Abstract: Plants are commonly known for its positive
correlation in reducing temperature. Since it can benefit buildings by
modifying the microclimate, it-s also believed capable of reducing
the internal temperature. Various experiments have been done in
Universiti Sains Malaysia, Penang to investigate the comparison in
thermal benefits between two rooms, one being a typical control
room (exposed wall) and the other a biofacade room (plant shaded
wall). The investigations were conducted during non-rainy season for
approximately a month. Climbing plant Psophocarpus
tetrogonobulus from legume species was selected as insulation for
the biofacade wall. Conclusions were made on whether the biofacade
can be used to tackle the energy efficiency, based on the parameters
taken into consideration.
Abstract: fifteen cultivars of Strawberries (Queen Eliza, Sequia,
Paros, Mcdonance, Selva, Chandler, Mrak, Ten beauty, Aliso, Pajero,
Kordestan, Camarosa, Blackmore, Gaviota and Fresno) were
investigated in 2011, under hydroponic system condition. Yield and
fruit Firmness was determinate. Chemical analyses of soluble solids
content (SSC), titratable acidity (TA), ascorbic acid (AA) and pH
were done. 4 cultivars (Aliso, Selva, Paros and Gaviota) yielded more
than 250 g/plant, while cultivar Black more, Fresno and Kordestan
produced less than 100g/plant. The amounts of fruit firmness
indicated that 'Camarosa' fruit was firmer than others cultivars.
Cultivar 'Fresno' had the highest pH (3.27). Ttitratable acidity varied
from 1.03g/l00g for cultivar 'Sequia' and 'Gaviota' to 1.48g/l00g for
cultivar 'Chandler'. Fresno, Kordestan, Aliso and Chandler showed
the highest soluble solid concentration. Ascorbic acid averaged for
most cultivars between 30.26 and 79.73 mg/100gf.w. Present results
showed that different cultivars of strawberry contain highly variable
in fruit quality.
Abstract: This work presents an approach for the measurement
of mutual inductance on near field inductive coupling. The mutual
inductance between inductive circuits allows the simulation of energy
transfer from reader to tag, that can be used in RFID and powerless
implantable devices. It also allows one to predict the maximum
voltage in the tag of the radio-frequency system.
Abstract: The growth of the aquaculture industry has been
associated with negative environmental impacts through the
discharge of raw effluents into the adjacent receiving water bodies.
Macrophytes from natural saline lakes, which have adaptability to the
high salinity, can be suitable for saline effluent treatment. Eight
emergent species from natural saline area were planted in an
experimental gravel bed hydroponic mesocosm (GBH) which was
treated with effluent water from an intensive fish farm using
geothermal water. In order to examine the applicability of the
halophytes in treatment processes, we tested the relative efficacy of
total nitrogen (TN), total phosphorus (TP), potassium (K), sodium
(Na), magnesium (Mg) and calcium (Ca) removal for the saline
wastewater treatment. Four of the eight species, which were
Phragmites australis, Typha angustifolia, Glyceria maxima, Scirpus
lacustris spp. tabernaemontani could survive and contribute the
experimental treatment.
Abstract: This work aims to investigate a potential of
microalgae for utilizing industrial wastewater as a cheap nutrient for
their growth and oil accumulation. Wastewater was collected from
the effluent ponds of agro-industrial factories (cassava and ethanol
production plants). Only 2 microalgal strains were isolated and
identified as Scenedesmus quadricauda and Chlorella sp.. However,
only S. quadricauda was selected to cultivate in various wastewater
concentrations (10%, 20%, 40%, 60%, 80% and 100%). The highest
biomass obtained at 6.6×106 and 6.27×106 cells/ml when 60%
wastewater was used in flask and photo-bioreactor. The cultures gave
the highest lipid content at 18.58 % and 42.86% in cases of S.
quadricauda and S. obliquus. In addition, under salt stress (1.0 M
NaCl), S. obliquus demonstrated the highest lipid content at 50%
which was much more than the case of no NaCl adding. However, the
concentration of NaCl does not affect on lipid accumulation in case
of S. quadricauda.
