Abstract: Recently, permeable breakwaters have been suggested to overcome the disadvantages of fully protection breakwaters. These protection structures have minor impacts on the coastal environment and neighboring beaches where they provide a more economical protection from waves and currents. For regular waves, a numerical model is used (FLOW-3D, VOF) to investigate the hydraulic performance of a permeable breakwater. The model of permeable breakwater consists of a pair of identical vertical slotted walls with an impermeable upper and lower part, where the draft is a decimal multiple of the total depth. The middle part is permeable with a porosity of 50%. The second barrier is located at distant of 0.5 and 1.5 of the water depth from the first one. The numerical model is validated by comparisons with previous laboratory data and semi-analytical results of the same model. A good agreement between the numerical results and both laboratory data and semi-analytical results has been shown and the results indicate the applicability of the numerical model to reproduce most of the important features of the interaction. Through the numerical investigation, the friction factor of the model is carefully discussed.
Abstract: This paper presents a comparison between Spectrum-
Sliced Wavelength Division Multiplexing (SS-WDM) and Spectrum
Amplitude Coding Optical Code Division Multiple Access (SAC
Optical CDMA) systems for different light sources. The performance
of the system is shown in the simulated results of the bit error rate
(BER) and the eye diagram of both systems. The comparison results
indicate that the Multiple Access Interference (MAI) effects have a
significant impact on SS-WDM over SAC Optical CDMA systems.
Finally, in terms of spectral efficiency at constant BER of 10-12, SSWDM
offers higher spectral efficiency than optical CDMA since no
bandwidth expansion in needed.
Abstract: Antifungal activities of ether and methanolic extracts of volatiles oils of Nigella Sativa seeds were tested against pathogenic bacterias and fungies strains.The volatile oil were found to have significant antifungal and antibacterial activities compare to tetracycline, cefuroxime and ciprofloxacin positive controls.The ether and methanolic esxtracts were compared to each other for antifungal and antibacterial activities and ether extracts showed stonger activity than methanolic one.
Abstract: Statistical analysis of electrophysiological recordings
obtained under, e.g. tactile, stimulation frequently suggests participation
in the network dynamics of experimentally unobserved “hidden"
neurons. Such interneurons making synapses to experimentally
recorded neurons may strongly alter their dynamical responses to
the stimuli. We propose a mathematical method that formalizes this
possibility and provides an algorithm for inferring on the presence
and dynamics of hidden neurons based on fitting of the experimental
data to spike trains generated by the network model. The model
makes use of Integrate and Fire neurons “chemically" coupled
through exponentially decaying synaptic currents. We test the method
on simulated data and also provide an example of its application to
the experimental recording from the Dorsal Column Nuclei neurons
of the rat under tactile stimulation of a hind limb.
Abstract: In order to evaluation the effects of natural, biological
and chemical fertilizers on grain yield and chickpea quality, field
experiments were carried out in 2007 and 2008 growing seasons. In
this research the effects of different organic, chemical and biological
fertilizers were investigated on grain yield and quality of chickpea.
Experimental units were arranged in split-split plots based on
randomized complete blocks with three replications. The highest
amounts of yield and yield components were obtained in G1×N5
interaction. Significant increasing of N, P, K, Fe and Mg content in
leaves and grains emphasized on superiority of mentioned treatment
because each one of these nutrients has an approved role in
chlorophyll synthesis and photosynthesis ability of the crop. The
combined application of compost, farmyard manure and chemical
phosphorus (N5) had the best grain quality due to high protein, starch
and total sugar contents, low crude fiber and reduced cooking time.
Abstract: In this paper, Wavelet based ANFIS for finding inter
turn fault of generator is proposed. The detector uniquely responds to
the winding inter turn fault with remarkably high sensitivity.
Discrimination of different percentage of winding affected by inter
turn fault is provided via ANFIS having an Eight dimensional input
vector. This input vector is obtained from features extracted from
DWT of inter turn faulty current leaving the generator phase
winding. Training data for ANFIS are generated via a simulation of
generator with inter turn fault using MATLAB. The proposed
algorithm using ANFIS is giving satisfied performance than ANN
with selected statistical data of decomposed levels of faulty current.
Abstract: Generally, in order to create 3D sound using binaural
systems, we use head related transfer functions (HRTF) including the
information of sounds which is arrived to our ears. But it can decline
some three-dimensional effects in the area of a cone of confusion
between front and back directions, because of the characteristics of
HRTF.
In this paper, we propose a new method to use psychoacoustics
theory that reduces the confusion of sound image localization. In the
method, HRTF spectrum characteristic is enhanced by using the
energy ratio of the bark band. Informal listening tests show that the
proposed method improves the front-back sound localization
characteristics much better than the conventional methods
Abstract: Chatter vibration has been a troublesome problem
for a machine tool toward the high precision and high speed machining.
