Abstract: This paper investigates the effects of knowledge-based acceleration feedback control integrated with Automatic Generation Control (AGC) to enhance the quality of frequency control of governing system. The Intelligent Acceleration Feedback Controller (IAFC) is proposed to counter the over and under frequency occurrences due to major load change in power system network. Therefore, generator tripping and load shedding operations can be reduced. Meanwhile, the integration of IAFC with AGC, a well known Load-Frequency Control (LFC) is essential to ensure the system frequency is restored to the nominal value. Computer simulations of frequency response of governing system are used to optimize the parameters of IAFC. As a result, there is substantial improvement on the LFC of governing system that employing the proposed control strategy.
Abstract: One of the most important power quality issues is voltage flicker. Nowadays this issue also impacts the power system all over the world. The fact of the matter is that the more and the larger capacity of wind generator has been installed. Under unstable wind power situation, the variation of output current and voltage have caused trouble to voltage flicker. Hence, the major purpose of this study is to analyze the impact of wind generator on voltage flicker of power system. First of all, digital simulation and analysis are carried out based on wind generator operating under various system short circuit capacity, impedance angle, loading, and power factor of load. The simulation results have been confirmed by field measurements.
Abstract: System development life cycle (SDLC) is a
process uses during the development of any system. SDLC
consists of four main phases: analysis, design, implement and
testing. During analysis phase, context diagram and data flow
diagrams are used to produce the process model of a system.
A consistency of the context diagram to lower-level data flow
diagrams is very important in smoothing up developing
process of a system. However, manual consistency check from
context diagram to lower-level data flow diagrams by using a
checklist is time-consuming process. At the same time, the
limitation of human ability to validate the errors is one of the
factors that influence the correctness and balancing of the
diagrams. This paper presents a tool that automates the
consistency check between Data Flow Diagrams (DFDs)
based on the rules of DFDs. The tool serves two purposes: as
an editor to draw the diagrams and as a checker to check the
correctness of the diagrams drawn. The consistency check
from context diagram to lower-level data flow diagrams is
embedded inside the tool to overcome the manual checking
problem.
Abstract: This research explores on the development of the structure of Carbon Credit Registry System those accords to the need of future events in Thailand. This research also explores the big picture of every connected system by referring to the design of each system, the Data Flow Diagram, and the design in term of the system-s data using DES standard. The purpose of this paper is to show how to design the model of each system. Furthermore, this paper can serve as guideline for designing an appropriate Carbon Credit Registry System.
Abstract: Image compression plays a vital role in today-s
communication. The limitation in allocated bandwidth leads to
slower communication. To exchange the rate of transmission in the
limited bandwidth the Image data must be compressed before
transmission. Basically there are two types of compressions, 1)
LOSSY compression and 2) LOSSLESS compression. Lossy
compression though gives more compression compared to lossless
compression; the accuracy in retrievation is less in case of lossy
compression as compared to lossless compression. JPEG, JPEG2000
image compression system follows huffman coding for image
compression. JPEG 2000 coding system use wavelet transform,
which decompose the image into different levels, where the
coefficient in each sub band are uncorrelated from coefficient of
other sub bands. Embedded Zero tree wavelet (EZW) coding exploits
the multi-resolution properties of the wavelet transform to give a
computationally simple algorithm with better performance compared
to existing wavelet transforms. For further improvement of
compression applications other coding methods were recently been
suggested. An ANN base approach is one such method. Artificial
Neural Network has been applied to many problems in image
processing and has demonstrated their superiority over classical
methods when dealing with noisy or incomplete data for image
compression applications. The performance analysis of different
images is proposed with an analysis of EZW coding system with
Error Backpropagation algorithm. The implementation and analysis
shows approximately 30% more accuracy in retrieved image
compare to the existing EZW coding system.