Abstract: The main features of NPP-2006/MIR-1200 design are
described. Estimation of individual doses for population under
normal operation and accident conditions is performed for
Leningradskaya NPP – 2 as an example. The radiation effect on
population and environment doesn-t exceed the established
normative limit and is as low as reasonably achievable. NPP-
2006/MIR-1200 design meets all Russian and international
requirements for power units under construction.
Abstract: Programmable logic controllers are the main controllers in the today's industries; they are used for several applications in industrial control systems and there are lots of examples exist from the PLC applications in industries especially in big companies and plants such as refineries, power plants, petrochemical companies, steel companies, and food and production companies. In the PLCs there are some functions in the function library in software that can be used in PLC programs as basic program elements. The aim of this project are introducing and implementing a new function block of a neural network to the function library of PLC. This block can be applied for some control applications or nonlinear functions calculations after it has been trained for these applications. The implemented neural network is a Perceptron neural network with three layers, three input nodes and one output node. The block can be used in manual or automatic mode. In this paper the structure of the implemented function block, the parameters and the training method of the network are presented by considering the especial method of PLC programming and its complexities. Finally the application of the new block is compared with a classic simulated block and the results are presented.
Abstract: In the LFC problem, the interconnections among some areas are the input of disturbances, and therefore, it is important to suppress the disturbances by the coordination of governor systems. In contrast, tie-line power flow control by TCPS located between two areas makes it possible to stabilize the system frequency oscillations positively through interconnection, which is also expected to provide a new ancillary service for the further power systems. Thus, a control strategy using controlling the phase angle of TCPS is proposed for provide active control facility of system frequency in this paper. Also, the optimum adjustment of PID controller's parameters in a robust way under bilateral contracted scenario following the large step load demands and disturbances with and without TCPS are investigated by Particle Swarm Optimization (PSO), that has a strong ability to find the most optimistic results. This newly developed control strategy combines the advantage of PSO and TCPS and has simple stricture that is easy to implement and tune. To demonstrate the effectiveness of the proposed control strategy a three-area restructured power system is considered as a test system under different operating conditions and system nonlinearities. Analysis reveals that the TCPS is quite capable of suppressing the frequency and tie-line power oscillations effectively as compared to that obtained without TCPS for a wide range of plant parameter changes, area load demands and disturbances even in the presence of system nonlinearities.
Abstract: Theory of Constraints has been emerging as an
important tool for optimization of manufacturing/service systems.
Goldratt in his first book “ The Goal " gave the introduction on
Theory of Constraints and its applications in a factory scenario. A
large number of production managers around the globe read this book
but only a few could implement it in their plants because the book did
not explain the steps to implement TOC in the factory. To overcome
these limitations, Goldratt wrote this book to explain TOC, DBR and
the method to implement it. In this paper, an attempt has been made
to summarize the salient features of TOC and DBR listed in the book
and the correct approach to implement TOC in a factory setting. The
simulator available along with the book was actually used by the
authors and the claim of Goldratt regarding the use of DBR and
Buffer management to ease the work of production managers was
tested and was found to be correct.
Abstract: Rotational Smart Lighting Control System can supply
the quantity of lighting which is required to run plants by rotating few
LED and Fluorescent instead of that are used in the existing plant
factories.The initial installation of the existing plants factory is
expensive, so in order to solve the problem with smart lighting control
system was developed.
The beam required intensity for the growth of crops, Photosynthetic
Photon Flux Density(PPFD)is calculated; and the number of LED, are
installed on the blades, set; using the Lighting Simulation
Program.Relux, it is able to confirm that the difference of the beam
intensity between the center and the outer of lighting system when the
lighting device is rotating.
