Abstract: This work presents a methodology for the selection
and design of propeller oriented to the experimental verification of
theoretical results. The problem of propeller selection and design
usually present itself in the following manner: a certain air volume
and static pressure are required for a certain system. Once the
necessity of fan design on a theoretical basis has been recognized, it
is possible to determinate the dimensions for a fan unit so that it will
perform in accordance with a certain set of specifications. The same
procedures in this work then can be applied in other propeller
selection.
Abstract: Any use of energy in industrial productive activities is combined with various environment impacts. Withintransportation,
this fact was not only found among land transport, railways and maritime transport, but also in the air transport industry. An effective climate protection requires strategies and measures for reducing all
greenhouses gas emissions, in particular carbon dioxide, and must
take into account the economic, ecologic and social aspects. It seem simperative now to develop and manufacture environmentally
friendly products and systems, to reduce consumption and use less
resource, and to save energy and power. Today-sproducts could
better serve these requirements taking into account the integration of
a power management system into the electrical power system.This
paper gives an overview of an approach ofpower management with
load prioritization in modernaircraft. Load dimensioning and load
management strategies on current civil aircraft will be presented and
used as a basis for the proposed approach.
Abstract: Vortices can develop in intakes of turbojet and turbo
fan aero engines during high power operation in the vicinity of solid
surfaces. These vortices can cause catastrophic damage to the engine.
The factors determining the formation of the vortex include both
geometric dimensions as well as flow parameters. It was shown that
the threshold at which the vortex forms or disappears is also
dependent on the initial flow condition (i.e. whether a vortex forms
after stabilised non vortex flow or vice-versa). A computational fluid
dynamics study was conducted to determine the difference in
thresholds between the two conditions. This is the first reported
numerical investigation of the “memory effect". The numerical
results reproduce the phenomenon reported in previous experimental
studies and additional factors, which had not been previously studied,
were investigated. They are the rate at which ambient velocity
changes and the initial value of ambient velocity. The former was
found to cause a shift in the threshold but not the later. It was also
found that the varying condition thresholds are not symmetrical about
the neutral threshold. The vortex to no vortex threshold lie slightly
further away from the neutral threshold compared to the no vortex to
vortex threshold. The results suggests that experimental investigation
of vortex formation threshold performed either in vortex to no vortex
conditions, or vice versa, solely may introduce mis-predictions
greater than 10%.
Abstract: In this paper the principle, basic torque theory and design optimisation of a six-phase reluctance dc machine are considered. A trapezoidal phase current waveform for the machine drive is proposed and evaluated to minimise ripple torque. Low cost normal laminated salient-pole rotors with and without slits and chamfered poles are investigated. The six-phase machine is optimised in multi-dimensions by linking the finite-element analysis method directly with an optimisation algorithm; the objective function is to maximise the torque per copper losses of the machine. The armature reaction effect is investigated in detail and found to be severe. The measured and calculated torque performances of a 35 kW optimum designed six-phase reluctance dc machine drive are presented.
Abstract: This paper presents the use of three-dimensional finite
elements coupled with infinite elements to investigate the ground
vibrations at the surface in terms of the peak particle velocity (PPV)
due to construction of the first bore of the Dublin Port Tunnel. This
situation is analysed using a commercially available general-purpose
finite element package ABAQUS. A series of parametric studies is
carried out to examine the sensitivity of the predicted vibrations to
variations in the various input parameters required by finite element
method, including the stiffness and the damping of ground. The
results of this study show that stiffness has a more significant effect
on the PPV rather than the damping of the ground.
Abstract: In Content-Based Image Retrieval systems it is
important to use an efficient indexing technique in order to perform
and accelerate the search in huge databases. The used indexing
technique should also support the high dimensions of image features.
In this paper we present the hierarchical index NOHIS-tree (Non
Overlapping Hierarchical Index Structure) when we scale up to very
large databases. We also present a study of the influence of clustering
on search time. The performance test results show that NOHIS-tree
performs better than SR-tree. Tests also show that NOHIS-tree keeps
its performances in high dimensional spaces. We include the
performance test that try to determine the number of clusters in
NOHIS-tree to have the best search time.
