Abstract: Atmospheric stability plays the most important role in
the transport and dispersion of air pollutants. Different methods are
used for stability determination with varying degrees of complexity.
Most of these methods are based on the relative magnitude of
convective and mechanical turbulence in atmospheric motions.
Richardson number, Monin-Obukhov length, Pasquill-Gifford
stability classification and Pasquill–Turner stability classification, are
the most common parameters and methods. The Pasquill–Turner
Method (PTM), which is employed in this study, makes use of
observations of wind speed, insolation and the time of day to classify
atmospheric stability with distinguishable indices. In this study, a
model is presented to determination of atmospheric stability
conditions using PTM. As a case study, meteorological data of
Mehrabad station in Tehran from 2000 to 2005 is applied to model.
Here, three different categories are considered to deduce the pattern
of stability conditions. First, the total pattern of stability classification
is obtained and results show that atmosphere is 38.77%, 27.26%,
33.97%, at stable, neutral and unstable condition, respectively. It is
also observed that days are mostly unstable (66.50%) while nights are
mostly stable (72.55%). Second, monthly and seasonal patterns are
derived and results indicate that relative frequency of stable
conditions decrease during January to June and increase during June
to December, while results for unstable conditions are exactly in
opposite manner. Autumn is the most stable season with relative
frequency of 50.69% for stable condition, whilst, it is 42.79%,
34.38% and 27.08% for winter, summer and spring, respectively.
Hourly stability pattern is the third category that points out that
unstable condition is dominant from approximately 03-15 GTM and
04-12 GTM for warm and cold seasons, respectively. Finally,
correlation between atmospheric stability and CO concentration is
achieved.
Abstract: This experiment discusses the effects of fracture
parameters such as depth, length, width, angle and the number of the
fracture to the conductance properties of laterite using the DUK-2B
digital electrical measurement system combined with the method of
simulating the fractures. The results of experiment show that the
changes of fracture parameters produce effects to the conductance
properties of laterite. There is a clear degressive period of the
conductivity of laterite during increasing the depth, length, width, or
the angle and the quantity of fracture gradually. When the depth of
fracture exceeds the half thickness of the soil body, the conductivity of
laterite shows evidently non-linear diminishing pattern and the
amplitude of decrease tends to increase. The length of fracture has
fewer effects than the depth to the conductivity. When the width of
fracture reaches some fixed values, the change of the conductivity is
less sensitive to the change of the width, and at this time, the
conductivity of laterite maintains at a stable level. When the angle of
fracture is less than 45°, the decrease of the conductivity is more
clearly as the angle increases. But when angle is more than 45°,
change of the conductivity is relatively gentle as the angle increases.
The increasing quantity of the fracture causes the other fracture
parameters having great impact on the change of conductivity. When
moisture content and temperature were unchanged, depth and angle of
fractures are the major factors affecting the conductivity of laterite
soil; quantity, length, and width are minor influencing factors. The
sensitivity of fracture parameters affect conductivity of laterite soil is:
depth >angles >quantity >length >width.
Abstract: In the current Grid environment, efficient workload
management presents a significant challenge, for which there are
exorbitant de facto standards encompassing resource discovery,
brokerage, and data transfer, among others. In addition, the real-time
resource status, essential for an optimal resource allocation strategy,
is often not readily accessible. To address these issues and provide a
cleaner abstraction of the Grid with the potential of generalizing into
arbitrary resource-sharing environment, this paper proposes a new
Condor-based pilot mechanism applied in the PanDA architecture,
PanDA-PF WMS, with the goal of providing a more generic yet
efficient resource allocating strategy. In this architecture, the PanDA
server primarily acts as a repository of user jobs, responding to pilot
requests from distributed, remote resources. Scheduling decisions are
subsequently made according to the real-time resource information
reported by pilots. Pilot Factory is a Condor-inspired solution for a
scalable pilot dissemination and effectively functions as a resource
provisioning mechanism through which the user-job server, PanDA,
reaches out to the candidate resources only on demand.