Abstract: This study was conducted to investigate the efficacy
of five herbicides on narrow leaved weeds and growth and yield of
wheat. An experiment was conducted at Agronomic Research
Farm, University of Agriculture Faisalabad. The experiment was
laid out in randomized complete block designee (RCBD) with three
replications. Treatments studied were clodinafop (Topic-15 WG) at
37 g a.i. ha-1, clodinafop (Topaz-15 WG) at 45 g a.i. ha-1,
fenoxaprop-p-ethyl (Puma Super-75 EW) at 45 g a.i. ha-1,
fenoxaprop-p-ethyl (Gramicide-6.9 EW) at 85 g a.i. ha-1,
fenoxaprop-p-ethyl (Chinlima-6.9 EW) at 85 g a.i. ha-1 and weedy
check. Plots treated with fenoxaprop-p-ethyl (Puma Super-75 EW)
at 45 g a.i. ha-1 produced relatively less weed biomass, more plant
height, number of spike bearing tillers, number of grains per spike,
1000-grain weight and grain yield (4.20 t ha-1).
Abstract: This paper provides an exergy analysis of the multistage refrigeration cycle used for C2+ recovery plant. The behavior of an industrial refrigeration cycle with refrigerant propane has been investigated by the exergy method. A computational model based on the exergy analysis is presented for the investigation of the effects of the valves on the exergy losses, the second law of efficiency, and the coefficient of performance (COP) of a vapor compression refrigeration cycle. The equations of exergy destruction and exergetic efficiency for the main cycle components such as evaporators, condensers, compressors, and expansion valves are developed. The relations for the total exergy destruction in the cycle and the cycle exergetic efficiency are obtained. An ethane recovery unit with its refrigeration cycle has been simulated to prepare the exergy analysis. Using a typical actual work input value; the exergetic efficiency of the refrigeration cycle is determined to be 39.90% indicating a great potential for improvements. The simulation results reveal that the exergetic efficiencies of the heat exchanger and expansion sections get the lowest rank among the other compartments of refrigeration cycle. Refrigeration calculations have been carried out through the analysis of T–S and P–H diagrams where coefficient of performance (COP) was obtained as 1.85. The novelty of this article includes the effect and sensitivity analysis of molar flow, pressure drops and temperature on the exergy efficiency and coefficient of performance of the cycle.
Abstract: The peel of dragon fruit is a byproduct left over after consuming. Normally, the use of plants as antioxidant source must be dried before further process. Therefore, the aim of this study is interesting to dry the peel by heat pump dryer (45 ºC) and fluidized bed dryer (110 º C) compared with the sun drying method. The sample with initial moisture content of about 85-91% wet basis was dried down to about 10% wet basis where it took 620 and 25 min for heat pump dryer and fluidized bed dryer, respectively. However, the sun drying took about 900 min to dry the peel. After that, sample was evaluated antioxidant activity, -carotene and betalains contents. The results found that the antioxidant activity and betalains contents of dried peel obtained from heat pump and fluidized bed dryings were significantly higher than that sun drying (p 0.05). Moreover, the drying by heat pump provided the highest -carotene content.
Abstract: In this paper, a TSK-type Neuro-fuzzy Inference
System that combines the features of fuzzy sets and neural networks
has been applied for the identification of MIMO systems. The procedure of adapting parameters in TSK model employs a Shuffled
Frog Leaping Algorithm (SFLA) which is inspired from the memetic evolution of a group of frogs when seeking for food. To demonstrate
the accuracy and effectiveness of the proposed controller, two nonlinear systems have been considered as the MIMO plant, and results have been compared with other learning methods based on
Particle Swarm Optimization algorithm (PSO) and Genetic
Algorithm (GA).