Abstract: Time-Cost Optimization "TCO" is one of the greatest challenges in construction project planning and control, since the optimization of either time or cost, would usually be at the expense of the other. Since there is a hidden trade-off relationship between project and cost, it might be difficult to predict whether the total cost would increase or decrease as a result of the schedule compression. Recently third dimension in trade-off analysis is taken into consideration that is quality of the projects. Few of the existing algorithms are applied in a case of construction project with threedimensional trade-off analysis, Time-Cost-Quality relationships. The objective of this paper is to presents the development of a practical software system; that named Automatic Multi-objective Typical Construction Resource Optimization System "AMTCROS". This system incorporates the basic concepts of Line Of Balance "LOB" and Critical Path Method "CPM" in a multi-objective Genetic Algorithms "GAs" model. The main objective of this system is to provide a practical support for typical construction planners who need to optimize resource utilization in order to minimize project cost and duration while maximizing its quality simultaneously. The application of these research developments in planning the typical construction projects holds a strong promise to: 1) Increase the efficiency of resource use in typical construction projects; 2) Reduce construction duration period; 3) Minimize construction cost (direct cost plus indirect cost); and 4) Improve the quality of newly construction projects. A general description of the proposed software for the Time-Cost-Quality Trade-Off "TCQTO" is presented. The main inputs and outputs of the proposed software are outlined. The main subroutines and the inference engine of this software are detailed. The complexity analysis of the software is discussed. In addition, the verification, and complexity of the proposed software are proved and tested using a real case study.
Abstract: Non-isothermal stagnation-point flow with consideration of thermal radiation is studied numerically. A set of partial differential equations that governing the fluid flow and energy is converted into a set of ordinary differential equations which is solved by Runge-Kutta method with shooting algorithm. Dimensionless wall temperature gradient and temperature boundary layer thickness for different combinaton of values of Prandtl number Pr and radiation parameter NR are presented graphically. Analyses of results show that the presence of thermal radiation in the stagnation-point flow is to increase the temperature boundary layer thickness and decrease the dimensionless wall temperature gradient.
Abstract: In this paper, an magnetorheological (MR) mount with
fuzzy sliding mode controller (FSMC) is studied for vibration
suppression when the system is subject to base excitations. In recent
years, magnetorheological fluids are becoming a popular material in
the field of the semi-active control. However, the dynamic equation of
an MR mount is highly nonlinear and it is difficult to identify. FSMC
provides a simple method to achieve vibration attenuation of the
nonlinear system with uncertain disturbances. This method is capable
of handling the chattering problem of sliding mode control effectively
and the fuzzy control rules are obtained by using the Lyapunov
stability theory. The numerical simulations using one-dimension and
two-dimension FSMC show effectiveness of the proposed controller
for vibration suppression. Further, the well-known skyhook control
scheme and an adaptive sliding mode controller are also included in
the simulation for comparison with the proposed FSMC.
Abstract: The aim of this paper is to present a new
three-dimensional proportional-pursuit coupled (PP) guidance law to
track highly maneuverable aircraft. Utilizing a 3-D polar coordinate frame, the PP guidance law is formed by collecting proportional
navigation guidance in Z-R plane and pursuit guidance in X-Y plane.
Feedback linearization control method to solve the guidance
accelerations is used to implement PP guidance. In order to
compensate the actuator time delay, the time delay compensated
version of PP guidance law (CPP) was derived and proved the
effectiveness of modifying the problem of high acceleration in the final
phase of pursuit guidance and improving the weak robustness of
proportional navigation. The simulation results for intercepting Max G
turn situation show that the proposed proportional-pursuit coupled
guidance law guidance law with actuator delay compensation (CPP)
possesses satisfactory robustness and performance.