Abstract: Cutting tools are widely used in manufacturing processes and drilling is the most commonly used machining process. Although drill-bits used in drilling may not be expensive, their breakage can cause damage to expensive work piece being drilled and at the same time has major impact on productivity. Predicting drill-bit breakage, therefore, is important in reducing cost and improving productivity. This study uses twenty features extracted from two degradation signals viz., thrust force and torque. The methodology used involves developing and comparing decision tree, random forest, and multinomial logistic regression models for classifying and predicting drill-bit breakage using degradation signals.
Abstract: Selecting the data modeling technique for an
information system is determined by the objective of the resultant
data model. Dimensional modeling is the preferred modeling
technique for data destined for data warehouses and data mining,
presenting data models that ease analysis and queries which are in
contrast with entity relationship modeling. The establishment of data
warehouses as components of information system landscapes in
many organizations has subsequently led to the development of
dimensional modeling. This has been significantly more developed
and reported for the commercial database management systems as
compared to the open sources thereby making it less affordable for
those in resource constrained settings. This paper presents
dimensional modeling of HIV patient information using open source
modeling tools. It aims to take advantage of the fact that the most
affected regions by the HIV virus are also heavily resource
constrained (sub-Saharan Africa) whereas having large quantities of
HIV data. Two HIV data source systems were studied to identify
appropriate dimensions and facts these were then modeled using two
open source dimensional modeling tools. Use of open source would
reduce the software costs for dimensional modeling and in turn make
data warehousing and data mining more feasible even for those in
resource constrained settings but with data available.
Abstract: Importance of environmental efficiency of electric power industry stems from high demand for energy combined with global warming concerns. It is especially essential for the world largest economies like that of the United States. The paper introduces a Data Envelopment Analysis (DEA) model of environmental efficiency using indicators of fossil fuels utilization, emissions rate, and electric power losses. Using DEA is advantageous in this situation over other approaches due to its nonparametric nature. The paper analyzes data for the period of 1990 - 2006 by comparing actual yearly levels in each dimension with the best values of partial indicators for the period. As positive factors of efficiency, tendency to the decline in emissions rates starting 2000, and in electric power losses starting 2004 may be mentioned together with increasing trend of fuel utilization starting 1999. As a result, dynamics of environmental efficiency is positive starting 2002. The main concern is the decline in fossil fuels utilization in 2006. This negative change should be reversed to comply with ecological and economic requirements.
Abstract: Scarcity of water resources and huge costs of
establishing new hydraulic installations necessitate optimal
exploitation from existing reservoirs. Sustainable management and
efficient exploitation from existing finite water resources are
important factors in water resource management, particularly in the
periods of water insufficiency and in dry regions, and on account of
competitive allocations in the view of exploitation management. This
study aims to minimize reservoir water release from a determined
rate of demand. A numerical model for water optimal exploitation
has been developed using GAMS introduced by the World Bank and
applied to the case of Meijaran dam, northern Iran. The results
indicate that this model can optimize the function of reservoir
exploitation while required water for lower parts of the region will be
supplied. Further, allocating optimal water from reservoir, the
optimal rate of water allocated to any group of the users were
specified to increase benefits in curve dam exploitation.
Abstract: It is important to provide possibility of so called
“handover" for the mobile subscriber from GSM network to Wi-Fi
network and back. To solve specified problem it is necessary to
estimate connection time between base station and wireless access
point. Difficulty to estimate this parameter is that it doesn-t described
in specifications of the standard and, hence, no recommended value
is given.
In this paper, the analytical model is presented that allows the
estimating connection time between base station and IEEE 802.11
access point.
Abstract: Fatigue behaviors of Lead Zirconate Titanate (PZT)
ceramics under different amplitude of bipolar electrical loads have
been investigated. Fatigue behavior is represented by the change of
hysteresis loops and remnant polarization. Three levels of electrical
load amplitudes (1.00, 1.25 and 1.50 kV /mm) were applied in this
experimental. It was found that the remnant polarization decreased
significantly with the number of loading cycles. The degree of fatigue
degradation depends on the amplitude of electric field. The higher
amplitude exhibits the greater fatigue degradation.