Abstract: In recent years multi-agent systems have emerged as one of the interesting architectures facilitating distributed collaboration and distributed problem solving. Each node (agent) of the network might pursue its own agenda, exploit its environment, develop its own problem solving strategy and establish required communication strategies. Within each node of the network, one could encounter a diversity of problem-solving approaches. Quite commonly the agents can realize their processing at the level of information granules that is the most suitable from their local points of view. Information granules can come at various levels of granularity. Each agent could exploit a certain formalism of information granulation engaging a machinery of fuzzy sets, interval analysis, rough sets, just to name a few dominant technologies of granular computing. Having this in mind, arises a fundamental issue of forming effective interaction linkages between the agents so that they fully broadcast their findings and benefit from interacting with others.
Abstract: Artificial Intelligence based gaming is an interesting topic in the state-of-art technology. This paper presents an automation of a tradition Omani game, called Al-Hawalees. Its related issues are resolved and implemented using artificial intelligence approach. An AI approach called mini-max procedure is incorporated to make a diverse budges of the on-line gaming. If number of moves increase, time complexity will be increased in terms of propositionally. In order to tackle the time and space complexities, we have employed a back propagation neural network (BPNN) to train in off-line to make a decision for resources required to fulfill the automation of the game. We have utilized Leverberg- Marquardt training in order to get the rapid response during the gaming. A set of optimal moves is determined by the on-line back propagation training fashioned with alpha-beta pruning. The results and analyses reveal that the proposed scheme will be easily incorporated in the on-line scenario with one player against the system.
Abstract: At present, it is very common to find renewable
energy resources, especially wind power, connected to distribution
systems. The impact of this wind power on voltage distribution levels
has been addressed in the literature. The majority of this works deals
with the determination of the maximum active and reactive power
that is possible to be connected on a system load bus, until the
voltage at that bus reaches the voltage collapse point. It is done by the
traditional methods of PV curves reported in many references.
Theoretical expression of maximum power limited by voltage
stability transfer through a grid is formulated using an exact
representation of distribution line with ABCD parameters. The
expression is used to plot PV curves at various power factors of a
radial system. Limited values of reactive power can be obtained. This
paper presents a method to study the relationship between the active
power and voltage (PV) at the load bus to identify the voltage
stability limit. It is a foundation to build a permitted working
operation region in complying with the voltage stability limit at the
point of common coupling (PCC) connected wind farm.
Abstract: Design and implementation of a novel B-ACOSD CFAR algorithm is presented in this paper. It is proposed for detecting radar target in log-normal distribution environment. The BACOSD detector is capable to detect automatically the number interference target in the reference cells and detect the real target by an adaptive threshold. The detector is implemented as a System on Chip on FPGA Altera Stratix II using parallelism and pipelining technique. For a reference window of length 16 cells, the experimental results showed that the processor works properly with a processing speed up to 115.13MHz and processing time0.29 ┬Ás, thus meets real-time requirement for a typical radar system.
Abstract: Conventional WBL is effective for meaningful student, because rote student learn by repeating without thinking or trying to understand. It is impossible to have full benefit from conventional WBL. Understanding of rote student-s intention and what influences it becomes important. Poorly designed user interface will discourage rote student-s cultivation and intention to use WBL. Thus, user interface design is an important factor especially when WBL is used as comprehensive replacement of conventional teaching. This research proposes the influencing factors that can enhance student-s intention to use the system. The enhanced TAM is used for evaluating the proposed factors. The research result points out that factors influencing rote student-s intention are Perceived Usefulness of Homepage Content Structure, Perceived User Friendly Interface, Perceived Hedonic Component, and Perceived (homepage) Visual Attractiveness.