Abstract: The extract of milk thistle contains a mix of flavonolignans termed silymarine.. In order to analysis influence of growth regulators, genotype, explant and subculture on the accumulation of flavonolignans, a study was carried out by using two genotype (Budakalszi and Noor abad moghan cultivars), cotyledon and hypocotyle explants, solid media of MS supplemented by different combinations of two growth regulators; Kinetin (0.1, 1 mg/l) and 2,4-D (1, 2 mg/l). Seeds of the plant were germinated in MS media whitout growth regulators in growth chamber at 26°C and darkness condition. In order to callus induction, the culture media was supplemented whit different concentrations of 2,4-D and kinetin. Calli obtained from explants were sub-cultured four times into the fresh media of the first experiment. flavonoides was extracted from calli in four subcultures. The flavonoid components were determined by high- performance liquid choromatography (HPLC) and separated into Taxifolin, Silydianin+Silychristin, Silybin A+B and Isosilybin A+B. Results showed that with increasing callus age, increased accumulation of silybin A+B, but reduced Isosilybin A+B content. Highest accumulation of Taxifolin was observed at first calli. Calli produced from cotyledon explant of Budakalszi cultivar were superior for Silybin A+B, where calli from hypocotyl explant produced higher amount of Taxifolin and Silydianin+Silychristin. The best cultivar for Silymarin production in this study was Budakalszi cultivar. High amount of SBN A+B and TXF were obtained from hypocotil explant.
Abstract: There was a high rate of corrosion in Pyrolysis
Gasoline Hydrogenation (PGH) unit of Arak Petrochemical Company
(ARPC), and it caused some operational problem in this plant. A
commercial chemical had been used as anti-corrosion in the
depentanizer column overhead in order to control the corrosion rate.
Injection of commercial corrosion inhibitor caused some
operational problems such as fouling in some heat exchangers. It was
proposed to replace this commercial material with another more
effective trouble free, and well-known additive by R&D and
operation specialists.
At first, the system was simulated by commercial simulation
software in electrolytic system to specify low pH points inside the
plant. After a very comprehensive study of the situation and technical
investigations ,ammonia / monoethanol amine solution was proposed
as neutralizer or corrosion inhibitor to be injected in a suitable point
of the plant. For this purpose, the depentanizer column and its
accessories system was simulated again in case of this solution
injection.
According to the simulation results, injection of new anticorrosion
substance has no any side effect on C5 cut product and
operating conditions of the column. The corrosion rate will be
cotrolled, if the pH remains at the range of 6.5 to 8 . Aactual plant
test run was also carried out by injection of ammonia / monoethanol
amine solution at the rate of 0.6 Kg/hr and the results of iron content
of water samples and corrosion test coupons confirmed the
simulation results.
Now, ammonia / monoethanol amine solution is injected to a
suitable pint inside the plant and corrosion rate has decreased
significantly.
Abstract: Accurate and comprehensive thermodynamic properties of pure and mixture of refrigerants are in demand by both producers and users of these materials. Information about thermodynamic properties is important initially to qualify potential candidates for working fluids in refrigeration machinery. From practical point of view, Refrigerants and refrigerant mixtures are widely used as working fluids in many industrial applications, such as refrigerators, heat pumps, and power plants The present work is devoted to evaluating seven cubic equations of state (EOS) in predicting gas and liquid phase volumetric properties of nine ozone-safe refrigerants both in super and sub-critical regions. The evaluations, in sub-critical region, show that TWU and PR EOS are capable of predicting PVT properties of refrigerants R32 within 2%, R22, R134a, R152a and R143a within 1% and R123, R124, R125, TWU and PR EOS's, from literature data are 0.5% for R22, R32, R152a, R143a, and R125, 1% for R123, R134a, and R141b, and 2% for R124. Moreover, SRK EOS predicts PVT properties of R22, R125, and R123 to within aforementioned errors. The remaining EOS's predicts volumetric properties of this class of fluids with higher errors than those above mentioned which are at most 8%.In general, the results are in favor of the preference of TWU and PR EOS over other remaining EOS's in predicting densities of all mentioned refrigerants in both super and sub critical regions. Typically, this refrigerant is known to offer advantages such as ozone depleting potential equal to zero, Global warming potential equal to 140, and no toxic.