Essentially, the machining performance is determined by the dynamic
characteristics of the machine tool structure and dynamics of cutting
process, which can further be identified in terms of the stability lobe
diagram. Therefore, realization on the machine tool dynamic behavior
can help to enhance the cutting stability. To assess the dynamic
characteristics and machining stability of a vertical milling system
under the influence of a linear guide, this study developed a finite
element model integrated the modeling of linear components with the
implementation of contact stiffness at the rolling interface. Both the
finite element simulations and experimental measurements reveal that
the linear guide with different preload greatly affects the vibration
behavior and milling stability of the vertical column spindle head
system, which also clearly indicate that the predictions of the
machining stability agree well with the cutting tests. It is believed that
the proposed model can be successfully applied to evaluate the
dynamics performance of machine tool systems of various
configurations.
Abstract: The African Diaspora in Singapore (and larger Asia)
is a topic that has received little scholarly attention and research. This
exploratory study will analyze the changing identity of Africans
throughout the process of cultural adaptation in Singapore. For the
focus of this study, “black Africans" will be defined as any black
Africans from sub-Saharan Africa who have lived in Singapore for at
least six months. The dialectic relationship between Singaporean
conceptions of black African identity and African self-consciousness
will be analyzed from the perspective of black Africans so as to
evaluate the impact of intercultural discourse on the evolution of the
African identity in Singapore.
Abstract: In recent years, response surface methodology (RSM) has
brought many attentions of many quality engineers in different
industries. Most of the published literature on robust design
methodology is basically concerned with optimization of a single
response or quality characteristic which is often most critical to
consumers. For most products, however, quality is multidimensional,
so it is common to observe multiple responses in an experimental
situation. Through this paper interested person will be familiarize
with this methodology via surveying of the most cited technical
papers.
It is believed that the proposed procedure in this study can resolve
a complex parameter design problem with more than two responses.
It can be applied to those areas where there are large data sets and a
number of responses are to be optimized simultaneously. In addition,
the proposed procedure is relatively simple and can be implemented
easily by using ready-made standard statistical packages.
Abstract: This paper introduces and proves new concept of salt
dissolving in water as very tiny solid sodium chloride particles of
nanovolumes, from this point of view salt water can be desalinated by
collision with special surface characterized by smoothness upon nano
level, high rigidity, high hardness under appropriate conditions of
water launching in the form of thin laminar flow under suitable speed
and angle of incidence to get desalinated water.
Abstract: This paper presents a method for obtaining the
desired reference current for Voltage Source Converter (VSC) of the Shunt Active Power Filter (SAPF) using Synchronous Reference Frame Theory. The method relies on the performance of the Proportional-Integral (PI) controller for
obtaining the best control performance of the SAPF. To
improve the performance of the PI controller, the feedback
path to the integral term is introduced to compensate the
winding up phenomenon due to integrator. Using Reference
Frame Transformation, reference signals are transformed from
a - b - c stationery frame to 0 - d - q rotating frame.
Using the PI controller, the reference signals in the 0 - d - q rotating frame are controlled to get the desired reference signals for the Pulse Width Modulation. The synchronizer, the Phase Locked Loop (PLL) with PI filter is used for
synchronization, with much emphasis on minimizing delays. The system performance is examined with Shunt Active Power Filter simulation model.
Abstract: Under the difficult access to finance of SMEs, they expect that its relationship with the banks shall constitute a real help to access appropriate financing, at reasonable costs and requirements, given the possibility of mutually beneficial and long lasting relation. The literature, but also the research we have carried on, is centered on such determinants as concentration and the length of the relationship, but at the same time, there is little certainty that banks are responding positively to them. Furthermore, although the trust is considered as being a fundamental element of bank relationship – see the case house bank – SMEs find that the banks finance them looking rather on collaterals and covenants than to trust. Moreover, a positive behavior, such as prompt or advance repayments of loans, doesn-t generate any positive feedback from the banks side. All these show a deep un-satisfaction of the SMEs concerning their relationship banking.
Abstract: By systematically applying different engineering
methods, difficult financial problems become approachable. Using a
combination of theory and techniques such as wavelet transform,
time series data mining, Markov chain based discrete stochastic
optimization, and evolutionary algorithms, this work formulated a
strategy to characterize and forecast non-linear time series. It
attempted to extract typical features from the volatility data sets of
S&P100 and S&P500 indices that include abrupt drops, jumps and
other non-linearity. As a result, accuracy of forecasting has reached
an average of over 75% surpassing any other publicly available
results on the forecast of any financial index.
Abstract: A new tool path planning method for 5-axis flank
milling of a globoidal indexing cam is developed in this paper. The
globoidal indexing cam is a practical transmission mechanism due
to its high transmission speed, accuracy and dynamic performance.
Machining the cam profile is a complex and precise task. The profile
surface of the globoidal cam is generated by the conjugate contact
motion of the roller. The generated complex profile surface is usually
machined by 5-axis point-milling method. The point-milling method
is time-consuming compared with flank milling. The tool path for
5-axis flank milling of globoidal cam is developed to improve the
cutting efficiency. The flank milling tool path is globally optimized
according to the minimum zone criterion, and high accuracy is
guaranteed. The computational example and cutting simulation finally
validate the developed method.