Abstract: The migration of a deformable drop in simple shear
flow at finite Reynolds numbers is investigated numerically by
solving the full Navier-Stokes equations using a finite
difference/front tracking method. The objectives of this study are to
examine the effectiveness of the present approach to predict the
migration of a drop in a shear flow and to investigate the behavior of
the drop migration with different drop sizes and non-unity viscosity
ratios. It is shown that the drop deformation depends strongly on the
capillary number, so that; the proper non-dimensional number for the
interfacial tension is the capillary number. The rate of migration
increased with increasing the drop radius. In other words, the
required time for drop migration to the centreline decreases. As the
viscosity ratio increases, the drop rotates more slowly and the
lubrication force becomes stronger. The increased lubrication force
makes it easier for the drop to migrate to the centre of the channel.
The migration velocity of the drop vanishes as the drop reaches the
centreline under viscosity ratio of one and non-unity viscosity ratios.
To validate the present calculations, some typical results are
compared with available experimental and theoretical data.
Abstract: In this chapter, we have studied Variation of velocity in incompressible fluid over a moving surface. The boundary layer equations are on a fixed or continuously moving flat plate in the same or opposite direction to the free stream with suction and injection. The boundary layer equations are transferred from partial differential equations to ordinary differential equations. Numerical solutions are obtained by using Runge-Kutta and Shooting methods. We have found numerical solution to velocity and skin friction coefficient.
Abstract: Behavior of dams against the seismic loads has been
studied by many researchers. Most of them proposed new numerical
methods to investigate the dam safety. In this paper, to study the
effect of nonlinear parameters of concrete in gravity dams, a twodimensional
approach was used including the finite element method,
staggered method and smeared crack approach. Effective parameters
in the models are physical properties of concrete such as modulus of
elasticity, tensile strength and specific fracture energy. Two different
models were used in foundation (mass-less and massed) in order to
determine the seismic response of concrete gravity dams. Results
show that when the nonlinear analysis includes the dam- foundation
interaction, the foundation-s mass, flexibility and radiation damping
are important in gravity dam-s response.
Abstract: Fishing has always been an essential component of
the Polynesians- life. Fishhooks, mostly in pearl shell, found during
archaeological excavations are the artifacts related to this activity the
most numerous. Thanks to them, we try to reconstruct the ancient
techniques of resources exploitation, inside the lagoons and offshore.
They can also be used as chronological and cultural indicators. The
shapes and dimensions of these artifacts allow comparisons and
classifications used in both functional approach and chrono-cultural
perspective. Hence it is very important for the ethno-archaeologists
to dispose of reliable methods and standardized measurement of
these artifacts. Such a reliable objective and standardized method
have been previously proposed. But this method cannot be envisaged
manually because of the very important time required to measure
each fishhook manually and the quantity of fishhooks to measure
(many hundreds). We propose in this paper a detailed acquisition
protocol of fishhooks and an automation of every step of this method.
We also provide some experimental results obtained on the fishhooks
coming from three archaeological excavations sites.
Abstract: OLAP uses multidimensional structures, to provide
access to data for analysis. Traditionally, OLAP operations are more
focused on retrieving data from a single data mart. An exception is
the drill across operator. This, however, is restricted to retrieving
facts on common dimensions of the multiple data marts. Our concern
is to define further operations while retrieving data from multiple
data marts. Towards this, we have defined six operations which
coalesce data marts. While doing so we consider the common as well
as the non-common dimensions of the data marts.
Abstract: Recent fifteen years witnessed fast improvements in the field of humanoid robotics. The human-like robot structure is
more suitable to human environment with its supreme obstacle avoidance properties when compared with wheeled service robots.
However, the walking control for bipedal robots is a challenging task
due to their complex dynamics. Stable reference generation plays a very important role in control.
Linear Inverted Pendulum Model (LIPM) and the Zero Moment Point (ZMP) criterion are applied in a number of studies for stable
walking reference generation of biped walking robots. This paper follows this main approach too. We propose a natural and continuous ZMP reference trajectory for a stable and human-like walk. The ZMP reference trajectories move forward under the sole of the support foot when the robot body is supported by a single leg. Robot center of mass trajectory is obtained
from predefined ZMP reference trajectories by a Fourier series
approximation method. The Gibbs phenomenon problem common with Fourier approximations of discontinuous functions is avoided by employing continuous ZMP references. Also, these ZMP reference
trajectories possess pre-assigned single and double support phases,
which are very useful in experimental tuning work.