Abstract: In production of medicinal plants, seed germination is
very important problem. The treated seeds (control, hydro priming
and ZnSO4) of Cumin (Cuminum cyminum L.) were evaluated at
germination and seedling growth for tolerance to salt (NaCl and
Na2SO4) conditions at the same water potentials of 0.0, -0.3, -0.6, -
0.9 and -1.2MPa. Electrical conductivity (EC) values of the NaCl
solutions were 0.0, 6.5, 12.7, 18.4 and 23.5 dSm-1, respectively. The
objective of the study was to determine factors responsible for
germination and early seedling growth due to salt toxicity or osmotic
effect and to optimize the best priming treatment for these stress
conditions. Results revealed that germination delayed in both
solutions, having variable germination with different priming
treatments. Germination, shoot and weight, root and shoot length
were higher but mean germination time and abnormal germination
percentage were lower in NaCl than Na2SO4 at the same water
potential. The root / shoot weight and R/S length increased with
increase in osmotic potential in both NaCl and Na2SO4 solutions.
NaCl had less inhibitor effect on seedling growth than the
germination. It was concluded that inhibition of germination at the
same water potential of NaCl and Na2SO4 resulted from salt toxicity
rather than osmotic effect. Hydro priming increased germination and
seedling growth under salt stress. This protocol has practical
importance and could be recommended to farmers to achieve higher
germination and uniform emergence under field conditions.
Abstract: Pentachlorophenol (PCP) is a polychlorinated
aromatic compound that is widespread in industrial effluents and is
considered to be a serious pollutant. Among the variety of industrial
effluents encountered, effluents from tanning industry are very
important and have a serious pollution potential. PCP is also formed
unintentionally in effluents of paper and pulp industries. It is highly
persistent in soils and is lethal to a wide variety of beneficial
microorganisms and insects, human beings and animals. The natural
processes that breakdown toxic chemicals in the environment have
become the focus of much attention to develop safe and environmentfriendly
deactivation technologies. Microbes and plants are among
the most important biological agents that remove and degrade waste
materials to enable their recycling in the environment. The present
investigation was carried out with the aim of developing a microbial
system for bioremediation of PCP polluted soils. A number of plant
species were evaluated for their ability to tolerate different
concentrations of pentachlorophenol (PCP) in the soil. The
experiment was conducted for 30 days under pot culture conditions.
The toxic effect of PCP on plants was studied by monitoring seed
germination, plant growth and biomass. As the concentration of PCP
was increased to 50 ppm, the inhibition of seed germination, plant
growth and biomass was also increased. Although PCP had a
negative effect on all plant species tested, maize and groundnut
showed the maximum tolerance to PCP. Other tolerating crops
included wheat, safflower, sunflower, and soybean. From the
rhizosphere soil of the tolerant seedlings, as many as twenty seven
PCP tolerant bacteria were isolated. From soybean, 8; sunflower, 3;
safflower 8; maize 2; groundnut and wheat, 3 each isolates were
made. They were screened for their PCP degradation potentials.
HPLC analyses of PCP degradation revealed that the isolate MAZ-2
degraded PCP completely. The isolate MAZ-1 was the next best
isolate with 90 per cent PCP degradation. These strains hold promise
to be used in the bioremediation of PCP polluted soils.
Abstract: The PRAF family of proteins is a plant specific family of proteins with distinct domain architecture and various unique sequence/structure traits. We have carried out an extensive search of the Arabidopsis genome using an automated pipeline and manual methods to verify previously known and identify unknown instances of PRAF proteins, characterize their sequence and build 3D structures of their individual domains. Integrating the sequence, structure and whatever little known experimental details for each of these proteins and their domains, we present a comprehensive characterization of the different domains in these proteins and their variant properties.