Abstract: This paper presents an alternative strategy of queuing
handover called Pseudo Last Useful Instant PLUI scheme for Low
Earth Orbit Mobile Satellite Systems LEO MSSs. The PLUI scheme
uses the same approach as the Last Useful Instant LUI scheme
previously proposed in literature, with less complex implementation.
Simulation tests were carried out using Dynamic Channel Allocation
DCA in order to evaluate the performance of this scheme and also an
analytical approach has been presented to allow the performance
evaluation of Fixed Channel Allocation FCA, with different
handover queuing disciplines. The results show that performances
achieved by the proposed strategy are close to those achieved using
the LUI scheme.
Abstract: A new method identifies coupled fluid-structure system with a reduced set of state variables is presented. Assuming that the structural model is known a priori either from an analysis or a test and using linear transformations between structural and aeroelastic states, it is possible to deduce aerodynamic information from sampled time histories of the aeroelastic system. More specifically given a finite set of structural modes the method extracts generalized aerodynamic force matrix corresponding to these mode shapes. Once the aerodynamic forces are known, an aeroelastic reduced-order model can be constructed in discrete-time, state-space format by coupling the structural model and the aerodynamic system. The resulting reduced-order model is suitable for constant Mach, varying density analysis.
Abstract: The purpose of this study was to investigate relationships between satisfaction with major and career decision efficacy and career attitude maturity of engineering college students by performing correlation analysis. Gender differences in between satisfaction with major and career decision efficacy and career attitude maturity were also examined by T-test. The results T-test revealed gender differences in only career decision efficacy. Male Students scored significantly higher than did female students on career decision efficacy and satisfaction with major. The results of correlation analysis showed a) satisfaction with major were significantly associated with career decision efficacy, b) satisfaction with major were significantly associated with career attitude maturity, and c) career decision efficacy were significantly associated with career attitude maturity. As a result,we found the importance of satisfaction in engineering college students- major studies when deciding their career.
Abstract: Recently, there are significant improvements in the
capabilities of mobile devices; rendering large terrain is tedious
because of the constraint in resources of mobile devices. This
paper focuses on the implementation of terrain rendering on
mobile device to observe some issues and current constraints
occurred. Experiments are performed using two datasets with
results based on rendering speed and appearance to ascertain both
the issues and constraints. The result shows a downfall of frame
rate performance because of the increase of triangles. Since the
resolution between computer and mobile device is different, the
terrain surface on mobile device looks more unrealistic compared
to on a computer. Thus, more attention in the development of
terrain rendering on mobile devices is required. The problems
highlighted in this paper will be the focus of future research and
will be a great importance for 3D visualization on mobile device.
Abstract: Benefits to the organisation are just as important as technical ability when it comes to software success. The challenge is to provide industry with professionals who understand this. In other words: How to teach computer engineering students to look beyond technology, and at the benefits of software to organizations? This paper reports on the conceptual design of a section of the computer networks module aimed to sensitize the students to the organisational context.
Checkland focuses on different worldviews represented by various role players in the organisation. He developed the Soft Systems Methodology that guides purposeful action in organisations, while incorporating different worldviews in the modeling process. If we can sensitize students to these methods, they are likely to appreciate the wider context of application of system software. This paper will provide literature on these concepts as well as detail on how the students will be guided to adopt these concepts.
Abstract: In this research, a biofiltration process to remove
ammonia gas from gas stream using agricultural residue biofilter
medias is studied. The experiments were conducted in laboratoryscale
biofilter. The biofilter medias were a mixture of manure
fertilizer and bagasse at various ratios i.e., 1:3, 1:5 and 1:7. The
experiments were performed for a period of 40 days. The empty bed
retention time (EBRT) is 78s. The moisture content of biofilter media
was maintained at 45-60% using water. The results showed that the
agricultural residues (manure fertilizer and bagasse) are suitable as
biofilter media for ammonia gas removal in biofiltration process.