The ZMP based reference generation strategy is tested via threedimensional
full-dynamics simulations of a 12-degrees-of-freedom
biped robot model. Simulation results indicate that the proposed reference trajectory generation technique is successful.
Abstract: In this study, we present a new and fast algorithm for lung segmentation using CTA images. This process is quite important especially at lung vessel segmentation, detection of pulmonary emboly, finding nodules or segmentation of airways. Applied method has been carried out at four steps. At first step, images have been applied optimal threshold. At the second one, the subsegment vessels, which have a place in lung region and which are in small dimension, have been removed. At the third one, identifying and segmentation of lungs and airway edges have been carried out. Lastly, by throwing away the airway, lung segmentation has been presented.
Abstract: Despite the fact that Knowledge Sharing (KS) is very important, we found only little discussion about the reasons why people have the willingness to share knowledge at such platform even though there is no immediate benefit to the persons who contribute knowledge in it. The aim of this study is to develop an integrative understanding of the factors that support or inhibit individuals- knowledge sharing intentions in virtual communities and to find whether habit would generate people-s willingness to be involved. We apply Social Capital Theory (SCT), and we also add two dimensions for discussion: member incentive and habitual domain (HD). This research assembles the questionnaire from individuals who have experienced knowledge sharing in virtual communities, and applies survey and Structural Equation Model (SEM) to analyze the results from the questionnaires. Finally, results confirm that individuals are willing to share knowledge in virtual communities: (1) if they consider reciprocity, centrality, and have longer tenure in their field, and enjoy helping. (2) if they have the habit of sharing knowledge. This study is useful for the developers of virtual communities to insight into knowledge sharing in cyberspace.
Abstract: Islamic institutions in Malaysia play a variety of
socioeconomic roles such as poverty alleviation. To perform this role,
these institutions face a major task in identifying the poverty group.
Most of these institutions measure and operationalize poverty from
the monetary perspective using variables such as income, expenditure
or consumption. In practice, most Islamic institutions in Malaysia use
the monetary approach in measuring poverty through the
conventional Poverty Line Income (PLI) method and recently, the
had al kifayah (HAK) method using total necessities of a household
from an Islamic perspective. The objective of this paper is to present
the PLI and also the HAK method. This micro-data study would
highlight the similarities and differences of both the methods.A
survey aided by a structured questionnaire was carried out on 260
selected head of households in the state of Selangor. The paper
highlights several demographic factors that are associated with the
three monetary indicators in the study, namely income, PLI and
HAK. In addition, the study found that these monetary variables are
significantly related with each other.
Abstract: HIV-1 genome is highly heterogeneous. Due to this
variation, features of HIV-I genome is in a wide range. For this
reason, the ability to infection of the virus changes depending on
different chemokine receptors. From this point of view, R5 HIV
viruses use CCR5 coreceptor while X4 viruses use CXCR5 and
R5X4 viruses can utilize both coreceptors. Recently, in
Bioinformatics, R5X4 viruses have been studied to classify by using
the experiments on HIV-1 genome.
In this study, R5X4 type of HIV viruses were classified using
Auto Regressive (AR) model through Artificial Neural Networks
(ANNs). The statistical data of R5X4, R5 and X4 viruses was
analyzed by using signal processing methods and ANNs. Accessible
residues of these virus sequences were obtained and modeled by AR
model since the dimension of residues is large and different from
each other. Finally the pre-processed data was used to evolve various
ANN structures for determining R5X4 viruses. Furthermore ROC
analysis was applied to ANNs to show their real performances. The
results indicate that R5X4 viruses successfully classified with high
sensitivity and specificity values training and testing ROC analysis
for RBF, which gives the best performance among ANN structures.