Abstract: In this paper, an automatic detecting algorithm for
QRS complex detecting was applied for analyzing ECG recordings
and five criteria for dangerous arrhythmia diagnosing are applied for a
protocol type of automatic arrhythmia diagnosing system. The
automatic detecting algorithm applied in this paper detected the
distribution of QRS complexes in ECG recordings and related
information, such as heart rate and RR interval. In this investigation,
twenty sampled ECG recordings of patients with different pathologic
conditions were collected for off-line analysis. A combinative
application of four digital filters for bettering ECG signals and
promoting detecting rate for QRS complex was proposed as
pre-processing. Both of hardware filters and digital filters were
applied to eliminate different types of noises mixed with ECG
recordings. Then, an automatic detecting algorithm of QRS complex
was applied for verifying the distribution of QRS complex. Finally,
the quantitative clinic criteria for diagnosing arrhythmia were
programmed in a practical application for automatic arrhythmia
diagnosing as a post-processor. The results of diagnoses by automatic
dangerous arrhythmia diagnosing were compared with the results of
off-line diagnoses by experienced clinic physicians. The results of
comparison showed the application of automatic dangerous
arrhythmia diagnosis performed a matching rate of 95% compared
with an experienced physician-s diagnoses.
Abstract: The separation efficiency of a hydrocyclone has
extensively been considered on the rigid particle assumption. A
collection of experimental studies have demonstrated their
discrepancies from the modeling and simulation results. These
discrepancies caused by the actual particle elasticity have generally
led to a larger amount of energy consumption in the separation
process. In this paper, the influence of particle elasticity on the
separation efficiency of a hydrocyclone system was investigated
through the Finite Element (FE) simulations using crude oil droplets
as the elastic particles. A Reitema-s design hydrocyclone with a
diameter of 8 mm was employed to investigate the separation
mechanism of the crude oil droplets from water. The cut-size
diameter eter of the crude oil was 10 - Ðçm in order to fit with the
operating range of the adopted hydrocylone model. Typical
parameters influencing the performance of hydrocyclone were varied
with the feed pressure in the range of 0.3 - 0.6 MPa and feed
concentration between 0.05 – 0.1 w%. In the simulation, the Finite
Element scheme was applied to investigate the particle-flow
interaction occurred in the crude oil system during the process. The
interaction of a single oil droplet at the size of 10 - Ðçm to the flow
field was observed. The feed concentration fell in the dilute flow
regime so the particle-particle interaction was ignored in the study.
The results exhibited the higher power requirement for the separation
of the elastic particulate system when compared with the rigid
particulate system.
Abstract: Nowadays pharmaceutical care departments located in
hospitals are amongst the important pillars of the healthcare system.
The aim of this study was to evaluate quality of hospital drugstores
affiliated with Kermanshah University of Medical Sciences.
In this cross-sectional study a validated questionnaire was used.
The questionnaire was filled in by the one of the researchers in all
seventeen hospital drugstores located in the teaching and nonteaching
hospitals affiliated with Kermanshah University of Medical
Sciences. The results shows that in observed hospitals,24% of
pharmacy environments, 25% of pharmacy store and storage
conditions, 49% of storage procedure, 25% of ordering drugs and
supplies, 73% of receiving supplies (proper procedure are fallowed
for receiving supplies), 35% of receiving supplies (prompt action
taken if deterioration of drugs received is suspected), 23.35% of
drugs delivery to patients and finally 0% of stock cards are used for
proper inventory control have full compliance with standards.
Abstract: Flash memory has become an important storage device
in many embedded systems because of its high performance, low
power consumption and shock resistance. Multi-level cell (MLC) is
developed as an effective solution for reducing the cost and increasing
the storage density in recent years. However, most of flash file system
cannot handle the error correction sufficiently. To correct more errors
for MLC, we implement Reed-Solomon (RS) code to YAFFS, what is
widely used for flash-based file system. RS code has longer computing
time but the correcting ability is much higher than that of Hamming
code.
Abstract: In this paper a computer system for electromagnetic
properties measurements is designed. The system employs Agilent
4294A precision impedance analyzer to measure the amplitude and
the phase of a signal applied over a tested biological tissue sample.