The maximum efficiency of ammonia gas removal is observed
from the 1:5 of manure fertilizer: bagasse ratio at 89.93%. The
biofiltration is more effective at low ammonia gas concentration. In
addition, the mixture ratio of biofilter media is not a significant factor
in biofiltration operation while the most significant factor for
biofiltration operation is the inlet ammonia gas concentration.
Abstract: During last decades is widely discussed the
international harmonization of financial reporting. This
harmonization is also affected by national tax systems in analyzed
countries. This paper provides some evidence on current national tax
systems in selected countries in Central and Eastern Europe. The
linkage of accounting profit as a tax base might decrease the
administrative burden for majority of SMEs, which are the most
important engine of each national economy.
Abstract: The aim of this paper is to examine factors related to system environment (namely, system quality and vendor support) that influences ERP implementation success in Iranian companies. Implementation success is identified using user satisfaction and organizational impact perspective. The study adopts the survey questionnaire approach to collect empirical data. The questionnaire was distributed to ERP users and a total of 384 responses were used for analysis. The results illustrated that both system quality and vendor support have significant effect on ERP implementation success. This implies that companies must ensure they source for the best available system and a vendor that is dependable, reliable and trustworthy.
Abstract: This article presents a current-mode universal biquadratic filter. The proposed circuit can apparently provide standard functions of the biquad filter: low-pass, high-pass, bandpass, band-reject and all-pass functions. The circuit uses 4 current controlled transconductance amplifiers (CCTAs) and 2 grounded capacitors. In addition, the pole frequency and quality factor can be adjusted by electronic method by adjusting the bias currents of the CCTA. The proposed circuit uses only grounded capacitors without additional external resistors, the proposed circuit is considerably appropriate to further developing into an integrated circuit. The results of PSPICE simulation program are corresponding to the theoretical analysis.
Abstract: Avoidable unscheduled maintenance events and unnecessary
spare parts deliveries are mostly caused by an incorrect choice
of the underlying maintenance strategy. For a faster and more efficient
supply of spare parts for aircrafts of an airline we examine options for
improving the underlying logistics network integrated in an existing
aviation industry network. This paper presents a dynamic prediction
model as decision support for maintenance method selection considering
requirements of an entire flight network. The objective is
to guarantee a high supply of spare parts by an optimal interaction
of various network levels and thus to reduce unscheduled maintenance
events and minimize total costs. By using a prognostics-based
preventive maintenance strategy unscheduled component failures are
avoided for an increase in availability and reliability of the entire
system. The model is intended for use in an aviation company that
utilizes a structured planning process based on collected failures data
of components.
Abstract: e-mail has become an important means of electronic
communication but the viability of its usage is marred by Unsolicited
Bulk e-mail (UBE) messages. UBE consists of many types
like pornographic, virus infected and 'cry-for-help' messages as well
as fake and fraudulent offers for jobs, winnings and medicines. UBE
poses technical and socio-economic challenges to usage of e-mails.
To meet this challenge and combat this menace, we need to
understand UBE. Towards this end, the current paper presents a
content-based textual analysis of more than 2700 body enhancement
medicinal UBE. Technically, this is an application of Text Parsing
and Tokenization for an un-structured textual document and we
approach it using Bag Of Words (BOW) and Vector Space Document
Model techniques. We have attempted to identify the most
frequently occurring lexis in the UBE documents that advertise
various products for body enhancement. The analysis of such top
100 lexis is also presented. We exhibit the relationship between
occurrence of a word from the identified lexis-set in the given UBE
and the probability that the given UBE will be the one advertising for
fake medicinal product. To the best of our knowledge and survey of
related literature, this is the first formal attempt for identification of
most frequently occurring lexis in such UBE by its textual analysis.
Finally, this is a sincere attempt to bring about alertness against and
mitigate the threat of such luring but fake UBE.