the very low output impedance of our 1 kW power amplifier.
Abstract: Liver cancer is one of the common diseases that cause the death. Early detection is important to diagnose and reduce the incidence of death. Improvements in medical imaging and image processing techniques have significantly enhanced interpretation of medical images. Computer-Aided Diagnosis (CAD) systems based on these techniques play a vital role in the early detection of liver disease and hence reduce liver cancer death rate. This paper presents an automated CAD system consists of three stages; firstly, automatic liver segmentation and lesion’s detection. Secondly, extracting features. Finally, classifying liver lesions into benign and malignant by using the novel contrasting feature-difference approach. Several types of intensity, texture features are extracted from both; the lesion area and its surrounding normal liver tissue. The difference between the features of both areas is then used as the new lesion descriptors. Machine learning classifiers are then trained on the new descriptors to automatically classify liver lesions into benign or malignant. The experimental results show promising improvements. Moreover, the proposed approach can overcome the problems of varying ranges of intensity and textures between patients, demographics, and imaging devices and settings.
Abstract: This study aims to investigate and explore the underlying causes of security concerns of customers emerged when WHSmith transformed its physical system to virtualized business model through NetSuite. NetSuite is essentially fully integrated software which helps transforming the physical system to virtualized business model. Modern organisations are moving away from traditional business models to cloud based models and consequently it is expected to have a better, secure and innovative environment for customers. The vital issue of the modern age race is the security when transforming virtualized through cloud based models and designers of interactive systems often misunderstand privacy and even often ignore it, thus causing concerns for users. The content analysis approach is being used to collect the qualitative data from 120 online bloggers including TRUSTPILOT. The results and finding provide useful new insights into the nature and form of security concerns of online users after they have used the WHSmith services offered online through their website. Findings have theoretical as well as practical implications for the successful adoption of cloud computing Business-to-Business model and similar systems.
Abstract: This study examined the digital preservation in
Nigeria university libraries. A comparison between the university of
Nigeria Nsukka (UNN) and Ahmadu Bello University Zaria (ABU,
Zaria). The study utilized primary source of data obtained from two
selected institution librarians. Finding revealed varying results in
terms of skills acquired by librarians before and after digitization of
the two institutions. The study reports that journals publication, text
book, CD-ROMS, conference papers and proceedings, theses,
dissertations and seminar papers are among the information resources
available for digitization. The study further documents that copyright
issue, power failure, and unavailability of needed materials are
among the challenges facing the digitization of library of the
institution. On the basis of the finding, the study concluded that
digitization of library enhances efficiency in organization and
retrieval of information services. The study therefore recommended
that software should be upgraded with backup, training of the
librarians on digital process, installation of antivirus and
enhancement of technical collaboration between the library and MIS.
Abstract: The new design of heat exchangers utilizing an
annular distributor opens a new gateway for realizing higher energy
optimization. To realize this goal, graphene nanoplatelet-based water
nanofluids with promising thermophysical properties were
synthesized in the presence of covalent and noncovalent
functionalization. Thermal conductivity, density, viscosity and
specific heat capacity were investigated and employed as a raw data
for ANSYS-Fluent to be used in two-phase approach. After
validation of obtained results by analytical equations, two special
parameters of convective heat transfer coefficient and pressure drop
were investigated. The study followed by studying other heat transfer
parameters of annular pass in the presence of graphene nanopletelesbased
water nanofluids at different weight concentrations, input
powers and temperatures. As a result, heat transfer performance and
friction loss are predicted for both synthesized nanofluids.
Abstract: Comparative analysis of robotic vehicles for pipe inspection is presented in this paper. The promising concept of self-propelled intelligent robotic vehicle (SPIRV) based on octahedral dodekapod for inspection and operation in active branched pipelines with variable cross-sections is reasoned. SPIRV is able to move in pipeline, regardless of its spatial orientation. SPIRV can also be used to move along the outside of the pipelines as well as in space between surfaces of annular tubes. Every one of faces of the octahedral dodekapod can clamp/unclamp a thing with a closed loop surface of various forms as well as put pressure on environmental surface of contact. These properties open new possibilities for its applications in SPIRV. We examine design principles of octahedral dodekapod as future intelligent building blocks for various robotic vehicles that can self-move and self-reconfigure.
Abstract: The present study is based on the three-dimensional digital analysis by the finite elements method of the mechanical loading effect on the delamination of unidirectional and multidirectional stratified composites. The aim of this work is the determination of the release energy rate G in mode I and the Von Mises equivalent constraint distribution along the damaged area under the influence of several parameters such as the applied load and the delamination size. The results obtained in this study show that the unidirectional composite laminates have better mechanical resistance one the loading line than the multidirectional composite laminates.
Abstract: Despite the benefits of innovation diffusion in the
South African public service, implementation thereof seems to be
problematic, particularly with regard to e-governance which would
enhance the quality of service delivery, especially accessibility,
choice, and mode of operation. This paper reports on differences
between the public service and the private sector in terms of
innovation diffusion. Innovation diffusion will be investigated to
explore identified obstacles that are hindering successful
implementation of e-governance. The research inquiry is underpinned
by the diffusion of innovation theory, which is premised on the
assumption that innovation has a distinct channel, time, and mode of
adoption within the organisation. A comparative thematic document
analysis was conducted to investigate organisational differences with
regard to innovation diffusion. A similar approach has been followed
in other countries, where the same conceptual framework has been
used to guide document analysis in studies in both the private and the
public sectors. As per the recommended conceptual framework, three
organisational characteristics were emphasised, namely the external
characteristics of the organisation, the organisational structure, and
the inherent characteristics of the leadership. The results indicated
that the main difference in the external characteristics lies in the
focus and the clientele of the private sector. With regard to
organisational structure, private organisations have veto power,
which is not the case in the public service. Regarding leadership,
similarities were observed in social and environmental responsibility
and employees’ attitudes towards immediate supervision. Differences
identified included risk taking, the adequacy of leadership
development, organisational approaches to motivation and
involvement in decision making, and leadership style. Due to the
organisational differences observed, it is recommended that
differentiated strategies be employed to ensure effective innovation
diffusion, and ultimately e-governance. It is recommended that the
results of this research be used to stimulate discussion on ways to
improve collaboration between the mentioned sectors, to capitalise on
the benefits of each sector.
Abstract: In this paper, an attempt has been made to analyze the effect of wall window orientation on Daylight Illuminance Ratio (DIR) and energy saving in a building known as “SODHA BERS COMPLEX (SBC)” at Varanasi, UP, India. The building has been designed incorporating all passive concepts for thermal comfort as well daylighting concepts to maximize the use of natural daylighting for the occupants in the day to day activities. The annual average DIR and the energy saving has been estimated by using the DIR model for wall window with different orientations under clear sky condition. It has been found that for south oriented window the energy saving per square meter is more compared to the other orientations due to the higher level of solar insolation for the south window in northern hemisphere whereas energy saving potential is minimum for north oriented wall window. The energy saving potential was 26%, 81% and 51% higher for east, south and west oriented window in comparison to north oriented window. The average annual DIR has same trends of variation as the annual energy saving and it is maximum for south oriented window and minimum for north oriented window.