Abstract: The effect of flakes from biologically activated hullless barley grain and malt extract on microbiological safety of yoghurt was studied. Pasteurized milk, freeze-dried yoghurt culture YF-L811 (Chr. Hansen, Denmark), flakes from biologically activated hull-less barley grain (Latvia) and malt extract (Ilgezeem, Latvia) were used for experiments. Yoghurt samples with flakes from biologically activated hull-less barley grain and malt extract were analyzed for total plate count of mesophylic aerobic and facultative anaerobic microorganisms, as well yeasts and moulds population during shelflife. Results showed that the changes of pH and titratable acidity affected the concentration of added malt extract. The lowest pH and the highest titratable acidity were determined in samples YFBG5% ME4% and YFBG5% ME6% on the 14th day. The total plate count decreased in all yoghurt samples except sample YFBG5% ME6%, where was determined the increase of microorganisms from 7th till 14th day. The adding of flakes from biologically activated hull-less barley grain in yoghurt samples caused the higher initial content of yeasts and moulds comparing with control. The growth of yeasts and moulds during shelf-life provided the added malt extract in yoghurt samples. Yoghurt enriched with flakes from biologically activated hull-less barley grain and malt extract from a microbiological perspective is safe product.
Abstract: We present an integration approach of a CMOS biosensor into a polymer based microfluidic environment suitable for mass production. It consists of a wafer-level-package for the silicon die and laser bonding process promoted by an intermediate hot melt foil to attach the sensor package to the microfluidic chip, without the need for dispensing of glues or underfiller. A very good condition of the sensing area was obtained after introducing a protection layer during packaging. A microfluidic flow cell was fabricated and shown to withstand pressures up to Δp = 780 kPa without leakage. The employed biosensors were electrically characterized in a dry environment.
Abstract: Cabbage seedlings grown in vitro were exposed to
excess levels of heavy metals, including Cd, Mo, and Zn. High metal
levels affected plant growth at cotyledonary stage. Seedlings under
Cd, Mo, and Zn treatments could not produce root hairs and true
leaves. Under stress conditions, seedlings accumulated a higher
amount of anthocyanins in their cotyledons than those in the control.
The pigments isolated from Cd and Zn stressed seedling cotyledons
appeared as pink, while under Mo stress, was dark pink or purple.
Moreover, excess Mo stress increased antioxidant enzyme activities
of APX, CAT, SOD. These results suggest that, under excess Mo
stress, the induced antioxidant enzyme activity of cabbage seedlings
may function as a protective mechanism to shield the plants from
toxicity and exacerbated growth.
Abstract: Overloading is a technique to accommodate more
number of users than the spreading factor N. This is a bandwidth
efficient scheme to increase the number users in a fixed bandwidth.
One of the efficient schemes to overload a CDMA system is to use
two sets of orthogonal signal waveforms (O/O). The first set is
assigned to the N users and the second set is assigned to the
additional M users. An iterative interference cancellation technique is
used to cancel interference between the two sets of users. In this
paper, the performance of an overloading scheme in which the first N
users are assigned Walsh-Hadamard orthogonal codes and extra users
are assigned the same WH codes but overlaid by a fixed (quasi) bent
sequence [11] is evaluated. This particular scheme is called Quasi-
Orthogonal Sequence (QOS) O/O scheme, which is a part of
cdma2000 standard [12] to provide overloading in the downlink
using single user detector. QOS scheme are balance O/O scheme,
where the correlation between any set-1 and set-2 users are
equalized. The allowable overload of this scheme is investigated in
the uplink on an AWGN and Rayleigh fading channels, so that the
uncoded performance with iterative multistage interference
cancellation detector remains close to the single user bound. It is
shown that this scheme provides 19% and 11% overloading with
SDIC technique for N= 16 and 64 respectively, with an SNR
degradation of less than 0.35 dB as compared to single user bound at
a BER of 0.00001. But on a Rayleigh fading channel, the channel
overloading is 45% (29 extra users) at a BER of 0.0005, with an SNR
degradation of about 1 dB as compared to single user performance
for N=64. This is a significant amount of channel overloading on a
Rayleigh fading channel.
Abstract: In accordance with environmental impacts contended in Kyoto Protocol, the study aims to explore the different administrative and non-administrative measurements that industrial countries, such as America, German, Japan, Korea, Holland and British take to face with the increasing Global Warming phenomena. By large, these measurements consist of versatile dimensions, including of education and advocating, economical instruments, research developments and instances, restricted instruments, voluntary contacts, exchangeable permit for carbon-release and public investments. The results of discussion for the study are as follows: both economical impacts as well as reformations for nations that are affected via Kyoto Protocol, and human testifying for variables of global surroundings in the age of Kyoto Protocol.