Measured by the developed computer system data could be used for
tissue characterization in wide frequency range from 40Hz to
110MHz. The computer system can interface with output devices
acquiring flexible testing process.
Abstract: Directive 2009/28/CE establishes, as obligatory objective, a share of renewable energies on energetic consumption of 20%, in European Union, in 2020 However, such European normative gives freedom to member states in the selection of the renewable promotion mechanism that allows them to obtain that objective. In this paper, we analyze the main characteristics of the promotion mechanisms of renewable energy used in the countries that shape the Electricity Iberian Market (Spain and Portugal) and the results in employment. The importance of these countries is given by the great increasing of the renewable energies which suppose a share higher than 30% of the overall generation in 2010. Therefore, this research paper can serve as the basis for the learning of other countries with regard to the main advantages that entail the use of a feed-in tariff system.
Abstract: There are several ways of improving the performance of a vapor compression refrigeration cycle. Use of an ejector as expansion device is one of the alternative ways. The present paper aims at evaluate the performance improvement of a vapor compression refrigeration cycle under a wide range of operating conditions. A numerical model is developed and a parametric study of important parameters such as condensation (30-50°C) and evaporation temperatures (-20-5°C), nozzle and diffuser efficiencies (0.75-0.95), subcooling and superheating degrees (0-15K) are investigated. The model verification gives a good agreement with the literature data. The simulation results revealed that condensation temperature has the highest effect (129%) on the performance improvement ratio while superheating has the lowest one (6.2%). Among ejector efficiencies, the diffuser efficiency has a significant effect on the COP of ejector expansion refrigeration cycle. The COP improvement percentage decreases from 10.9% to 4.6% as subcooling degrees increases by 15K.
Abstract: In this paper we propose a novel Run Time Interface
(RTI) technique to provide an efficient environment for MPI jobs on
the heterogeneous architecture of PARAM Padma. It suggests an
innovative, unified framework for the job management interface
system in parallel and distributed computing. This approach employs
proxy scheme. The implementation shows that the proposed RTI is
highly scalable and stable. Moreover RTI provides the storage access
for the MPI jobs in various operating system platforms and improve
the data access performance through high performance C-DAC
Parallel File System (C-PFS). The performance of the RTI is
evaluated by using the standard HPC benchmark suites and the
simulation results show that the proposed RTI gives good
performance on large scale supercomputing system.
Abstract: Ultrafast doped zinc oxide crystal promised us a good
opportunity to build new instruments for ICF fusion neutron
measurement. Two pulsed neutron detectors based on ZnO crystal
wafer have been conceptually designed, the superfast ZnO timing
detector and the scintillation recoil proton neutron detection system.
The structure of these detectors was presented, and some characters
were studied as well. The new detectors could be much faster than
existing systems, and would be more competent for ICF neutron
diagnostics.
Abstract: Efficient modulo 2n+1 adders are important for
several applications including residue number system, digital signal
processors and cryptography algorithms. In this paper we present a
novel modulo 2n+1 addition algorithm for a recently represented
number system. The proposed approach is introduced for the
reduction of the power dissipated. In a conventional modulo 2n+1
adder, all operands have (n+1)-bit length. To avoid using (n+1)-bit
circuits, the diminished-1 and carry save diminished-1 number
systems can be effectively used in applications. In the paper, we also
derive two new architectures for designing modulo 2n+1 adder, based
on n-bit ripple-carry adder. The first architecture is a faster design
whereas the second one uses less hardware. In the proposed method,
the special treatment required for zero operands in Diminished-1
number system is removed. In the fastest modulo 2n+1 adders in
normal binary system, there are 3-operand adders. This problem is
also resolved in this paper. The proposed architectures are compared
with some efficient adders based on ripple-carry adder and highspeed
adder. It is shown that the hardware overhead and power
consumption will be reduced. As well as power reduction, in some
cases, power-delay product will be also reduced.